- 27 Sep, 2019 6 commits
-
-
Clinton A Taylor authored
BSpec was updated(r146548) with a new MG_DP_MODE Programming table, now taking in consideration the pin assignment and allowing us to optimize power by shutting down available but not needed lanes. It was tested on ICL and TGL, with adaptors that used pin assignment C and B, reversing the connector and going to different modes testing the not needed lane shutdown. v5: Using crtc_state->lane_count instead of dp.lane_count BSpec: 21735 BSpec: 49292 Cc: Imre Deak <imre.deak@intel.com> Cc: Lucas De Marchi <lucas.demarchi@intel.com> Reviewed-by:
Imre Deak <imre.deak@intel.com> Signed-off-by:
Clinton A Taylor <clinton.a.taylor@intel.com> Signed-off-by:
José Roberto de Souza <jose.souza@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190926210659.56317-1-jose.souza@intel.com
-
Anusha Srivatsa authored
We have a new version of DMC for ICL - v1.09. This version adds the Half Refresh Rate capability into DMC. Cc: José Roberto de Souza <jose.souza@intel.com> Signed-off-by:
Anusha Srivatsa <anusha.srivatsa@intel.com> Reviewed-by:
Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190925201250.18136-1-daniele.ceraolospurio@intel.com
-
Daniele Ceraolo Spurio authored
The HuC FW has silently switched to encoding the version the same way as the GuC FW does, i.e. major.minor.patch instead of just major.minor. All the current blobs follow the new scheme, but since minor and patch are both zero there is no difference in the end results and we happily load them. New binaries, however, will have non-zero values in there, so we need to make sure to parse them correctly. Signed-off-by:
Stuart Summers <stuart.summers@intel.com> Acked-by:
Michal Wajdeczko <michal.wajdeczko@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190925222121.4000-1-daniele.ceraolospurio@intel.com
-
Joonas Lahtinen authored
Signed-off-by:Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
-
Andi Shyti authored
Continuing the theme of breaking intel_pm.c up in a reasonable chunk of powermanagement utilities, pull out the rc6 setup into its GT handler. Based on a patch by Chris Wilson. Signed-off-by:
Andi Shyti <andi.shyti@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by:
Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by:
-
Chris Wilson authored
The simplest and most maximal submission we can do, a thread to submit requests unto each engine. Signed-off-by:
Mika Kuoppala <mika.kuoppala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190925193446.26007-1-chris@chris-wilson.co.uk
-
- 26 Sep, 2019 8 commits
-
-
Michał Winiarski authored
We can use it in i915 for updating parts of unmasked registers from within a batch. We're also adding Gen8+ versions of CS_GPR registers (aka MI_MATH_REG in the coprocessor). Signed-off-by:
Michał Winiarski <michal.winiarski@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by:
-
Anna Karas authored
Insert structure members names into their descriptions to follow kernel-doc format. Cc: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by:
Anna Karas <anna.karas@intel.com> Reviewed-by:
Lionel Landwerlin <lionel.g.landwerlin@intel.com> Signed-off-by:
-
Sebastian Andrzej Siewior authored
The function intel_engine_breadcrumbs_irq() is always invoked from an interrupt handler and for that reason it invokes (as an optimisation) only spin_lock() for locking assuming that the interrupts are already disabled. The function intel_engine_signal_breadcrumbs() is provided to disable interrupts while the former function is invoked so that assumption is also true for callers from preemptible context. On PREEMPT_RT local_irq_disable() really disables interrupts and this forbids to invoke spin_lock() which becomes a sleeping spinlock. This is also problematic with `threadirqs' in conjunction with irq_work. With force threading the interrupt handler, the handler is invoked with disabled BH but with interrupts enabled. This is okay and the lock itself is never acquired in IRQ context. This changes with irq_work (signal_irq_work()) which _still_ invokes intel_engine_breadcrumbs_irq() from IRQ context. Lockdep should see this and complain. Acquire the locks in intel_engine_breadcrumbs_irq() with _irqsave() suffix and let all callers invoke intel_engine_breadcrumbs_irq() directly instead using intel_engine_signal_breadcrumbs(). Reported-by:
Clark Williams <williams@redhat.com> Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by:
-
Sebastian Andrzej Siewior authored
The lockdep_assert_irqs_disabled() check is needless. The previous lockdep_assert_held() check ensures that the lock is acquired and while the lock is acquired lockdep also prints a warning if the interrupts are not disabled if they have to be. These IRQ-off asserts trigger on PREEMPT_RT because the locks become sleeping locks and do not really disable interrupts. Remove lockdep_assert_irqs_disabled(). Reported-by:
-
Michał Winiarski authored
Default length value of MI_LOAD_REGISTER_REG is 1. Also move it out of cmd-parser-only registers since we're going to use it in i915. Signed-off-by:
-
Michał Winiarski authored
Some of our commands (MI_FLUSH_DW / PIPE_CONTROL) require a post-sync write operation to be performed. Currently we're using dedicated VMA for PIPE_CONTROL and global HWSP for MI_FLUSH_DW. On execlists platforms, each of our contexts has an area that can be used as scratch space. Let's use that instead. Signed-off-by:
-
Michał Winiarski authored
We're currently using scratch presence as a way of identifying that we entered wedged state at driver initialization time. Let's use a separate flag rather than rely on scratch. Signed-off-by:
-
Matt Roper authored
According to the bspec, GLK/CNL have a smaller small joiner RAM buffer than ICL+. This feels like something that could easily change again on future platforms, so let's just add a function to return the proper per-platform buffer size. That may also slightly simplify the upcoming bigjoiner enabling. Since we have to change intel_dp_dsc_get_output_bpp()'s signature to pass the dev_priv down for the platform check, let's take the opportunity to also make that function static since it isn't used outside the intel_dp file. v2: Minor rebase on top of Maarten's changes. Bspec: 20388 Bspec: 49259 Cc: Manasi Navare <manasi.d.navare@intel.com> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Signed-off-by:
Matt Roper <matthew.d.roper@intel.com> Reviewed-by:
Manasi Navare <manasi.d.navare@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190925234542.24289-1-matthew.d.roper@intel.com
-
- 25 Sep, 2019 13 commits
-
-
James Ausmus authored
The memory type values have changed in TGL, so we need to translate them differently than ICL. While we're moving it, fix up the ICL translation for LPDDR4. BSpec: 53998 v2: Fix up ICL LPDDR4 entry (Ville); Drop unused values from TGL (Ville) Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> Signed-off-by:
James Ausmus <james.ausmus@intel.com> Reviewed-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by:
Lucas De Marchi <lucas.demarchi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190924222829.13142-1-james.ausmus@intel.com
-
José Roberto de Souza authored
TGL added 2 more TC ports that currently are not being handled by icl_pll_to_ddi_clk_sel(), so adding those. Reviewed-by:
-
José Roberto de Souza authored
Extending ICL mg calculations to also support dkl calculations. v3: Fixing iref_trim calculation for 38400 refclock BSpec: 49204 Reviewed-by:
Vandita Kulkarni <vandita.kulkarni@intel.com> Signed-off-by:
-
Lucas De Marchi authored
The final save operation into pll_state of the calculations done will be different for DKL PHY. Prepare for that by reindenting code so it's easier to check for correctness. This one has no change in behavior. Reviewed-by:
-
Vandita Kulkarni authored
Add a new function to write to dkl phy pll registers. As per the bspec all the registers are read modify write. Reviewed-by:
-
Lucas De Marchi authored
The disable function can be the same as for MG phy since the same registers are used. The others are different as registers changed, also adding a empty dkl_pll_write() to be implemented later. v2: Setting the right HIP_INDEX_REG bits (José) v3: Masking non-computed registers of mg_pll_tdc_coldst_bias when getting hardware state Sharing mg_pll_enable() with TGL Reviewed-by:
-
Chris Wilson authored
Having decided that we only care about the promotion predicate, we can simplify gen12_csb_parse to simply check whether we need to jump to a new queue. Signed-off-by:
-
Maarten Lankhorst authored
We cannot switch between HQ and normal mode on GLK+, so only add planes on platforms where it makes sense. We could probably restrict it even more to only add when scaler users toggles between 1 and 2, but lets just leave it for now. Signed-off-by:
Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190920114235.22411-9-maarten.lankhorst@linux.intel.comReviewed-by:
-
Maarten Lankhorst authored
Rename linked_plane to planar_linked_plane and slave to planar_slave, this will make it easier to keep apart bigjoiner linking and planar plane linking. Signed-off-by:
-
Maarten Lankhorst authored
We had this as an optimization to not do a plane update, but we killed it off because there are so many reasons we may have to do a plane update or fastset that it's best to just assume everything changed. Signed-off-by:
-
Maarten Lankhorst authored
Readout the FEC state in encoder->get_config(), this will allow us to ensure that we can correctly inherit the state from boot, and that we set FEC during modeset. Signed-off-by:
-
Maarten Lankhorst authored
There was a integer wraparound when mode_clock became too high, and we didn't correct for the FEC overhead factor when dividing, with the calculations breaking at HBR3. As a result our calculated bpp was way too high, and the link width limitation never came into effect. Print out the resulting bpp calcululations as a sanity check, just in case we ever have to debug it later on again. We also used the wrong factor for FEC. While bspec mentions 2.4%, all the calculations use 1/0.972261, and the same ratio should be applied to data M/N as well, so use it there when FEC is enabled. This fixes the FIFO underrun we are seeing with FEC enabled. Changes since v2: - Handle fec_enable in intel_link_compute_m_n, so only data M/N is adjusted. (Ville) - Fix initial hardware readout for FEC. (Ville) Changes since v3: - Remove bogus fec_to_mode_clock. (Ville) Changes since v4: - Use the correct register for icl. (Ville) - Split hw readout to a separate patch. Signed-off-by:
-
Swati Sharma authored
This reverts commit 84af7649. This is causing problems with the display, displays are all bright colors. Fixes: 84af7649 ("drm/i915/color: Extract icl_read_luts()") Signed-off-by:
Swati Sharma <swati2.sharma@intel.com> Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190924135820.11850-1-swati2.sharma@intel.com
-
- 24 Sep, 2019 5 commits
-
-
Chris Wilson authored
If we disable rps, it appears the Tigerlake is stable enough to run multiple engines simultaneously in CI. As disabling rps should only cause the execution to be slow, whereas many features depend on the different engines, we would prefer to have the engines enabled while the machine hangs are being debugged. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111714Signed-off-by:
-
Ankit Nautiyal authored
Currently the offset for PIPE D cursor control register is missing in i915_reg.h due to which the cursor plane cannot be enabled for Pipe D. This also causes kernel Warning, when a user requests to enable cursor plane for PIPE D for Gen 12 platforms. This patch adds the CURSOR_CTL_D register in the i915_reg.h. v2: Rebase Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111640Signed-off-by:
Ankit Nautiyal <ankit.k.nautiyal@intel.com> Reviewed-by:
-
Chris Wilson authored
Before we submit the first context to HW, we need to construct a valid image of the register state. This layout is defined by the HW and should match the layout generated by HW when it saves the context image. Asserting that this should be equivalent should help avoid any undefined behaviour and verify that we haven't missed anything important! Of course, having insisted that the initial register state within the LRC should match that returned by HW, we need to ensure that it does. v2: Drop the RELATIVE_MMIO flag from gen11, we ignore it for constructing the lrc image. Signed-off-by:
-
Stanislav Lisovskiy authored
Added bandwidth calculation algorithm and checks, similar way as it was done for ICL, some constants were corrected according to BSpec 53998. v2: Start using same icl_get_bw_info function to avoid code duplication. Moved mpagesize to memory info related structure as it is now dependent on memory type. Fixed qi.t_bl field assignment. v3: Removed mpagesize as unused. Duplicate code and redundant blankline fixed. v4: Changed ordering of IS_GEN checks as agreed. Minor commit message fixes. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111600Reviewed-by:Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> Signed-off-by:
-
Chris Wilson authored
Since dropping the set-to-gtt-domain in commit a679f58d ("drm/i915: Flush pages on acquisition"), we no longer mark the contents as dirty on a write fault. This has the issue of us then not marking the pages as dirty on releasing the buffer, which means the contents are not written out to the swap device (should we ever pick that buffer as a victim). Notably, this is visible in the dumb buffer interface used for cursors. Having updated the cursor contents via mmap, and swapped away, if the shrinker should evict the old cursor, upon next reuse, the cursor would be invisible. E.g. echo 80 > /proc/sys/kernel/sysrq ; echo f > /proc/sysrq-trigger Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111541 Fixes: a679f58d ("drm/i915: Flush pages on acquisition") Signed-off-by:
Matthew Auld <matthew.william.auld@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190920121821.7223-1-chris@chris-wilson.co.uk
-
- 23 Sep, 2019 8 commits
-
-
Chris Wilson authored
Force bonded requests to run on distinct engines so that they cannot be shuffled onto the same engine where timeslicing will reverse the order. A bonded request will often wait on a semaphore signaled by its master, creating an implicit dependency -- if we ignore that implicit dependency and allow the bonded request to run on the same engine and before its master, we will cause a GPU hang. [Whether it will hang the GPU is debatable, we should keep on timeslicing and each timeslice should be "accidentally" counted as forward progress, in which case it should run but at one-half to one-third speed.] We can prevent this inversion by restricting which engines we allow ourselves to jump to upon preemption, i.e. baking in the arrangement established at first execution. (We should also consider capturing the implicit dependency using i915_sched_add_dependency(), but first we need to think about the constraints that requires on the execution/retirement ordering.) Fixes: 8ee36e04 ("drm/i915/execlists: Minimalistic timeslicing") References: ee113690 ("drm/i915/execlists: Virtual engine bonding") Testcase: igt/gem_exec_balancer/bonded-slice Signed-off-by:
Tvrtko Ursulin <tvrtko.ursulin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190923152844.8914-3-chris@chris-wilson.co.uk
-
Chris Wilson authored
Due to the nature of preempt-to-busy the execlists active tracking and the schedule queue may become temporarily desync'ed (between resubmission to HW and its ack from HW). This means that we may have unwound a request and passed it back to the virtual engine, but it is still inflight on the HW and may even result in a GPU hang. If we detect that GPU hang and try to reset, the hanging request->engine will no longer match the current engine, which means that the request is not on the execlists active list and we should not try to find an older incomplete request. Given that we have deduced this must be a request on a virtual engine, it is the single active request in the context and so must be guilty (as the context is still inflight, it is prevented from being executed on another engine as we process the reset). Fixes: 22b7a426 ("drm/i915/execlists: Preempt-to-busy") Signed-off-by:
-
Chris Wilson authored
As preempt-to-busy leaves the request on the HW as the resubmission is processed, that request may complete in the background and even cause a second virtual request to enter queue. This second virtual request breaks our "single request in the virtual pipeline" assumptions. Furthermore, as the virtual request may be completed and retired, we lose the reference the virtual engine assumes is held. Normally, just removing the request from the scheduler queue removes it from the engine, but the virtual engine keeps track of its singleton request via its ve->request. This pointer needs protecting with a reference. v2: Drop unnecessary motion of rq->engine = owner Fixes: 22b7a426 ("drm/i915/execlists: Preempt-to-busy") Signed-off-by:
-
José Roberto de Souza authored
New step added for TGL, required for us to check the TC microcontroller health after power on TC aux. BSpec: 49294 Reviewed-by:
-
José Roberto de Souza authored
Adding a enable parameters allow us to share most of the code between enable and disable functions. v3: Renamed icl_phy_clock_gating() to icl_phy_set_clock_gating() Reviewed-by:
-
Vandita Kulkarni authored
These are the registers needed to program Dekel phy. Some register definitions will be reused from MG PHY definitions, so adding a comment on those. Bspec: 49295 Reviewed-by:
-
Clinton A Taylor authored
Commit 24a7bfe0 ("drm/i915: Keep the TypeC port mode fixed when the port is active") added this new hook while in parallel TGL upstream was happening and this was missed. Without this driver will crash when TC DDI is added and driver is preparing to do a full modeset. Cc: Lucas De Marchi <lucas.demarchi@intel.com> Cc: Imre Deak <imre.deak@intel.com> Reviewed-by:
-
José Roberto de Souza authored
If platform supports and has modular FIA is enabled, the registers bits also change, example: reading TC3 registers with modular FIA enabled, driver should read from FIA2 but with TC1 bits offsets. It is described in BSpec 50231 for DFLEXDPSP, other registers don't have the BSpec description but testing in real hardware have proven that it had moved for all other registers too. v2: - Caching index in tc_phy_fia_idx, instead of calculate it each time v3: - Setting tc_phy_fia and tc_phy_fia_idx in the same function Cc: Lucas De Marchi <lucas.demarchi@intel.com> Reviewed-by:
-
