Take two endpoints attached to the first switch on the first host-bridge
in the cxl_test topology and define a pre-initialized region. This is a
x2 interleave underneath a x1 CXL Window.

$ modprobe cxl_test
$ # cxl list -Ru
{
  "region":"region3",
  "resource":"0xf010000000",
  "size":"512.00 MiB (536.87 MB)",
  "interleave_ways":2,
  "interleave_granularity":4096,
  "decode_state":"commit"
}
Tested-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/167602000547.1924368.11613151863880268868.stgit@dwillia2-xfh.jf.intel.comSigned-off-by: Dan Williams <dan.j.williams@intel.com>

Region autodiscovery is an asynchronous state machine advanced by
cxl_port_probe(). After the decoders on an endpoint port are enumerated
they are scanned for actively enabled instances. Each active decoder is
flagged for auto-assembly CXL_DECODER_F_AUTO and attached to a region.
If a region does not already exist for the address range setting of the
decoder one is created. That creation process may race with other
decoders of the same region being discovered since cxl_port_probe() is
asynchronous. A new 'struct cxl_root_decoder' lock, @range_lock, is
introduced to mitigate that race.

Once all decoders have arrived, "p->nr_targets == p->interleave_ways",
they are sorted by their relative decode position. The sort algorithm
involves finding the point in the cxl_port topology where one leg of the
decode leads to deviceA and the other deviceB. At that point in the
topology the target order in the 'struct cxl_switch_decoder' indicates
the relative position of those endpoint decoders in the region.

>From that point the region goes through the same setup and validation
steps as user-created regions, but instead of programming the decoders
it validates that driver would have written the same values to the
decoders as were already present.
Tested-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/167601999958.1924368.9366954455835735048.stgit@dwillia2-xfh.jf.intel.comSigned-off-by: Dan Williams <dan.j.williams@intel.com>

Jonathan points out that the shared code between the switch and endpoint
case is small. Before adding another is_cxl_endpoint() conditional,
just split the two cases.

Rather than duplicate the "Couldn't enumerate decoders" error message
take the opportunity to improve the error messages in
devm_cxl_enumerate_decoders().
Reported-by: Jonathan Cameron <Jonathan.Cameron@Huawei.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/167601999378.1924368.15071142145866277623.stgit@dwillia2-xfh.jf.intel.comSigned-off-by: Dan Williams <dan.j.williams@intel.com>

Add help text and a label so the CXL_REGION config option can be
toggled. This is mainly to enable compile testing without region
support.
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Gregory Price <gregory.price@memverge.com>
Tested-by: Fan Ni <fan.ni@samsung.com>
Link: https://lore.kernel.org/r/167601998765.1924368.258370414771847699.stgit@dwillia2-xfh.jf.intel.comSigned-off-by: Dan Williams <dan.j.williams@intel.com>

In support of the CXL subsystem's use of 'struct range' to track decode
address ranges, add a common range_contains() implementation with
identical semantics as resource_contains();

The existing 'range_contains()' in lib/stackinit_kunit.c is namespaced
with a 'stackinit_' prefix.

Cc: Kees Cook <keescook@chromium.org>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Gregory Price <gregory.price@memverge.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Tested-by: Fan Ni <fan.ni@samsung.com>
Link: https://lore.kernel.org/r/167601998163.1924368.6067392174077323935.stgit@dwillia2-xfh.jf.intel.comSigned-off-by: Dan Williams <dan.j.williams@intel.com>

In preparation for region autodiscovery, that needs all devices
discovered before their relative position in the region can be
determined, consolidate all position dependent validation in a helper.

Recall that in the on-demand region creation flow the end-user picks the
position of a given endpoint decoder in a region. In the autodiscovery
case the position of an endpoint decoder can only be determined after
all other endpoint decoders that claim to decode the region's address
range have been enumerated and attached. So, in the autodiscovery case
endpoint decoders may be attached before their relative position is
known. Once all decoders arrive, then positions can be determined and
validated with cxl_region_validate_position() the same as user initiated
on-demand creation.
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Tested-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/167601997584.1924368.4615769326126138969.stgit@dwillia2-xfh.jf.intel.comSigned-off-by: Dan Williams <dan.j.williams@intel.com>

Jonathan noticed that the target list setup is not unwound completely
upon error. Undo all the setup in the 'err_decrement:' exit path.

Fixes: 27b3f8d1 ("cxl/region: Program target lists")
Reported-by: Jonathan Cameron <Jonathan.Cameron@Huawei.com>
Link: http://lore.kernel.org/r/20230208123031.00006990@Huawei.comReviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/167601996980.1924368.390423634911157277.stgit@dwillia2-xfh.jf.intel.comSigned-off-by: Dan Williams <dan.j.williams@intel.com>

Region autodiscovery is the process of kernel creating 'struct
cxl_region' object to represent active CXL memory ranges it finds
already active in hardware when the driver loads. Typically this happens
when platform firmware establishes CXL memory regions and then publishes
them in the memory map. However, this can also happen in the case of
kexec-reboot after the kernel has created regions.

In the autodiscovery case the region creation process starts with a
known endpoint decoder. Refactor attach_target() into a helper that is
suitable to be called from either sysfs, for runtime region creation, or
from cxl_port_probe() after it has enumerated all endpoint decoders.

The cxl_port_probe() context is an async device-core probing context, so
it is not appropriate to allow SIGTERM to interrupt the assembly
process. Refactor attach_target() to take @cxled and @state as arguments
where @state indicates whether waiting from the region rwsem is
interruptible or not.

No behavior change is intended.
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Fan Ni <fan.ni@samsung.com>
Link: https://lore.kernel.org/r/167601996393.1924368.2202255054618600069.stgit@dwillia2-xfh.jf.intel.comSigned-off-by: Dan Williams <dan.j.williams@intel.com>

Expand the region creation infrastructure to enable 'ram'
(volatile-memory) regions. The internals of create_pmem_region_store()
and create_pmem_region_show() are factored out into helpers
__create_region() and __create_region_show() for the 'ram' case to
reuse.
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Reviewed-by: Gregory Price <gregory.price@memverge.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Fan Ni <fan.ni@samsung.com>
Link: https://lore.kernel.org/r/167601995775.1924368.352616146815830591.stgit@dwillia2-xfh.jf.intel.comSigned-off-by: Dan Williams <dan.j.williams@intel.com>

In preparation for a new region mode, do not, for example, allow
'ram' decoders to be assigned to 'pmem' regions and vice versa.
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Reviewed-by: Gregory Price <gregory.price@memverge.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Fan Ni <fan.ni@samsung.com>
Link: https://lore.kernel.org/r/167601995111.1924368.7459128614177994602.stgit@dwillia2-xfh.jf.intel.comSigned-off-by: Dan Williams <dan.j.williams@intel.com>

Shipping versions of the cxl-cli utility expect all regions to have a
'uuid' attribute. In preparation for 'ram' regions, update the 'uuid'
attribute to return an empty string which satisfies the current
expectations of 'cxl list -R'. Otherwise, 'cxl list -R' fails in the
presence of regions with the 'uuid' attribute missing. Force the
attribute to be read-only as there is no facility or expectation for a
'ram' region to recall its uuid from one boot to the next.
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Tested-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/167601994558.1924368.12612811533724694444.stgit@dwillia2-xfh.jf.intel.comSigned-off-by: Dan Williams <dan.j.williams@intel.com>

In preparation for a new region type, "ram" regions, add a mode
attribute to clarify the mode of the decoders that can be added to a
region. Share the internals of mode_show() (for decoders) with the
region case.
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Gregory Price <gregory.price@memverge.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Fan Ni <fan.ni@samsung.com>
Link: https://lore.kernel.org/r/167601993930.1924368.4305018565539515665.stgit@dwillia2-xfh.jf.intel.comSigned-off-by: Dan Williams <dan.j.williams@intel.com>

Prior to Linus deciding that the kernel that following v5.19 would be
v6.0, the CXL ABI documentation already referenced v5.20. In preparation
for updating these entries update the kernel version to v6.0.
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Gregory Price <gregory.price@memverge.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Fan Ni <fan.ni@samsung.com>
Link: https://lore.kernel.org/r/167601993360.1924368.14122892663883462813.stgit@dwillia2-xfh.jf.intel.comSigned-off-by: Dan Williams <dan.j.williams@intel.com>

Testing of ram region support [1], stimulates a long standing bug in
cxl_detach_ep() where some cxl_ep_remove() cleanup is skipped due to
inability to walk ports after dports have been unregistered. That
results in a failure to re-register a memdev after the port is
re-enabled leading to a crash like the following:

    cxl_port_setup_targets: cxl region4: cxl_host_bridge.0:port4 iw: 1 ig: 256
    general protection fault, ...
    [..]
    RIP: 0010:cxl_region_setup_targets+0x897/0x9e0 [cxl_core]
    dev_name at include/linux/device.h:700
    (inlined by) cxl_port_setup_targets at drivers/cxl/core/region.c:1155
    (inlined by) cxl_region_setup_targets at drivers/cxl/core/region.c:1249
    [..]
    Call Trace:
     <TASK>
     attach_target+0x39a/0x760 [cxl_core]
     ? __mutex_unlock_slowpath+0x3a/0x290
     cxl_add_to_region+0xb8/0x340 [cxl_core]
     ? lockdep_hardirqs_on+0x7d/0x100
     discover_region+0x4b/0x80 [cxl_port]
     ? __pfx_discover_region+0x10/0x10 [cxl_port]
     device_for_each_child+0x58/0x90
     cxl_port_probe+0x10e/0x130 [cxl_port]
     cxl_bus_probe+0x17/0x50 [cxl_core]

Change the port ancestry walk to be by depth rather than by dport. This
ensures that even if a port has unregistered its dports a deferred
memdev cleanup will still be able to cleanup the memdev's interest in
that port.

The parent_port->dev.driver check is only needed for determining if the
bottom up removal beat the top-down removal, but cxl_ep_remove() can
always proceed given the port is pinned. That is, the two sources of
cxl_ep_remove() are in cxl_detach_ep() and cxl_port_release(), and
cxl_port_release() can not run if cxl_detach_ep() holds a reference.

Fixes: 2703c16c ("cxl/core/port: Add switch port enumeration")
Link: http://lore.kernel.org/r/167564534874.847146.5222419648551436750.stgit@dwillia2-xfh.jf.intel.com [1]
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Link: https://lore.kernel.org/r/167601992789.1924368.8083994227892600608.stgit@dwillia2-xfh.jf.intel.comSigned-off-by: Dan Williams <dan.j.williams@intel.com>

Similar to the justification in:

1b58b4ca ("cxl/port: Record parent dport when adding ports")

...userspace wants to know the routing information for ports for
calculating the memdev order for region creation among other things.
Cache the information the kernel discovers at enumeration time in a
'parent_dport' attribute to save userspace the time of trawling sysfs
to recover the same information.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/167124082375.1626103.6047000000121298560.stgit@dwillia2-xfh.jf.intel.comSigned-off-by: Dan Williams <dan.j.williams@intel.com>

Both cxl_switch_decoders() and cxl_endpoint_decoders() are considered by
cxl_region_decode_commit(). Flag cases where cxl_switch_decoders with
multiple targets, or cxl_endpoint_decoders do not have a commit callback
set. The switch case is unlikely to happen since switches are only
enumerated by the CXL core, but the endpoint case may support decoders
defined by drivers outside of drivers/cxl, like accerator drivers.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/167124081824.1626103.1555704405392757219.stgit@dwillia2-xfh.jf.intel.comSigned-off-by: Dan Williams <dan.j.williams@intel.com>

size_t is limited to 32-bits and so the gen_pool_alloc() using
the size of SZ_64G would map to 0, triggering a low allocation
which is not expected. Force the dependency on 64-bit for cxl_test
as that is what it was designed for.

This issue was found by build test reports when converting this
driver as a proper upstream driver.
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20221219195050.325959-1-mcgrof@kernel.orgSigned-off-by: Dan Williams <dan.j.williams@intel.com>

For debugging it is very helpful to see which commands are sent. Add
it to the debug message.
Signed-off-by: Robert Richter <rrichter@amd.com>
Link: https://lore.kernel.org/r/20230103210151.1126873-1-rrichter@amd.comSigned-off-by: Dan Williams <dan.j.williams@intel.com>

The cxl_test machinery builds modified versions of the modules in
drivers/cxl/ and intercepts some of their calls to allow cxl_test to
inject mock CXL topologies for test.

However, if cxl_test attempts the same with production modules,
fireworks ensue as Luis discovered [1]. Prevent that scenario by
arranging for cxl_test to check for a "watermark" symbol in each of the
modules it expects to be modified before the test can run. This turns
undefined runtime behavior or crashes into a safer failure to load the
cxl_test module.

Link: http://lore.kernel.org/r/20221209062919.1096779-1-mcgrof@kernel.org [1]
Reported-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

No need for more than once per module load.
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20221215183836.24136-1-dave@stgolabs.netSigned-off-by: Dan Williams <dan.j.williams@intel.com>

CXL _OSC Error Reporting Control is used by the OS to determine if
Firmware has control of various CXL error reporting capabilities
including the event logs.

Expose the result of negotiating CXL Error Reporting Control in struct
pci_host_bridge for consumption by the CXL drivers.

Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: linux-pci@vger.kernel.org
Cc: linux-acpi@vger.kernel.org
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/20221212070627.1372402-2-ira.weiny@intel.comSigned-off-by: Dan Williams <dan.j.williams@intel.com>

CXL is using tracepoints for reporting RAS capability register payloads
for AER events, and has plans to use tracepoints for the output payload
of Get Poison List and Get Event Records commands. For organization
purposes it would be nice to keep those all under a single + local CXL
trace system. This also organization also potentially helps in the
future when CXL drivers expand beyond generic memory expanders, however
that would also entail a move away from the expander-specific
cxl_dev_state context, save that for later.

Note that the powerpc-specific drivers/misc/cxl/ also defines a 'cxl'
trace system, however, it is unlikely that a single platform will ever
load both drivers simultaneously.

Cc: Steven Rostedt <rostedt@goodmis.org>
Tested-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/167051869176.436579.9728373544811641087.stgit@dwillia2-xfh.jf.intel.comSigned-off-by: Dan Williams <dan.j.williams@intel.com>

Pull perf fixes from Borislav Petkov:

 - Pass only an initialized perf event attribute to the LSM hook

 - Fix a use-after-free on the perf syscall's error path

 - A potential integer overflow fix in amd_core_pmu_init()

 - Fix the cgroup events tracking after the context handling rewrite

 - Return the proper value from the inherit_event() function on error

* tag 'perf_urgent_for_v6.2_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/core: Call LSM hook after copying perf_event_attr
  perf: Fix use-after-free in error path
  perf/x86/amd: fix potential integer overflow on shift of a int
  perf/core: Fix cgroup events tracking
  perf core: Return error pointer if inherit_event() fails to find pmu_ctx

Pull x86 fixes from Borislav Petkov:

 - Two fixes to correct how kprobes handles INT3 now that they're added
   by other functionality like the rethunks and not only kgdb

 - Remove __init section markings of two functions which are referenced
   by a function in the .text section

* tag 'x86_urgent_for_v6.2_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/kprobes: Fix optprobe optimization check with CONFIG_RETHUNK
  x86/kprobes: Fix kprobes instruction boudary check with CONFIG_RETHUNK
  x86/calldepth: Fix incorrect init section references

Pull locking fixes from Borislav Petkov:

 - Prevent the leaking of a debug timer in futex_waitv()

 - A preempt-RT mutex locking fix, adding the proper acquire semantics

* tag 'locking_urgent_for_v6.2_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  futex: Fix futex_waitv() hrtimer debug object leak on kcalloc error
  rtmutex: Add acquire semantics for rtmutex lock acquisition slow path

Pull drm fixes from Daniel Vetter:
 "I'm just back from the mountains, and Dave is out at the beach and
  should be back in a week again. Just i915 fixes and since Rodrigo
  bothered to make the pull last week I figured I should warm up gpg and
  forward this in a nice signed tag as a new years present!

   - i915 fixes for newer platforms

   - i915 locking rework to not give up in vm eviction fallback path too
     early"

* tag 'drm-fixes-2023-01-01' of git://anongit.freedesktop.org/drm/drm:
  drm/i915/dsi: fix MIPI_BKLT_EN_1 native GPIO index
  drm/i915/dsi: add support for ICL+ native MIPI GPIO sequence
  drm/i915/uc: Fix two issues with over-size firmware files
  drm/i915: improve the catch-all evict to handle lock contention
  drm/i915: Remove __maybe_unused from mtl_info
  drm/i915: fix TLB invalidation for Gen12.50 video and compute engines

Merge tag 'drm-intel-fixes-2022-12-30' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes

- fix TLB invalidation for DG2 and newer platforms. (Andrzej)
- Remove __maybe_unused from mtl_info (Lucas)
- improve the catch-all evict to handle lock contention (Matt Auld)
- Fix two issues with over-size (GuC/HuC) firmware files (John)
- Fix DSI resume issues on ICL+ (Jani)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/Y662ijDHrZCjTFla@intel.com

Merge tag 'kbuild-fixes-v6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - Fix broken BuildID

 - Add srcrpm-pkg to the help message

 - Fix the option order for modpost built with musl libc

 - Fix the build dependency of rpm-pkg for openSUSE

* tag 'kbuild-fixes-v6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  fixdep: remove unneeded <stdarg.h> inclusion
  kbuild: sort single-targets alphabetically again
  kbuild: rpm-pkg: add libelf-devel as alternative for BuildRequires
  kbuild: Fix running modpost with musl libc
  kbuild: add a missing line for help message
  .gitignore: ignore *.rpm
  arch: fix broken BuildID for arm64 and riscv
  kconfig: Add static text for search information in help menu

Pull ata fix from Damien Le Moal:
 "A single fix to address an issue with wake from suspend with PCS
  adapters, from Adam"

* tag 'ata-6.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
  ata: ahci: Fix PCS quirk application for suspend

Pull ACPI fixes from Rafael Wysocki:
 "These are new ACPI IRQ override quirks, low-power S0 idle (S0ix)
  support adjustments and ACPI backlight handling fixes, mostly for
  platforms using AMD chips.

  Specifics:

   - Add ACPI IRQ override quirks for Asus ExpertBook B2502, Lenovo
     14ALC7, and XMG Core 15 (Hans de Goede, Adrian Freund, Erik
     Schumacher).

   - Adjust ACPI video detection fallback path to prevent
     non-operational ACPI backlight devices from being created on
     systems where the native driver does not detect a suitable panel
     (Mario Limonciello).

   - Fix Apple GMUX backlight detection (Hans de Goede).

   - Add a low-power S0 idle (S0ix) handling quirk for HP Elitebook 865
     and stop using AMD-specific low-power S0 idle code path for systems
     with Rembrandt chips and newer (Mario Limonciello)"

* tag 'acpi-6.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI: x86: s2idle: Stop using AMD specific codepath for Rembrandt+
  ACPI: x86: s2idle: Force AMD GUID/_REV 2 on HP Elitebook 865
  ACPI: video: Fix Apple GMUX backlight detection
  ACPI: resource: Add Asus ExpertBook B2502 to Asus quirks
  ACPI: resource: do IRQ override on Lenovo 14ALC7
  ACPI: resource: do IRQ override on XMG Core 15
  ACPI: video: Don't enable fallback path for creating ACPI backlight by default
  drm/amd/display: Report to ACPI video if no panels were found
  ACPI: video: Allow GPU drivers to report no panels

Pull sound fixes from Takashi Iwai:
 "Just a few small fixes:

   - A regression fix for HDMI audio on HD-audio AMD codecs

   - Fixes for LINE6 MIDI handling

   - HD-audio quirk for Dell laptops"

* tag 'sound-6.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda/hdmi: Static PCM mapping again with AMD HDMI codecs
  ALSA: hda/realtek: Apply dual codec fixup for Dell Latitude laptops
  ALSA: line6: fix stack overflow in line6_midi_transmit
  ALSA: line6: correct midi status byte when receiving data from podxt

Merge ACPI resource handling quirks and ACPI backlight handling fixes
for 6.2-rc2:

 - Add ACPI IRQ override quirks for Asus ExpertBook B2502, Lenovo
   14ALC7, and XMG Core 15 (Hans de Goede, Adrian Freund,  Erik
   Schumacher).

 - Adjust ACPI video detection fallback path to prevent non-operational
   ACPI backlight devices from being created on systems where the native
   driver does not detect a suitable panel (Mario Limonciello).

 - Fix Apple GMUX backlight detection (Hans de Goede).

* acpi-resource:
  ACPI: resource: Add Asus ExpertBook B2502 to Asus quirks
  ACPI: resource: do IRQ override on Lenovo 14ALC7
  ACPI: resource: do IRQ override on XMG Core 15

* acpi-video:
  ACPI: video: Fix Apple GMUX backlight detection
  ACPI: video: Don't enable fallback path for creating ACPI backlight by default
  drm/amd/display: Report to ACPI video if no panels were found
  ACPI: video: Allow GPU drivers to report no panels

Due to copy-paste fail, MIPI_BKLT_EN_1 would always use PPS index 1,
never 0. Fix the sloppiest commit in recent memory.

Fixes: 963bbdb3 ("drm/i915/dsi: add support for ICL+ native MIPI GPIO sequence")
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221220140105.313333-1-jani.nikula@intel.com
(cherry picked from commit a561933c)
Cc: stable@vger.kernel.org # 6.1
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

Starting from ICL, the default for MIPI GPIO sequences seems to be using
native GPIOs i.e. GPIOs available in the GPU. These native GPIOs reuse
many pins that quite frankly seem scary to poke based on the VBT
sequences. We pretty much have to trust that the board is configured
such that the relevant HPD, PP_CONTROL and GPIO bits aren't used for
anything else.

MIPI sequence v4 also adds a flag to fall back to non-native sequences.

v5:
- Wrap SHOTPLUG_CTL_DDI modification in spin_lock() in icp_irq_handler()
  too (Ville)
- References instead of Closes issue 6131 because this does not fix everything

v4:
- Wrap SHOTPLUG_CTL_DDI modification in spin_lock_irq() (Ville)

v3:
- Fix -Wbitwise-conditional-parentheses (kernel test robot <lkp@intel.com>)

v2:
- Fix HPD pin output set (impacts GPIOs 0 and 5)
- Fix GPIO data output direction set (impacts GPIOs 4 and 9)
- Reduce register accesses to single intel_de_rwm()

References: https://gitlab.freedesktop.org/drm/intel/-/issues/6131
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221219105955.4014451-1-jani.nikula@intel.com
(cherry picked from commit f087cfe6)
Cc: stable@vger.kernel.org # 6.1
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

This is unneeded since commit 69304379 ("fixdep: use fflush() and
ferror() to ensure successful write to files").
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>

This was previously alphabetically sorted. Sort it again.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>

Guoqing Jiang reports that openSUSE cannot compile the kernel rpm due
to "BuildRequires: elfutils-libelf-devel" added by commit 8818039f
("kbuild: add ability to make source rpm buildable using koji").
The relevant package name in openSUSE is libelf-devel.

Add it as an alternative package.

BTW, if it is impossible to solve the build requirement, the final
resort would be:

    $ make RPMOPTS=--nodeps rpm-pkg

This passes --nodeps to the rpmbuild command so it will not verify
build dependencies. This is useful to test rpm builds on non-rpm
system. On Debian/Ubuntu, for example, you can install rpmbuild by
'apt-get install rpm'.

NOTE1:
  Likewise, it is possible to bypass the build dependency check for
  debian package builds:

    $ make DPKG_FLAGS=-d deb-pkg

NOTE2:
  The 'or' operator is supported since RPM 4.13. So, old distros such
  as CentOS 7 will break. I suggest installing newer rpmbuild in such
  cases.

Link: https://lore.kernel.org/linux-kbuild/ee227d24-9c94-bfa3-166a-4ee6b5dfea09@linux.dev/T/#u
Fixes: 8818039f ("kbuild: add ability to make source rpm buildable using koji")
Reported-by: Guoqing Jiang <guoqing.jiang@linux.dev>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Guoqing Jiang <guoqing.jiang@linux.dev>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>

commit 3d57e1b7 ("kbuild: refactor the prerequisites of the modpost
rule") moved 'vmlinux.o' inside modpost-args, possibly before some of
the other options. However, getopt() in musl libc follows POSIX and
stops looking for options upon reaching the first non-option argument.
As a result, the '-T' option is misinterpreted as a positional argument,
and the build fails:

  make -f ./scripts/Makefile.modpost
     scripts/mod/modpost   -E   -o Module.symvers vmlinux.o -T modules.order
  -T: No such file or directory
  make[1]: *** [scripts/Makefile.modpost:137: Module.symvers] Error 1
  make: *** [Makefile:1960: modpost] Error 2

The fix is to move all options before 'vmlinux.o' in modpost-args.

Fixes: 3d57e1b7 ("kbuild: refactor the prerequisites of the modpost rule")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>

The help message line for building the source RPM package was missing.
Added it.
Signed-off-by: Jun ASAKA <JunASAKA@zzy040330.moe>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>