- 22 May, 2023 1 commit
-
-
David Epping authored
The term "-supply" is a suffix to regulator names. Signed-off-by:
David Epping <david.epping@missinglinkelectronics.com> Link: https://lore.kernel.org/r/20230519110545.GA18663@nucnuc.mleSigned-off-by:
Mark Brown <broonie@kernel.org>
-
- 18 May, 2023 1 commit
-
-
Ranjani Sridharan authored
In the BE hw_params configuration, the existing code checks if any of the existing FEs are prepared, running, paused or suspended - and skips the configuration in those cases. This allows multiple calls of hw_params which the ALSA state machine supports. This check is not handled for the prepare stage, which can lead to the same BE being prepared multiple times. This patch adds a check similar to that of the hw_params, with the main difference being that the suspended state is allowed: the ALSA state machine allows a transition from suspended to prepared with hw_params skipped. This problem was detected on Intel IPC4/SoundWire devices, where the BE dailink .prepare stage is used to configure the SoundWire stream with a bank switch. Multiple .prepare calls lead to conflicts with the .trigger operation with IPC4 configurations. This problem was not detected earlier on Intel devices, HDaudio BE dailinks detect that the link is already prepared and skip the configuration, and for IPC3 devices there is no BE trigger. Link: https://github.com/thesofproject/sof/issues/7596 Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com Link: https://lore.kernel.org/r/20230517185731.487124-1-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org
-
- 17 May, 2023 2 commits
-
-
Matthias Kaehlcke authored
The rt5682 driver switches its regmap to cache-only when the device suspends and back to regular mode on resume. When the jack detect interrupt fires rt5682_irq() schedules the jack detect work. This can result in invalid reads from the regmap in cache-only mode if the work runs before the device has resumed: [ 56.245502] rt5682 9-001a: ASoC: error at soc_component_read_no_lock on rt5682.9-001a for register: [0x000000f0] -16 Disable the jack detection interrupt during suspend and re-enable it on resume. The driver already schedules the jack detection work on resume, so any state change during suspend is still handled. This is essentially the same as commit f7d00a9b ("SoC: rt5682s: Disable jack detection interrupt during suspend") for the rt5682s. Cc: stable@kernel.org Signed-off-by: Matthias Kaehlcke <mka@chromium.org Reviewed-by: Douglas Anderson <dianders@chromium.org Reviewed-by: Stephen Boyd <swboyd@chromium.org Link: https://lore.kernel.org/r/20230516164629.1.Ibf79e94b3442eecc0054d2b478779cc512d967fc@changeid Signed-off-by: Mark Brown <broonie@kernel.org
-
Ravulapati Vishnu Vardhan Rao authored
When we run syzkaller we get below Out of Bounds error. "KASAN: slab-out-of-bounds Read in regcache_flat_read" Below is the backtrace of the issue: BUG: KASAN: slab-out-of-bounds in regcache_flat_read+0x10c/0x110 Read of size 4 at addr ffffff8088fbf714 by task syz-executor.4/14144 CPU: 6 PID: 14144 Comm: syz-executor.4 Tainted: G W Hardware name: Qualcomm Technologies, Inc. sc7280 CRD platform (rev5+) (DT) Call trace: dump_backtrace+0x0/0x4ec show_stack+0x34/0x50 dump_stack_lvl+0xdc/0x11c print_address_description+0x30/0x2d8 kasan_report+0x178/0x1e4 __asan_report_load4_noabort+0x44/0x50 regcache_flat_read+0x10c/0x110 regcache_read+0xf8/0x5a0 _regmap_read+0x45c/0x86c _regmap_update_bits+0x128/0x290 regmap_update_bits_base+0xc0/0x15c snd_soc_component_update_bits+0xa8/0x22c snd_soc_component_write_field+0x68/0xd4 tx_macro_put_dec_enum+0x1d0/0x268 snd_ctl_elem_write+0x288/0x474 By Error checking and checking valid values issue gets rectifies. Signed-off-by: Ravulapati Vishnu Vardhan Rao <quic_visr@quicinc.com Link: https://lore.kernel.org/r/20230511112532.16106-1-quic_visr@quicinc.com Signed-off-by: Mark Brown <broonie@kernel.org
-
- 15 May, 2023 20 commits
-
-
Mark Brown authored
Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>: With additional testing with multiple links and multiple DAI types, we found a couple of mistakes with refcounts, base address, missing initialization. A new helper was also added due to a change in the SoundWire programming sequences, with the host driver in charge of setting up the DMA channel mapping instead of the firmware.
-
Ranjani Sridharan authored
The memory allocated for the tuples array assumes that there's 1 instance of all tokens already. So for those tokens that have multiple instances in topology, we need to exclude the initial instance that has already been accounted for. Fixes: 4fdef47a ("ASoC: SOF: ipc4-topology: Add new tokens for input/output pin format count") Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com Link: https://lore.kernel.org/r/20230515085200.17094-1-peter.ujfalusi@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org
-
Ranjani Sridharan authored
Using the same token ID for both input and output format pin index results in collisions and incorrect pin index getting parsed from topology. Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com Reviewed-by: Paul Olaru <paul.olaru@oss.nxp.com Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com Link: https://lore.kernel.org/r/20230515104403.32207-1-peter.ujfalusi@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org
-
Mark Brown authored
Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>: Three patch to correct error path PM runtime handling in few places. Regards, Peter --- Pierre-Louis Bossart (3): ASoC: SOF: debug: conditionally bump runtime_pm counter on exceptions ASoC: SOF: pcm: fix pm_runtime imbalance in error handling ASoC: SOF: sof-client-probes: fix pm_runtime imbalance in error handling sound/soc/sof/debug.c | 4 ++-- sound/soc/sof/pcm.c | 11 ++++++----- sound/soc/sof/sof-client-probes.c | 14 ++++++++------ 3 files changed, 16 insertions(+), 13 deletions(-) -- 2.40.1 -
Lucas Tanure authored
I'm leaving Cirrus Logic, and will no longer have access to hardware and documentation necessary to be effective in a maintainership role. Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com Link: https://lore.kernel.org/r/20230512154503.741718-1-rf@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org
-
Simon Trimmer authored
Flush the SoundWire interrupt handler work instead of cancelling it. When a SoundWire interrupt is triggered the pm_runtime is held until the work has completed. It's therefore unsafe to cancel the work, it must be flushed. Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com Link: https://lore.kernel.org/r/20230512144237.739000-1-rf@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org
-
Ranjani Sridharan authored
Topology could have more instances of the tokens being searched for than the number of sets that need to be copied. Stop copying token after the limit of number of token instances has been reached. This worked before only by chance as we had allocated more size for the tuples array than the number of actual tokens being parsed. Fixes: 7006d20e ("ASoC: SOF: Introduce IPC3 ops") Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com Link: https://lore.kernel.org/r/20230512114630.24439-1-peter.ujfalusi@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org
-
Kai Vehmanen authored
If there are failures in DSP runtime resume, the device state will not reach active and this makes it impossible e.g. to retrieve a possible DSP panic dump via "exception" debugfs node. If CONFIG_SND_SOC_SOF_DEBUG_ENABLE_DEBUGFS_CACHE=y is set, the data in cache is stale. If debugfs cache is not used, the region simply cannot be read. To allow debugging these scenarios, update the debugfs cache contents in resume error handler. User-space can then later retrieve DSP panic and other state via debugfs (requires SOF debugfs cache to be enabled in build). Reported-by: Curtis Malainey <cujomalainey@chromium.org Link: https://github.com/thesofproject/linux/issues/4274 Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com Reviewed-by: Curtis Malainey <cujomalainey@chromium.org Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com Link: https://lore.kernel.org/r/20230512104638.21376-1-peter.ujfalusi@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org
-
Krzysztof Kozlowski authored
Remove Krzysztof Kozlowski from maintainer of Samsung SoC Audio drivers and change the status to maintenance (no one is reality being paid for looking at this). Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com Link: https://lore.kernel.org/r/20230513090228.4340-1-krzysztof.kozlowski@linaro.org Signed-off-by: Mark Brown <broonie@kernel.org
-
Douglas Anderson authored
When devm runs function in the "remove" path for a device it runs them in the reverse order. That means that if you have parts of your driver that aren't using devm or are using "roll your own" devm w/ devm_add_action_or_reset() you need to keep that in mind. The mt8186 audio driver didn't quite get this right. Specifically, in mt8186_init_clock() it called mt8186_audsys_clk_register() and then went on to call a bunch of other devm function. The caller of mt8186_init_clock() used devm_add_action_or_reset() to call mt8186_deinit_clock() but, because of the intervening devm functions, the order was wrong. Specifically at probe time, the order was: 1. mt8186_audsys_clk_register() 2. afe_priv->clk = devm_kcalloc(...) 3. afe_priv->clk[i] = devm_clk_get(...) At remove time, the order (which should have been 3, 2, 1) was: 1. mt8186_audsys_clk_unregister() 3. Free all of afe_priv->clk[i] 2. Free afe_priv->clk The above seemed to be causing a use-after-free. Luckily, it's easy to fix this by simply using devm more correctly. Let's move the devm_add_action_or_reset() to the right place. In addition to fixing the use-after-free, code inspection shows that this fixes a leak (missing call to mt8186_audsys_clk_unregister()) that would have happened if any of the syscon_regmap_lookup_by_phandle() calls in mt8186_init_clock() had failed. Fixes: 55b423d5 ("ASoC: mediatek: mt8186: support audio clock control in platform driver") Signed-off-by: Douglas Anderson <dianders@chromium.org Link: https://lore.kernel.org/r/20230511092437.1.I31cceffc8c45bb1af16eb613e197b3df92cdc19e@changeid Signed-off-by: Mark Brown <broonie@kernel.org
-
Peter Ujfalusi authored
The commands in sof_ipc_dai_config.flags are encoded as bits: 1 (bit0) - hw_params 2 (bit1) - hw_free 4 (bit2) - pause These are commands, they cannot be combined as one would assume, for example 3 (bit0 | bit1) is invalid. This can happen right at the second start of a stream as at the end of the first stream we set the hw_free command (bit1) and on the second start we would OR on top of it the hw_params (bit0). Fixes: b66bfc3a ("ASoC: SOF: sof-audio: Fix broken early bclk feature for SSP") Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com Link: https://lore.kernel.org/r/20230512110317.5180-1-peter.ujfalusi@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org
-
Pierre-Louis Bossart authored
When an error occurs, we need to make sure the device can pm_runtime suspend instead of keeping it active. Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com Link: https://lore.kernel.org/r/20230512103315.8921-4-peter.ujfalusi@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org
-
Pierre-Louis Bossart authored
When an error occurs, we need to make sure the device can pm_runtime suspend instead of keeping it active. Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com Link: https://lore.kernel.org/r/20230512103315.8921-3-peter.ujfalusi@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org
-
Pierre-Louis Bossart authored
When a firmware IPC error happens during a pm_runtime suspend, we ignore the error and suspend anyways. However, the code unconditionally increases the runtime_pm counter. This results in a confusing configuration where the code will suspend, resume but never suspend again due to the use of pm_runtime_get_noresume(). The intent of the counter increase was to prevent entry in D3, but if that transition to D3 is already started it cannot be stopped. In addition, there's no point in that case in trying to prevent anything, the firmware error is handled and the next resume will re-initialize the firmware completely. This patch changes the logic to prevent suspend when the device is pm_runtime active and has a use_count > 0. Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com Link: https://lore.kernel.org/r/20230512103315.8921-2-peter.ujfalusi@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org
-
Pierre-Louis Bossart authored
These registers enable the HDaudio DMA hardware to split/merge data from different PDIs, possibly on different links. This capability exists for all types of HDaudio extended links, but for now is only required for SoundWire. In the SSP/DMIC case, the IP is programmed by the DSP firmware. Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com Reviewed-by: Rander Wang <rander.wang@intel.com Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com Link: https://lore.kernel.org/r/20230512174611.84372-7-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org
-
Pierre-Louis Bossart authored
We defined the values but never initialized it for SoundWire/SSP, fix this miss. A Fixes: tag is not provided as instance_offset was not used so far, so nothing was really broken. This patch is only required for the SoundWire support in the following patch. Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com Reviewed-by: Rander Wang <rander.wang@intel.com Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com Link: https://lore.kernel.org/r/20230512174611.84372-6-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org
-
Pierre-Louis Bossart authored
We mix the use of hlink->ml_addr and the 'ml_addr' parameter. It's the same thing, let's align on using the parameter. Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com Reviewed-by: Rander Wang <rander.wang@intel.com Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com Link: https://lore.kernel.org/r/20230512174611.84372-5-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org
-
Pierre-Louis Bossart authored
The base_ptr value needs to be derived from the remap_addr pointer, not the ml_addr. This base_ptr was used only in debug logs that were so far not contributed upstream so the issue was not detected. It needs to be fixed for SoundWire support on LunarLake. Fixes: 17c9b6ec ("ASoC: SOF: Intel: hda-mlink: add structures to parse ALT links") Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com Reviewed-by: Rander Wang <rander.wang@intel.com Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com Link: https://lore.kernel.org/r/20230512174611.84372-4-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org
-
Pierre-Louis Bossart authored
Same functionality as for DMIC/SSP with different ID. Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com Reviewed-by: Rander Wang <rander.wang@intel.com Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com Link: https://lore.kernel.org/r/20230512174611.84372-3-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org
-
Pierre-Louis Bossart authored
In hindsight it was a very bad idea to use the same refcount for Extended and 'legacy' HDaudio multi-links. The existing solution only powers-up the first sublink, which causes SoundWire and SSP tests to fail when more than one DAI is used concurrently. Solving this problem requires per-sublink refcounting, as suggested in this patch. The existing refcounting remains for 'legacy' HdAudio links, mainly to avoid changing the obscure programming sequence in snd_hdac_ext_bus_link_put(). Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com Link: https://lore.kernel.org/r/20230512174611.84372-2-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org
-
- 12 May, 2023 1 commit
-
-
Paweł Anikiel authored
Apply a workaround for what appears to be a hardware quirk. The problem seems to happen when enabling "whole chip power" (bit D7 register R6) for the very first time after the chip receives power. If either "output" (D4) or "DAC" (D3) aren't powered on at that time, playback becomes very distorted later on. This happens on the Google Chameleon v3, as well as on a ZYBO Z7-10: https://ez.analog.com/audio/f/q-a/543726/solved-ssm2603-right-output-offset-issue/480229 I suspect this happens only when using an external MCLK signal (which is the case for both of these boards). Here are some experiments run on a Google Chameleon v3. These were run in userspace using a wrapper around the i2cset utility: ssmset() { i2cset -y 0 0x1a $(($1*2)) $2 } For each of the following sequences, we apply power to the ssm2603 chip, set the configuration registers R0-R5 and R7-R8, run the selected sequence, and check for distortions on playback. ssmset 0x09 0x01 # core ssmset 0x06 0x07 # chip, out, dac OK ssmset 0x09 0x01 # core ssmset 0x06 0x87 # out, dac ssmset 0x06 0x07 # chip OK (disable MCLK) ssmset 0x09 0x01 # core ssmset 0x06 0x1f # chip ssmset 0x06 0x07 # out, dac (enable MCLK) OK ssmset 0x09 0x01 # core ssmset 0x06 0x1f # chip ssmset 0x06 0x07 # out, dac NOT OK ssmset 0x06 0x1f # chip ssmset 0x09 0x01 # core ssmset 0x06 0x07 # out, dac NOT OK ssmset 0x09 0x01 # core ssmset 0x06 0x0f # chip, out ssmset 0x06 0x07 # dac NOT OK ssmset 0x09 0x01 # core ssmset 0x06 0x17 # chip, dac ssmset 0x06 0x07 # out NOT OK For each of the following sequences, we apply power to the ssm2603 chip, run the selected sequence, issue a reset with R15, configure R0-R5 and R7-R8, run one of the NOT OK sequences from above, and check for distortions. ssmset 0x09 0x01 # core ssmset 0x06 0x07 # chip, out, dac OK (disable MCLK) ssmset 0x09 0x01 # core ssmset 0x06 0x07 # chip, out, dac (enable MCLK after reset) NOT OK ssmset 0x09 0x01 # core ssmset 0x06 0x17 # chip, dac NOT OK ssmset 0x09 0x01 # core ssmset 0x06 0x0f # chip, out NOT OK ssmset 0x06 0x07 # chip, out, dac NOT OK Signed-off-by: Paweł Anikiel <pan@semihalf.com Link: https://lore.kernel.org/r/20230508113037.137627-8-pan@semihalf.com Signed-off-by: Mark Brown <broonie@kernel.org
-
- 11 May, 2023 2 commits
-
-
Martin Povišer authored
A bunch of TI's codecs have binding schemas which force #sound-dai-cells to one despite those codecs only having a single DAI. Allow for bindings with zero DAI cells and deprecate the former non-zero value. Signed-off-by: Martin Povišer <povik+lin@cutebit.org Link: https://lore.kernel.org/r/20230509153412.62847-1-povik+lin@cutebit.org Signed-off-by: Mark Brown <broonie@kernel.org
-
Aidan MacDonald authored
When the CPU supplies bit/frame clocks, the system clock (clk_i2s) is divided to produce the bit clock. This is a simple 1/N divider with a fairly limited range, so for a given system clock frequency only a few sample rates can be produced. Usually a wider range of sample rates is supported by varying the system clock frequency. The old calculation method was not very robust and could easily produce the wrong clock rate, especially with non-standard rates. For example, if the system clock is 1.99x the target bit clock rate, the divider would be calculated as 1 instead of the more accurate 2. Instead, use a more accurate method that considers two adjacent divider settings and selects the one that produces the least error versus the requested rate. If the error is 5% or higher then the rate setting is rejected to prevent garbled audio. Skip divider calculation when the codec is supplying both the bit and frame clock; in that case, the divider outputs are unused and we don't want to constrain the sample rate. Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com Link: https://lore.kernel.org/r/20230509125134.208129-1-aidanmacdonald.0x0@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org
-
- 09 May, 2023 1 commit
-
-
V sujith kumar Reddy authored
Check substream and runtime variables before assigning. Signed-off-by: V sujith kumar Reddy <Vsujithkumar.Reddy@amd.com Link: https://lore.kernel.org/r/20230508070510.6100-1-Vsujithkumar.Reddy@amd.com Signed-off-by: Mark Brown <broonie@kernel.org
-
- 08 May, 2023 3 commits
-
-
Shengjiu Wang authored
There is error message when defer probe happens: fsl-micfil-dai 30ca0000.micfil: Unbalanced pm_runtime_enable! Fix the error handler with pm_runtime_enable and add fsl_micfil_remove() for pm_runtime_disable. Fixes: 47a70e6f ("ASoC: Add MICFIL SoC Digital Audio Interface driver.") Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com Link: https://lore.kernel.org/r/1683540996-6136-1-git-send-email-shengjiu.wang@nxp.com Signed-off-by: Mark Brown <broonie@kernel.org
-
Maxim Kochetkov authored
On slow CPU (FPGA/QEMU emulated) printing overrun messages from interrupt handler to uart console may leads to more overrun errors. So use dev_err_ratelimited to limit the number of error messages. Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru Link: https://lore.kernel.org/r/20230505062820.21840-1-fido_max@inbox.ru Signed-off-by: Mark Brown <broonie@kernel.org
-
Jeremy Soller authored
Add pang12 quirk to enable the internal microphone. Signed-off-by: Jeremy Soller <jeremy@system76.com Signed-off-by: Tim Crawford <tcrawford@system76.com Link: https://lore.kernel.org/r/20230505161458.19676-1-tcrawford@system76.com Signed-off-by: Mark Brown <broonie@kernel.org
-
- 07 May, 2023 8 commits
-
-
Linus Torvalds authored
-
Linus Torvalds authored
Merge tag 'perf-tools-for-v6.4-3-2023-05-06' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux Pull perf tool updates from Arnaldo Carvalho de Melo: "Third version of perf tool updates, with the build problems with with using a 'vmlinux.h' generated from the main build fixed, and the bpf skeleton build disabled by default. Build: - Require libtraceevent to build, one can disable it using NO_LIBTRACEEVENT=1. It is required for tools like 'perf sched', 'perf kvm', 'perf trace', etc. libtraceevent is available in most distros so installing 'libtraceevent-devel' should be a one-time event to continue building perf as usual. Using NO_LIBTRACEEVENT=1 produces tooling that is functional and sufficient for lots of users not interested in those libtraceevent dependent features. - Allow Python support in 'perf script' when libtraceevent isn't linked, as not all features requires it, for instance Intel PT does not use tracepoints. - Error if the python interpreter needed for jevents to work isn't available and NO_JEVENTS=1 isn't set, preventing a build without support for JSON vendor events, which is a rare but possible condition. The two check error messages: $(error ERROR: No python interpreter needed for jevents generation. Install python or build with NO_JEVENTS=1.) $(error ERROR: Python interpreter needed for jevents generation too old (older than 3.6). Install a newer python or build with NO_JEVENTS=1.) - Make libbpf 1.0 the minimum required when building with out of tree, distro provided libbpf. - Use libsdtc++'s and LLVM's libcxx's __cxa_demangle, a portable C++ demangler, add 'perf test' entry for it. - Make binutils libraries opt in, as distros disable building with it due to licensing, they were used for C++ demangling, for instance. - Switch libpfm4 to opt-out rather than opt-in, if libpfm-devel (or equivalent) isn't installed, we'll just have a build warning: Makefile.config:1144: libpfm4 not found, disables libpfm4 support. Please install libpfm4-dev - Add a feature test for scandirat(), that is not implemented so far in musl and uclibc, disabling features that need it, such as scanning for tracepoints in /sys/kernel/tracing/events. perf BPF filters: - New feature where BPF can be used to filter samples, for instance: $ sudo ./perf record -e cycles --filter 'period > 1000' true $ sudo ./perf script perf-exec 2273949 546850.708501: 5029 cycles: ffffffff826f9e25 finish_wait+0x5 ([kernel.kallsyms]) perf-exec 2273949 546850.708508: 32409 cycles: ffffffff826f9e25 finish_wait+0x5 ([kernel.kallsyms]) perf-exec 2273949 546850.708526: 143369 cycles: ffffffff82b4cdbf xas_start+0x5f ([kernel.kallsyms]) perf-exec 2273949 546850.708600: 372650 cycles: ffffffff8286b8f7 __pagevec_lru_add+0x117 ([kernel.kallsyms]) perf-exec 2273949 546850.708791: 482953 cycles: ffffffff829190de __mod_memcg_lruvec_state+0x4e ([kernel.kallsyms]) true 2273949 546850.709036: 501985 cycles: ffffffff828add7c tlb_gather_mmu+0x4c ([kernel.kallsyms]) true 2273949 546850.709292: 503065 cycles: 7f2446d97c03 _dl_map_object_deps+0x973 (/usr/lib/x86_64-linux-gnu/ld-linux-x86-64.so.2) - In addition to 'period' (PERF_SAMPLE_PERIOD), the other PERF_SAMPLE_ can be used for filtering, and also some other sample accessible values, from tools/perf/Documentation/perf-record.txt: Essentially the BPF filter expression is: <term> <operator> <value> (("," | "||") <term> <operator> <value>)* The <term> can be one of: ip, id, tid, pid, cpu, time, addr, period, txn, weight, phys_addr, code_pgsz, data_pgsz, weight1, weight2, weight3, ins_lat, retire_lat, p_stage_cyc, mem_op, mem_lvl, mem_snoop, mem_remote, mem_lock, mem_dtlb, mem_blk, mem_hops The <operator> can be one of: ==, !=, >, >=, <, <=, & The <value> can be one of: <number> (for any term) na, load, store, pfetch, exec (for mem_op) l1, l2, l3, l4, cxl, io, any_cache, lfb, ram, pmem (for mem_lvl) na, none, hit, miss, hitm, fwd, peer (for mem_snoop) remote (for mem_remote) na, locked (for mem_locked) na, l1_hit, l1_miss, l2_hit, l2_miss, any_hit, any_miss, walk, fault (for mem_dtlb) na, by_data, by_addr (for mem_blk) hops0, hops1, hops2, hops3 (for mem_hops) perf lock contention: - Show lock type with address. - Track and show mmap_lock, siglock and per-cpu rq_lock with address. This is done for mmap_lock by following the current->mm pointer: $ sudo ./perf lock con -abl -- sleep 10 contended total wait max wait avg wait address symbol ... 16344 312.30 ms 2.22 ms 19.11 us ffff8cc702595640 17686 310.08 ms 1.49 ms 17.53 us ffff8cc7025952c0 3 84.14 ms 45.79 ms 28.05 ms ffff8cc78114c478 mmap_lock 3557 76.80 ms 68.75 us 21.59 us ffff8cc77ca3af58 1 68.27 ms 68.27 ms 68.27 ms ffff8cda745dfd70 9 54.53 ms 7.96 ms 6.06 ms ffff8cc7642a48b8 mmap_lock 14629 44.01 ms 60.00 us 3.01 us ffff8cc7625f9ca0 3481 42.63 ms 140.71 us 12.24 us ffffffff937906ac vmap_area_lock 16194 38.73 ms 42.15 us 2.39 us ffff8cd397cbc560 11 38.44 ms 10.39 ms 3.49 ms ffff8ccd6d12fbb8 mmap_lock 1 5.43 ms 5.43 ms 5.43 ms ffff8cd70018f0d8 1674 5.38 ms 422.93 us 3.21 us ffffffff92e06080 tasklist_lock 581 4.51 ms 130.68 us 7.75 us ffff8cc9b1259058 5 3.52 ms 1.27 ms 703.23 us ffff8cc754510070 112 3.47 ms 56.47 us 31.02 us ffff8ccee38b3120 381 3.31 ms 73.44 us 8.69 us ffffffff93790690 purge_vmap_area_lock 255 3.19 ms 36.35 us 12.49 us ffff8d053ce30c80 - Update default map size to 16384. - Allocate single letter option -M for --map-nr-entries, as it is proving being frequently used. - Fix struct rq lock access for older kernels with BPF's CO-RE (Compile once, run everywhere). - Fix problems found with MSAn. perf report/top: - Add inline information when using --call-graph=fp or lbr, as was already done to the --call-graph=dwarf callchain mode. - Improve the 'srcfile' sort key performance by really using an optimization introduced in 6.2 for the 'srcline' sort key that avoids calling addr2line for comparision with each sample. perf sched: - Make 'perf sched latency/map/replay' to use "sched:sched_waking" instead of "sched:sched_waking", consistent with 'perf record' since d566a9c2 ("perf sched: Prefer sched_waking event when it exists"). perf ftrace: - Make system wide the default target for latency subcommand, run the following command then generate some network traffic and press control+C: # perf ftrace latency -T __kfree_skb ^C DURATION | COUNT | GRAPH | 0 - 1 us | 27 | ############# | 1 - 2 us | 22 | ########### | 2 - 4 us | 8 | #### | 4 - 8 us | 5 | ## | 8 - 16 us | 24 | ############ | 16 - 32 us | 2 | # | 32 - 64 us | 1 | | 64 - 128 us | 0 | | 128 - 256 us | 0 | | 256 - 512 us | 0 | | 512 - 1024 us | 0 | | 1 - 2 ms | 0 | | 2 - 4 ms | 0 | | 4 - 8 ms | 0 | | 8 - 16 ms | 0 | | 16 - 32 ms | 0 | | 32 - 64 ms | 0 | | 64 - 128 ms | 0 | | 128 - 256 ms | 0 | | 256 - 512 ms | 0 | | 512 - 1024 ms | 0 | | 1 - ... s | 0 | | # perf top: - Add --branch-history (LBR: Last Branch Record) option, just like already available for 'perf record'. - Fix segfault in thread__comm_len() where thread->comm was being used outside thread->comm_lock. perf annotate: - Allow configuring objdump and addr2line in ~/.perfconfig., so that you can use alternative binaries, such as llvm's. perf kvm: - Add TUI mode for 'perf kvm stat report'. Reference counting: - Add reference count checking infrastructure to check for use after free, done to the 'cpumap', 'namespaces', 'maps' and 'map' structs, more to come. To build with it use -DREFCNT_CHECKING=1 in the make command line to build tools/perf. Documented at: https://perf.wiki.kernel.org/index.php/Reference_Count_Checking - The above caught, for instance, fix, present in this series: - Fix maps use after put in 'perf test "Share thread maps"': 'maps' is copied from leader, but the leader is put on line 79 and then 'maps' is used to read the reference count below - so a use after put, with the put of maps happening within thread__put. Fixed by reversing the order of puts so that the leader is put last. - Also several fixes were made to places where reference counts were not being held. - Make this one of the tests in 'make -C tools/perf build-test' to regularly build test it and to make sure no direct access to the reference counted structs are made, doing that via accessors to check the validity of the struct pointer. ARM64: - Fix 'perf report' segfault when filtering coresight traces by sparse lists of CPUs. - Add support for 'simd' as a sort field for 'perf report', to show ARM's NEON SIMD's predicate flags: "partial" and "empty". arm64 vendor events: - Add N1 metrics. Intel vendor events: - Add graniterapids, grandridge and sierraforrest events. - Refresh events for: alderlake, aldernaken, broadwell, broadwellde, broadwellx, cascadelakx, haswell, haswellx, icelake, icelakex, jaketown, meteorlake, knightslanding, sandybridge, sapphirerapids, silvermont, skylake, tigerlake and westmereep-dp - Refresh metrics for alderlake-n, broadwell, broadwellde, broadwellx, haswell, haswellx, icelakex, ivybridge, ivytown and skylakex. perf stat: - Implement --topdown using JSON metrics. - Add TopdownL1 JSON metric as a default if present, but disable it for now for some Intel hybrid architectures, a series of patches addressing this is being reviewed and will be submitted for v6.5. - Use metrics for --smi-cost. - Update topdown documentation. Vendor events (JSON) infrastructure: - Add support for computing and printing metric threshold values. For instance, here is one found in thesapphirerapids json file: { "BriefDescription": "Percentage of cycles spent in System Management Interrupts.", "MetricExpr": "((msr@aperf@ - cycles) / msr@aperf@ if msr@smi@ > 0 else 0)", "MetricGroup": "smi", "MetricName": "smi_cycles", "MetricThreshold": "smi_cycles > 0.1", "ScaleUnit": "100%" }, - Test parsing metric thresholds with the fake PMU in 'perf test pmu-events'. - Support for printing metric thresholds in 'perf list'. - Add --metric-no-threshold option to 'perf stat'. - Add rand (reverse and) and has_pmem (optane memory) support to metrics. - Sort list of input files to avoid depending on the order from readdir() helping in obtaining reproducible builds. S/390: - Add common metrics: - CPI (cycles per instruction), prbstate (ratio of instructions executed in problem state compared to total number of instructions), l1mp (Level one instruction and data cache misses per 100 instructions). - Add cache metrics for z13, z14, z15 and z16. - Add metric for TLB and cache. ARM: - Add raw decoding for SPE (Statistical Profiling Extension) v1.3 MTE (Memory Tagging Extension) and MOPS (Memory Operations) load/store. Intel PT hardware tracing: - Add event type names UINTR (User interrupt delivered) and UIRET (Exiting from user interrupt routine), documented in table 32-50 "CFE Packet Type and Vector Fields Details" in the Intel Processor Trace chapter of The Intel SDM Volume 3 version 078. - Add support for new branch instructions ERETS and ERETU. - Fix CYC timestamps after standalone CBR ARM CoreSight hardware tracing: - Allow user to override timestamp and contextid settings. - Fix segfault in dso lookup. - Fix timeless decode mode detection. - Add separate decode paths for timeless and per-thread modes. auxtrace: - Fix address filter entire kernel size. Miscellaneous: - Fix use-after-free and unaligned bugs in the PLT handling routines. - Use zfree() to reduce chances of use after free. - Add missing 0x prefix for addresses printed in hexadecimal in 'perf probe'. - Suppress massive unsupported target platform errors in the unwind code. - Fix return incorrect build_id size in elf_read_build_id(). - Fix 'perf scripts intel-pt-events.py' IPC output for Python 2 . - Add missing new parameter in kfree_skb tracepoint to the python scripts using it. - Add 'perf bench syscall fork' benchmark. - Add support for printing PERF_MEM_LVLNUM_UNC (Uncached access) in 'perf mem'. - Fix wrong size expectation for perf test 'Setup struct perf_event_attr' caused by the patch adding perf_event_attr::config3. - Fix some spelling mistakes" * tag 'perf-tools-for-v6.4-3-2023-05-06' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (365 commits) Revert "perf build: Make BUILD_BPF_SKEL default, rename to NO_BPF_SKEL" Revert "perf build: Warn for BPF skeletons if endian mismatches" perf metrics: Fix SEGV with --for-each-cgroup perf bpf skels: Stop using vmlinux.h generated from BTF, use subset of used structs + CO-RE perf stat: Separate bperf from bpf_profiler perf test record+probe_libc_inet_pton: Fix call chain match on x86_64 perf test record+probe_libc_inet_pton: Fix call chain match on s390 perf tracepoint: Fix memory leak in is_valid_tracepoint() perf cs-etm: Add fix for coresight trace for any range of CPUs perf build: Fix unescaped # in perf build-test perf unwind: Suppress massive unsupported target platform errors perf script: Add new parameter in kfree_skb tracepoint to the python scripts using it perf script: Print raw ip instead of binary offset for callchain perf symbols: Fix return incorrect build_id size in elf_read_build_id() perf list: Modify the warning message about scandirat(3) perf list: Fix memory leaks in print_tracepoint_events() perf lock contention: Rework offset calculation with BPF CO-RE perf lock contention: Fix struct rq lock access perf stat: Disable TopdownL1 on hybrid perf stat: Avoid SEGV on counter->name ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull debugobjects fix from Thomas Gleixner: "A single fix for debugobjects: The recent fix to ensure atomicity of lookup and allocation inadvertently broke the pool refill mechanism, so that debugobject OOMs now in certain situations. The reason is that the functions which got updated no longer invoke debug_objecs_init(), which is now the only place to care about refilling the tracking object pool. Restore the original behaviour by adding explicit refill opportunities to those places" * tag 'core-debugobjects-2023-05-06' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: debugobject: Ensure pool refill (again)
-
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6Linus Torvalds authored
Pull crypto fixes from Herbert Xu: - A long-standing bug in crypto_engine - A buggy but harmless check in the sun8i-ss driver - A regression in the CRYPTO_USER interface * tag 'v6.4-p2' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: crypto: api - Fix CRYPTO_USER checks for report function crypto: engine - fix crypto_queue backlog handling crypto: sun8i-ss - Fix a test in sun8i_ss_setup_ivs()
-
git://git.samba.org/sfrench/cifs-2.6Linus Torvalds authored
Pull cifs fixes from Steve French: "smb3 client fixes, mostly DFS or reconnect related: - Two DFS connection sharing fixes - DFS refresh fix - Reconnect fix - Two potential use after free fixes - Also print prefix patch in mount debug msg - Two small cleanup fixes" * tag '6.4-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6: cifs: Remove unneeded semicolon cifs: fix sharing of DFS connections cifs: avoid potential races when handling multiple dfs tcons cifs: protect access of TCP_Server_Info::{origin,leaf}_fullpath cifs: fix potential race when tree connecting ipc cifs: fix potential use-after-free bugs in TCP_Server_Info::hostname cifs: print smb3_fs_context::source when mounting cifs: protect session status check in smb2_reconnect() SMB3.1.1: correct definition for app_instance_id create contexts
-
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linuxLinus Torvalds authored
Pull clk fixes from Stephen Boyd: "A couple more patches that would be good to get into -rc1: - Revert an i.MX patch that's causing video failures because division math goes sideways - Fix a clang + W=1 build isue where FIELD_PREP() is taking a 32-bit variable instead of the usual u64 type - Fix a Kconfig bug in the StarFive JH7110 clk config that selects a reset controller when it can't be selected" * tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: clk: starfive: Fix RESET_STARFIVE_JH7110 can't be selected in a specified case clk: sp7021: Adjust width of _m in HWM_FIELD_PREP() Revert "clk: imx: composite-8m: Add support to determine_rate" -
git://git.linaro.org/landing-teams/working/fujitsu/integrationLinus Torvalds authored
Pull mailbox updates from Jassi Brar: - mailbox api: allow direct registration to a channel and convert omap and pcc to use mbox_bind_client - omap and hi6220 : use of_property_read_bool - test: fix double-free and use spinlock header - rockchip and bcm-pdc: drop of_match_ptr - mpfs: change config symbol - mediatek gce: support MT6795 - qcom apcs: consolidate of_device_id and support IPQ9574 * tag 'mailbox-v6.4' of git://git.linaro.org/landing-teams/working/fujitsu/integration: dt-bindings: mailbox: qcom: add compatible for IPQ9574 SoC mailbox: qcom-apcs-ipc: do not grow the of_device_id dt-bindings: mailbox: qcom,apcs-kpss-global: use fallbacks for few variants dt-bindings: mailbox: mediatek,gce-mailbox: Add support for MT6795 mailbox: mpfs: convert SOC_MICROCHIP_POLARFIRE to ARCH_MICROCHIP_POLARFIRE mailbox: bcm-pdc: drop of_match_ptr for ID table mailbox: rockchip: drop of_match_ptr for ID table mailbox: mailbox-test: Fix potential double-free in mbox_test_message_write() mailbox: mailbox-test: Explicitly include header for spinlock support mailbox: Use of_property_read_bool() for boolean properties mailbox: pcc: Use mbox_bind_client mailbox: omap: Use mbox_bind_client mailbox: Allow direct registration to a channel
-
git://git.kernel.dk/linuxLinus Torvalds authored
Pull more io_uring updates from Jens Axboe: "Nothing major in here, just two different parts: - A small series from Breno that enables passing the full SQE down for ->uring_cmd(). This is a prerequisite for enabling full network socket operations. Queued up a bit late because of some stylistic concerns that got resolved, would be nice to have this in 6.4-rc1 so the dependent work will be easier to handle for 6.5. - Fix for the huge page coalescing, which was a regression introduced in the 6.3 kernel release (Tobias)" * tag 'for-6.4/io_uring-2023-05-07' of git://git.kernel.dk/linux: io_uring: Remove unnecessary BUILD_BUG_ON io_uring: Pass whole sqe to commands io_uring: Create a helper to return the SQE size io_uring/rsrc: check for nonconsecutive pages
-
- 06 May, 2023 1 commit
-
-
Arnaldo Carvalho de Melo authored
This reverts commit a980755b. We need to better polish building with BPF skels, so revert back to making it an experimental feature that has to be explicitely enabled using BUILD_BPF_SKEL=1. Signed-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com>
-
