The API was reduced to include only knowledge currently needed by the
FW scan logic, the rest is legacy.  Support the new, reduced version.

Using the old API with newer firmwares (starting from
iwlwifi-*-50.ucode, which implements and requires the new API version)
causes an assertion failure similar to this one:

[    2.854505] iwlwifi 0000:00:14.3: 0x20000038 | BAD_COMMAND
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mt76 dma layer is supposed to unmap skb data buffers while keep txwi
mapped on hw dma ring. At the moment mt76 wrongly unmap txwi or does
not unmap data fragments in even positions for non-linear skbs. This
issue may result in hw hangs with A-MSDU if the system relies on IOMMU
or SWIOTLB. Fix this behaviour properly unmapping data fragments on
non-linear skbs.

Fixes: 17f1de56 ("mt76: add common code shared between multiple chipsets")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

On same device (e.g. U7612E-H1) PCIE_ASPM causes continuous mcu hangs and
instability. Since mt76x2 series does not manage PCIE PS states, first we
try to disable ASPM using pci_disable_link_state. If it fails, we will
disable PCIE PS configuring PCI registers.
This patch has been successfully tested on U7612E-H1 mini-pice card
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In commit 8020919a ("mac80211: Properly handle SKB with radiotap
only"), buffers whose length is too short cause a WARN_ON(1) to be
executed. This change exposed a fault in rtlwifi drivers, which is fixed
by regarding packets with skb->len <= FCS_LEN as though they are in error
and dropping them. The test is now annotated as likely.

Cc: Stable <stable@vger.kernel.org> # v5.0+
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

When converting the wrong qu configurations in an earlier commit, I
accidentally swapped 0x2720 and 0x30DC.  Instead of converting 0x2720,
I converted 0x30DC.  Undo 0x30DC and convert 0x2720.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Add a workaround that forces power gating to be enabled on integrated
22000 devices.  This improves power saving in certain situations.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

iwl_mvm_tvqm_enable_txq() can return an error, notably if unable
to allocate memory for the queue. Handle this error throughout,
avoiding storing the invalid value into a u16 which later leads
to a disable of an invalid queue ("queue 65524 not used", where
65524 is just -ENOMEM in a u16).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

A bunch of the entries for qnj were wrong.  The 9460 device doesn't
exist, so update them to 9461 and 9462.  There are still a bunch of
other occurrences of 9460, but that will be fixed separately.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Some entries for PCI ID 0x2720 were using iwl9260_2ac_cfg, but the
correct is to use iwl9260_2ac_cfg_soc.  Fix that.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Nicolas Waisman noticed that even though noa_len is checked for
a compatible length it's still possible to overrun the buffers
of p2pinfo since there's no check on the upper bound of noa_num.
Bound noa_num against P2P_MAX_NOA_NUM.
Reported-by: Nicolas Waisman <nico@semmle.com>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Two patches were sent out of order: one removed some conditions from
an if and the other moved the code elsewhere.  When sending the patch
that moved the code, an older version of the original code was moved,
causing the "make QnJ exclusive" code to be essentially undone.

Fix that by removing the inclusive conditions from the check again.

Fixes: 809805a8 ("iwlwifi: pcie: move some cfg mangling from trans_pcie_alloc to probe")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

(kvalo: cherry picked from commit 1340cc63 in
wireless-drivers-next to wireless-drivers as this a frequently reported
regression)

Bad latency is found on QCA988x, the issue was introduced by
commit 4504f0e5 ("ath10k: sdio: workaround firmware UART
pin configuration bug"). If uart_pin_workaround is false, this
change will set uart pin even if uart_print is false.

Tested HW: QCA9880
Tested FW: 10.2.4-1.0-00037

Fixes: 4504f0e5 ("ath10k: sdio: workaround firmware UART pin configuration bug")
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Merge tag 'iwlwifi-for-kalle-2019-10-09' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes

First batch of fixes intended for v5.4

* fix for an ACPI table parsing bug;
* a fix for a NULL pointer dereference in the cfg with specific
  devices;
* fix the rb_allocator;
* prevent multiple phy configuration with new devices;
* fix a race-condition in the rx queue;
* prevent a couple of memory leaks;
* fix initialization of 3168 devices (the infamous BAD_COMMAND bug);
* fix recognition of some newer systems with integrated MAC;

There were a bunch of devices with qu and jf that were loading the
configuration with pu and jf, which is wrong.  Fix them all
accordingly.  Additionally, remove 0x1010 and 0x1210 subsytem IDs from
the list, since they are obviously wrong, and 0x0044 and 0x0244, which
were duplicate.

Cc: stable@vger.kernel.org # 5.1+
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

We currently support two NICs in FW version 29, namely 7265D and 3168.
Out of these, only 7265D supports GEO SAR, so adjust the function that
checks for it accordingly.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes: f5a47fae ("iwlwifi: mvm: fix version check for GEO_TX_POWER_LIMIT support")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

In iwl_pcie_ctxt_info_gen3_init there are cases that the allocated dma
memory is leaked in case of error.

DMA memories prph_scratch, prph_info, and ctxt_info_gen3 are allocated
and initialized to be later assigned to trans_pcie. But in any error case
before such assignment the allocated memories should be released.

First of such error cases happens when iwl_pcie_init_fw_sec fails.
Current implementation correctly releases prph_scratch. But in two
sunsequent error cases where dma_alloc_coherent may fail, such
releases are missing.

This commit adds release for prph_scratch when allocation for
prph_info fails, and adds releases for prph_scratch and prph_info when
allocation for ctxt_info_gen3 fails.

Fixes: 2ee82402 ("iwlwifi: pcie: support context information for 22560 devices")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

In alloc_sgtable if alloc_page fails, the alocated table should be
released.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

We don't handle failures in the rb_allocator workqueue allocation
correctly. To fix that, move the code earlier so the cleanup is
easier and we don't have to undo all the interrupt allocations in
this case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

We got a crash in iwl_trans_pcie_get_cmdlen(), while the TFD was
being accessed to sum up the lengths.

We want to access the TFD here, which is the information for the
hardware. We always only allocate 32 buffers for the cmd queue,
but on newer hardware (using TFH) we can also allocate only a
shorter hardware array, also only 32 TFDs. Prior to the TFH, we
had to allocate a bigger TFD array but would make those point to
a smaller set of buffers.

Additionally, now max_tfd_queue_size is up to 65536, so we can
access *way* out of bounds of a really only 32-entry array, so
it crashes.

Fix this by making the TFD index depend on which hardware we are
using right now.

While changing the calculation, also fix it to not use void ptr
arithmetic, but cast to u8 * before.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Consider the following flow:
 1. Driver starts to sync the rx queues due to a delba.
    mvm->queue_sync_cookie=1.
    This rx-queues-sync is synchronous, so it doesn't increment the
    cookie until all rx queues handle the notification from FW.
 2. During this time, driver starts to sync rx queues due to nssn sync
    required.
    The cookie's value is still 1, but it doesn't matter since this
    rx-queue-sync is non-synchronous so in the notification handler the
    cookie is ignored.
    What _does_ matter is that this flow increments the cookie to 2
    immediately.
    Remember though that the FW won't start servicing this command until
    it's done with the previous one.
 3. FW is still handling the first command, so it sends a notification
    with internal_notif->sync=1, and internal_notif->cookie=0, which
    triggers a WARN_ONCE.

The solution for this race is to only use the mvm->queue_sync_cookie in
case of a synchronous sync-rx-queues. This way in step 2 the cookie's
value won't change so we avoid the WARN.

The commit in the "fixes" field is the first commit to introduce
non-synchronous sending of this command to FW.

Fixes: 3c514bf8 ("iwlwifi: mvm: add a loose synchronization of the NSSN across Rx queues")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

The PHY is initialized during device initialization, but devices with
the tx_siso_diversity flag set need to send PHY_CONFIGURATION_CMD first,
otherwise the PHY would be reinitialized, causing a SYSASSERT.

To fix this, use a bit that tells the FW not to complete the PHY
initialization before a PHY_CONFIGURATION_CMD is received.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

We can't check for the ACPI table revision validity in the same if
where we check if the package was read correctly, because we return
PTR_ERR(pkg) and if the table is not valid but the pointer is, we
would return a valid pointer as an error.  Fix that by moving the
table checks to a separate if and return -EINVAL if it's not valid.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

We copy cfg->trans to trans->trans_cfg at the very beginning, so don't
try to access it via cfg->trans anymore, because the cfg may be unset
in later cases.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

The driver does not use input subsystem so we do not need this header,
and it is being removed, so stop pulling it in.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Initialize last_reset variable to INITIAL_JIFFIES, otherwise it is not
possible to test H/W reset for first 5 minutes of system run.

Fixes: e403fa31 ("rt2x00: add restart hw")
Reported-and-tested-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Pull btrfs fixes from David Sterba:
 "A bunch of fixes that accumulated in recent weeks, mostly material for
  stable.

  Summary:

   - fix for regression from 5.3 that prevents to use balance convert
     with single profile

   - qgroup fixes: rescan race, accounting leak with multiple writers,
     potential leak after io failure recovery

   - fix for use after free in relocation (reported by KASAN)

   - other error handling fixups"

* tag 'for-5.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: qgroup: Fix reserved data space leak if we have multiple reserve calls
  btrfs: qgroup: Fix the wrong target io_tree when freeing reserved data space
  btrfs: Fix a regression which we can't convert to SINGLE profile
  btrfs: relocation: fix use-after-free on dead relocation roots
  Btrfs: fix race setting up and completing qgroup rescan workers
  Btrfs: fix missing error return if writeback for extent buffer never started
  btrfs: adjust dirty_metadata_bytes after writeback failure of extent buffer
  Btrfs: fix selftests failure due to uninitialized i_mode in test inodes

Pull csky updates from Guo Ren:
 "This round of csky subsystem just some fixups:

   - Fix mb() synchronization problem

   - Fix dma_alloc_coherent with PAGE_SO attribute

   - Fix cache_op failed when cross memory ZONEs

   - Optimize arch_sync_dma_for_cpu/device with dma_inv_range

   - Fix ioremap function losing

   - Fix arch_get_unmapped_area() implementation

   - Fix defer cache flush for 610

   - Support kernel non-aligned access

   - Fix 610 vipt cache flush mechanism

   - Fix add zero_fp fixup perf backtrace panic

   - Move static keyword to the front of declaration

   - Fix csky_pmu.max_period assignment

   - Use generic free_initrd_mem()

   - entry: Remove unneeded need_resched() loop"

* tag 'csky-for-linus-5.4-rc1' of git://github.com/c-sky/csky-linux:
  csky: Move static keyword to the front of declaration
  csky: entry: Remove unneeded need_resched() loop
  csky: Fixup csky_pmu.max_period assignment
  csky: Fixup add zero_fp fixup perf backtrace panic
  csky: Use generic free_initrd_mem()
  csky: Fixup 610 vipt cache flush mechanism
  csky: Support kernel non-aligned access
  csky: Fixup defer cache flush for 610
  csky: Fixup arch_get_unmapped_area() implementation
  csky: Fixup ioremap function losing
  csky: Optimize arch_sync_dma_for_cpu/device with dma_inv_range
  csky/dma: Fixup cache_op failed when cross memory ZONEs
  csky: Fixup dma_alloc_coherent with PAGE_SO attribute
  csky: Fixup mb() synchronization problem

Pull ARM SoC fixes from Olof Johansson:
 "A few fixes that have trickled in through the merge window:

   - Video fixes for OMAP due to panel-dpi driver removal

   - Clock fixes for OMAP that broke no-idle quirks + nfsroot on DRA7

   - Fixing arch version on ASpeed ast2500

   - Two fixes for reset handling on ARM SCMI"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
  ARM: aspeed: ast2500 is ARMv6K
  reset: reset-scmi: add missing handle initialisation
  firmware: arm_scmi: reset: fix reset_state assignment in scmi_domain_reset
  bus: ti-sysc: Remove unpaired sysc_clkdm_deny_idle()
  ARM: dts: logicpd-som-lv: Fix i2c2 and i2c3 Pin mux
  ARM: dts: am3517-evm: Fix missing video
  ARM: dts: logicpd-torpedo-baseboard: Fix missing video
  ARM: omap2plus_defconfig: Fix missing video
  bus: ti-sysc: Fix handling of invalid clocks
  bus: ti-sysc: Fix clock handling for no-idle quirks

Pull tracing fixes from Steven Rostedt:
 "A few more tracing fixes:

   - Fix a buffer overflow by checking nr_args correctly in probes

   - Fix a warning that is reported by clang

   - Fix a possible memory leak in error path of filter processing

   - Fix the selftest that checks for failures, but wasn't failing

   - Minor clean up on call site output of a memory trace event"

* tag 'trace-v5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  selftests/ftrace: Fix same probe error test
  mm, tracing: Print symbol name for call_site in trace events
  tracing: Have error path in predicate_parse() free its allocated memory
  tracing: Fix clang -Wint-in-bool-context warnings in IF_ASSIGN macro
  tracing/probe: Fix to check the difference of nr_args before adding probe

Pull more MMC updates from Ulf Hansson:
 "A couple more updates/fixes for MMC:

   - sdhci-pci: Add Genesys Logic GL975x support

   - sdhci-tegra: Recover loss in throughput for DMA

   - sdhci-of-esdhc: Fix DMA bug"

* tag 'mmc-v5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: host: sdhci-pci: Add Genesys Logic GL975x support
  mmc: tegra: Implement ->set_dma_mask()
  mmc: sdhci: Let drivers define their DMA mask
  mmc: sdhci-of-esdhc: set DMA snooping based on DMA coherence
  mmc: sdhci: improve ADMA error reporting

Move the static keyword to the front of declaration of
csky_pmu_of_device_ids, and resolve the following compiler
warning that can be seen when building with warnings
enabled (W=1):

arch/csky/kernel/perf_event.c:1340:1: warning:
  ‘static’ is not at beginning of declaration [-Wold-style-declaration]
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Guo Ren <guoren@kernel.org>

Since the enabling and disabling of IRQs within preempt_schedule_irq()
is contained in a need_resched() loop, we don't need the outer arch
code loop.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Guo Ren <guoren@kernel.org>

Pull Documentation/process update from Greg KH:
 "Here are two small Documentation/process/embargoed-hardware-issues.rst
  file updates that missed my previous char/misc pull request.

  The first one adds an Intel representative for the process, and the
  second one cleans up the text a bit more when it comes to how the
  disclosure rules work, as it was a bit confusing to some companies"

* tag 'char-misc-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  Documentation/process: Clarify disclosure rules
  Documentation/process: Volunteer as the ambassador for Intel

Pull more vfs updates from Al Viro:
 "A couple of misc patches"

* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  afs dynroot: switch to simple_dir_operations
  fs/handle.c - fix up kerneldoc

Pull more cifs updates from Steve French:
 "Fixes from the recent SMB3 Test events and Storage Developer
  Conference (held the last two weeks).

  Here are nine smb3 patches including an important patch for debugging
  traces with wireshark, with three patches marked for stable.

  Additional fixes from last week to better handle some newly discovered
  reparse points, and a fix the create/mkdir path for setting the mode
  more atomically (in SMB3 Create security descriptor context), and one
  for path name processing are still being tested so are not included
  here"

* tag '5.4-rc-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  CIFS: Fix oplock handling for SMB 2.1+ protocols
  smb3: missing ACL related flags
  smb3: pass mode bits into create calls
  smb3: Add missing reparse tags
  CIFS: fix max ea value size
  fs/cifs/sess.c: Remove set but not used variable 'capabilities'
  fs/cifs/smb2pdu.c: Make SMB2_notify_init static
  smb3: fix leak in "open on server" perf counter
  smb3: allow decryption keys to be dumped by admin for debugging

The csky_pmu.max_period has type u64, and BIT() can only return
32 bits unsigned long on C-SKY. The initialization for max_period
will be incorrect when count_width is bigger than 32.

Use BIT_ULL()
Signed-off-by: Mao Han <han_mao@c-sky.com>
Signed-off-by: Guo Ren <ren_guo@c-sky.com>

We need set fp zero to let backtrace know the end. The patch fixup perf
callchain panic problem, because backtrace didn't know what is the end
of fp.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Reported-by: Mao Han <han_mao@c-sky.com>

The csky implementation of free_initrd_mem() is an open-coded version of
free_reserved_area() without poisoning.

Remove it and make csky use the generic version of free_initrd_mem().
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Guo Ren <guoren@kernel.org>

Merge active entropy generation updates.

This is admittedly partly "for discussion".  We need to have a way
forward for the boot time deadlocks where user space ends up waiting for
more entropy, but no entropy is forthcoming because the system is
entirely idle just waiting for something to happen.

While this was triggered by what is arguably a user space bug with
GDM/gnome-session asking for secure randomness during early boot, when
they didn't even need any such truly secure thing, the issue ends up
being that our "getrandom()" interface is prone to that kind of
confusion, because people don't think very hard about whether they want
to block for sufficient amounts of entropy.

The approach here-in is to decide to not just passively wait for entropy
to happen, but to start actively collecting it if it is missing.  This
is not necessarily always possible, but if the architecture has a CPU
cycle counter, there is a fair amount of noise in the exact timings of
reasonably complex loads.

We may end up tweaking the load and the entropy estimates, but this
should be at least a reasonable starting point.

As part of this, we also revert the revert of the ext4 IO pattern
improvement that ended up triggering the reported lack of external
entropy.

* getrandom() active entropy waiting:
  Revert "Revert "ext4: make __ext4_get_inode_loc plug""
  random: try to actively add entropy rather than passively wait for it