This change creates a new module, ath.ko, which includes code that can
be shared between ath5k, ath9k and ar9170. For now, extract most of the ath9k
regulatory code so it can also be used in ath5k.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

All regulatory information is encapsulated by the ath9k_regulatory
struct, so we can now change all the callers to take that directly
instead of struct ath_hw.  This in turn will enable us to move the
regulatory functions to common code also used by ath5k, since both
can use this regulatory struct.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Until ath5k and ath9k share common channel structures, they will have
to implement their own get_ctl() function.  Split out the portion that
only relies on the current band and reg domain so that it can be common
code.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The STATUS_ALIVE value cannot be used because it is cleared when
interface is brought down and will not be set if rfkill is enabled when
interface is started again. The interface can thus not be brought up if
rfkill was enabled before stopping the interface and disabled after
starting the interface.

Change the test to use priv->is_open instead, this will be set when
interface is started whether rfkill is enabled or not.

Thanks to Helmut Schaa for the suggested fix.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Convert scan function to cfg80211. Unlike old scan code new code
waits 1 sec before getting scan data from device and passing
forward to cfg80211.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Change quality level scale to match cfg80211 CFG80211_SIGNAL_TYPE_UNSPEC.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Added cfg80211_inform_bss() for full-mac devices to use.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: John W. Linville <linville@tuxdriver.com>
[edit: made rndis_change_virtual_intf static]
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds beacon filtering support to p54.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch hopefully finishes the SoftLED code:
- It adds two more LEDs (rx and radio).
  (the FW claims it can support up to 16 LEDs,
   but I doubt that any vendor put more than 4 on a board)
- update the LEDs in a _delayed_ workqueue.
  No one reported any more crashes.
  (see: "PATCH] p54: fix race condition in memory management")
  So we can stop burning the mm code.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch rearrange and regroups most elements in p54_common.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Update the MAINTAINERS entry for PS3 NETWORK SUPPORT.

CC: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Claiming every available 5 ghz channel has a couple of negative
side-effects: scanning takes a long time, and the channel list
overflows the available buffer space for netlink commands,
resulting in:

    $ iw phy phy0 info
    command failed: No buffer space available (-105)

This patch adds a modparam so people who want to see all the channels
can do so by passing all_channels=1.  By default users will see a
smaller list of channels.  This also halves scan time, from 10 seconds
down to less than 5 when using world regulatory.

Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Reported-by: Simon Farnsworth <simon@farnz.org.uk>
Tested-By: Simon Farnsworth <simon@farnz.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It really belongs into that file since it is only relevant
for managed mode. Move 1:1, not even whitespace changes,
but make it static and remove from header file.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes a bug in checking for HT40 mode.
The STA's mode can be determined from the cached HT capabilities,
use that and remove the redundant variable 'rc_phy_mode'.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The number of streams supported by a STA can be determined
directly from the HT capabilities. Remove the redundant
variable storing the stream cap.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch cleans up the ISR, removing a unnecessary do..while
loop, and waking up the chip before getting the pending
interrupts.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Handle aggregation params only when aggregation is
supported.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Also fix a small typo.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

These are unnecessary constructs in a function.
This patch removes these from both RX and TX init
routines.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We never handle TIM, TIM_TIMER is used instead.
Remove this and the unnecessary swBeaconProcess variable.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Creation of the root debugfs file could have failed
for some reason, check properly before proceeding in this
case.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

struct aggr_rifs_param and ath_tx_stat are not used anywhere.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Using a u32 to store a single flag is overkill.
Use a bool to store whether the buffer is stale or not.
Also, use u8 instead of u32 to store the buffer type.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Change the void pointer to struct sk_buff and access
bf_mpdu directly, removing all casts in the process.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The state is already stored in ath9k_ops_config, so remove
the duplicate variable in ath_hw.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This routine always return true, checking for false
in the return value is invalid. Fix this.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Clean debug messages to use appropriate levels,
remove useless messages, and trim the number of
debug levels.
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We get the valid chainmasks on HW attach, checking
it again during reset is redundant. This patch removes the check.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch removes unused HW capability flags and
HW operation variables, and a chainmask flag that
we don't use anywhere.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For chipsets supporting autosleep feature, there is no need to abort
Rx engine since they are capable of automatically going back to sleep
after receiving a packet.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Auto-depend on HW_RANDOM, rather than "select"ing it.
This way the user has the choice to enable or disable HWRNG support.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00link_reset_qual() is not declared in a header,
and is only internally used within rt2x00link.c.
It should be declared as static.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

pci_dev->irq and pci_name(pci_dev) access should be limited
to rt2x00pci only. This is more generic and allows a rt2x00 pci
driver to be controlled as PCI device but also as platform driver
(needed for rt2800pci SoC support).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes a locking problem which freezes the network core.

The deadlock goes as follows:
- ar9170_op_stop - is called
1. change the state to IDLE
2. > take the MUTEX <
3. cancel_SYNC all pending work, which means
    "block until a work_struct's callback has terminated"
=>  if filter_config_work was queued it tries to get the MUTEX,
       before checking the device state...
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

AR5K_PHY_PLL_40MHZ_5413 should not be ORed with AR5K_PHY_MODE_RAD_RF5112
for 5 GHz channels.

The incorrect PLL value breaks scanning in the countries where 5 GHz
channels are allowed.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This has been the case really, we just forgot to update it.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>