Restructure GPIO table to fit maximum line length.

Fix mistakes found while working on OpenBMC userland configuration and
based on probing the board.

Schematic for this board is not available. Because of this the choice
was made to use a descriptive method for naming the GPIOs.

 - Push-pull outputs start with output-*
 - Open-drain outputs start with control-*
 - LED outputs start with led-*
 - Inputs start with input-*
 - Button inputs start with button-*
 - Active low signals end with *-n
Signed-off-by: Renze Nicolai <renze@rnplus.nl>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Since the ocp debug card only supports 100k, the bus is also set to 100k.
Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
[AJ: Fixed fuzz due to prior IPMB patch]
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

The PCA chip for the NVMe LEDs is wired up backwards, so correct
the device tree labels.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Add OCP debug card devicetree config
Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

A recent change to the lm25066 driver changed the name of its
regulator from vout0 to vout; device-tree users of lm25066's regulator
functionality (of which ahe50dc is the only one) thus require a
corresponding update.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Cc: Conor Dooley <conor+dt@kernel.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Due to the way i2c driver matching works (falling back to the driver's
id_table if of_match_table fails) this didn't actually cause any
misbehavior, but let's add the vendor prefixes so things actually work
the way they were intended to.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Like the more recently added ASRock BMC platforms, e3c246d4i and
romed8hm3 also have the BMC's MAC address available in the baseboard
FRU EEPROM, so let's add support for using it.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Added a device tree for IBM system1 BMC board, which uses AST2600 SoC.
Signed-off-by: Andrew Geissler <geissonator@yahoo.com>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Link: https://lore.kernel.org/r/20240125212154.4028640-3-ninad@linux.ibm.comSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Document the new compatibles used on IBM system1-bmc
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Link: https://lore.kernel.org/r/20240125212154.4028640-2-ninad@linux.ibm.comSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Enable FSI interrupt controllers for AST2600 and P10BMC hub master.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20240215220759.976998-27-eajames@linux.ibm.comSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Add:
"reset-cause-platrst", "cpu0-err-alert", "leakage-detect-alert",
"presence-post-card", "ac-power-button", "P0_I3C_APML_ALERT_L",
"irq-uv-detect-alert", "irq-hsc-alert", "cpu0-prochot-alert",
"cpu0-thermtrip-alert", "reset-cause-pcie", "pvdd11-ocp-alert"

Rename:
"power-cpu-good" to "host0-ready",
"host-ready-n" to "post-end-n
Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
Link: https://lore.kernel.org/r/20240412091600.2534693-13-peteryin.openbmc@gmail.comSigned-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Add pt5161l device in i2c bus12 and bus21.
Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
Link: https://lore.kernel.org/r/20240412091600.2534693-12-peteryin.openbmc@gmail.comSigned-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Revise max31790 and delta_brick node name.
Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
Link: https://lore.kernel.org/r/20240412091600.2534693-11-peteryin.openbmc@gmail.comSigned-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Add ltc4286 device.
Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
Link: https://lore.kernel.org/r/20240412091600.2534693-10-peteryin.openbmc@gmail.comSigned-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Add MB NIC Device
Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
Link: https://lore.kernel.org/r/20240412091600.2534693-9-peteryin.openbmc@gmail.comSigned-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Revise max31790 address from 0x30 to 0x5e
Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
Link: https://lore.kernel.org/r/20240412091600.2534693-8-peteryin.openbmc@gmail.comSigned-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Add PDB temperature sensor.
Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
Link: https://lore.kernel.org/r/20240412091600.2534693-7-peteryin.openbmc@gmail.comSigned-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Add spi-gpio for tpm device.
Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
Link: https://lore.kernel.org/r/20240412091600.2534693-6-peteryin.openbmc@gmail.comSigned-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Add a line name for cpu power good.
Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
Link: https://lore.kernel.org/r/20240412091600.2534693-5-peteryin.openbmc@gmail.comSigned-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Remove vuart to avoid port conflict with uart2
Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
Link: https://lore.kernel.org/r/20240412091600.2534693-4-peteryin.openbmc@gmail.comSigned-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Change routing to match SOL(Serial Over LAN) settings.
Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
Link: https://lore.kernel.org/r/20240412091600.2534693-3-peteryin.openbmc@gmail.comSigned-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

The same name as reset-control-smb-e1s
change to reset-control-smb-e1s-0 and reset-control-smb-e1s-0.
Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
Link: https://lore.kernel.org/r/20240412091600.2534693-2-peteryin.openbmc@gmail.comSigned-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Add the SGPIO line name that the project's function can use by the
meaningful name.
Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231212075200.983536-12-yangchen.openbmc@gmail.comSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Add the GPIO line name that the project's function can use by the
meaningful name.
Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231212075200.983536-11-yangchen.openbmc@gmail.comSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Add led-fan-fault gpio pin on the PCA9555 on the i2c bus 0.
Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231212075200.983536-10-yangchen.openbmc@gmail.comSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Add fan rpm controller max31790 on all bus of FCB.
Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231212075200.983536-9-yangchen.openbmc@gmail.comSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Add bus labels and aliases for the fan control board.
Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231212075200.983536-8-yangchen.openbmc@gmail.comSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Correct the address from 0x51 to 0x54 of eeprom on the i2c bus 1
Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231212075200.983536-7-yangchen.openbmc@gmail.comSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Add one temperature sensor on i2c bus 1
Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231212075200.983536-6-yangchen.openbmc@gmail.comSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Enable power monitor device ina230 and ltc2945 on the i2c bus 0
Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231212075200.983536-5-yangchen.openbmc@gmail.comSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Correct the sgpio use from sgpiom1 to sgpiom0
Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231212075200.983536-4-yangchen.openbmc@gmail.comSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Remove the unuse setting and fix the link to 100 M
Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231212075200.983536-3-yangchen.openbmc@gmail.comSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

The project Minerva which is the platform used by Meta has two boards: the
Chassis Management Module (Minerva) and the Motherboard (Harma), so change
the DTS name to minerva here for CMM use.
Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231212075200.983536-2-yangchen.openbmc@gmail.comSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Add linux device tree entry related to
the Meta(Facebook) computer-node system use an AT2600 BMC.
This node is named "Harma".
Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231211162656.2564267-3-peteryin.openbmc@gmail.comSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Document the new compatibles used on Meta Harma.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
Link: https://lore.kernel.org/r/20231211162656.2564267-2-peteryin.openbmc@gmail.comSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

This is a relatively low-cost AST2500-based Amd Ryzen 5000 Series
micro-ATX board that we hope can provide a decent platform for OpenBMC
development.

This initial device-tree provides the necessary configuration for
basic BMC functionality such as serial console, KVM support
and POST code snooping.
Signed-off-by: Renze Nicolai <renze@rnplus.nl>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231202003908.3635695-3-renze@rnplus.nlSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Document Asrock X570D4U compatible.
Signed-off-by: Renze Nicolai <renze@rnplus.nl>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231202003908.3635695-2-renze@rnplus.nlSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

This is a Xeon board broadly similar (aside from CPU vendor) to the
already-support romed8hm3 (half-width, single-socket, ast2500).  It
doesn't require anything terribly special for OpenBMC support, so this
device-tree should provide everything necessary for basic
functionality with it.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20231120121954.19926-6-zev@bewilderbeest.netSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Document ASRock SPC621D8HM3 board compatible.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231120121954.19926-5-zev@bewilderbeest.netSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>