The dtl1_hci_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The btuart_hci_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The bt3c_hci_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The bluecard_hci_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The bfusb_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The legacy ioctls for device specific commands including inquiry are
not support by AMP controllers. So just reject them right away instead
of trying to send the HCI command and wait for failure from the
actual hardware.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

When changing the alternate setting for the ISOC endpoints, use the
hci_conn_num() helper function to count currently established SCO
and eSCO connections and store the the value. This avoids direct
access to the connection hash.

In addition use the stored value instead accessing the connection
hash over and over again.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

When checking for the current number of LE connections, use
hci_conn_num() function instead of a full blown lookup within
the connection hash or direct access of the counters.

In the case of re-enabling advertising, it is more useful to
check for any connection attempt or existing connection.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The function declaration goes over 80 characters, so break it down.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

When the HCI_SETUP flag is set the controller has not yet been announced
over mgmt and therefore doesn't exist from that perspective. If we
nevertheless get a mgmt command for it we should respond with the
appropriate INVALID_INDEX error.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The l2cap_recv_frame function is expected to take ownership and
eventually free the skb passed to it. We need to ensure that the
conn->rx_skb pointer is no longer reachable when calling
l2cap_recv_frame so that no other function, such as l2cap_conn_del, may
think that it can free conn->rx_skb.

An actual situation when this can happen is when smp_sig_channel (called
from l2cap_recv_frame) fails and l2cap_conn_del gets called as a
consequence. The l2cap_conn_del function would then try to free
conn->rx_skb, but as the same skb was just passed to smp_sig_channel and
freed we get a double-free.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The support for Bluetooth High Speed can only be enabled on controllers
where also Secure Simple Pairing has been enabled. Trying to enable
high speed when SSP is disabled will result into an error. Disabling
SSP will at the same time disable high speed as well.

It is required to enforce this dependency on SSP since high speed
support is only defined for authenticated, unauthenticated and
debug link keys. These link key types require SSP.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The variable val in the set_ssp() function of the management interface
is not needed. Just use cp->val directly since its input values have
already been validated.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

This patch does some code refactoring in hci_connect_le() by moving
the exception code into if statements and letting the main flow in
first level of function scope. It also adds extra comments to improve
the code readability.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch introduces a new helper, which uses the HCI request
framework, for creating LE connectons. All the handling is now
done by this function so we can remove the hci_cs_le_create_conn()
event handler.

This patch also removes the old hci_le_create_connection() since
it is not used anymore.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

We only (re)enable advertising when LE is disconnected. Trying to enable
advertising using mgmt_set_advertising while connected should simply
change the flag but not do anything else (until the connection gets
dropped). This patch fixes this by making an LE connection lookup to
determine whether there are any connected devices or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Sparse points out three places where variables are shadowed,
rename two of the variables and remove the duplicate third.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

When initializing an AMP controller, read its current flow control
mode so that the correct value is used.

The AMP controller defaults to block based flow control and this
extra command is just to double check.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

When initializing an AMP controller, read its current known location
data so that it can be analyzed later on.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The commands for reading supported features and commands are both
supported by AMP controllers. Issue them during controller init
phase so their values are known.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Within the AMP discover response, list powered down AMP controllers
as powered down. No point in trying to make them look any different.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The management interface only operates on BR/EDR controllers. The check
for the power down notification is a bit intermixed with the check if
controller auto power off is active. Since there are more than just
BR/EDR controllers supported, make this check explicit since the auto
power off check also applies to AMP controllers and it has to happen
in this exact order. Otherwise the bit will not be cleared.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Even AMP controllers should be powered off after the setup phase. It
is not a good idea to keep AMP controllers powered on all the time
if they are not in use.

Power on of the AMP controller can either be done manually via
command line commands or directly via A2MP. Especially since there
is an indication in A2MP for powered down controllers that can
be activated.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The return value of mgmt_discovering() function is not used
and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The return value of mgmt_remote_name() function is not used
and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The return value of mgmt_device_found() function is not used
and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The return value of mgmt_device_disconnected() function is not used
and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The return value of mgmt_device_connected() function is not used
and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The return value of mgmt_connect_failed() function is not used
so change it to just return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The return value of mgmt_disconnect_failed() function is not used
so change it to just return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The return value of mgmt_set_powered_failed() function is never used
and so make the function just return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The return value from mgmt_index_added() and mgmt_index_removed()
functions is never used. So do not pretend that returning an error
would actually be handled and just make both functions return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

In case the current value of pairable is already configured, do not
send a new settings event indicating that something has changed while
in reality everything is the same.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The helper function mgmt_valid_hdev() is more obfuscating the code
then it makes it easier to read. So intead of this helper, use the
direct check for BR/EDR device type.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The mgmt_new_settings() function was only needed to handle the
error case when re-enabling advertising failed. Since that is
now handled internally inside the management core, this function
is not needed anymore. So just remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

When the all LE connections have been disconneted, then it is up to
the host to re-enable advertising at that point. To ensure that the
correct advertising parameters are used, force the usage of the
common helper to enable advertising.

The change just moves the manual enabling of advertising from the
event handler into the management core so that the helper can
be actually shared.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The LE advertising parameters can only be modified when advertising
is disabled. So before enabling it, make sure the controller has all
the right parameters.

Right now all default values are used and thus this does no change
any existing behavior. One minor exception is that in case of single
mode LE-only controllers without a public address, now the random
address is used for advertising.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Add constants for ADV_IND, ADV_DIRECT_IND, ADV_SCAN_IND and
ADV_NONCONN_IND advertising types.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The tasks of enabling and disabling advertising are required in many
cases. So refactor the actual HCI operations into two common helpers
to make the code simpler.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

This is not a functional change, just change the code to make it easy
to understand that advertising gets disabled before LE support will
be turned off.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>