* clk-sunxi:
  clk: sunxi: explicitly request exclusive reset control
  clk: sunxi: fix build warning

* clk-hikey:
  clk: hi3798cv200: correct parent mux clock for 'clk_sdio0_ciu'
  clk: hisilicon: Delete an error message for a failed memory allocation in hisi_register_clkgate_sep()
  clk: hi3660: fix incorrect uart3 clock freqency
  clk: hi6220: mark clock cs_atb_syspll as critical

Merge tag 'tegra-for-4.15-clk-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into clk-next

Pull tegra clk drivers updates from Thierry Reding:

This contains cleanups and minor fixes for the Tegra clock driver.

* tag 'tegra-for-4.15-clk-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  clk: tegra: Use readl_relaxed_poll_timeout_atomic() in tegra210_clock_init()
  clk: tegra: dfll: Fix drvdata overwriting issue
  clk: tegra: Fix cclk_lp divisor register
  clk: tegra: Bump SCLK clock rate to 216 MHz
  clk: tegra: Use common definition of APBDMA clock gate
  clk: tegra: Correct parent of the APBDMA clock
  clk: tegra: Add AHB DMA clock entry
  clk: tegra: Mark APB clock as critical
  clk: tegra: Make tegra_clk_pll_params __ro_after_init
  clk: tegra: Fix sor1_out clock implementation
  clk: tegra: Use tegra_clk_register_periph_data()
  clk: tegra: Add peripheral clock registration helper
  clk: tegra: Check BPMP response return code
  dt-bindings: clock: tegra: Add sor1_out clock
  firmware: tegra: Propagate error code to caller

Other than 'mmc_mux', 'clk_sdio0_ciu' uses a different parent mux clock.
Let's add this mux clock as 'sdio0_mux', and correct the parent of
'clk_sdio0_ciu' to be it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

clk: hisilicon: Delete an error message for a failed memory allocation in hisi_register_clkgate_sep()

Omit an extra message for a memory allocation failure in this function.

This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

UART3 clock rate is doubled in previous commit.

This error is not detected until recently a mezzanine board which makes
real use of uart3 port (through LS connector of 96boards) was setup
and tested on hi3660-hikey960 board.

This patch changes clock source rate of clk_factor_uart3 to 100000000.
Signed-off-by: Zhong Kaihua <zhongkaihua@huawei.com>
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Commit a53e35db ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.

No functional changes.

Cc: "Emilio López" <emilio@elopez.com.ar>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

This patch fix the following build warning:
drivers/clk/sunxi/clk-factors.c:279:14: warning: variable 'name' set but not used [-Wunused-but-set-variable]

Fixes: 4cbeaebb ("clk: sunxi: factors: Add unregister function")
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Clock cs_atb_syspll is pll used for coresight trace bus; when clock
cs_atb_syspll is disabled and operates its child clock node cs_atb
results in system hang. So mark clock cs_atb_syspll as critical to
keep it enabled.

Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Zhangfei Gao <zhangfei.gao@linaro.org>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1504226835-2115-2-git-send-email-leo.yan@linaro.org

Below is the call trace of tegra210_init_pllu() function:
  start_kernel()
  -> time_init()
  --> of_clk_init()
  ---> tegra210_clock_init()
  ----> tegra210_pll_init()
  -----> tegra210_init_pllu()

Because the preemption is disabled in the start_kernel before calling
time_init, tegra210_init_pllu is actually in an atomic context while
it includes a readl_relaxed_poll_timeout that might sleep.

So this patch just changes this readl_relaxed_poll_timeout() to its
atomic version.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Both tegra124-dfll and clk-dfll are using platform_set_drvdata
to set drvdata of the exact same pdev while they use different
pointers for the drvdata. Once the drvdata has been overwritten
by tegra124-dfll, clk-dfll will never get its td pointer as it
expects.

Since tegra124-dfll merely needs its soc pointer in its remove
function, this patch fixes the bug by removing the overwriting
in the tegra124-dfll file and letting the tegra_dfll_unregister
return an soc pointer for it.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

According to comments in code and common sense, cclk_lp uses its
own divisor, not cclk_g's.

Fixes: b08e8c0e ("clk: tegra: add clock support for Tegra30")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

AHB DMA is a running on 1/2 of SCLK rate, APB DMA on 1/4. Increasing SCLK
rate results in an increased DMA transfer rate.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

The APBDMA clock is defined in the common clock gates table that is used
by Tegra30+. Tegra20 can use it too, let's remove the custom definition
and use the common one.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

APBDMA represents a clock gate to the APB DMA controller, the actual
clock source for the controller is PCLK.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

AHB DMA engine presents on Tegra20/30. Add missing clock entries, so that
driver for the AHB DMA controller could be implemented.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Currently, the APB clock is registered with the CLK_IGNORE_UNUSED flag
to prevent the clock from being disabled if unused on boot. However,
even if it is used, it still needs to be always kept enabled so that it
doesn't get inadvertently disabled when all of its children are, and so
update the flag for the APB clock to be CLK_IS_CRITICAL.
Suggested-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Merge tag 'v4.15-rockchip-clk-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-next

Pull Rockchip clk drivers updates from Heiko Stuebner:

 - new clock ids for rk3188 and rk3368
 - removal of a superfluous memory allocation error message

* tag 'v4.15-rockchip-clk-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  clk: rockchip: use new cif/vdpu clock ids on rk3188
  clk: rockchip: export clock pclk_efuse_256 for RK3368 SoCs
  clk: rockchip: add more rk3188 graphics clock ids
  clk: rockchip: add clock id for PCLK_EFUSE256 of RK3368 SoCs
  clk: rockchip: Remove superfluous error message in rockchip_clk_register_cpuclk()

Merge tag 'clk-renesas-for-v4.15-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into clk-next

Pull Renesas clk driver updates from Geert Uytterhoeven:

  - Add support for the second display unit clock on RZ/G1E,
  - Add git repository to MAINTAINERS,
  - Add suspend/resume support for R-Car Gen3 CPG/MSSR,
  - Small fixes and cleanups.

* tag 'clk-renesas-for-v4.15-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers:
  clk: renesas: rcar-gen3: Restore R clock during resume
  clk: renesas: rcar-gen3: Restore SDHI clocks during resume
  clk: renesas: div6: Restore clock state during resume
  clk: renesas: cpg-mssr: Add support to restore core clocks during resume
  clk: renesas: cpg-mssr: Restore module clocks during resume
  MAINTAINERS: Add git repository to Renesas clock driver section
  clk: renesas: cpg-mssr: Add du1 clock to R8A7745
  clk: renesas: rz: clk-rz is meant for RZ/A1
  clk: renesas: r8a77995: Correct parent clock of INTC-AP
  clk: renesas: r8a7796: Correct parent clock of INTC-AP
  clk: renesas: r8a7795: Correct parent clock of INTC-AP

Pull Amlogic clock driver updates from Neil Armstrong:

 - Addition of Video Processing Unit VPU and VAPB clocks

* tag 'meson-clk-for-4.15' of git://github.com/baylibre/clk-meson:
  clk: meson: gxbb: Add VPU and VAPB clocks data
  clk: meson: gxbb: Add VPU and VAPB clockids

Merge tag 'sunxi-clk-for-4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into clk-next

Pull Allwinner clock driver updates from Maxime Ripard:

  - Addition of sigma/delta modulation for the audio PLLs on the newer SoCs
  - A83t Display clocks supports
  - minor fixes that didn't have any impact on current features

* tag 'sunxi-clk-for-4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  clk: sunxi-ng: sun4i: Export video PLLs
  clk: sunxi-ng: Add A83T display clocks
  clk: sunxi-ng: sun8i: a23: Use sigma-delta modulation for audio PLL
  clk: sunxi-ng: sun6i: Use sigma-delta modulation for audio PLL
  clk: sunxi-ng: sun5i: Use sigma-delta modulation for audio PLL
  clk: sunxi-ng: sun4i: Use sigma-delta modulation for audio PLL
  clk: sunxi-ng: sun8i: h3: Use sigma-delta modulation for audio PLL
  clk: sunxi-ng: nm: Add support for sigma-delta modulation
  clk: sunxi-ng: Add sigma-delta modulation support
  clk: sunxi-ng: nm: Check if requested rate is supported by fractional clock
  clk: sunxi-ng: sun5i: Fix bit offset of audio PLL post-divider
  clk: sunxi-ng: a83t: Fix invalid csi-mclk mux offset
  clk: sunxi-ng: sun6i: Rename HDMI DDC clock to avoid name collision
  clk: sunxi-ng: sun6i: Export video PLLs
  clk: sunxi-ng: Implement reset control status readback
  clk: sunxi-ng: Fix missing CLK_SET_RATE_PARENT in ccu-sun4i-a10.c
  clk: sunxi-ng: add CLK_SET_RATE_PARENT flag to H3 GPU clock
  clk: sunxi-ng: add CLK_SET_RATE_UNGATE to all H3 PLLs

Merge tag 'clk-v4.15-exynos-pm' of git://git.kernel.org/pub/scm/linux/kernel/git/snawrocki/clk into clk-next

Pull Samsung clk driver updates from Sylwester Nawrocki:

 - An addition of separate driver for the Exynos 4412 ISP CMU, needed
   to model and properly handle the clock controller's dependencies
   on the ISP power domain.
 - Adding __maybe_unused attributes to the exynos5433_cmu_{suspend,
   resume} ops to suppress compiler warnings with CONFIG_PM disabled.

* tag 'clk-v4.15-exynos-pm' of git://git.kernel.org/pub/scm/linux/kernel/git/snawrocki/clk:
  clk: samsung: Add a separate driver for Exynos4412 ISP clocks
  clk: samsung: Add dt bindings for Exynos4412 ISP clock controller
  clk: samsung: Instantiate Exynos4412 ISP clocks only when available
  clk: samsung: exynos5433: mark PM functions as __maybe_unused

Merge tag 'clk-v4.15-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/snawrocki/clk into clk-next

Pull Samsung clk driver updates from Sylwester Nawrocki:

Overall clk/samsung clean up and fixes. Removed remaining unused code
after removal of exynos4212 SoC support; dropped internal data structure
fields and related code for registering clkdev lookup entry for each
possible clock object, clkdev aliases could still be defined if needed
in a separate table; other minor fixes of the clock tree definitions.

* tag 'clk-v4.15-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/snawrocki/clk:
  clk: samsung: Remove obsolete clkdev alias support
  clk: samsung: Add explicit MPLL, EPLL clkdev aliases in S3C2443 driver
  clk: samsung: Rework clkdev alias handling in S3C2443 driver
  clk: samsung: Rework clkdev alias handling in Exynos5440 driver
  clk: samsung: Drop useless alias in Exynos5420 clk driver
  clk: samsung: Remove clkdev alias support in Exynos5250 clk driver
  clk: samsung: Remove double assignment of CLK_ARM_CLK in Exynos4 driver
  clk: samsung: Remove clkdev alias support in Exynos4 clk driver
  clk: samsung: Remove support for obsolete Exynos4212 CPU clock
  clk: samsung: Remove support for Exynos4212 SoCs in Exynos CLKOUT driver
  clk: samsung: Properly propagate flags in __PLL macro
  clk: samsung: Fix m2m scaler clock on Exynos542x
  clk: samsung: Delete a memory allocation error message in clk-cpu.c

Merge tag 'clk-renesas-for-v4.15-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into clk-next

Pull Renesas clk driver updates from Geert Uytterhoeven:

  - Add support for the new R-Car V3M SoC,
  - Small fixes and cleanups.

* tag 'clk-renesas-for-v4.15-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers:
  clk: renesas: rcar-gen2: Delete error message for failed memory allocation
  clk: renesas: mstp: Delete error messages for failed memory allocations
  clk: renesas: cpg-mssr: Add R8A77970 support
  dt-bindings: clock: Add R8A77970 CPG core clock definitions

On R-Car Gen3 systems, PSCI system suspend powers down the SoC, losing
clock configuration.  Register a notifier to save/restore the RCKCR
register during system suspend/resume.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>

On R-Car Gen3 systems, PSCI system suspend powers down the SoC, losing
clock configuration.  Register a notifier to save/restore SDHI clock
registers during system suspend/resume.

This is implemented using the cpg_simple_notifier abstraction, which can
be reused for others clocks that just need to save/restore a single
register.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>

On R-Car Gen3 systems, PSCI system suspend powers down the SoC, losing
clock configuration.  Register an (optional) notifier to restore the
DIV6 clock state during system resume.

As DIV6 clocks can be picky w.r.t. modifying multiple register fields at
once, restore is not implemented by blindly restoring the register
value, but by using the existing cpg_div6_clock_{en,dis}able() helpers.

Note that this does not yet support DIV6 clocks with multiple parents,
which do not exist on R-Car Gen3 SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>

On R-Car Gen3 systems, PSCI system suspend powers down the SoC, possibly
losing clock configuration.  Hence add a notifier chain that can be used
by core clocks to save/restore clock state during system suspend/resume.

The implementation of the actual clock state save/restore operations is
clock-specific, and to be registered with the notifier chain in the SoC
or family-specific cpg_mssr_info.cpg_clk_register() callback.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>

During PSCI system suspend, R-Car Gen3 SoCs are powered down, and their
clock register state is lost.  Note that as the boot loader skips most
initialization after system resume, clock register state differs from
the state encountered during normal system boot, too.

Hence after s2ram, some operations may fail because module clocks are
disabled, while drivers expect them to be still enabled.  E.g. EtherAVB
fails when Wake-on-LAN has been enabled using "ethtool -s eth0 wol g":

    ravb e6800000.ethernet eth0: failed to switch device to config mode
    ravb e6800000.ethernet eth0: device will be stopped after h/w processes are done.
    ravb e6800000.ethernet eth0: failed to switch device to config
    PM: Device e6800000.ethernet failed to resume: error -110

In addition, some module clocks that were disabled by
clk_disable_unused() may have been re-enabled, wasting power.

To fix this, restore all bits of the SMSTPCR registers that represent
clocks under control of Linux.

Notes:
  - While this fixes EtherAVB operation after resume from s2ram,
    EtherAVB cannot be used as an actual wake-up source from s2ram, only
    from s2idle, due to PSCI limitations,
  - To avoid overhead on platforms not needing it, the suspend/resume
    code has a build time dependency on sleep and PSCI support, and a
    runtime dependency on PSCI.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>

Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

The RZ family of Renesas SoCs has several different subfamilies (RZ/A,
RZ/G, RZ/N, and RZ/T).  Clarify that the renesas,rz-cpg-clocks DT
bindings and clk-rz driver apply to RZ/A1 only.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>

The Amlogic Meson GX SoCs needs these two clocks to power up the
VPU power domain.

These two clocks are similar to the MALI clocks by having a glitch-free
mux and two similar clocks with gate, divider and muxes.
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
[narmstrong: removed the CLK_IGNORE_UNUSED on muxes and dividers]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

Add the clkids for the clocks feeding the Video Processing Unit.
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

These structures are only passed to the functions tegra_clk_register_pll,
tegra_clk_register_pll{e/u} or tegra_periph_clk_init during the init
phase. These functions modify the structures only during the init phase
and after that the structures are never modified. Therefore, make them
__ro_after_init.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

This clock was previously called sor1_src and was modelled as an input
to the sor1 module clock. However, it's really an output clock that can
be fed either from the safe, the sor1_pad_clkout or the sor1 module
clocks. sor1 itself can take input from either of the display PLLs.

The same implementation for the sor1_out clock is used on Tegra186, so
this nicely lines up both SoC generations to deal with this clock in a
uniform way.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Instead of open-coding the same pattern repeatedly, reuse the newly
introduced tegra_clk_register_periph_data() helper that will unpack
the initialization structure.
Signed-off-by: Thierry Reding <treding@nvidia.com>

There is a common pattern that registers individual peripheral clocks
from an initialization table. Add a common implementation to remove the
duplication from various call sites.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Check return code in BPMP response message(s). The typical error case is
when a clock operation is attempted with an invalid clock identifier.

Also remove error print from call to clk_get_info() as the
implementation loops through the range of all possible identifiers, yet
the operation is expected to error out when the clock ID is unused.
Signed-off-by: Timo Alho <talho@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>