- 03 Dec, 2015 40 commits
-
-
Jiri Pirko authored
LAG-related records have specific format in SFN register. Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
LAG-related records have specific format in SFD register. Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
Add definitions of SLDR, SLCR2, SLCOR registers that are used to configure LAG. Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
Completion queue element for receive queue provides information if the packet was received via LAG port. Extract this info and pass it along to core. Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
Lower layer (pci) has information if the packet is received via LAG port. If that is the case, it fills up rx_info accordingly. However upper layer does not care about lag_id/port_index for received packets so convert it to local_port before passing it up. For that conversion, lag mapping array is introduced. Upper layer is responsible for setting up the mapping according to what is set in HW. Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
Add just a stub for now. This allows to pass check in dev_ifsioc, SIOCADDMULTI and SIOCDELMULTI cases. Teamd is using these to add LACP slow MAC. Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
Be correct and symmetric to enslave and set inactive flags during release. That gives LAG offload drivers - lower state change listeners - possibility to do proper cleanup. Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
Let netdev notifier listeners know about link and slave state change. Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
Similar to state notifications. We allow caller to indicate if the notification should happen now or later, depending on if he holds rtnl mutex or not. Introduce bond_slave_link_notify function (similar to bond_slave_state_notify) which is later on called with rtnl mutex and goes over slaves and executes delayed notification. Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
Let netdev notifier listeners know about link-up and port-enable state changes. Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
During options set, there will be needed to hold rtnl_mutex in order to safely call netdev notifiers. Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
This is shared info structure for bonding and team. Serves to pass down info about link state and port activity to notification listeners. Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
When lower device like bonding slave, team/bridge port, etc changes its state, it is useful for others to notice this change. Currently this is implemented specificly for bonding as NETDEV_BONDING_INFO notifier. This patch aims to replace this specific usage and make this more generic to be used for all upper-lower devices. Introduce NETDEV_CHANGELOWERSTATE netdev notifier type and netdev_lower_state_changed() helper. Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
Initialize netdev_lag_upper_info structure by TX type according to current bonding mode and pass it along via netdev_master_upper_dev_link. Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Reviewed-by:
Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
Initialize netdev_lag_upper_info structure by TX type according to current team mode and pass it along via netdev_master_upper_dev_link. Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
This struct will be shared by bonding and team to pass internal information to notifier listeners. Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
Sometimes the drivers and other code would find it handy to know some internal information about upper device being changed. So allow upper-code to pass information down to notifier listeners during linking. Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
Eliminate netdev_master_upper_dev_link_private and pass priv directly as a parameter of netdev_master_upper_dev_link. Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
Some code does not mind if a device is bond slave or team port and treats them the same, as generic LAG ports. Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
Some code does not mind if the master is bond or team and treats them the same, as generic LAG. Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
Similar to other helpers, caller can use this to find out if device is team port. Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
Similar to other helpers, caller can use this to find out if device is team master. Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
Similar to other speeds, add 100G to bonding 802.3ad code. Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
Since CHANGEUPPER can now fail, add support for it in the newly introduced netdev notifier error injection infrastructure. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Acked-by:
Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
switchdev drivers reflect the newly requested topology to hardware when CHANGEUPPER is received, after software links were already formed. However, the operation can fail and user will not be notified, as the return value of the notifier is not checked. Add this check and rollback software links if necessary. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Joe Perches authored
Commit 7fd89545 ("i40e: remove BUG_ON from feature string building") added defective output when I40E_FLAG_VEB_MODE_ENABLED was set in function i40e_print_features. Fix it. Miscellanea: - Remove unnecessary string variable - Add space before not after fixed strings - Use kmalloc not kzalloc - Don't initialize i to 0, use result of first snprintf Reported-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
Joe Perches <joe@perches.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queueDavid S. Miller authored
Jeff Kirsher says: ==================== Intel Wired LAN Driver Updates 2015-12-03 This series contains updates to ixgbe and ixgbevf only. Mark cleans up ixgbe_init_phy_ops_x550em, since this was designed to initialize function pointers only and moves the KR PHY reset to the ixgbe_setup_internal_phy_t_x550em which was designed to detect which mode the PHY operates in and set it up. Added the new thermal alarm type support used with newer X550EM_x devices. Fixed both ixgbe and ixgbevf to use a private work queue to avoid hangs, which would possibly occur when creating and destroying many VFS repeatedly. Updated ixgbe PTP implementation to accommodate X550EM_x devices, which handle clocking differently. Fixed specification violations in the datasheet, which was reported by Dan Streetman. Fixed ixgbe to check for and handle IPv6 extended headers so that Tx checksum offload can be done, which was reported by Tom Herbert. Fixed ixgbe link issue for some systems with X540 or X550 by only inhibiting the turning PHY power off when manageability is present. Alex Duyck refactors the MAC address configuration code, which in turns fixes an issue where once 63 entries had been used, you could no longer add additional filters. Updated ixgbe to use __dev_uc_sync which also resolved an issue in which you could not remove an FDB address without having to reset the port. Updated the ixgbe driver to make use of all the free RAR entries for FDB use if needed. v2: updated patch 13 to "Alex Duyck Approved" version, in the original submission, I had grabbed a previous version of the patch and did not catch it was superseded by a later version ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Mark Rustad authored
Check for and handle IPv6 extended headers so that Tx checksum offload can be done. Also use skb_checksum_help for unexpected cases. Thanks to Tom Herbert for noticing these problems. Thanks to Alexander Duyck for seeing how to coalesce the error handling into one location. Reported-by:
Tom Herbert <tom@herbertland.com> Signed-off-by:
Mark Rustad <mark.d.rustad@intel.com> Tested-by:
Darin Miller <darin.j.miller@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Mark Rustad authored
Instead of inhibiting PHY power control when manageability is present, only inhibit turning PHY power off when manageability is present. Consequently, PHY power will always be turned on when requested. Without this patch, some systems with X540 or X550 devices in some conditions will never get link. Signed-off-by:
Mark Rustad <mark.d.rustad@intel.com> Tested-by:
Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Mark Rustad authored
Check for and handle IPv6 extended headers so that Tx checksum offload can be done. Also use skb_checksum_help for unexpected cases. Thanks to Tom Herbert for noticing these problems. Thanks to Alexander Duyck for recognizing problems with the first version of this patch and recognizing how to coalesce error conditions into a single location. Reported-by:
Tom Herbert <tom@herbertland.com> Signed-off-by:
Mark Rustad <mark.d.rustad@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Mark Rustad authored
Save VF device pointers and take references to speed accesses used to monitor the device behavior to avoid slot resets. The saved information avoids lock contention during the search used to access each of the VFs. Signed-off-by:
Mark Rustad <mark.d.rustad@intel.com> Tested-by:
Darin Miller <darin.j.miller@intel.com> Tested-by:
Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Mark Rustad authored
According to the datasheets, the driver should wait for the master disable bit to read as being set before checking the status register for master disable. Reported-by:
Dan Streetman <dan.streetman@canonical.com> Signed-off-by:
Mark Rustad <mark.d.rustad@intel.com> Tested-by:
Darin Miller <darin.j.miller@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Mark Rustad authored
The ixgbe driver was violating the specification in the datasheet by not waiting 1ms before checking for the reset bit clearing. This is called out for devices supported by ixgbe, so implement the required delay. Reported-by:
Dan Streetman <dan.streetman@canonical.com> Signed-off-by:
Mark Rustad <mark.d.rustad@intel.com> Tested-by:
Darin Miller <darin.j.miller@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Mark Rustad authored
The X550EM_x devices handle clocking differently, so update the PTP implementation to accommodate them. This involves significant changes to ixgbe's PTP code to accommodate the new range of behaviors including things like non-power-of-2 clock wrapping. Signed-off-by:
Mark Rustad <mark.d.rustad@intel.com> Tested-by:
Darin Miller <darin.j.miller@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Alexander Duyck authored
This change makes it so that we allow the PF to make use of all free RAR entries for FDB use if needed. Previously the code limited us to 16 unicast entries, however this was shared between MACVLAN which wasn't limited and the FDB code which was. So instead of treating the FDB code as a second class citizen I have updated it so that it has access to just as many entries as the MACVLAN filters. Signed-off-by:
Alexander Duyck <aduyck@mirantis.com> Tested-by:
Darin Miller <darin.j.miller@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Alexander Duyck authored
This change replaces the ixgbe_write_uc_addr_list call in ixgbe_set_rx_mode with a call to __dev_uc_sync instead. This works much better with the MAC addr list code that was already in place and solves an issue in which you couldn't remove an FDB address without having to reset the port. Signed-off-by:
Alexander Duyck <aduyck@mirantis.com> Tested-by:
Darin Miller <darin.j.miller@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Alexander Duyck authored
In the process of tracking down a memory leak when adding/removing FDB entries I had to go through the MAC address configuration code for ixgbe. In the process of doing so I found a number of issues that impacted readability and performance. This change updates the code in general to clean it up so it becomes clear what each step is doing. From what I can tell there a couple of bugs cleaned up in this code. First is the fact that the MAC addresses were being double counted for the PF. As a result once entries up to 63 had been used you could no longer add additional filters. A simple test case for this: for i in `seq 0 96` do ip link add link ens8 name mv$i type macvlan ip link set dev mv$i up done Test script: ethregs -s 0:8.0 | grep -e "RAH" | grep 8000....$ When things are working correctly RAL/H registers 1 - 97 will be consumed. In the failing case it will stop at 63 and prevent any further filters from being added. Signed-off-by:
Alexander Duyck <aduyck@mirantis.com> Tested-by:
Darin Miller <darin.j.miller@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Mark Rustad authored
Make some minor cleanups, such as simplifying return paths, deleting unneeded initializations, return values more directly and so forth. Signed-off-by:
Mark Rustad <mark.d.rustad@intel.com> Tested-by:
Darin Miller <darin.j.miller@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Mark Rustad authored
Use a private workqueue to avoid hangs that were otherwise possible when performing stress tests, such as creating and destroying many VFS repeatedly. Signed-off-by:
Mark Rustad <mark.d.rustad@intel.com> Tested-by:
Darin Miller <darin.j.miller@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Mark Rustad authored
Use a private workqueue to avoid hangs that were otherwise possible when performing stress tests, such as creating and destroying many VFS repeatedly. Signed-off-by:
Mark Rustad <mark.d.rustad@intel.com> Tested-by:
Darin Miller <darin.j.miller@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-