fix:
arch/x86/kernel/ds.c: In function ‘ds_allocate_buffer':
arch/x86/kernel/ds.c:339: error: implicit declaration of function ‘PAGE_ALIGN'
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Conflicts:

	arch/x86/Kconfig.cpu
	arch/x86/kernel/cpu/intel.c
	arch/x86/kernel/setup_64.c
Signed-off-by: Ingo Molnar <mingo@elte.hu>

This fixes the following compile error caused by commit
f9247273 ("UFS: add const to parser
token table"):

    CC      fs/nfs/nfsroot.o
  /home/bunk/linux/kernel-2.6/git/linux-2.6/fs/nfs/nfsroot.c:130: error: tokens causes a section type conflict
  make[3]: *** [fs/nfs/nfsroot.o] Error 1
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

..otherwise oprofile will fall back on that poor timer interrupt.

Also replace the unreadable chain of if-statements with a "switch()"
statement instead. It generates better code, and is a lot clearer.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Suresh Siddha wants to fix a possible FPU leakage in error conditions,
but the fact that save/restore_i387() are inlines in a header file makes
that harder to do than necessary.  So start off with an obvious cleanup.

This just moves the x86-64 version of save/restore_i387() out of the
header file, and moves it to the only file that it is actually used in:
arch/x86/kernel/signal_64.c.  So exposing it in a header file was wrong
to begin with.

[ Side note: I'd like to fix up some of the games we play with the
  32-bit version of these functions too, but that's a separate
  matter.  The 32-bit versions are shared - under different names
  at that! - by both the native x86-32 code and the x86-64 32-bit
  compatibility code ]
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (76 commits)
  ide: use proper printk() KERN_* levels in ide-probe.c
  ide: fix for EATA SCSI HBA in ATA emulating mode
  ide: remove stale comments from drivers/ide/Makefile
  ide: enable local IRQs in all handlers for TASKFILE_NO_DATA data phase
  ide-scsi: remove kmalloced struct request
  ht6560b: remove old history
  ht6560b: update email address
  ide-cd: fix oops when using growisofs
  gayle: release resources on ide_host_add() failure
  palm_bk3710: add UltraDMA/100 support
  ide: trivial sparse annotations
  ide: ide-tape.c sparse annotations and unaligned access removal
  ide: drop 'name' parameter from ->init_chipset method
  ide: prefix messages from IDE PCI host drivers by driver name
  it821x: remove DECLARE_ITE_DEV() macro
  it8213: remove DECLARE_ITE_DEV() macro
  ide: include PCI device name in messages from IDE PCI host drivers
  ide: remove <asm/ide.h> for some archs
  ide-generic: remove ide_default_{io_base,irq}() inlines (take 3)
  ide-generic: is no longer needed on ppc32
  ...

* 'release-2.6.27' of git://git.kernel.org/pub/scm/linux/kernel/git/ak/linux-acpi-2.6:
  acpi: fix crash in core ACPI code, triggered by CONFIG_ACPI_PCI_SLOT=y
  ACPI: thinkpad-acpi: don't misdetect in get_thinkpad_model_data() on -ENOMEM
  ACPI: thinkpad-acpi: bump up version to 0.21
  ACPI: thinkpad-acpi: add bluetooth and WWAN rfkill support
  ACPI: thinkpad-acpi: WLSW overrides other rfkill switches
  ACPI: thinkpad-acpi: prepare for bluetooth and wwan rfkill support
  ACPI: thinkpad-acpi: consolidate wlsw notification function
  ACPI: thinkpad-acpi: minor refactor on radio switch init
  Revert "ACPI: don't walk tables if ACPI was disabled"
  Revert "dock: bay: Don't call acpi_walk_namespace() when ACPI is disabled."
  Revert "Fix FADT parsing"
  ACPI : Set FAN device to correct state in boot phase
  ACPI: Ignore _BQC object when registering backlight device
  ACPI: stop complaints about interrupt link End Tags and blank IRQ descriptors

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  PCI: fixup sparse endianness warnings in proc.c
  PCI PM: make more PCI PM core functionality available to drivers
  PCI/DMAR: don't assume presence of RMRRs
  PCI hotplug: fix error path in pci_slot's register_slot

While at it:

- fixup printk() messages in save_match() and hwif_init().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

IDE probing code used to skip devices attached to EATA SCSI HBA
in ATA emulating mode but because of warm-plug support port I/O
resources are no longer freed if no devices are detected on a port
and the decision about the driver to use is left up to the user.

Remove no longer valid EATA SCSI HBA quirk from do_identify().
Noticed-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

It is already done by task_no_data_intr() and there is no reason
not to do it in other TASKFILE_NO_DATA data phase handlers.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This converts ide-scsi to use blk_get/put_request instead of
kmalloc/kfree.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Remove the ancient version history. Git does a better job.

From: Jan Evert van Grootheest <j.e.van.grootheest@caiway.nl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Update email address.

From: Jan Evert van Grootheest <j.e.van.grootheest@caiway.nl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

cdrom_read_capacity() will blindly return the capacity from the device
without sanity-checking it.  This later causes code in fs/buffer.c to
oops.

Fix this by checking that the device is telling us sensible things.

From: Jens Axboe <jens.axboe@oracle.com>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Jan Kara <jack@suse.cz>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: <stable@kernel.org>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[bart: print device name instead of driver name]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
[harvey: blocklen is a big-endian value]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

"gayle: reserve memory resources at once" patch temporary removed
freeing of resources on failure (to ease convertion to ide_host_add()
interface).  This patch fixes it.

Thanks to Geert for noticing the issue.
Noticed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This controller supports UltraDMA up to mode 5 but it should be clocked with
at least twice the data strobe frequency, so enable mode 5 for 100+ MHz IDECLK.

While at it, start passing the correct device to clk_get() -- it worked anyway
but WTF? :-/
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

If this is actually unaligned the access of speed/max_speed above
is already broken and needs a get_unaligned.  Otherwise it is
aligned and they can be removed.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Prefix messages from IDE PCI host drivers by driver name instead of marketed
chipset name (it is still possible to exactly identify the particular chipset
basing on driver messages).

As a bonus this provides nice code savings for some drivers:

   text    data     bss     dec     hex filename
   3826     112       8    3946     f6a drivers/ide/pci/amd74xx.o.before
   2786     112       8    2906     b5a drivers/ide/pci/amd74xx.o.after
    764     108       0     872     368 drivers/ide/pci/cs5520.o.before
    680     108       0     788     314 drivers/ide/pci/cs5520.o.after
   1680     112       4    1796     704 drivers/ide/pci/generic.o.before
   1155     112       4    1271     4f7 drivers/ide/pci/generic.o.after
   7128     792       0    7920    1ef0 drivers/ide/pci/hpt366.o.before
   6984     792       0    7776    1e60 drivers/ide/pci/hpt366.o.after
   2800     148       0    2948     b84 drivers/ide/pci/pdc202xx_new.o.before
   2523     148       0    2671     a6f drivers/ide/pci/pdc202xx_new.o.after
   2831     148       0    2979     ba3 drivers/ide/pci/pdc202xx_old.o.before
   2683     148       0    2831     b0f drivers/ide/pci/pdc202xx_old.o.after
   3776     112       4    3892     f34 drivers/ide/pci/piix.o.before
   2804     112       4    2920     b68 drivers/ide/pci/piix.o.after
   4693     116       0    4809    12c9 drivers/ide/pci/siimage.o.before
   4600     116       0    4716    126c drivers/ide/pci/siimage.o.after
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

While at it:

* it821x_chipsets[] -> it821x_chipset.

* Fix it821x_chipset's name field (as it is used for IT8211/8212).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

While at it:

* it8213_chipsets[] -> it8213_chipset.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

While at it:

* Apply small fixes to messages (s/dma/DMA/, remove trailing '.', etc).

* Fix printk() call in ide_setup_pci_baseregs() to use KERN_INFO.

* Move printk() call from ide_pci_clear_simplex() to the caller.

* Cleanup do_ide_setup_pci_device() a bit.

* amd74xx.c: remove superfluous PCI device revision information.

* hpt366.c: fix two printk() calls in ->init_chipset to use KERN_INFO.

* pdc202xx_new.c: fix printk() call in ->init_chipset to use KERN_INFO.

* pdc202xx_old.c: fix driver message in pdc202xx_init_one().

* via82cxxx.c: fix driver warning message in via_init_one().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Remove <linux/irq.h> include from <asm-ia64.h> (<linux/ide.h> includes
  <linux/interrupt.h> which is enough).

* Remove <asm/ide.h> for alpha/blackfin/h8300/ia64/m32r/sh/x86/xtensa
  (this leaves us with arm/frv/m68k/mips/mn10300/parisc/powerpc/sparc[64]).

There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Replace ide_default_{io_base,irq}() inlines by legacy_{bases,irqs}[].

v2:
Add missing zero-ing of hws[] (caught during testing by Borislav Petkov).

v3:
Fix zero-oing of hws[] for _real_ this time.

There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

PPC_PREP has been depending on BROKEN for some time now.

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Now that ide_hwif_t instances are allocated dynamically
  the difference between MAX_HWIFS == 2 and MAX_HWIFS == 10
  is ~100 bytes (x86-32) so use MAX_HWIFS == 10 on all archs
  except these ones that use MAX_HWIFS == 1.

* Define MAX_HWIFS in <linux/ide.h> instead of <asm/ide.h>.

[ Please note that avr32/cris/v850 have no <asm/ide.h>
  and alpha/ia64/sh always define CONFIG_IDE_MAX_HWIFS. ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Remove <asm-cris/arch-v{10,32}/ide.h> and <asm-cris/ide.h>.

This has been a broken code for some time now and needs rewrite
to match IDE core code / host driver model anyway.

Cc: Jesper Nilsson <Jesper.Nilsson@axis.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Since the decision to probe for ISA ide2-6 is now left to the user
"no_pci_devices()" quirk is no longer needed and may be removed.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Move ide_probe_legacy() call to ide_generic_init() so it fails
early if necessary and returns the proper error value (nowadays
ide_default_io_base() is used only by ide-generic).

Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fix ide_default_io_base() to match ide_default_irq().

Cc: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add missing <asm-generic/ide_iops.h> include.

While at it:

* Remove needless ide_default_{irq,io_base}() inlines.

Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>