- 24 Jul, 2016 5 commits
-
-
William Breathitt Gray authored
The Measurement Computing CIO-DAC is a family of 16-bit and 12-bit analog output devices. The analog outputs are from AD660BN/AD7237 converters with each output buffered by an OP-27. Voltage ranges are configured via physical jumpers on the device. This driver does not support the devices' simulataneous update mode; the XFER jumper option should be deselected for all analog output channels. This driver provides IIO support for the Measurement Computing CIO-DAC family: CIO-DAC16, CIO-DAC08, and PC104-DAC06. The base port addresses for the devices may be configured via the base array module parameter. Signed-off-by:
William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by:
Jonathan Cameron <jic23@kernel.org>
-
Alison Schofield authored
Replace the code that guarantees the device stays in direct mode with iio_device_claim_direct_mode() which does same. Signed-off-by:
Alison Schofield <amsfield22@gmail.com> Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by:
-
Alison Schofield authored
Replace the code that guarantees the device stays in direct mode with iio_device_claim_direct_mode() which does same. Signed-off-by:
-
Christophe Chapuis authored
On the Cube i9 tablet, the ACPI id for the Kionix kxcj9 accelerometer is "KIOX000A" (as can be seen in the DSDT of the Cube i9 tablet). It is the same accelerometer, so only adding the ACPI id is needed. Signed-off-by:
Christophe Chapuis <chris.chapuis@gmail.com> Reviewed-by:
Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by:
-
Alison Schofield authored
I2C_CLASS_HWMON is for a hardware monitoring chip wanting auto-detection. IIO drivers don't typically use .class. Remove it. Signed-off-by:
Laxman Dewangan <ldewangan@nvidia.com> Acked-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
- 10 Jul, 2016 14 commits
-
-
Peter Meerwald-Stadler authored
Signed-off-by:
Peter Meerwald-Stadler <pmeerw@pmeerw.net> Signed-off-by:
-
Peter Meerwald-Stadler authored
Signed-off-by:
-
Peter Meerwald-Stadler authored
Signed-off-by:
-
Peter Meerwald-Stadler authored
and drop unused PROX_DRIVE Signed-off-by:
-
Peter Meerwald-Stadler authored
Signed-off-by:
-
Peter Meerwald-Stadler authored
Signed-off-by:
-
Peter Meerwald-Stadler authored
Signed-off-by:
-
Peter Meerwald-Stadler authored
Signed-off-by:
-
Peter Meerwald-Stadler authored
Signed-off-by:
-
Peter Meerwald-Stadler authored
Signed-off-by:
-
Peter Meerwald-Stadler authored
Signed-off-by:
-
Peter Meerwald-Stadler authored
Signed-off-by:
-
Peter Meerwald-Stadler authored
VCNL4000, VCNL4010 and VCNL4020 chips are fairly compatible from a software point of view, added features are not yet supported by the driver patch adds a check for the product ID and demotes the corresponding dev_info() to dev_dbg() Signed-off-by:
-
Matt Ranostay authored
Add initial driver support for MAX6675, and MAX31855 thermocouple chips. Cc: Marek Vasut <marex@denx.de> Cc: Matt Porter <mporter@konsulko.com> Signed-off-by:
Matt Ranostay <mranostay@gmail.com> Signed-off-by:
-
- 05 Jul, 2016 2 commits
-
-
Bijosh Thykkoottathil authored
Removed unwanted return statements from the function mma8452_set_freefall_mode. Signed-off-by:
Bijosh Thykkoottathil <bijosh.t@hotmail.com> Acked-by:
Martin Kepplinger <martink@posteo.de> Signed-off-by:
-
Bijosh Thykkoottathil authored
mma8452_set_freefall_mode can return -ve value in case if i2c_smbus_read_byte_data fails. This function is called from mma8452_probe, and returning -ve value from probe indicates probe failure. Need to call iio_triggered_buffer_cleanup & iio_trigger_cleanup in this case. Signed-off-by:
-
- 04 Jul, 2016 10 commits
-
-
Jonathan Cameron authored
The tree has been in the same location for a long time. Putting it in MAINTAINERS makes it easy for those new to, or less familiar with IIO to find the correct tree to base patches on. Mostly basing on staging-next is fine as well unless working on a very active driver. Signed-off-by: -
Gregor Boirie authored
Some static channels are explicitly initialized with default values. Remove them to enhance readability. Signed-off-by:
Gregor Boirie <gregor.boirie@parrot.com> Tested-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Gregor Boirie authored
Implement lps22hb temperature sampling channel. Signed-off-by:
-
Gregor Boirie authored
Add support for open drain interrupt line. Signed-off-by:
-
Gregor Boirie authored
Enable support for triggered buffering of temperature samples. Signed-off-by:
-
Gregor Boirie authored
Details scaling factors and offsets applied to raw temperature and pressure samples. Signed-off-by:
-
Gregor Boirie authored
Sampled pressure data are 24 bits long and should be stored in a 32 bits word. Signed-off-by:
-
Gregor Boirie authored
Ensure triggered buffering memory accesses are properly aligned on per channel storagebits boundaries. Signed-off-by:
-
Jonathan Cameron authored
Retire this venerable driver as the basic support is now in the generic st-sensors accelerometer driver. There are a few missing features in the new driver: * Threshold events. * Access to the calibration adjustment registers (patch shortly) In exchange it brings a cleaner and more maintainable code base that actually gets tested more than once every few years. I'll actually be suprised if anyone other than me has a board with one of these on that is running an up to date kernel. Signed-off-by: -
Jonathan Cameron authored
Time to finally kill off the venerable (it was one of my first drivers) lis3l02dq driver in favour of adding support in the st sensors framework. This does loose us the event support that driver always had, but I think that will reappear at some point and in the meantime the maintenance advantages of dropping the 'special' driver for this one part outweigh the issues. It's worth noting this part is ancient and I may well be the only person who still has any on hardware running recent kernels. It has a few 'quirks'. - No WAI register so that just became optional. - A BDU option that really does block updates. Completely. Whatever you do, you don't get any more data with it set. It is documented the same as more modern parts but I presume they are actually clearing for updates after a read of both bytes! - Fixed scale. - It's too quick. Even at slowest rate (280Hz) I can't read out fast enough on my board (stargate 2) to beat new data coming in. Linus' repeat read patch doesn't help in this case. It just means I get 10 readings before dying... So in reality this will get used with software triggers only unless someone has this long out of production device on a quick board. Signed-off-by:
-
- 03 Jul, 2016 9 commits
-
-
Matt Ranostay authored
Adding missing indio_dev->dev.of_node references to allow iio consumers to access the device channels. Signed-off-by:
-
Matt Ranostay authored
Add the pointer to the device tree node of the ADC so that iio consumers can reference the respective channels. Signed-off-by:
Daniel Baluta <daniel.baluta@intel.com> Signed-off-by:
-
Florian Vaussard authored
Fix s/potentiomenter/potentiometer/. Suggested-by:
Florian Vaussard <florian.vaussard@heig-vd.ch> Signed-off-by:
-
Florian Vaussard authored
This patch adds the necessary device tree binding to allow DT probing of currently supported parts. Signed-off-by:
Peter Rosin <peda@axentia.se> Signed-off-by:
-
Florian Vaussard authored
Add the device tree documentation for all the supported parts. Apart the compatible string and standard I2C binding, no other binding is currently needed. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Florian Vaussard authored
This patch adds support for MCP454x, MCP456x, MCP464x and MCP466x parts. The main difference with currently supported parts (MCP453x and alike) is the addition of a non-volatile memory in order to recall the wiper setting at power-on. This feature is currently not supported and only the volatile memory is used to set the wiper. Signed-off-by:
-
Gregor Boirie authored
Introduce support for Invense ICM20608 IMU, a 6-axis motion tracking device that combines a 3-axis gyroscope and a 3-axis accelerometer: http://www.invensense.com/products/motion-tracking/6-axis/icm-20608-2Signed-off-by:
-
Florian Vaussard authored
This patch adds the necessary device tree binding to allow DT probing of currently supported parts. Signed-off-by:
-
Florian Vaussard authored
Add the device tree documentation for all the supported parts. Mandatory binding is the compatible string and the slave I2C address. Optional properties can be used to specify the Vcc / Vref regulators, as well as the IRQ line if available. Acked-by:
-
