Until now, struct mreq has not been recognized and it was worked with
as with struct in_addr. That means imr_multiaddr was copied to
imr_address. So do recognize struct mreq here and copy that correctly.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The GPIO pins select which sub bus is connected to the master.

Initially tested with an sn74cbtlv3253 switch device wired into the
MDIO bus.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a somewhat generic framework for MDIO bus
multiplexers.  It is modeled on the I2C multiplexer.

The multiplexer is needed if there are multiple PHYs with the same
address connected to the same MDIO bus adepter, or if there is
insufficient electrical drive capability for all the connected PHY
devices.

Conceptually it could look something like this:

                   ------------------
                   | Control Signal |
                   --------+---------
                           |
 ---------------   --------+------
 | MDIO MASTER |---| Multiplexer |
 ---------------   --+-------+----
                     |       |
                     C       C
                     h       h
                     i       i
                     l       l
                     d       d
                     |       |
     ---------       A       B   ---------
     |       |       |       |   |       |
     | PHY@1 +-------+       +---+ PHY@1 |
     |       |       |       |   |       |
     ---------       |       |   ---------
     ---------       |       |   ---------
     |       |       |       |   |       |
     | PHY@2 +-------+       +---+ PHY@2 |
     |       |                   |       |
     ---------                   ---------

This framework configures the bus topology from device tree data.  The
mechanics of switching the multiplexer is left to device specific
drivers.

The follow-on patch contains a multiplexer driven by GPIO lines.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add of_mdio_find_bus() which allows an mii_bus to be located given its
associated the device tree node.

This is needed by the follow-on patch to add a driver for MDIO bus
multiplexers.

The of_mdiobus_register() function is modified so that the device tree
node is recorded in the mii_bus.  Then we can find it again by
iterating over all mdio_bus_class devices.

Because the OF device tree has now become an integral part of the
kernel, this can live in mdio_bus.c (which contains the needed
mdio_bus_class structure) instead of of_mdio.c.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

If Kernel CAPI is compiled without CONFIG_ISDN_CAPI_MIDDLEWARE,
the structure retrieved via capincci_find() is never actually
used, so don't compile that function in that case.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix up some of the readibility deterioration caused by the recent
whitespace coding style cleanup.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

Various functions in the Gigaset driver were using different
conventions for the meaning of their int return values.
Align them to the usual negative error numbers convention.
Inspired-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

Functions clear_at_state and free_strings did the same thing;
drop one of them, keeping the more descriptive name.
Drop a redundant call.
Rename function dealloc_at_states to dealloc_temp_at_states
to clarify its purpose.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix up some of the readibility deterioration caused by the recent
whitespace coding style cleanup.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

An out-of-place "OK" response to the "AT+GMR" (get firmware version)
command turns out to be, more often than not, a delayed response to
a previous command rather than an actual error, so continue waiting
for the version number in that case.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
CC: stable <stable@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

If DISCONNECT_B3_IND was synthesized because of a DISCONNECT_REQ
with existing logical connections, the connection state wasn't
updated accordingly. Also the emitted DISCONNECT_B3_IND message
wasn't included in the debug log as requested.
This patch fixes both of these issues.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
CC: stable <stable@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce a global ratelimit for CAPI message dumps to protect
against possible log flood.
Drop the ratelimit for ignored messages which is now covered by the
global one.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
CC: stable <stable@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

With the recent changes for how we compute the skb truesize it occurs to me
we are probably going to have a lot of calls to skb_end_pointer -
skb->head.  Instead of running all over the place doing that it would make
more sense to just make it a separate inline skb_end_offset(skb) that way
we can return the correct value without having gcc having to do all the
optimization to cancel out skb->head - skb->head.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since there is now only one spot that actually uses "fastpath" there isn't
much point in carrying it.  Instead we can just use a check for skb_cloned
to verify if we can perform the fast-path free for the head or not.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The fast-path for pskb_expand_head contains a check where the size plus the
unaligned size of skb_shared_info is compared against the size of the data
buffer.  This code path has two issues.  First is the fact that after the
recent changes by Eric Dumazet to __alloc_skb and build_skb the shared info
is always placed in the optimal spot for a buffer size making this check
unnecessary.  The second issue is the fact that the check doesn't take into
account the aligned size of shared info.  As a result the code burns cycles
doing a memcpy with nothing actually being shifted.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

PFC stats are only tabulated when PFC is enabled. However in IEEE
mode the ieee_pfc pfc_tc bits were not checked and the calculation
was aborted.

This results in statistics not being reported through ethtool and
possible a false Tx hang occurring when receiving pause frames.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Clear the REQ and GNT bit in the eeprom control register (EECD).
This is required if the eeprom is to be accessed with auto read
EERD register.

After a cold reset this doesn't matter but if PBIST MAC test was
executed before booting, the register was left in a dirty state
(the 2 bits where set), which caused the read operation to time out
and returning 0.

Reference (page 312):
http://download.intel.com/design/network/manuals/316080.pdfReported-by: Aleksandar Igic <aleksandar.igic@dektech.com.au>
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Like other supported (igp) PHYs, the driver needs to be able to force the
master/slave mode on 82577.  Since the code is the same as what already
exists in the code flow for igp PHYs, move it to a new function to be
called for both flows.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

It appears some networks play bad games with the two bits reserved for
ECN. This can trigger false congestion notifications and very slow
transferts.

Since RFC 3168 (6.1.1) forbids SYN packets to carry CT bits, we can
disable TCP ECN negociation if it happens we receive mangled CT bits in
the SYN packet.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Perry Lorier <perryl@google.com>
Cc: Matt Mathis <mattmathis@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Wilmer van der Gaast <wilmer@google.com>
Cc: Ankur Jain <jankur@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Dave Täht <dave.taht@bufferbloat.net>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With multiple cards is hard to figure out which port caused trouble
int the layer2 routines (e.g. got a timeout).
Now we have the informations in the log output.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The timer3 and the activation delay timer need to be independent.
If timer3 fires do not reqest power up we have to send only INFO 0.
Now layer1 pass TBR3 again.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

For certification test it is very useful to change the layer1
timer3 value on runtime.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

To be full preemptiv safe, we cannot handle a L2 timeout in the timer
context itself, we should do all actions via the D-channel thread.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Under some configs it was still not possible to unload the driver,
because the module use count was srewed up.
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tei manager reports current layer 1 state on creation.
On state change it reports it to the socket interface.
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use qdisc_drop() helper where possible.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change updates the link flow control configuration so that we
correctly set the link flow control settings for DCB.  Previously we would
have to call the fc_enable call 8 times, once for each packet buffer.  If
we move that logic into the fc_enable call itself we can avoid multiple
unnecessary register writes.

This change also corrects an issue in which we were only shifting the water
marks for 82599 parts by 6 instead of 10.  This was resulting in us only
using 1/16 of the packet buffer when flow control was enabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We can avoid many of the forward declarations found in ixgbe_common.c by
just reordering things so this patch does that to help cleanup the code.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This change replaces the calls to put_page with calls to __free_page.

Since the FCoE code is able to access order 1 pages I thought it would be a
good idea to change things over to using __free_pages since that is the
preferred approach for freeing pages.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it so that ixgbe_fc_autoneg is a void and always sets the
current_mode.  Previously if the link was down we would return an error,
however there is no harm in simply treating a link down case as a case in
which autoneg simply failed.  This allows us to rely on the return value of
the ixgbe_fc_enable call now since there should be no cases where it
returns an error that would normally be ignored.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This change reorders the mapping of rings to q_vectors in the case that the
number of rings exceeds the number of q_vectors.  Previously we would
allocate the first R/N queues to the first q_vector where R is the number
of rings and N is the number of q_vectors.  Instead of doing this we can do
a better job of interleaving the rings to the CPUs by assigning every Nth
ring to the q_vector.

The below tables illustrate this change for the R = 16 N = 4 case.
          Before patch  After patch
q_vector:  0  1  2  3    0  1  2  3
Rings:     0  4  8 12    0  1  2  3
           1  5  9 13    4  5  6  7
           3  6 10 14    8  9 10 11
           4  7 11 15   12 13 14 15

This should improve the performance for both DCB or ATR when the number of
rings exceeds the number of q_vectors allocated by the adapter.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it so that we can track instances of where a packet was
dropped due to a packet being received when there are no DMA buffers
available in the ring.

For some reason this was only being enabled with RSC, however it makes
more sense to always have this feature on so that we can track any cases
where we might drop a buffer due to an Rx ring being full.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i217 is the next-generation LOM that will be available on systems with the
Lynx Point Platform Controller Hub (PCH) chipset from Intel.  This patch
provides the initial support for the device.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Version bump to 1.11.3-k.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The idea here seems to be to get a 44bit DMA mask working and if this
fails it should fallback to a 32bit DMA mask. The dma_mask variable is
assigned once to 44bit and never updated. pci_set_dma_mask() and
pci_set_consistent_dma_mask() are both implemented as functions so there
is no evil macro which might update dma_mask. Looking at the assembly, I
see a call to dma_set_mask() followed by dma_supported() and then a jump
passed the second dma_set_mask(). The only way to get to second
dma_set_mask() call is by an error code in the first one.

So I hereby remove the check since it looks superfluous. Please ignore
the path if there is black magic involved.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for a skb_head_is_locked helper function.  It is
meant to be used any time we are considering transferring the head from
skb->head to a paged frag.  If the head is locked it means we cannot remove
the head from the skb so it must be copied or we must take the skb as a
whole.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

GRO is very optimistic in skb truesize estimates, only taking into
account the used part of fragments.

Be conservative, and use more precise computation, so that bloated GRO
skbs can be collapsed eventually.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>