commit e461894d upstream.

StrongARM core uses RCSR SMR bit to tell to bootloader that it was reset
by entering the sleep mode. After we have resumed, there is little point
in having that bit enabled. Moreover, if this bit is set before reboot,
the bootloader can become confused. Thus clear the SMR bit on resume
just before clearing the scratchpad (resume address) register.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 7215853e upstream.

Commit 6edb2a8a introduced
an array map_pages that contains the addresses returned by
kmap_atomic. However, when unmapping those pages, map_pages[0]
is unmapped before map_pages[1], breaking the nesting requirement
as specified in the documentation for kmap_atomic/kunmap_atomic.

This was caught by the highmem debug code present in kunmap_atomic.
Fix the loop to do the unmapping properly.

Link: http://lkml.kernel.org/r/1418871056-6614-1-git-send-email-markivx@codeaurora.orgReviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Reported-by: Lime Yang <limey@codeaurora.org>
Signed-off-by: Vikram Mulukutla <markivx@codeaurora.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit cbef8478 upstream.

Migrating hugepages and hwpoisoned hugepages are considered as non-present
hugepages, and they are referenced via migration entries and hwpoison
entries in their page table slots.

This behavior causes race condition because pmd_huge() doesn't tell
non-huge pages from migrating/hwpoisoned hugepages.  follow_page_mask() is
one example where the kernel would call follow_page_pte() for such
hugepage while this function is supposed to handle only normal pages.

To avoid this, this patch makes pmd_huge() return true when pmd_none() is
true *and* pmd_present() is false.  We don't have to worry about mixing up
non-present pmd entry with normal pmd (pointing to leaf level pte entry)
because pmd_present() is true in normal pmd.

The same race condition could happen in (x86-specific) gup_pmd_range(),
where this patch simply adds pmd_present() check instead of pmd_huge().
This is because gup_pmd_range() is fast path.  If we have non-present
hugepage in this function, we will go into gup_huge_pmd(), then return 0
at flag mask check, and finally fall back to the slow path.

Fixes: 290408d4 ("hugetlb: hugepage migration core")
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Rik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 044f0f03 upstream.

When about to run the guest, deliver guest interrupts after disabling
host interrupts. This should prevent an hrtimer interrupt from being
handled after delivering guest interrupts, and therefore not delivering
the guest timer interrupt until after the next guest exit.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: Sanjay Lal <sanjayl@kymasys.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6ffa30d3 upstream.

Bruce reported seeing this warning pop when mounting using v4.1:

     ------------[ cut here ]------------
     WARNING: CPU: 1 PID: 1121 at kernel/sched/core.c:7300 __might_sleep+0xbd/0xd0()
    do not call blocking ops when !TASK_RUNNING; state=1 set at [<ffffffff810ff58f>] prepare_to_wait+0x2f/0x90
    Modules linked in: rpcsec_gss_krb5 auth_rpcgss nfsv4 dns_resolver nfs lockd grace sunrpc fscache ip6t_rpfilter ip6t_REJECT nf_reject_ipv6 xt_conntrack ebtable_nat ebtable_broute bridge stp llc ebtable_filter ebtables ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security iptable_raw snd_hda_codec_generic snd_hda_intel snd_hda_controller snd_hda_codec snd_hwdep snd_pcm snd_timer ppdev joydev snd virtio_console virtio_balloon pcspkr serio_raw parport_pc parport pvpanic floppy soundcore i2c_piix4 virtio_blk virtio_net qxl drm_kms_helper ttm drm virtio_pci virtio_ring ata_generic virtio pata_acpi
    CPU: 1 PID: 1121 Comm: nfsv4.1-svc Not tainted 3.19.0-rc4+ #25
    Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140709_153950- 04/01/2014
     0000000000000000 000000004e5e3f73 ffff8800b998fb48 ffffffff8186ac78
     0000000000000000 ffff8800b998fba0 ffff8800b998fb88 ffffffff810ac9da
     ffff8800b998fb68 ffffffff81c923e7 00000000000004d9 0000000000000000
    Call Trace:
     [<ffffffff8186ac78>] dump_stack+0x4c/0x65
     [<ffffffff810ac9da>] warn_slowpath_common+0x8a/0xc0
     [<ffffffff810aca65>] warn_slowpath_fmt+0x55/0x70
     [<ffffffff810ff58f>] ? prepare_to_wait+0x2f/0x90
     [<ffffffff810ff58f>] ? prepare_to_wait+0x2f/0x90
     [<ffffffff810dd2ad>] __might_sleep+0xbd/0xd0
     [<ffffffff8124c973>] kmem_cache_alloc_trace+0x243/0x430
     [<ffffffff810d941e>] ? groups_alloc+0x3e/0x130
     [<ffffffff810d941e>] groups_alloc+0x3e/0x130
     [<ffffffffa0301b1e>] svcauth_unix_accept+0x16e/0x290 [sunrpc]
     [<ffffffffa0300571>] svc_authenticate+0xe1/0xf0 [sunrpc]
     [<ffffffffa02fc564>] svc_process_common+0x244/0x6a0 [sunrpc]
     [<ffffffffa02fd044>] bc_svc_process+0x1c4/0x260 [sunrpc]
     [<ffffffffa03d5478>] nfs41_callback_svc+0x128/0x1f0 [nfsv4]
     [<ffffffff810ff970>] ? wait_woken+0xc0/0xc0
     [<ffffffffa03d5350>] ? nfs4_callback_svc+0x60/0x60 [nfsv4]
     [<ffffffff810d45bf>] kthread+0x11f/0x140
     [<ffffffff810ea815>] ? local_clock+0x15/0x30
     [<ffffffff810d44a0>] ? kthread_create_on_node+0x250/0x250
     [<ffffffff81874bfc>] ret_from_fork+0x7c/0xb0
     [<ffffffff810d44a0>] ? kthread_create_on_node+0x250/0x250
    ---[ end trace 675220a11e30f4f2 ]---

nfs41_callback_svc does most of its work while in TASK_INTERRUPTIBLE,
which is just wrong. Fix that by finishing the wait immediately if we've
found that the list has something on it.

Also, we don't expect this kthread to accept signals, so we should be
using a TASK_UNINTERRUPTIBLE sleep instead. That however, opens us up
hung task warnings from the watchdog, so have the schedule_timeout
wake up every 60s if there's no callback activity.
Reported-by: "J. Bruce Fields" <bfields@fieldses.org>
Signed-off-by: Jeff Layton <jlayton@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 14460dba upstream.

Current code checks "clk_delay_cycles > 0" to know whether the optional
"mrvl,clk_delay_cycles" is set or not. But of_property_read_u32() doesn't
touch clk_delay_cycles if the property is not set. And type of
clk_delay_cycles is u32, so we may always set pdata->clk_delay_cycles as a
random value.

This patch fix this problem by check the return value of of_property_read_u32()
to know whether the optional clk-delay-cycles is set or not.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 7818b0aa upstream.

Inspection shows that newlines are missing from several kernel messages
in em28xx-audio.  Fix these.

Fixes: 1b3fd2d3 ("[media] em28xx-audio: don't hardcode audio URB calculus")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 0418ca60 upstream.

The lockdep splat addressed in a previous commit revealed that at
least one message in em28xx-input.c was missing a new line:

em28178 #0: Closing input extensionINFO: trying to register non-static key.

Further inspection shows several other messages also miss a new line.
These will be fixed in a subsequent patch.

Fixes: aa929ad7 ("[media] em28xx: print a message at disconnect")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit c2ced171 upstream.

Update driver "mask_interrupts" before enable/disable hardware interrupt
in order to avoid missing interrupts because of "mask_interrupts" still
set to 1 and hardware interrupts are enabled.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Chaitra Basappa <chaitra.basappa@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit faeed51b upstream.

enable_irq_wakeup returns 0 in case it correctly enabled the IRQ to
generate the wakeup event (and thus resume should call disable_irq_wake).
Currently gpio-charger driver has this logic inverted. Correct that thus
correcting enable/disable_irq_wake() calls balance.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 478913fd upstream.

The driver mismatched 'num_supplicants' with 'num_supplies' of
power_supply structure.

It provided list of supplicants (power_supply.supplied_to) but did
not set the number of supplicants. Instead it set the num_supplies which
is used when iterating over number of supplies (power_supply.supplied_from).

As a result the list of supplicants was ignored by core because its size
was 0.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: d7bf353f ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 24727b45 upstream.

Driver forgot to unregister power supply if request_threaded_irq()
failed in probe(). In such case the memory associated with power supply
leaked.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: a830d28b ("power_supply: Enable battery-charger for 88pm860x")
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 7eb71e03 upstream.

It turns out it's possible to get __remove_osd() called twice on the
same OSD.  That doesn't sit well with rb_erase() - depending on the
shape of the tree we can get a NULL dereference, a soft lockup or
a random crash at some point in the future as we end up touching freed
memory.  One scenario that I was able to reproduce is as follows:

            <osd3 is idle, on the osd lru list>
<con reset - osd3>
con_fault_finish()
  osd_reset()
                              <osdmap - osd3 down>
                              ceph_osdc_handle_map()
                                <takes map_sem>
                                kick_requests()
                                  <takes request_mutex>
                                  reset_changed_osds()
                                    __reset_osd()
                                      __remove_osd()
                                  <releases request_mutex>
                                <releases map_sem>
    <takes map_sem>
    <takes request_mutex>
    __kick_osd_requests()
      __reset_osd()
        __remove_osd() <-- !!!

A case can be made that osd refcounting is imperfect and reworking it
would be a proper resolution, but for now Sage and I decided to fix
this by adding a safe guard around __remove_osd().

Fixes: http://tracker.ceph.com/issues/8087

Cc: Sage Weil <sage@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit cc9f1f51 upstream.

No reason to use BUG_ON for osd request list assertions.
Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 7c6e6fc5 upstream.

It is important that both regular and lingering requests lists are
empty when the OSD is removed.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3ce465e0 upstream.

Export the _save_fp asm function used by the lose_fpu(1) macro to GPL
modules so that KVM can make use of it when it is built as a module.

This fixes the following build error when CONFIG_KVM=m due to commit
f798217d ("KVM: MIPS: Don't leak FPU/DSP to guest"):

ERROR: "_save_fp" [arch/mips/kvm/kvm.ko] undefined!
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Fixes: f798217d (KVM: MIPS: Don't leak FPU/DSP to guest)
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9260/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
[james.hogan@imgtec.com: Only export when CPU_R4K_FPU=y prior to v3.16,
 so as not to break the Octeon build which excludes FPU support. KVM
 depends on MIPS32r2 anyway.]
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f0153c3d upstream.

RME RayDAT and AIO use a fixed buffer size of 16384 samples. With period
sizes of 32-4096, this translates to 4-512 periods.

The older RME cards have a variable buffer size but require exactly two
periods.

This patch enforces nperiods=2 on those cards.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e4940626 upstream.

The problem here is that we check:

	if (dev >= SNDRV_CARDS)

Then we increment "dev".

       if (!joystick_port[dev++])

Then we use it as an offset into a array with SNDRV_CARDS elements.

	if (!request_region(joystick_port[dev], 8, "Riptide gameport")) {

This has 3 effects:
1) If you use the module option to specify the joystick port then it has
   to be shifted one space over.
2) The wrong error message will be printed on failure if you have over
   32 cards.
3) Static checkers will correctly complain that are off by one.

Fixes: db1005ec ('ALSA: riptide - Fix joystick resource handling')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 15e1ce33 upstream.

A quirk of some older firmwares that report endpoint pipe type as PIPE_BULK
but the endpoint otheriwse functions as interrupt.

Check if usb_endpoint_type is USB_ENDPOINT_XFER_BULK and set as usb_rcvbulkpipe.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 72978b2f upstream.

Commit 61a734d3 ("xen/manage: Always freeze/thaw processes when
suspend/resuming") ensured that userspace processes were always frozen
before suspending to reduce interaction issues when resuming devices.
However, freeze_processes() does not freeze kernel threads.  Freeze
kernel threads as well to prevent deadlocks with the khubd thread when
resuming devices.

This is what native suspend and resume does.

Example deadlock:
[ 7279.648010]  [<ffffffff81446bde>] ? xen_poll_irq_timeout+0x3e/0x50
[ 7279.648010]  [<ffffffff81448d60>] xen_poll_irq+0x10/0x20
[ 7279.648010]  [<ffffffff81011723>] xen_lock_spinning+0xb3/0x120
[ 7279.648010]  [<ffffffff810115d1>] __raw_callee_save_xen_lock_spinning+0x11/0x20
[ 7279.648010]  [<ffffffff815620b6>] ? usb_control_msg+0xe6/0x120
[ 7279.648010]  [<ffffffff81747e50>] ? _raw_spin_lock_irq+0x50/0x60
[ 7279.648010]  [<ffffffff8174522c>] wait_for_completion+0xac/0x160
[ 7279.648010]  [<ffffffff8109c520>] ? try_to_wake_up+0x2c0/0x2c0
[ 7279.648010]  [<ffffffff814b60f2>] dpm_wait+0x32/0x40
[ 7279.648010]  [<ffffffff814b6eb0>] device_resume+0x90/0x210
[ 7279.648010]  [<ffffffff814b7d71>] dpm_resume+0x121/0x250
[ 7279.648010]  [<ffffffff8144c570>] ? xenbus_dev_request_and_reply+0xc0/0xc0
[ 7279.648010]  [<ffffffff814b80d5>] dpm_resume_end+0x15/0x30
[ 7279.648010]  [<ffffffff81449fba>] do_suspend+0x10a/0x200
[ 7279.648010]  [<ffffffff8144a2f0>] ? xen_pre_suspend+0x20/0x20
[ 7279.648010]  [<ffffffff8144a1d0>] shutdown_handler+0x120/0x150
[ 7279.648010]  [<ffffffff8144c60f>] xenwatch_thread+0x9f/0x160
[ 7279.648010]  [<ffffffff810ac510>] ? finish_wait+0x80/0x80
[ 7279.648010]  [<ffffffff8108d189>] kthread+0xc9/0xe0
[ 7279.648010]  [<ffffffff8108d0c0>] ? flush_kthread_worker+0x80/0x80
[ 7279.648010]  [<ffffffff8175087c>] ret_from_fork+0x7c/0xb0
[ 7279.648010]  [<ffffffff8108d0c0>] ? flush_kthread_worker+0x80/0x80

[ 7441.216287] INFO: task khubd:89 blocked for more than 120 seconds.
[ 7441.219457]       Tainted: G            X 3.13.11-ckt12.kz #1
[ 7441.222176] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 7441.225827] khubd           D ffff88003f433440     0    89      2 0x00000000
[ 7441.229258]  ffff88003ceb9b98 0000000000000046 ffff88003ce83000 0000000000013440
[ 7441.232959]  ffff88003ceb9fd8 0000000000013440 ffff88003cd13000 ffff88003ce83000
[ 7441.236658]  0000000000000286 ffff88003d3e0000 ffff88003ceb9bd0 00000001001aa01e
[ 7441.240415] Call Trace:
[ 7441.241614]  [<ffffffff817442f9>] schedule+0x29/0x70
[ 7441.243930]  [<ffffffff81743406>] schedule_timeout+0x166/0x2c0
[ 7441.246681]  [<ffffffff81075b80>] ? call_timer_fn+0x110/0x110
[ 7441.249339]  [<ffffffff8174357e>] schedule_timeout_uninterruptible+0x1e/0x20
[ 7441.252644]  [<ffffffff81077710>] msleep+0x20/0x30
[ 7441.254812]  [<ffffffff81555f00>] hub_port_reset+0xf0/0x580
[ 7441.257400]  [<ffffffff81558465>] hub_port_init+0x75/0xb40
[ 7441.259981]  [<ffffffff814bb3c9>] ? update_autosuspend+0x39/0x60
[ 7441.262817]  [<ffffffff814bb4f0>] ? pm_runtime_set_autosuspend_delay+0x50/0xa0
[ 7441.266212]  [<ffffffff8155a64a>] hub_thread+0x71a/0x1750
[ 7441.268728]  [<ffffffff810ac510>] ? finish_wait+0x80/0x80
[ 7441.271272]  [<ffffffff81559f30>] ? usb_port_resume+0x670/0x670
[ 7441.274067]  [<ffffffff8108d189>] kthread+0xc9/0xe0
[ 7441.276305]  [<ffffffff8108d0c0>] ? flush_kthread_worker+0x80/0x80
[ 7441.279131]  [<ffffffff8175087c>] ret_from_fork+0x7c/0xb0
[ 7441.281659]  [<ffffffff8108d0c0>] ? flush_kthread_worker+0x80/0x80
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 61882b63 upstream.

The two functions s3c2416_cpufreq_driver_init and s3c_cpufreq_register
are marked init but are called from a context that might be run after
the __init sections are discarded, as the compiler points out:

WARNING: vmlinux.o(.data+0x1ad9dc): Section mismatch in reference from the variable s3c2416_cpufreq_driver to the function .init.text:s3c2416_cpufreq_driver_init()
WARNING: drivers/built-in.o(.text+0x35b5dc): Section mismatch in reference from the function s3c2410a_cpufreq_add() to the function .init.text:s3c_cpufreq_register()

This removes the __init markings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d4d4eda2 upstream.

On Dell Latitude C600 laptop with Pentium 3 850MHz processor, the
speedstep-smi driver sometimes loads and sometimes doesn't load with
"change to state X failed" message.

The hardware sometimes refuses to change frequency and in this case, we
need to retry later. I found out that we need to enable interrupts while
waiting. When we enable interrupts, the hardware blockage that prevents
frequency transition resolves and the transition is possible. With
disabled interrupts, the blockage doesn't resolve (no matter how long do
we wait). The exact reasons for this hardware behavior are unknown.

This patch enables interrupts in the function speedstep_set_state that can
be called with disabled interrupts. However, this function is called with
disabled interrupts only from speedstep_get_freqs, so it shouldn't cause
any problem.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6ffae8c0 upstream.

In __cpufreq_remove_dev_finish(), per-cpu 'cpufreq_cpu_data' needs
to be cleared before calling kobject_put(&policy->kobj) and under
cpufreq_driver_lock. Otherwise, if someone else calls cpufreq_cpu_get()
in parallel with it, they can obtain a non-NULL policy from that after
kobject_put(&policy->kobj) was executed.

Consider this case:

Thread A				Thread B
cpufreq_cpu_get()
  acquire cpufreq_driver_lock
  read-per-cpu cpufreq_cpu_data
					kobject_put(&policy->kobj);
  kobject_get(&policy->kobj);
					...
					per_cpu(&cpufreq_cpu_data, cpu) = NULL

And this will result in a warning like this one:

 ------------[ cut here ]------------
 WARNING: CPU: 0 PID: 4 at include/linux/kref.h:47
 kobject_get+0x41/0x50()
 Modules linked in: acpi_cpufreq(+) nfsd auth_rpcgss nfs_acl
 lockd grace sunrpc xfs libcrc32c sd_mod ixgbe igb mdio ahci hwmon
 ...
 Call Trace:
  [<ffffffff81661b14>] dump_stack+0x46/0x58
  [<ffffffff81072b61>] warn_slowpath_common+0x81/0xa0
  [<ffffffff81072c7a>] warn_slowpath_null+0x1a/0x20
  [<ffffffff812e16d1>] kobject_get+0x41/0x50
  [<ffffffff815262a5>] cpufreq_cpu_get+0x75/0xc0
  [<ffffffff81527c3e>] cpufreq_update_policy+0x2e/0x1f0
  [<ffffffff810b8cb2>] ? up+0x32/0x50
  [<ffffffff81381aa9>] ? acpi_ns_get_node+0xcb/0xf2
  [<ffffffff81381efd>] ? acpi_evaluate_object+0x22c/0x252
  [<ffffffff813824f6>] ? acpi_get_handle+0x95/0xc0
  [<ffffffff81360967>] ? acpi_has_method+0x25/0x40
  [<ffffffff81391e08>] acpi_processor_ppc_has_changed+0x77/0x82
  [<ffffffff81089566>] ? move_linked_works+0x66/0x90
  [<ffffffff8138e8ed>] acpi_processor_notify+0x58/0xe7
  [<ffffffff8137410c>] acpi_ev_notify_dispatch+0x44/0x5c
  [<ffffffff8135f293>] acpi_os_execute_deferred+0x15/0x22
  [<ffffffff8108c910>] process_one_work+0x160/0x410
  [<ffffffff8108d05b>] worker_thread+0x11b/0x520
  [<ffffffff8108cf40>] ? rescuer_thread+0x380/0x380
  [<ffffffff81092421>] kthread+0xe1/0x100
  [<ffffffff81092340>] ? kthread_create_on_node+0x1b0/0x1b0
  [<ffffffff81669ebc>] ret_from_fork+0x7c/0xb0
  [<ffffffff81092340>] ? kthread_create_on_node+0x1b0/0x1b0
 ---[ end trace 89e66eb9795efdf7 ]---

The actual code flow is as follows:

 Thread A: Workqueue: kacpi_notify

 acpi_processor_notify()
   acpi_processor_ppc_has_changed()
         cpufreq_update_policy()
           cpufreq_cpu_get()
             kobject_get()

 Thread B: xenbus_thread()

 xenbus_thread()
   msg->u.watch.handle->callback()
     handle_vcpu_hotplug_event()
       vcpu_hotplug()
         cpu_down()
           __cpu_notify(CPU_POST_DEAD..)
             cpufreq_cpu_callback()
               __cpufreq_remove_dev_finish()
                 cpufreq_policy_put_kobj()
                   kobject_put()

cpufreq_cpu_get() gets the policy from per-cpu variable cpufreq_cpu_data
under cpufreq_driver_lock, and once it gets a valid policy it expects it
to not be freed until cpufreq_cpu_put() is called.

But the race happens when another thread puts the kobject first and updates
cpufreq_cpu_data before or later. And so the first thread gets a valid policy
structure and before it does kobject_get() on it, the second one has already
done kobject_put().

Fix this by setting cpufreq_cpu_data to NULL before putting the kobject and that
too under locks.
Reported-by: Ethan Zhao <ethan.zhao@oracle.com>
Reported-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 16b036af upstream.

If the image size would ever read as 0, pci_get_rom_size() could keep
processing the same image over and over again.  Exit the loop if we ever
read a length of zero.

This fixes a soft lockup on boot when the radeon driver calls
pci_get_rom_size() on an AMD Radeon R7 250X PCIe discrete graphics card.

[bhelgaas: changelog, reference]
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1386973Reported-by: Federico <federicotg@gmail.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 145b3fe5 upstream.

Some implementations of modprobe fail to load the driver for a PCI device
automatically because the "interface" part of the modalias from the kernel
is lowercase, and the modalias from file2alias is uppercase.

The "interface" is the low-order byte of the Class Code, defined in PCI
r3.0, Appendix D.  Most interface types defined in the spec do not use
alpha characters, so they won't be affected.  For example, 00h, 01h, 10h,
20h, etc. are unaffected.

Print the "interface" byte of the Class Code in uppercase hex, as we
already do for the Vendor ID, Device ID, Class, etc.

Commit 89ec3dcf ("PCI: Generate uppercase hex for modalias interface
class") fixed only half of the problem.  Some udev implementations rely on
the uevent file and not the modalias file.

Fixes: d1ded203 ("PCI: add MODALIAS to hotplug event for pci devices")
Fixes: 89ec3dcf ("PCI: Generate uppercase hex for modalias interface class")
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6d00f37e upstream.

d1c7e29e (HID: i2c-hid: prevent buffer overflow in early IRQ)
changed hid_get_input() to read ihid->bufsize bytes, which can be
more than wMaxInputLength. This is the case with the Dell XPS 13
9343, and it is causing events to be missed. In some cases the
missed events are releases, which can cause the cursor to jump or
freeze, among other problems. Limit the number of bytes read to
min(wMaxInputLength, ihid->bufsize) to prevent such problems.

Fixes: d1c7e29e "HID: i2c-hid: prevent buffer overflow in early IRQ"
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5523d11c upstream.

We don't really need to use different mac colors when adding mac
contexts, because they're not used anywhere.  In fact, the firmware
doesn't accept 255 as a valid color, so we get into a SYSASSERT 0x3401
when we reach that.

Remove the color increment to use always zero and avoid reaching 255.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit fd66fc1c upstream.

When iwl_mvm_power_update_mac() is called, we have already added the
mac context, so if this call fails we should remove the mac.

Fixes: commit e5e7aa8e ('iwlwifi: mvm: refactor power code')
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 2cee4762 upstream.

These are coming from the FW and are used to access arrays.
Bad values can cause an out of bounds access so discard
such ba_notifs and warn.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit cd8f4384 upstream.

The base address of the scheduler in the device's memory
(SRAM) comes from two different sources. The periphery
register and the alive notification from the firmware.
We have a check in iwl_pcie_tx_start that ensures that
they are the same.
When we resume from WoWLAN, the firmware may have crashed
for whatever reason. In that case, the whole device may be
reset which means that the periphery register will hold a
meaningless value. When we come to compare
trans_pcie->scd_base_addr (which really holds the value we
had when we loaded the WoWLAN firmware upon suspend) and
the current value of the register, we don't see a match
unsurprisingly.
Trick the check to avoid a loud yet harmless WARN.
Note that when the WoWLAN has crashed, we will see that
in iwl_trans_pcie_d3_resume which will let the op_mode
know. Once the op_mode is informed that the WowLAN firmware
has crashed, it can't do much besides resetting the whole
device.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6ee8e25f upstream.

Commit e9fd702a ("audit: convert audit watches to use fsnotify
instead of inotify") broke handling of renames in audit.  Audit code
wants to update inode number of an inode corresponding to watched name
in a directory.  When something gets renamed into a directory to a
watched name, inotify previously passed moved inode to audit code
however new fsnotify code passes directory inode where the change
happened.  That confuses audit and it starts watching parent directory
instead of a file in a directory.

This can be observed for example by doing:

  cd /tmp
  touch foo bar
  auditctl -w /tmp/foo
  touch foo
  mv bar foo
  touch foo

In audit log we see events like:

  type=CONFIG_CHANGE msg=audit(1423563584.155:90): auid=1000 ses=2 op="updated rules" path="/tmp/foo" key=(null) list=4 res=1
  ...
  type=PATH msg=audit(1423563584.155:91): item=2 name="bar" inode=1046884 dev=08:0 2 mode=0100644 ouid=0 ogid=0 rdev=00:00 nametype=DELETE
  type=PATH msg=audit(1423563584.155:91): item=3 name="foo" inode=1046842 dev=08:0 2 mode=0100644 ouid=0 ogid=0 rdev=00:00 nametype=DELETE
  type=PATH msg=audit(1423563584.155:91): item=4 name="foo" inode=1046884 dev=08:0 2 mode=0100644 ouid=0 ogid=0 rdev=00:00 nametype=CREATE
  ...

and that's it - we see event for the first touch after creating the
audit rule, we see events for rename but we don't see any event for the
last touch.  However we start seeing events for unrelated stuff
happening in /tmp.

Fix the problem by passing moved inode as data in the FS_MOVED_FROM and
FS_MOVED_TO events instead of the directory where the change happens.
This doesn't introduce any new problems because noone besides
audit_watch.c cares about the passed value:

  fs/notify/fanotify/fanotify.c cares only about FSNOTIFY_EVENT_PATH events.
  fs/notify/dnotify/dnotify.c doesn't care about passed 'data' value at all.
  fs/notify/inotify/inotify_fsnotify.c uses 'data' only for FSNOTIFY_EVENT_PATH.
  kernel/audit_tree.c doesn't care about passed 'data' at all.
  kernel/audit_watch.c expects moved inode as 'data'.

Fixes: e9fd702a ("audit: convert audit watches to use fsnotify instead of inotify")
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Paul Moore <paul@paul-moore.com>
Cc: Eric Paris <eparis@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3443a3bc upstream.

When the superblock is modified in a transaction, the commonly
modified fields are not actually copied to the superblock buffer to
avoid the buffer lock becoming a serialisation point. However, there
are some other operations that modify the superblock fields within
the transaction that don't directly log to the superblock but rely
on the changes to be applied during the transaction commit (to
minimise the buffer lock hold time).

When we do this, we fail to mark the buffer log item as being a
superblock buffer and that can lead to the buffer not being marked
with the corect type in the log and hence causing recovery issues.
Fix it by setting the type correctly, similar to xfs_mod_sb()...
Tested-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f19b872b upstream.

This leads to log recovery throwing errors like:

XFS (md0): Mounting V5 Filesystem
XFS (md0): Starting recovery (logdev: internal)
XFS (md0): Unknown buffer type 0!
XFS (md0): _xfs_buf_ioapply: no ops on block 0xaea8802/0x1
ffff8800ffc53800: 58 41 47 49 .....

Which is the AGI buffer magic number.

Ensure that we set the type appropriately in both unlink list
addition and removal.
Tested-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 0d612fb5 upstream.

Jan Kara reported that log recovery was finding buffers with invalid
types in them. This should not happen, and indicates a bug in the
logging of buffers. To catch this, add asserts to the buffer
formatting code to ensure that the buffer type is in range when the
transaction is committed.

We don't set a type on buffers being marked stale - they are not
going to get replayed, the format item exists only for recovery to
be able to prevent replay of the buffer, so the type does not
matter. Hence that needs special casing here.
Reported-by: Jan Kara <jack@suse.cz>
Tested-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit c561a575 upstream.

BugLink: https://bugs.launchpad.net/bugs/1400215

ath3k devices fail to load firmwares on xHCI buses, but work well on
EHCI, this might be a compatibility issue between xHCI and ath3k chips.
As my testing result, those chips will work on xHCI buses again with
this patch.

This workaround is from Qualcomm, they also did some workarounds in
Windows driver.
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a8f29e89 upstream.

Userspace expects to see a long space before the first pulse is sent on
the lirc device.  Currently, if a long time has passed and a new packet
is started, the lirc codec just returns and doesn't send anything.  This
makes lircd ignore many perfectly valid signals unless they are sent in
quick sucession.  When a reset event is delivered, we cannot know
anything about the duration of the space.  But it should be safe to
assume it has been a long time and we just set the duration to maximum.
Signed-off-by: Austin Lund <austin.lund@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit cfbf654e ]

When making use of RFC5061, section 4.2.4. for setting the primary IP
address, we're passing a wrong parameter header to param_type2af(),
resulting always in NULL being returned.

At this point, param.p points to a sctp_addip_param struct, containing
a sctp_paramhdr (type = 0xc004, length = var), and crr_id as a correlation
id. Followed by that, as also presented in RFC5061 section 4.2.4., comes
the actual sctp_addr_param, which also contains a sctp_paramhdr, but
this time with the correct type SCTP_PARAM_IPV{4,6}_ADDRESS that
param_type2af() can make use of. Since we already hold a pointer to
addr_param from previous line, just reuse it for param_type2af().

Fixes: d6de3097 ("[SCTP]: Add the handling of "Set Primary IP Address" parameter to INIT")
Signed-off-by: Saran Maruti Ramanara <saran.neti@telus.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit e2a4800e ]

When we've run out of space in the output buffer to store more data, we
will call zlib_deflate with a NULL output buffer until we've consumed
remaining input.

When this happens, olen contains the size the output buffer would have
consumed iff we'd have had enough room.

This can later cause skb_over_panic when ppp_generic skb_put()s
the returned length.
Reported-by: Iain Douglas <centos@1n6.org.uk>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit bdbbb852 ]

In commit be9f4a44 ("ipv4: tcp: remove per net tcp_sock")
I tried to address contention on a socket lock, but the solution
I chose was horrible :

commit 3a7c384f ("ipv4: tcp: unicast_sock should not land outside
of TCP stack") addressed a selinux regression.

commit 0980e56e ("ipv4: tcp: set unicast_sock uc_ttl to -1")
took care of another regression.

commit b5ec8eea ("ipv4: fix ip_send_skb()") fixed another regression.

commit 811230cd ("tcp: ipv4: initialize unicast_sock sk_pacing_rate")
was another shot in the dark.

Really, just use a proper socket per cpu, and remove the skb_orphan()
call, to re-enable flow control.

This solves a serious problem with FQ packet scheduler when used in
hostile environments, as we do not want to allocate a flow structure
for every RST packet sent in response to a spoofed packet.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>