1. 11 Sep, 2008 25 commits
  2. 10 Sep, 2008 4 commits
  3. 09 Sep, 2008 11 commits
    • Simon Horman's avatar
    • David S. Miller's avatar
      ipsec: Make xfrm_larval_drop default to 1. · 28faa979
      David S. Miller authored
      The previous default behavior is definitely the least user
      friendly.  Hanging there forever just because the keying
      daemon is wedged or the refreshing of the policy can't move
      forward is anti-social to say the least.
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      28faa979
    • Neil Horman's avatar
      ipv6: Fix OOPS in ip6_dst_lookup_tail(). · e550dfb0
      Neil Horman authored
      This fixes kernel bugzilla 11469: "TUN with 1024 neighbours:
      ip6_dst_lookup_tail NULL crash"
      
      dst->neighbour is not necessarily hooked up at this point
      in the processing path, so blindly dereferencing it is
      the wrong thing to do.  This NULL check exists in other
      similar paths and this case was just an oversight.
      
      Also fix the completely wrong and confusing indentation
      here while we're at it.
      
      Based upon a patch by Evgeniy Polyakov.
      Signed-off-by: default avatarNeil Horman <nhorman@tuxdriver.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      e550dfb0
    • Herbert Xu's avatar
      ipsec: Restore larval states and socket policies in dump · 225f4005
      Herbert Xu authored
      The commit commit 4c563f76 ("[XFRM]:
      Speed up xfrm_policy and xfrm_state walking") inadvertently removed
      larval states and socket policies from netlink dumps.  This patch
      restores them.
      Signed-off-by: default avatarHerbert Xu <herbert@gondor.apana.org.au>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      225f4005
    • David S. Miller's avatar
    • Yitchak Gertner's avatar
      bnx2x: EEH recovery fix · f8ef6e44
      Yitchak Gertner authored
      When EEH detects an i/o error it resets the device thus it cannot be accessed.
      In this case the driver needs to unload its interface only with OS, kernel and
      network stack but not with the device.
      After successful recovery, the driver can load normally.
      Signed-off-by: default avatarYitchak Gertner <gertner@broadcom.com>
      Signed-off-by: default avatarEilon Greenstein <eilong@broadcom.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      f8ef6e44
    • Gerrit Renker's avatar
      This reverts "Merge branch 'dccp' of git://eden-feed.erg.abdn.ac.uk/dccp_exp" · 410e27a4
      Gerrit Renker authored
      as it accentally contained the wrong set of patches. These will be
      submitted separately.
      Signed-off-by: default avatarGerrit Renker <gerrit@erg.abdn.ac.uk>
      410e27a4
    • David S. Miller's avatar
    • Marcel Holtmann's avatar
      [Bluetooth] Reject L2CAP connections on an insecure ACL link · e7c29cb1
      Marcel Holtmann authored
      The Security Mode 4 of the Bluetooth 2.1 specification has strict
      authentication and encryption requirements. It is the initiators job
      to create a secure ACL link. However in case of malicious devices, the
      acceptor has to make sure that the ACL is encrypted before allowing
      any kind of L2CAP connection. The only exception here is the PSM 1 for
      the service discovery protocol, because that is allowed to run on an
      insecure ACL link.
      
      Previously it was enough to reject a L2CAP connection during the
      connection setup phase, but with Bluetooth 2.1 it is forbidden to
      do any L2CAP protocol exchange on an insecure link (except SDP).
      
      The new hci_conn_check_link_mode() function can be used to check the
      integrity of an ACL link. This functions also takes care of the cases
      where Security Mode 4 is disabled or one of the devices is based on
      an older specification.
      Signed-off-by: default avatarMarcel Holtmann <marcel@holtmann.org>
      e7c29cb1
    • Marcel Holtmann's avatar
      [Bluetooth] Enforce correct authentication requirements · 09ab6f4c
      Marcel Holtmann authored
      With the introduction of Security Mode 4 and Simple Pairing from the
      Bluetooth 2.1 specification it became mandatory that the initiator
      requires authentication and encryption before any L2CAP channel can
      be established. The only exception here is PSM 1 for the service
      discovery protocol (SDP). It is meant to be used without any encryption
      since it contains only public information. This is how Bluetooth 2.0
      and before handle connections on PSM 1.
      
      For Bluetooth 2.1 devices the pairing procedure differentiates between
      no bonding, general bonding and dedicated bonding. The L2CAP layer
      wrongly uses always general bonding when creating new connections, but it
      should not do this for SDP connections. In this case the authentication
      requirement should be no bonding and the just-works model should be used,
      but in case of non-SDP connection it is required to use general bonding.
      
      If the new connection requires man-in-the-middle (MITM) protection, it
      also first wrongly creates an unauthenticated link key and then later on
      requests an upgrade to an authenticated link key to provide full MITM
      protection. With Simple Pairing the link key generation is an expensive
      operation (compared to Bluetooth 2.0 and before) and doing this twice
      during a connection setup causes a noticeable delay when establishing
      a new connection. This should be avoided to not regress from the expected
      Bluetooth 2.0 connection times. The authentication requirements are known
      up-front and so enforce them.
      
      To fulfill these requirements the hci_connect() function has been extended
      with an authentication requirement parameter that will be stored inside
      the connection information and can be retrieved by userspace at any
      time. This allows the correct IO capabilities exchange and results in
      the expected behavior.
      Signed-off-by: default avatarMarcel Holtmann <marcel@holtmann.org>
      09ab6f4c
    • Marcel Holtmann's avatar
      [Bluetooth] Fix reference counting during ACL config stage · f1c08ca5
      Marcel Holtmann authored
      The ACL config stage keeps holding a reference count on incoming
      connections when requesting the extended features. This results in
      keeping an ACL link up without any users. The problem here is that
      the Bluetooth specification doesn't define an ownership of the ACL
      link and thus it can happen that the implementation on the initiator
      side doesn't care about disconnecting unused links. In this case the
      acceptor needs to take care of this.
      Signed-off-by: default avatarMarcel Holtmann <marcel@holtmann.org>
      f1c08ca5