- 16 Mar, 2015 17 commits
-
-
Zhaoyang Liu authored
This patch removes BA setup helper routines mwifiex_is_bastream_setup and mwifiex_is_amsdu_in_ampdu_allowed. Current code will use two functions to check bastream setup and amsdu in ampdu. This patch change these functions to flags, thus avoiding redundant spin_lock check while dequeuing TX packets. Signed-off-by:
Zhaoyang Liu <liuzy@marvell.com> Reviewed-by:
Cathy Luo <cluo@marvell.com> Reviewed-by:
Avinash Patil <patila@marvell.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Shengzhen Li authored
Current code does not check whether main_work_queue or rx_work_queue is running when preparing to do queue_work, this code fix add check before calling queue_work, reducing unnecessary queue_work switch. This change instead sets more_task flag to ensure we run main_process superloop once again. Signed-off-by:
Shengzhen Li <szli@marvell.com> Signed-off-by:
Amitkumar Karwar <akarwar@marvell.com> Reviewed-by:
-
Avinash Patil authored
SD8897 support buffers of 4K and 16 such ports can be accomodated. So basically 64K buffer size in single aggregation is supported. Signed-off-by:
-
Avinash Patil authored
Rename this function to reflect its purpose correctly. Signed-off-by:
-
Avinash Patil authored
A crash was detected while changing virtual interface type is in progress. This was tracked to race condition in accessing bss_priority table while change is in progress. This patch ensures that main_process and rx_process works are locked while we change virtual interface. Signed-off-by:
-
Nicolas Iooss authored
In struct wl18xx_acx_rx_rate_stat, rx_frames_per_rates field is an array, not a number. This means WL18XX_DEBUGFS_FWSTATS_FILE can't be used to display this field in debugfs (it would display a pointer, not the actual data). Use WL18XX_DEBUGFS_FWSTATS_FILE_ARRAY instead. This bug has been found by adding a __printf attribute to wl1271_format_buffer. gcc complained about "format '%u' expects argument of type 'unsigned int', but argument 5 has type 'u32 *'". Fixes: c5d94169 ("wl18xx: use new fw stats structures") Signed-off-by:
Nicolas Iooss <nicolas.iooss_linux@m4x.org> Signed-off-by:
-
Sebastian Andrzej Siewior authored
I have here FRITZ!WLAN USB Stick N v2 / idVendor=057c, idProduct=8501 and every single of this requests ends up with: |ieee80211 phy0: rt2x00usb_vendor_request: Error - Vendor Request 0x0c failed for offset 0x0000 with error -32 I was browsing the the vedor code and I haven't seen such request so I remove it with this patch. If I wasn't look enough or if this error is expected then please excuse :) Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
-
Sebastian Andrzej Siewior authored
rt2800usb_autorun_detect() blindly assumes assumes that it worked while it could have failed. Check the error code here. Signed-off-by:
-
Sebastian Andrzej Siewior authored
My understanding ist that rt2x00usb_register_read() is void and so the reader is unaware of read errors and assumes that whatever was on the stack as it was about to read. Signed-off-by:
-
Amitkumar Karwar authored
We might be in interrupt context at few places. So replace del_timer_sync() with del_timer(). This patch fixes a kernel trace problem seen occasionally during our testing. Signed-off-by:
-
Maithili Hinge authored
This patch adds support for auto ARP feature in mwifiex. The device will respond to ARP requests from the network with ARP response in suspended state without waking up the host. This feature is enabled in the driver by default. Signed-off-by:
Maithili Hinge <maithili@marvell.com> Signed-off-by:
-
Cathy Luo authored
It's been observed Rx aggregated packets are always followed by a single Rx packet. This patch improves our logic to add that extra packet in next aggregation. Signed-off-by:
-
Priit Laes authored
This function is used only by rtl8821ae so move it there Signed-off-by:
Priit Laes <plaes@plaes.org> Signed-off-by:
-
Priit Laes authored
Signed-off-by:
-
Zefir Kurtisi authored
Signed-off-by:
Zefir Kurtisi <zefir.kurtisi@neratec.com> Signed-off-by:
-
Zefir Kurtisi authored
In HT40 modes, pulse events on primary and extension channel are processed individually. If valid, a pulse event will be fed into the detector * for primary frequency, or * for extension frequency (+/-20MHz based on HT40-mode) * or both With that, a 40MHz radar will result in two individual radar events. Signed-off-by:
-
Zefir Kurtisi authored
To support HT40 DFS mode, a triggering detector must reset only itself but not other detector lines. Signed-off-by:
-
- 13 Mar, 2015 23 commits
-
-
Rafał Miłecki authored
This reverts commit b09f5ec1. Now that we have fully working BCMA_DRIVER_PCI symbol (in can be safely disabled), there is no risk bcma will try to use PCI code without PCI available. Signed-off-by:
Rafał Miłecki <zajec5@gmail.com> Signed-off-by:
-
Rafał Miłecki authored
It isn't required for bcma bus on SoCs, so provide some empty functions and allow disabling it. Signed-off-by:
-
Rafał Miłecki authored
This function isn't really related to any bus core. It touches PCI device config registers only, so move it to the (PCI) host file. Signed-off-by:
-
Taehee Yoo authored
Remove unnecessary parameter in rtl8192cu/hw.c Signed-off-by:
Taehee Yoo <ap420073@gmail.com> Signed-off-by:
-
Julia Lawall authored
The semantic patch that fixes this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @r@ type T; identifier f; @@ static T f (...) { ... } @@ identifier r.f; declarer name EXPORT_SYMBOL_GPL; @@ -EXPORT_SYMBOL_GPL(f); // </smpl> Signed-off-by:
Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by:
-
Arend van Spriel authored
The watchdog timer is used to put the device in a low-power mode when it is idle for some time. This timer is stopped during that mode and should be restarted upon activity. This has been broken by commit d4150fced0365 ("brcmfmac: Simplify watchdog sleep."). This patch restores the behaviour as it was before that commit. Reported-by:Pontus Fuchs <pontusf@broadcom.com> Reviewed-by:
Hante Meuleman <meuleman@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by:
Arend van Spriel <arend@broadcom.com> Signed-off-by:
-
Arend van Spriel authored
The firmware provides pointer to SDIO shared information at end of RAM during firmware initialization. End of RAM is obviously determined by the actual ram size, but part of that may be used for save&restore memory. In that case another location in RAM will hold the pointer. Reviewed-by:
-
Arend van Spriel authored
Instead of hard-coded memory sizes it is possible to obtain that information from the internal memory registers. Reviewed-by:
Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by:
-
Arend van Spriel authored
Make the brcmf_chip_attach() function responsible for putting the device in a state where it is accessible for firmware download. Reviewed-by:
-
Arend van Spriel authored
The functions brcmf_chip_[enter/exit]_download() are not exclusively used for firmware download so rename these more appropriate. Reviewed-by:
-
Arend van Spriel authored
Instead of checking the cores in the chip only if CONFIG_BRCMDBG is selected perform the check always and extend it with more sanity checking. Reviewed-by:
-
Arend van Spriel authored
Removing the ramsize from the brcmf_sdio structure to avoid duplication. The information is available in brcmf_chip structure. Reviewed-by:
-
Florian Westphal authored
pre-requisite to shrink size of ieee80211_tx_info which in turn is needed to shrink skb->cb to 40 bytes again. Signed-off-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
-
Florian Westphal authored
If we want to shrink skb->cb then we'd have to see about reducing struct ieee80211_tx_info, which gets embedded inside skb->cb[]. It provides a scratch space to be used by wireless drivers. ar5523 uses the maximum space available today (40 bytes), but it seems we don't need this -- data->skb pointer seems to always point back to the skb whose cb buffer the data structure resides, iow, given a pointer to the embedded control buffer we can infer the skb address. Tested-by:
Pontus Fuchs <pontus.fuchs@gmail.com> Signed-off-by:
-
Sujith Manoharan authored
Since the RTT registers need to be configured for all valid chains irrespective of the runtime chainmask, use the actual chainmask of the chip. Signed-off-by:
Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by:
-
Sujith Manoharan authored
When assigning the initvals for PCIE sleep/awake registers, check the configuration that has been assigned to pll_pwrsave during initialization. Also, display a warning if we don't have valid arrays. Signed-off-by:
-
Sujith Manoharan authored
Cards based on AR9462/AR9565 support more PCIE power save mechanisms, so register them correctly. Signed-off-by:
-
Sujith Manoharan authored
Use the value in ah->config.pll_pwrsave to determine which array needs to be loaded. Also, initialize pll_pwrsave to 1 by default. Signed-off-by:
-
Sujith Manoharan authored
These will be used to handle chip-specific power save configuration. Signed-off-by:
-
Vladimir Kondratiev authored
For the AP, configuration may say not to bridge traffic between wireless clients. This is conveyed from user space (ex: hostapd has ap_isolate parameter) with NL80211_CMD_SET_BSS, to the driver's cfg80211 ops method change_bss Add support for this setting. Signed-off-by:
Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by:
-
Vladimir Kondratiev authored
This is for AP only. If Rx data frame targeted to one of associated clients, transmit it back to the wireless media and don't deliver to the host. For the multicast frames, deliver to both host and wireless media. Signed-off-by:
-
Vladimir Kondratiev authored
It is expected that driver completes NAPI when less than full budget is consumed. Fulfill this requirement. Signed-off-by:
-
Syed Asifful Dayyan authored
These changes add support for BCM4345 SDIO chipset. Reviewed-by:
Daniel (Deognyoun) Kim <dekim@broadcom.com> Signed-off-by:
Syed Asifful Dayyan <syedd@broadcom.com> Signed-off-by:
-
