NFSv3 includes pre/post wcc attributes which allow the client to
determine if all changes to the file have been made by the client
itself, or if any might have been made by some other client.

If there are gaps in the pre/post ctime sequence it must be assumed that
some other client changed the file in that gap and the local cache must
be suspect.  The next time the file is opened the cache should be
invalidated.

Since Commit 1c341b77 ("NFS: Add deferred cache invalidation for
close-to-open consistency violations") in linux 5.3 the Linux client has
been triggering this invalidation.  The chunk in nfs_update_inode() in
particularly triggers.

Unfortunately Linux NFS assumes that all replies will be processed in
the order sent, and will arrive in the order processed.  This is not
true in general.  Consequently Linux NFS might ignore the wcc info in a
WRITE reply because the reply is in response to a WRITE that was sent
before some other request for which a reply has already been seen.  This
is detected by Linux using the gencount tests in nfs_inode_attr_cmp().

Also, when the gencount tests pass it is still possible that the request
were processed on the server in a different order, and a gap seen in
the ctime sequence might be filled in by a subsequent reply, so gaps
should not immediately trigger delayed invalidation.

The net result is that writing to a server and then reading the file
back can result in going to the server for the read rather than serving
it from cache - all because a couple of replies arrived out-of-order.
This is a performance regression over kernels before 5.3, though the
change in 5.3 is a correctness improvement.

This has been seen with Linux writing to a Netapp server which
occasionally re-orders requests.  In testing the majority of requests
were in-order, but a few (maybe 2 or three at a time) could be
re-ordered.

This patch addresses the problem by recording any gaps seen in the
pre/post ctime sequence and not triggering invalidation until either
there are too many gaps to fit in the table, or until there are no more
active writes and the remaining gaps cannot be resolved.

We allocate a table of 16 gaps on demand.  If the allocation fails we
revert to current behaviour which is of little cost as we are unlikely
to be able to cache the writes anyway.

In the table we store "start->end" pair when iversion is updated and
"end<-start" pairs pre/post pairs reported by the server.  Usually these
exactly cancel out and so nothing is stored.  When there are
out-of-order replies we do store gaps and these will eventually be
cancelled against later replies when this client is the only writer.

If the final write is out-of-order there may be one gap remaining when
the file is closed.  This will be noticed and if there is precisely on
gap and if the iversion can be advanced to match it, then we do so.

This patch makes no attempt to handle directories correctly.  The same
problem potentially exists in the out-of-order replies to create/unlink
requests can cause future lookup requires to be sent to the server
unnecessarily.  A similar scheme using the same primitives could be used
to notice and handle out-of-order replies.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>

The NFS specific trace points are no longer needed as tracing is well
covered by netfs and fscache.
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Tested-by: Daire Byrne <daire@dneg.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>

The old NFSIOS_FSCACHE counters are no longer accurate or useful with
the conversion to the new netfs API.  The new API does not have a page
based interface, and so the counters in nfs_stat_fscachecounters are
no longer obtainable.  The new netfs the API has extensive statistics
inside /proc/fs/fscache/stats so we no longer need NFS specific fscache
stats.

Note this also removes the 'fsc:' line from /proc/self/mountstats so
it will be a user-visible change.
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Tested-by: Daire Byrne <daire@dneg.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>

Convert the NFS buffered read code paths to corresponding netfs APIs,
but only when fscache is configured and enabled.

The netfs API defines struct netfs_request_ops which must be filled
in by the network filesystem.  For NFS, we only need to define 5 of
the functions, the main one being the issue_read() function.
The issue_read() function is called by the netfs layer when a read
cannot be fulfilled locally, and must be sent to the server (either
the cache is not active, or it is active but the data is not available).
Once the read from the server is complete, netfs requires a call to
netfs_subreq_terminated() which conveys either how many bytes were read
successfully, or an error.  Note that issue_read() is called with a
structure, netfs_io_subrequest, which defines the IO requested, and
contains a start and a length (both in bytes), and assumes the underlying
netfs will return a either an error on the whole region, or the number
of bytes successfully read.

The NFS IO path is page based and the main APIs are the pgio APIs defined
in pagelist.c.  For the pgio APIs, there is no way for the caller to
know how many RPCs will be sent and how the pages will be broken up
into underlying RPCs, each of which will have their own completion and
return code.  In contrast, netfs is subrequest based, a single
subrequest may contain multiple pages, and a single subrequest is
initiated with issue_read() and terminated with netfs_subreq_terminated().
Thus, to utilze the netfs APIs, NFS needs some way to accommodate
the netfs API requirement on the single response to the whole
subrequest, while also minimizing disruptive changes to the NFS
pgio layer.

The approach taken with this patch is to allocate a small structure
for each nfs_netfs_issue_read() call, store the final error and number
of bytes successfully transferred in the structure, and update these values
as each RPC completes.  The refcount on the structure is used as a marker
for the last RPC completion, is incremented in nfs_netfs_read_initiate(),
and decremented inside nfs_netfs_read_completion(), when a nfs_pgio_header
contains a valid pointer to the data.  On the final put (which signals
the final outstanding RPC is complete) in nfs_netfs_read_completion(),
call netfs_subreq_terminated() with either the final error value (if
one or more READs complete with an error) or the number of bytes
successfully transferred (if all RPCs complete successfully).  Note
that when all RPCs complete successfully, the number of bytes transferred
is capped to the length of the subrequest.  Capping the transferred length
to the subrequest length prevents "Subreq overread" warnings from netfs.
This is due to the "aligned_len" in nfs_pageio_add_page(), and the
corner case where NFS requests a full page at the end of the file,
even when i_size reflects only a partial page (NFS overread).
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com>
Tested-by: Daire Byrne <daire@dneg.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>

As first steps for support of the netfs library when NFS_FSCACHE is
configured, add NETFS_SUPPORT to Kconfig and add the required netfs_inode
into struct nfs_inode.

Using netfs requires we move the VFS inode structure to be stored
inside struct netfs_inode, along with the fscache_cookie.
Thus, if NFS_FSCACHE is configured, place netfs_inode inside an
anonymous union so the vfs_inode memory is the same and we do
not need to modify other non-fscache areas of NFS.
In addition, inside the NFS fscache code, use the new helpers,
netfs_inode() and netfs_i_cookie() helpers, and remove our own
helper, nfs_i_fscache().

Later patches will convert NFS fscache to fully use netfs.
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com>
Tested-by: Daire Byrne <daire@dneg.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>

Rename readpage_async_filler to nfs_read_add_folio to
better reflect what this function does (add a folio to
the nfs_pageio_descriptor), and simplify arguments to
this function by removing struct nfs_readdesc.
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com>
Tested-by: Daire Byrne <daire@dneg.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>

There is no need to declare an extra tables to just create directory,
this can be easily be done with a prefix path with register_sysctl().

Simplify this registration.
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>

No need to do a forward declaration for sunrpc_table, just move
the sysctls up as everyone else does it. This will make the next
change easier to read. This change produces no functional changes.
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>

There is no need to declare an extra tables to just create directory,
this can be easily be done with a prefix path with register_sysctl().

Simplify this registration.
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>

There is no need to declare an extra tables to just create directory,
this can be easily be done with a prefix path with register_sysctl().

Simplify this registration.
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>

There is no need to declare two tables to just create directories,
this can be easily be done with a prefix path with register_sysctl().

Simplify this registration.
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>

There is no need to declare two tables to just create directories,
this can be easily be done with a prefix path with register_sysctl().

Simplify this registration.
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>

There is no need to declare two tables to just create directories,
this can be easily be done with a prefix path with register_sysctl().

Simplify this registration.
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>

The spec requires that we always at least send a RECLAIM_COMPLETE when
we're done establishing the lease and recovering any state.

Fixes: fce5c838 ("nfs41: RECLAIM_COMPLETE functionality")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>

Pull perf fixes from Borislav Petkov:

 - Fix "same task" check when redirecting event output

 - Do not wait unconditionally for RCU on the event migration path if
   there are no events to migrate

* tag 'perf_urgent_for_v6.3_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/core: Fix the same task check in perf_event_set_output
  perf: Optimize perf_pmu_migrate_context()

Pull x86 fixes from Borislav Petkov:

 - Add a new Intel Arrow Lake CPU model number

 - Fix a confusion about how to check the version of the ACPI spec which
   supports a "online capable" bit in the MADT table which lead to a
   bunch of boot breakages with Zen1 systems and VMs

* tag 'x86_urgent_for_v6.3_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/cpu: Add model number for Intel Arrow Lake processor
  x86/acpi/boot: Correct acpi_is_processor_usable() check
  x86/ACPI/boot: Use FADT version to check support for online capable

Pull compute express link (cxl) fixes from Dan Williams:
 "Several fixes for driver startup regressions that landed during the
  merge window as well as some older bugs.

  The regressions were due to a lack of testing with what the CXL
  specification calls Restricted CXL Host (RCH) topologies compared to
  the testing with Virtual Host (VH) CXL topologies. A VH topology is
  typical PCIe while RCH topologies map CXL endpoints as Root Complex
  Integrated endpoints. The impact is some driver crashes on startup.

  This merge window also added compatibility for range registers (the
  mechanism that CXL 1.1 defined for mapping memory) to treat them like
  HDM decoders (the mechanism that CXL 2.0 defined for mapping
  Host-managed Device Memory). That work collided with the new region
  enumeration code that was tested with CXL 2.0 setups, and fails with
  crashes at startup.

  Lastly, the DOE (Data Object Exchange) implementation for retrieving
  an ACPI-like data table from CXL devices is being reworked for v6.4.
  Several fixes fell out of that work that are suitable for v6.3.

  All of this has been in linux-next for a while, and all reported
  issues [1] have been addressed.

  Summary:

   - Fix several issues with region enumeration in RCH topologies that
     can trigger crashes on driver startup or shutdown.

   - Fix CXL DVSEC range register compatibility versus region
     enumeration that leads to startup crashes

   - Fix CDAT endiannes handling

   - Fix multiple buffer handling boundary conditions

   - Fix Data Object Exchange (DOE) workqueue usage vs
     CONFIG_DEBUG_OBJECTS warn splats"

Link: http://lore.kernel.org/r/20230405075704.33de8121@canb.auug.org.au [1]

* tag 'cxl-fixes-6.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
  cxl/hdm: Extend DVSEC range register emulation for region enumeration
  cxl/hdm: Limit emulation to the number of range registers
  cxl/region: Move coherence tracking into cxl_region_attach()
  cxl/region: Fix region setup/teardown for RCDs
  cxl/port: Fix find_cxl_root() for RCDs and simplify it
  cxl/hdm: Skip emulation when driver manages mem_enable
  cxl/hdm: Fix double allocation of @cxlhdm
  PCI/DOE: Fix memory leak with CONFIG_DEBUG_OBJECTS=y
  PCI/DOE: Silence WARN splat with CONFIG_DEBUG_OBJECTS=y
  cxl/pci: Handle excessive CDAT length
  cxl/pci: Handle truncated CDAT entries
  cxl/pci: Handle truncated CDAT header
  cxl/pci: Fix CDAT retrieval on big endian

Pull cifs client fixes from Steve French:
 "Two cifs/smb3 client fixes, one for stable:

   - double lock fix for a cifs/smb1 reconnect path

   - DFS prefixpath fix for reconnect when server moved"

* tag '6.3-rc5-smb3-cifs-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: double lock in cifs_reconnect_tcon()
  cifs: sanitize paths in cifs_update_super_prepath.

Pull char/misc driver fixes from Greg KH:
 "Here are a small set of various small driver changes for 6.3-rc6.
  Included in here are:

   - iio driver fixes for reported problems

   - coresight hwtracing bugfix for reported problem

   - small counter driver bugfixes

  All have been in linux-next for a while with no reported problems"

* tag 'char-misc-6.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  coresight: etm4x: Do not access TRCIDR1 for identification
  coresight-etm4: Fix for() loop drvdata->nr_addr_cmp range bug
  iio: adc: ti-ads7950: Set `can_sleep` flag for GPIO chip
  iio: adc: palmas_gpadc: fix NULL dereference on rmmod
  counter: 104-quad-8: Fix Synapse action reported for Index signals
  counter: 104-quad-8: Fix race condition between FLAG and CNTR reads
  iio: adc: max11410: fix read_poll_timeout() usage
  iio: dac: cio-dac: Fix max DAC write value check for 12-bit
  iio: light: cm32181: Unregister second I2C client if present
  iio: accel: kionix-kx022a: Get the timestamp from the driver's private data in the trigger_handler
  iio: adc: ad7791: fix IRQ flags
  iio: buffer: make sure O_NONBLOCK is respected
  iio: buffer: correctly return bytes written in output buffers
  iio: light: vcnl4000: Fix WARN_ON on uninitialized lock
  iio: adis16480: select CONFIG_CRC32
  drivers: iio: adc: ltc2497: fix LSB shift
  iio: adc: qcom-spmi-adc5: Fix the channel name

Pull tty/serial driver fixes from Greg KH:
 "Here are some small tty and serial driver fixes for some reported
  problems:

   - fsl_uart driver bugfixes

   - sh-sci serial driver bugfixes

   - renesas serial driver DT binding bugfixes

   - 8250 DMA bugfix

  All of these have been in linux-next for a while with no reported
  problems"

* tag 'tty-6.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: serial: sh-sci: Fix Rx on RZ/G2L SCI
  tty: serial: fsl_lpuart: fix crash in lpuart_uport_is_active
  tty: serial: fsl_lpuart: avoid checking for transfer complete when UARTCTRL_SBK is asserted in lpuart32_tx_empty
  serial: 8250: Prevent starting up DMA Rx on THRI interrupt
  dt-bindings: serial: renesas,scif: Fix 4th IRQ for 4-IRQ SCIFs
  tty: serial: sh-sci: Fix transmit end interrupt handler

Pull USB bugfixes from Greg KH:
 "Here are some small USB bugfixes for 6.3-rc6 that have been in my
  tree, and in linux-next, for a while. Included in here are:

   - new usb-serial driver device ids

   - xhci bugfixes for reported problems

   - gadget driver bugfixes for reported problems

   - dwc3 new device id

  All have been in linux-next with no reported problems"

* tag 'usb-6.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: cdnsp: Fixes error: uninitialized symbol 'len'
  usb: gadgetfs: Fix ep_read_iter to handle ITER_UBUF
  usb: gadget: f_fs: Fix ffs_epfile_read_iter to handle ITER_UBUF
  usb: typec: altmodes/displayport: Fix configure initial pin assignment
  usb: dwc3: pci: add support for the Intel Meteor Lake-S
  xhci: Free the command allocated for setting LPM if we return early
  Revert "usb: xhci-pci: Set PROBE_PREFER_ASYNCHRONOUS"
  xhci: also avoid the XHCI_ZERO_64B_REGS quirk with a passthrough iommu
  USB: serial: option: add Quectel RM500U-CN modem
  usb: xhci: tegra: fix sleep in atomic call
  USB: serial: option: add Telit FE990 compositions
  USB: serial: cp210x: add Silicon Labs IFS-USB-DATACABLE IDs

Pull SCSI fixes from James Bottomley:
 "Four small fixes, all in drivers. They're all one or two lines except
  for the ufs one, but that's a simple revert of a previous feature"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: iscsi_tcp: Check that sock is valid before iscsi_set_param()
  scsi: qla2xxx: Fix memory leak in qla2x00_probe_one()
  scsi: mpi3mr: Handle soft reset in progress fault code (0xF002)
  scsi: Revert "scsi: ufs: core: Initialize devfreq synchronously"

Pull block fixes from Jens Axboe:

 - Ensure that ublk always reads the whole sqe upfront (me)

 - Fix for a block size probing issue with ublk (Ming)

 - Fix for the bio based polling (Keith)

 - NVMe pull request via Christoph:
      - fix discard support without oncs (Keith Busch)

 - Partition scan error handling regression fix (Yu)

* tag 'block-6.3-2023-04-06' of git://git.kernel.dk/linux:
  block: don't set GD_NEED_PART_SCAN if scan partition failed
  block: ublk: make sure that block size is set correctly
  ublk: read any SQE values upfront
  nvme: fix discard support without oncs
  blk-mq: directly poll requests

Pull io_uring fixes from Jens Axboe:
 "Just two minor fixes for provided buffers - one where we could
  potentially leak a buffer, and one where the returned values was
  off-by-one in some cases"

* tag 'io_uring-6.3-2023-04-06' of git://git.kernel.dk/linux:
  io_uring: fix memory leak when removing provided buffers
  io_uring: fix return value when removing provided buffers

Pull dma-mapping fix from Christoph Hellwig:

 - fix a braino in the swiotlb alignment check fix (Petr Tesarik)

* tag 'dma-mapping-6.3-2023-04-08' of git://git.infradead.org/users/hch/dma-mapping:
  swiotlb: fix a braino in the alignment check fix

Pull tracing fixes from Steven Rostedt:
 "A couple more minor fixes:

   - Reset direct->addr back to its original value on error in updating
     the direct trampoline code

   - Make lastcmd_mutex static"

* tag 'trace-v6.3-rc5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
  tracing/synthetic: Make lastcmd_mutex static
  ftrace: Fix issue that 'direct->addr' not restored in modify_ftrace_direct()

Merge tag 'mm-hotfixes-stable-2023-04-07-16-23' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm

Pull MM fixes from Andrew Morton:
 "28 hotfixes.

  23 are cc:stable and the other five address issues which were
  introduced during this merge cycle.

  20 are for MM and the remainder are for other subsystems"

* tag 'mm-hotfixes-stable-2023-04-07-16-23' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (28 commits)
  maple_tree: fix a potential concurrency bug in RCU mode
  maple_tree: fix get wrong data_end in mtree_lookup_walk()
  mm/swap: fix swap_info_struct race between swapoff and get_swap_pages()
  nilfs2: fix sysfs interface lifetime
  mm: take a page reference when removing device exclusive entries
  mm: vmalloc: avoid warn_alloc noise caused by fatal signal
  nilfs2: initialize "struct nilfs_binfo_dat"->bi_pad field
  nilfs2: fix potential UAF of struct nilfs_sc_info in nilfs_segctor_thread()
  zsmalloc: document freeable stats
  zsmalloc: document new fullness grouping
  fsdax: force clear dirty mark if CoW
  mm/hugetlb: fix uffd wr-protection for CoW optimization path
  mm: enable maple tree RCU mode by default
  maple_tree: add RCU lock checking to rcu callback functions
  maple_tree: add smp_rmb() to dead node detection
  maple_tree: fix write memory barrier of nodes once dead for RCU mode
  maple_tree: remove extra smp_wmb() from mas_dead_leaves()
  maple_tree: fix freeing of nodes in rcu mode
  maple_tree: detect dead nodes in mas_start()
  maple_tree: be more cautious about dead nodes
  ...

Pull gpio fixes from Bartosz Golaszewski:

 - fix irq handling in gpio-davinci

 - fix Kconfig dependencies for gpio-regmap

* tag 'gpio-fixes-for-v6.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
  gpio: davinci: Add irq chip flag to skip set wake
  gpio: davinci: Do not clear the bank intr enable bit in save_context
  gpio: GPIO_REGMAP: select REGMAP instead of depending on it

Pull ACPI fixes from Rafael Wysocki:
 "Fix the ACPI backlight override mechanism for the cases when
  acpi_backlight=video is set through the kernel command line or a DMI
  quirk and add backlight quirks for Apple iMac14,1 and iMac14,2 and
  Lenovo ThinkPad W530 (Hans de Goede)"

* tag 'acpi-6.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI: video: Add acpi_backlight=video quirk for Lenovo ThinkPad W530
  ACPI: video: Add acpi_backlight=video quirk for Apple iMac14,1 and iMac14,2
  ACPI: video: Make acpi_backlight=video work independent from GPU driver
  ACPI: video: Add auto_detect arg to __acpi_video_get_backlight_type()

Pull arm64 fix from Catalin Marinas:
 "Fix uninitialised variable warning (from smatch) in the arm64 compat
  alignment fixup code"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: compat: Work around uninitialized variable warning

Pull ksmbd server fixes from Steve French:
 "Four fixes, three for stable:

   - slab out of bounds fix

   - lock cancellation fix

   - minor cleanup to address clang warning

   - fix for xfstest 551 (wrong parms passed to kvmalloc)"

* tag '6.3-rc5-ksmbd-server-fixes' of git://git.samba.org/ksmbd:
  ksmbd: fix slab-out-of-bounds in init_smb2_rsp_hdr
  ksmbd: delete asynchronous work from list
  ksmbd: remove unused is_char_allowed function
  ksmbd: do not call kvmalloc() with __GFP_NORETRY | __GFP_NO_WARN

This lock was supposed to be an unlock.

Fixes: 6cc041e9 ("cifs: avoid races in parallel reconnects in smb1")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>

Currently if disk_scan_partitions() failed, GD_NEED_PART_SCAN will still
set, and partition scan will be proceed again when blkdev_get_by_dev()
is called. However, this will cause a problem that re-assemble partitioned
raid device will creat partition for underlying disk.

Test procedure:

mdadm -CR /dev/md0 -l 1 -n 2 /dev/sda /dev/sdb -e 1.0
sgdisk -n 0:0:+100MiB /dev/md0
blockdev --rereadpt /dev/sda
blockdev --rereadpt /dev/sdb
mdadm -S /dev/md0
mdadm -A /dev/md0 /dev/sda /dev/sdb

Test result: underlying disk partition and raid partition can be
observed at the same time

Note that this can still happen in come corner cases that
GD_NEED_PART_SCAN can be set for underlying disk while re-assemble raid
device.

Fixes: e5cfefa9 ("block: fix scan partition for exclusively open device again")
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

The lastcmd_mutex is only used in trace_events_synth.c and should be
static.

Link: https://lore.kernel.org/linux-trace-kernel/202304062033.cRStgOuP-lkp@intel.com/
Link: https://lore.kernel.org/linux-trace-kernel/20230406111033.6e26de93@gandalf.local.home

Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Tze-nan Wu <Tze-nan.Wu@mediatek.com>
Fixes: 4ccf11c4 ("tracing/synthetic: Fix races on freeing last_cmd")
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>

Pull networking fixes from Jakub Kicinski:
 "Including fixes from wireless and can.

  Current release - regressions:

   - wifi: mac80211:
      - fix potential null pointer dereference
      - fix receiving mesh packets in forwarding=0 networks
      - fix mesh forwarding

  Current release - new code bugs:

   - virtio/vsock: fix leaks due to missing skb owner

  Previous releases - regressions:

   - raw: fix NULL deref in raw_get_next().

   - sctp: check send stream number after wait_for_sndbuf

   - qrtr:
      - fix a refcount bug in qrtr_recvmsg()
      - do not do DEL_SERVER broadcast after DEL_CLIENT

   - wifi: brcmfmac: fix SDIO suspend/resume regression

   - wifi: mt76: fix use-after-free in fw features query.

   - can: fix race between isotp_sendsmg() and isotp_release()

   - eth: mtk_eth_soc: fix remaining throughput regression

   - eth: ice: reset FDIR counter in FDIR init stage

  Previous releases - always broken:

   - core: don't let netpoll invoke NAPI if in xmit context

   - icmp: guard against too small mtu

   - ipv6: fix an uninit variable access bug in __ip6_make_skb()

   - wifi: mac80211: fix the size calculation of
     ieee80211_ie_len_eht_cap()

   - can: fix poll() to not report false EPOLLOUT events

   - eth: gve: secure enough bytes in the first TX desc for all TCP
     pkts"

* tag 'net-6.3-rc6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (47 commits)
  net: stmmac: check fwnode for phy device before scanning for phy
  net: stmmac: Add queue reset into stmmac_xdp_open() function
  selftests: net: rps_default_mask.sh: delete veth link specifically
  net: fec: make use of MDIO C45 quirk
  can: isotp: fix race between isotp_sendsmg() and isotp_release()
  can: isotp: isotp_ops: fix poll() to not report false EPOLLOUT events
  can: isotp: isotp_recvmsg(): use sock_recv_cmsgs() to get SOCK_RXQ_OVFL infos
  can: j1939: j1939_tp_tx_dat_new(): fix out-of-bounds memory access
  gve: Secure enough bytes in the first TX desc for all TCP pkts
  netlink: annotate lockless accesses to nlk->max_recvmsg_len
  ethtool: reset #lanes when lanes is omitted
  ping: Fix potentail NULL deref for /proc/net/icmp.
  raw: Fix NULL deref in raw_get_next().
  ice: Reset FDIR counter in FDIR init stage
  ice: fix wrong fallback logic for FDIR
  net: stmmac: fix up RX flow hash indirection table when setting channels
  net: ethernet: ti: am65-cpsw: Fix mdio cleanup in probe
  wifi: mt76: ignore key disable commands
  wifi: ath11k: reduce the MHI timeout to 20s
  ipv6: Fix an uninit variable access bug in __ip6_make_skb()
  ...

Merge tag 'linux-kselftest-fixes-6.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull Kselftest fixes from Shuah Khan:
 "One single fix to mount_setattr_test build failure"

* tag 'linux-kselftest-fixes-6.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  selftests mount: Fix mount_setattr_test builds failed

Pull iommufd fixes from Jason Gunthorpe:

 - An invalid VA range can be be put in a pages and eventually trigger
   WARN_ON, reject it early

 - Use of the wrong start index value when doing the complex batch carry
   scheme

 - Wrong store ordering resulting in corrupting data used in a later
   calculation that corrupted the batch structure during carry

* tag 'for-linus-iommufd' of git://git.kernel.org/pub/scm/linux/kernel/git/jgg/iommufd:
  iommufd: Do not corrupt the pfn list when doing batch carry
  iommufd: Fix unpinning of pages when an access is present
  iommufd: Check for uptr overflow

Merge tag 'pwm/for-6.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm

Pull pwm fixes from Thierry Reding:
 "These are some fixes to make sure the PWM state structure is always
  initialized to a known state.

  Prior to this it could happen in some situations that random data from
  the stack would leak into the data structure and cause subtle bugs"

* tag 'pwm/for-6.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
  pwm: Zero-initialize the pwm_state passed to driver's .get_state()
  pwm: meson: Explicitly set .polarity in .get_state()
  pwm: sprd: Explicitly set .polarity in .get_state()
  pwm: iqs620a: Explicitly set .polarity in .get_state()
  pwm: cros-ec: Explicitly set .polarity in .get_state()
  pwm: hibvt: Explicitly set .polarity in .get_state()

Pull drm fixes from Daniel Vetter:
 "Mostly i915 fixes: dp mst for compression/dsc, perf ioctl uaf, ctx rpm
  accounting, gt reset vs huc loading.

  And a few individual driver fixes: ivpu dma fence&suspend, panfrost
  mmap, nouveau color depth"

* tag 'drm-fixes-2023-04-06' of git://anongit.freedesktop.org/drm/drm:
  accel/ivpu: Fix S3 system suspend when not idle
  accel/ivpu: Add dma fence to command buffers only
  drm/i915: Fix context runtime accounting
  drm/i915: fix race condition UAF in i915_perf_add_config_ioctl
  drm/i915: Use compressed bpp when calculating m/n value for DP MST DSC
  drm/i915/huc: Cancel HuC delayed load timer on reset.
  drm/i915/ttm: fix sparse warning
  drm/panfrost: Fix the panfrost_mmu_map_fault_addr() error path
  drm/nouveau/disp: Support more modes by checking with lower bpc