This removes few unwanted headers related to irq, interrupt, regulator,
spinlock, etc.

Also arrange the rest in alphabetical order to make it more readable.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

wake_detect_gpio and resetn_gpio are guaranteed to be valid in
apb_ctrl_cleanup() and irq-handler, no need to check for their validity.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Relying on apb_ctrl_cleanup() to do the cleanup for errors that occurred
within apb_ctrl_init_seq() isn't a very clean idea. Handle that
separately within apb_ctrl_init_seq().

This will clean apb_ctrl_cleanup() in later patches.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

If devm_gpio_request() returns an error, we shouldn't try to set the
direction of the same gpio.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Use dev_err for errors after which we need to abort the currently
running routine and dev_warn for resource allocation failure, with which
we can continue to work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Since NULL could in theory be a valid regulator we ought to check for
IS_ERR() rather than for NULL. In practice this is unlikely to be an
issue but it's better for neatness.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

And so we don't need to check for it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

There can be no invalid values in the DTS. The actual pin numbers are
assigned by gpiolib when the gpio controller is registered.

And so a simple 'gpio < 0' is enough instead of gpio_is_valid() which
also checks for 'gpio < ARCH_NR_GPIOS'.

This will make the usage of of_get_named_gpio() similar with how it is
done in arche-platform driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Platform data 'apb' is guaranteed to be valid in arche_apb_ctrl_remove()
and so no need to check it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

- s/premits/permits
- Remove blank lines at the end of the file
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Propagate errors returned by of_get_named_gpio() instead of sending
-ENODEV.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

svc_reset_gpio is guaranteed to be valid in arche_platform_cleanup. Drop
the useless check.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

The current implementation around of_platform_populate() is not so
great. On error, we first print an error message, followed by a success
message and finally we return an error.

And over that we don't undo what we did initially.

This patch puts the APB back into reset and create a separate error
path to make things clear.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Populating APBs operation can potentially fail and it would be better if
we export the GPIOs towards then end of the routine, so that we don't
need to unexport them on error cases.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

arche_pdata is guaranteed to be valid in arche_platform_remove().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

The bootrom protocol issues no dynamic debugging messages when it functions
successfully.  Use dev_dbg() to fix that by issuing kernel logs when firmware
download works.
Signed-off-by: Eli Sennesh <esennesh@leaflabs.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Use the host device and connection name when logging errors as the
version-request helper must not assume that all connection have a
bundle.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

The bus code should only match bundle devices for now, and must not
assume all greybus devices are bundles.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Add missing bus type to driver structure when registering a greybus
driver.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Add greybus driver-data accessors.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Add support for the flags field of the stream configure request that was
recently added to the camera protocol and update the debugfs arguments
parsing accordingly. The stream configure response layout is also
updated to the latest protocol specification.
Signed-off-by: Jacopo Mondi <jacopo.mondi@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

The link config operation was a hack only designed to fulfill the camera
driver's needs. Now that a standard operation is defined for the same
purpose, implement it and remove the hack.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

With addition of handshaking between AP <=> SVC, driver
brings out APB out of reset only on reception of WAKE_MOD
signal from SVC. So remove the deassertion from probe.
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

This patch enables handshaking of AP and SVC using wake_detect
gpio (WD_8A and WD_8B).
Note that WAKE_DETECT polarity is active-high, so in order to
enable handshaking between AP <=> SVC, we need to set wake_detect
gpio to low initially, so that driver can send WAKE_DET signal
(active-high) to SVC and then SVC can send back WAKE_MOD signal
(active-low).
And on reception of WAKE_MOD signal, driver would bring respective
APB out of reset.

  WD_8A => APB1
  WD_8B => APB2
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

In order to allow user to flash the firmware to,

SVC:
user need to assert the reset first, set sysboot pin and
deassert reset. And then issue a flashing command.

And APB:
User need to assert the reset first, and then issue flashing
command.

So this patch exports the gpio's to user.
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Use 4 lanes at 960MHz to support camera modules requiring higher
bandwidths until we implement support for dynamic bandwidth calculation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

No need to have two separate arche platform drivers, that's just crazy,
so merge them both together to be only one kernel module.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Tested-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>

It seems we need to delete platform_dev of all childs explicitly,
in _remove() fn callback of parent driver.
There were some discussions about having of_platform_unpopulate(),
but it never made it to mainline.

https://lkml.org/lkml/2013/7/19/615

There are some drivers which are removing platform_dev explicitly,
as done in this patch.

Note that, without this, multiple insmod-rmmod won't work, as I see
driver probe gets invoked twice and leads to failure of probe.
Signed-off-by: Vaibhav Hiremath <hiremath_vaibhav@projectara.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Make sure to tear down the data connection also on failure to configure
the link by setting the data_connected flag immediately after creating
the connection.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Fix memory leak in capture-request handler by making sure to release the
operation request buffer after sending the request.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Fix memory leak in configure-streams error path by making sure to
release the operation buffers before returning.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

The version of the currently running firmware on the module is useful
for userspace as it can be used to find if an update is available or
not. This patch fetches interface's version with a new control operation
and exposes the same in userspace.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Two exactly same modules can be uniquely identified using module's
serial-number. This patch updates the interface hotplug event to also
receive the serial-number of the module.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

gb_svc_read_and_clear_module_boot_status() relies on the values of
ddbl1_manufacturer_id and ddbl1_product_id to distinguish between ES2
and ES3 chips, but those values are set for the interface structure only
after gb_svc_read_and_clear_module_boot_status() is called.

This makes ES2 module to fail with following errors:

greybus 1-2: Module not ready yet
greybus 1-svc: failed to clear boot status of interface 2: -19

Fix this by setting these values before calling
gb_svc_read_and_clear_module_boot_status().

Fixes: 51f1dc421b1f ("firmware and svc: detect the difference between ES2 and ES3 chips")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

The greybus specification reserves SVC type 0x0d-0x0f for timesync.
53124d73 ('svc: Add support for the link config operation') allocated the
next available type 0x0d which conflicts with the specification. Change the
type to 0x10 to ensure kernel and specification agree.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

We already have macro's defined for this, use them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Until we have proper handshake mechanism implemented with SVC
assert reset to APB at the end of probe.
We are safe here to do that, as SVC always enables clock to APB's
currently.
And also from EVT1 perspective, we should be good, as clock control
signals are now moved to AP.
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

It was messy to integrate both SVC, APB (and any other arche
platform specific control) into one single driver. Especially
due to cross-dependency.

AP first needs to bringup SVC, as SVC should enable clock to APB.
APB should come up before HUB, as due to some reason HUB wouldn't
enumerate APB's is APB comes up later.
And on top of that we should have clean picture of hardware description
in DT file.

So this patch introduces APB control driver. Mostly copied from original
arche-platform driver + fixed boot sequence.
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

With multiple platforms getting rolled into ara,
db3 name is confusing. And this driver is applicable
to all arche platforms, so make sense to rename it to
arche-platform.c. Also rename all internal functions
accordingly.
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Current db3(arche)-platform driver was only handling APB control signals,
which is where it all started. But now with completion of DB3/EVT1 bringup
we know that platform driver is more than APB control.

We have to bring SVC up before APB, as SVC supposed to enable
clock to APB's. Note that, in EVT1, AP will have direct control over
APB's clock.
Then we have dependency between APB and USB HUB, where, APB should be
brought up before USB HUB (note that this needs to rootcaused).

This patch cleanup the db3(arche)-platform driver to remove all APB control
code. The idea here is create another driver for APB control
(arche-apb-ctrl.c), which will deal with APB.
And this driver will have generic/common platform specific support,
currently manages SVC resources.

This patch also takes in all the changes from factory branch, discovered
during bringup.
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>