The SH7757's GETHER has TSU registers. So, this patch adds the value
of ".tsu = 1" in the sh_eth_cpu_data.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On the SFC9000 family, each port has 1024 Virtual Interfaces (VIs),
each with an RX queue, a TX queue, an event queue and a mailbox
register.  These may be assigned to up to 127 SR-IOV virtual functions
per port, with up to 64 VIs per VF.

We allocate an extra channel (IRQ and event queue only) to receive
requests from VF drivers.

There is a per-port limit of 4 concurrent RX queue flushes, and queue
flushes may be initiated by the MC in response to a Function Level
Reset (FLR) of a VF.  Therefore, when SR-IOV is in use, we submit all
flush requests via the MC.

The RSS indirection table is shared with VFs, so the number of RX
queues used in the PF is limited to the number of VIs per VF.

This is almost entirely the work of Steve Hodgson, formerly
shodgson@solarflare.com.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

Each port has a block of 64-bit SRAM that is divided between buffer
table and descriptor cache regions at initialisation time.  Currently
we use a fixed allocation, but it needs to be changed to support
larger numbers of queues.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

This lets us identify the NIC affected in case of failure, and
will be necessary to adjust for SR-IOV constraints.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

Abstract some of the channel operations to allow for 'extra'
channels that do not have RX or TX queues.

- Try to assign a channel to each extra channel type that is enabled
  for the NIC, but gracefully degrade if we can't allocate sufficient
  MSI-X vectors
- Allow each extra channel type to generate its own channel name
- Allow channel types to disable reallocation and reinitialisation
  of their channels
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

The TX DMA engine issues upstream read requests when there is room in
the TX FIFO for the completion. However, the fetches for the rest of
the packet might be delayed by any back pressure.  Since a flush must
wait for an EOP, the entire flush may be delayed by back pressure.

Mitigate this by disabling flow control before the flushes are
started.  Since PF and VF flushes run in parallel introduce
fc_disable, a reference count of the number of flushes outstanding.

The same principle could be applied to Falcon, but that
would bring with it its own testing.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

For SR-IOV we will need to send events to event queues that belong to
VFs serviced by other drivers.  Change the parameters of
efx_generate_event() to allow this and declare it extern.

While we're at it, remove the existing declaration under the wrong
name efx_nic_generate_event().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

When SR-IOV is enabled we may receive FLR (Function-Level Reset)
events, associated queue flush events and requests from VF drivers at
any time.  Therefore we need to keep event queues and interrupts
enabled whenever possible.

Currently we stop interrupt-driven event processing before flushing RX
and TX queues; efx_nic_flush_queues() then polls event queues for
flush events and discards any others it finds.  Change it to work with
the regular event handling functions.

Currently efx_start_channel() fills RX queues synchronously when a
device is brought up.  This could now race with NAPI, so change it to
send fill events.

This was almost entirely written by Steve Hodgson, formerly
shodgson@solarflare.com.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

This makes it harder to accidentally send such events to TX-only
channels.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

The RMFT_DEST_MAC and TMFT_SRC_MAC register fields were previously
documented as 44 bits wide, whereas a MAC address has 48 bits.
Thankfully the hardware uses the correct width and the driver has
used separate definitions that divide each of these into 32-bit and
16-bit fields.

Fix the initial definitions for these fields and rewrite the latter
definitions to use them.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

On Siena each TX queue can be configured to send only packets for
which there is a TX MAC filter that matches the source MAC address,
queue ID, and optionally VID.  This will be used to implement the
'spoofchk' feature for SR-IOV virtual functions.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

On Siena all received packets that don't match a more specific filter
will match the unicast or multicast default filter.  Currently we
leave these set to the default values (RSS with base queue number of
0).  Allow them to be reconfigured to select a single RX queue.

These default filters are programmed through the FILTER_CTL register,
but we represent them internally as an additional table of size 2.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

'tbl' is always arp_tbl, so specifying it is pointless.
Signed-off-by: David S. Miller <davem@davemloft.net>

Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hi Dave,

This patch is sent in conjunction with the cxgb3 firmware update submission on linux-firmware.
(https://lkml.org/lkml/2012/2/13/27)

Cheers,
Divy

From: Divy Le Ray <divy@chelsio.com>

This patch updates the firmware version cxgb3 is requesting to 7.12.0.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove double include of linux/interrupt.h.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use eth_hw_addr_random() instead of calling random_ether_addr()
to set addr_assign_type correctly to NET_ADDR_RANDOM.

Reset the state to NET_ADDR_PERM as soon as the MAC get
changed via .ndo_set_mac_address.

v2: adapt to renamed eth_hw_addr_random()
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace usage of random_ether_addr() with eth_hw_addr_random()
to set addr_assign_type correctly to NET_ADDR_RANDOM.

Change the trivial cases.

v2: adapt to renamed eth_hw_addr_random()
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The phy FW version is stored in regular memory, no MDC-MDIO access or
any special locks are required to read it in the current implementation.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

From: Merav Sicron <meravs@broadcom.com>

Current ethtool self tests usesa large buffer on stack. This patch replaces
that array by dynamically allocated memory
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

From: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

From: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Following the changes in the ethtool source code, this patch enables
the bnx2x driver to publish the Link partner's capabilities s, when ethtool
is used on an interface which completed autoneg.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

From: Yaniv Rosner <yaniv.rosner@broadcom.com>

Several boards require an additional HW bit written in-order to enable
half duplex.
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently bnx2x statistics are reset by inner driver reload, e.g. by MTU
change. This patch fixes this issue - from now on statistics should only
be reset upon device closure.
Thanks to Michal Schmidt <mschmidt@redhat.com> for his initial patch
regarding this issue.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add unicast steering entries to resource tracker.
Do qp_detach also for these entries when VF doesn't shut down gracefully.
Otherwise there is leakage of these resources, since they are not tracked.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlx4_multicast_attach/detach() should use always MLX4_MC_STEER flag
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlx4_uc_steer_add/release() should not add MLX4_UC_STEER flag to gid.
It is added in mlx4_unicast_attach/detach().
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlx4_qp_attach/detach_common() don't use hash variable, move it to find_entry()
static find_entry() in mcg.c doesn't use steer argument
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove unnecessary field high_prios from mlx4_steer struct and initialization
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

When adding new unicast steer entry, before moving qp to state ready,
actually before calling mlx4_RST2INIT_QP_wrapper(), there were added
a lot of entries with local_qpn=0 into radix tree.
This fact impacted the get_res() function and proper functioning
of resource tracker in addition to adding trash entries into radix tree.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@melllanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>