OOPS on resume when the wireless adaptor is disabled during suspend was
introduced by "eeepc-laptop: read rfkill soft-blocked state on resume".

Unable to handle kernel NULL pointer dereference

Process s2disk
Tainted: G W
IP: klist_put

Call trace:
? klist_del
? device_del
? device_unregister
? pci_stop_dev
? pci_stop_bus
? pci_remove_device
? eeepc_rfkill_hotplug [eeepc_laptop]
? eeepc_hotk_resume [eeepc_laptop]
? acpi_device_resume
? device_resume
? hibernation_snapshot

It appears the PCI device is removed twice.  The eeepc_rfkill_hotplug()
call from the resume handler is racing against the call from the ACPI
notifier callback.  The ACPI notification is triggered by the resume
handler when it refreshes the value of CM_ASL_WLAN.

The fix is to serialize hotplug calls using a workqueue.

http://bugzilla.kernel.org/show_bug.cgi?id=13825Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Acked-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>

If the memory block size is zero, ignore it and don't do the memory hotplug
flowchart. Otherwise it will complain the following warning message:
  >System RAM resource 0 - ffffffffffffffff cannot be added
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

Don't treat the generic error as ACPI error code. Otherwise when the generic
code is returned, it will complain the following warning messag:
   >ACPI Exception (acpi_memhotplug-0171): UNKNOWN_STATUS_CODE,
		Cannot get acpi bus device [20080609]
   >ACPI: Cannot find driver data
   > ACPI Error (utglobal-0127): Unknown exception code: 0xFFFFFFED [20080609]
   > Pid: 85, comm: kacpi_notify Not tainted 2.6.27.19-5-default #1
     Call Trace:
     [<ffffffff8020da29>] show_trace_log_lvl+0x41/0x58
     [<ffffffff8049a3da>] dump_stack+0x69/0x6f
    .....

At the same time when the generic error code is returned, the ACPI_EXCEPTION
is replaced by the printk.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

On some machines, a software-initiated SMI causes corruption unless the
SMI runs on CPU 0.  An SMI can be initiated by any AML, but typically it's
done in GPE-related methods that are run via workqueues, so we can avoid
the known corruption cases by binding the workqueues to CPU 0.

References:
    http://bugzilla.kernel.org/show_bug.cgi?id=13751
    https://bugs.launchpad.net/bugs/157171
    https://bugs.launchpad.net/bugs/157691Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>

they were world readable.
Signed-off-by: Len Brown <len.brown@intel.com>

HBRV-based default selection of backlight control strategy didn't work
well, at least the X41 defines it but doesn't use it and I don't think
it will stop there.

Switch to a white/blacklist.  All models that have HBRV defined have
been included in the list, and initially all ATI GPUs will get
ECNVRAM, and the Intel GPUs will get UCMS_STEP.

Symptoms of incorrect backlight mode selection are:

1. Non-working backlight control through sysfs;

2. Backlight gets reset to the lowest level at every shutdown, reboot
   and when thinkpad-acpi gets unloaded;

This fixes a regression in 2.6.30, bugzilla #13826
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Reported-by: Tobias Diedrich <ranma+kernel@tdiedrich.de>
Cc: stable@kernel.org
Signed-off-by: Len Brown <len.brown@intel.com>

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>

The standard ACPI dock driver can handle the hotplug bays and docks of
the ThinkPads just fine (including batteries) as of 2.6.27, and the
code in thinkpad-acpi for the dock and bay subdrivers is currently
broken anyway...

Userspace needs some love to support the two-stage ejection nicely,
but it is simple enough to do through udev rules (you don't even need
HAL) so this wouldn't justify fixing the dock and bay subdrivers,
either.

That leaves warm-swap bays (_EJ3) support for thinkpad-acpi, as well
as support for the weird dock of the model 570, but since such support
has never left the "experimental" stage, it is also not a strong
enough reason to find a way to fix this code.

Users of ThinkPads with warm-swap bays are urged to request that _EJ3
support be added to the regular ACPI dock driver, if such feature is
indeed useful for them.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>

Currently, the ThinkPad-ACPI bay and dock drivers are completely
broken, and cause a NULL pointer derreference in kernel mode (and,
therefore, an OOPS) when they try to issue events (i.e. on dock,
undock, bay ejection, etc).

OTOH, the standard ACPI dock driver can handle the hotplug bays and
docks of the ThinkPads just fine (including batteries) as of 2.6.27.
In fact, it does a much better job of it than thinkpad-acpi ever did.

It is just not worth the hassle to find a way to fix this crap without
breaking the (deprecated) thinkpad-acpi dock/bay ABI.  This is old,
deprecated code that sees little testing or use.

As a quick fix suitable for -stable backports, mark the thinkpad-acpi
bay and dock subdrivers as BROKEN in Kconfig.  The dead code will be
removed by a later patch.

This fixes bugzilla #13669, and should be applied to 2.6.27 and later.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Reported-by: Joerg Platte <jplatte@naasa.net>
Cc: stable@kernel.org
Signed-off-by: Len Brown <len.brown@intel.com>

* 'for-linus' of git://oss.sgi.com/xfs/xfs:
  xfs: bump up nr_to_write in xfs_vm_writepage
  xfs: reduce bmv_count in xfs_vn_fiemap

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  io context: fix ref counting
  block: make the end_io functions be non-GPL exports
  block: fix improper kobject release in blk_integrity_unregister
  block: always assign default lock to queues
  mg_disk: Add missing ready status check on mg_write()
  mg_disk: fix issue with data integrity on error in mg_write()
  mg_disk: fix reading invalid status when use polling driver
  mg_disk: remove prohibited sleep operation

Merge branch 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  clocksource: Save mult_orig in clocksource_disable()

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
  mmc: orphan subsystem
  imxmmc: Remove unnecessary semicolons
  cb710: use SG_MITER_TO_SG/SG_MITER_FROM_SG
  sdhci: use SG_MITER_TO_SG/SG_MITER_FROM_SG
  lib/scatterlist: add a flags to signalize mapping direction

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: sound/aoa: Add kmalloc NULL tests
  ALSA: hda - Increase PCM stream name buf in patch_realtek.c
  sound: mpu401.c: Buffer overflow
  sound: aedsp16: Buffer overflow
  ALSA: hda: fix out-of-bound hdmi_eld.sad[] write
  ALSA: hda - Add quirk for Dell Studio 1555

To fix the common case where ->enable() does not set up
mult, make sure mult_orig is saved in mult on disable.

Also add comments to explain why we do this.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: johnstul@us.ibm.com
Cc: lethal@linux-sh.org
Cc: akpm@linux-foundation.org
LKML-Reference: <20090618152432.10136.9932.sendpatchset@rx1.opensource.se>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

I do not have the time to take care of this, so remove myself as
maintainer.
Signed-off-by: Pierre Ossman <pierre@ossman.eu>

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>

the code allready uses flush_kernel_dcache_page(). This patch updates the
driver to the recent sg API changes which require that either SG_MITER_TO_SG
or SG_MITER_FROM_SG is set. SG_MITER_TO_SG calls flush_kernel_dcache_page()
in sg_mitter_stop()
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Acked-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>

so the page will be flushed on unmap on ARCH which need it.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>

sg_miter_start() is currently unaware of the direction of the copy
process (to or from the scatter list). It is important to know the
direction because the page has to be flushed in case the data written
is seen on a different mapping in user land on cache incoherent
architectures.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>

* fix/oss:
  sound: mpu401.c: Buffer overflow
  sound: aedsp16: Buffer overflow

* fix/misc:
  ALSA: sound/aoa: Add kmalloc NULL tests

* fix/hda:
  ALSA: hda - Increase PCM stream name buf in patch_realtek.c
  ALSA: hda: fix out-of-bound hdmi_eld.sad[] write
  ALSA: hda - Add quirk for Dell Studio 1555

Check that the result of kzalloc is not NULL before a dereference.

The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
expression *x;
identifier f;
constant char *C;
@@

x = \(kmalloc\|kcalloc\|kzalloc\)(...);
... when != x == NULL
    when != x != NULL
    when != (x || ...)
(
kfree(x)
|
f(...,C,...,x,...)
|
*f(...,x,...)
|
*x->f
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The name buf with size 16 is too short for some codec names, e.g.
truncated like "ALC861-VD Analo".  Now the size is doubled.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Commit d9c7d394
("block: prevent possible io_context->refcount overflow") mistakenly
changed atomic_inc(&ioc->nr_tasks) to atomic_long_inc(&ioc->refcount).
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Nikanth Karthikesan <knikanth@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>

VM calculation for nr_to_write seems off.  Bump it way
up, this gets simple streaming writes zippy again.
To be reviewed again after Jens' writeback changes.
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Cc: Chris Mason <chris.mason@oracle.com>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>

commit 6321e3ed caused
the full bmv_count's worth of getbmapx structures to get
allocated; telling it to do MAXEXTNUM was a bit insane,
resulting in ENOMEM every time.

Chop it down to something reasonable, the number of slots
in the caller's input buffer.  If this is too large the
caller may get ENOMEM but the reason should not be a
mystery, and they can try again with something smaller.

We add 1 to the value because in the normal getbmap
world, bmv_count includes the header and xfs_getbmap does:

        nex = bmv->bmv_count - 1;
        if (nex <= 0)
                return XFS_ERROR(EINVAL);
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Reviewed-by: Olaf Weber <olaf@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Felix Blyakher <felixb@sgi.com>

Merge branch 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  tracing/stat: Fix seqfile memory leak
  function-graph: Fix seqfile memory leak
  trace_stack: Fix seqfile memory leak
  profile: Suppress warning about large allocations when profile=1 is specified

* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
  Btrfs: be more polite in the async caching threads
  Btrfs: preserve commit_root for async caching

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
  dmaengine: at_hdmac: add DMA slave transfers
  dmaengine: at_hdmac: new driver for the Atmel AHB DMA Controller
  dmaengine: dmatest: correct thread_count while using multiple thread per channel
  dmaengine: dmatest: add a maximum number of test iterations
  drivers/dma: Remove unnecessary semicolons
  drivers/dma/fsldma.c: Remove unnecessary semicolons
  dmaengine: move HIGHMEM64G restriction to ASYNC_TX_DMA
  fsldma: do not clear bandwidth control bits on the 83xx controller
  fsldma: enable external start for the 83xx controller
  fsldma: use PCI Read Multiple command

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-udf-2.6:
  udf: Fix loading of VAT inode when drive wrongly reports number of recorded blocks