Looks like we've had the sgx sysconfig register and revision register
always wrong for omap4, including the old platform data. Let's fix the
offsets to what the TRM says. Otherwise the sgx module may never idle
depending on the state of the real sysconfig register.

Fixes: d23a163e ("ARM: dts: Add nodes for missing omap4 interconnect target modules")
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

In addition to using vcsi regulator for the display, looks like droid4 is
using vcsi regulator to trigger off mode internally with the PMIC firmware
when the SoC enters deeper idle states. This is configured in the Motorola
Mapphone Linux kernel sources as "zerov_regulator".

As we currently don't support off mode during idle for omap4, we must
prevent vcsi from being disabled when the display is blanked to prevent
the PMIC change to off mode. Otherwise the device will hang on entering
idle when the display is blanked.

Before commit 089b3f61 ("regulator: core: Let boot-on regulators be
powered off"), the boot-on regulators never got disabled like they should
and vcsi did not get turned off on idle.

Let's fix the issue by setting vcsi to always-on for now. Later on we may
want to claim the vcsi regulator also in the PM code if needed.

Fixes: 089b3f61 ("regulator: core: Let boot-on regulators be powered off")
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The DRA7 CPSW MDIO functional clock (gmac_clkctrl DRA7_GMAC_GMAC_CLKCTRL 0)
is specified incorrectly, which is caused incorrect MDIO bus clock
configuration MDCLK. The correct CPSW MDIO functional clock is
gmac_main_clk (125MHz), which is the same as CPSW fck. Hence fix it.

Fixes: 1faa415c ("ARM: dts: Add fck for cpsw mdio for omap variants")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

am57xx-beagle-x15 revb1 and revc have 3.3V connected to the eMMC I/O
lines. Update the pinmux name to reflect this.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The MMC card detection GPIO polarity is active low on TAO3530, like in many
other similar boards. Now the card is not detected and it is unable to
mount rootfs from an SD card.

Fix this by using the correct polarity.

This incorrect polarity was defined already in the commit 30d95c6d
("ARM: dts: omap3: Add Technexion TAO3530 SOM omap3-tao3530.dtsi") in v3.18
kernel and later changed to use defined GPIO constants in v4.4 kernel by
the commit 3a637e00 ("ARM: dts: Use defined GPIO constants in flags
cell for OMAP2+ boards").

While the latter commit did not introduce the issue I'm marking it with
Fixes tag due the v4.4 kernels still being maintained.

Fixes: 3a637e00 ("ARM: dts: Use defined GPIO constants in flags cell for OMAP2+ boards")
Cc: linux-stable <stable@vger.kernel.org> # 4.4+
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

There used to be a bug in the video driver that caused the timings
for the LCD to calculate in a way on the DM3730 which made it hang.

The work around for this bug was to set
CONFIG_OMAP2_DSS_MIN_FCK_PER_PCK=4 in the kernel.  This work around
is no longer needed as the video drivers have been corrected.

This patch removes the legacy note.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The baseboard of the Logic PD Torpedo development kit has a socket
for a rechargable battery.  The battery is monitored by a charger
which can communicate of the the 1-wire HDQ pin.

This patch enables the pinmux for the HDQ pin.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

While the OMAP3 family has a USB Host controller, the Torpedo
does not route the host pins off the board rendering it useless.

This patch removes the host references.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Looks like omap3 RNG is similar to the omap2 rng, let's get it working
by configring the dts node for it.

We must also add rng_ick to core_l4_clkdm as noted by Adam Ford.

And please note that the RNG is likely disabled on HS devices. At least
n900 does not have it accessible, and instead omap3-rom-rng driver must
be used. So let's tag RNG as disabled on n900 as noted by Pali Rohár
<pali.rohar@gmail.com>.

On am3517 at least the clocks need to be configured to get it working
as noted by Adam Ford, so let's tag it disabled for now.

Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Adam Ford <aford173@gmail.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd-torpedo-37xx-devkit
Signed-off-by: Tony Lindgren <tony@atomide.com>

This DTS file covers all four and eight port NetCom Plus devices.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This DTS file covers all one and two port NetCom Plus devices.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This DTS file covers both NetCAN Plus 110 and 120 WLAN models.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The device node name should reflect generic class of a device so rename
the "ocmcram" node to "sram".  This will be also in sync with upcoming DT
schema.  No functional change.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The default settings used on the baseboard are good for the
OMAP3530 and are compatible with the DM3730.  However, the
DM3730 has a faster L3 clock which means the camera pixel clock
can also be pushed faster as well.

This patch increase the Pixel clock to 90MHz which is the
maximum the current ISP driver permits for an L3 clock
of 200MHz.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The device node name should reflect generic class of a device so rename
the "ocmcram" node and its children to "sram".  This will be also in
sync with upcoming DT schema.  No functional change.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The default serial driver for omap2plus is the 8250_omap driver.
Unfortunately, this driver does not yet appear to have fully
functional DMA on OMAP3630/DM3730 which causes some timeouts and
frame errors.

This patch removes the DMA entry from the device tree which allow
the UART to operate without Bluetooth frame errors. If/when DMA
is working on OMAP3630, this should be reverted.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add a node for the UART part of WiLink chip.
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add a node for the UART part of WiLink chip.

This is compile tested only!

Cc: Adam Ford <aford173@gmail.com>
Acked-by: Adam Ford <aford173@gmail.com>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

With the removal of the panel-dpi from the omap drivers, the
LCD no longer works.  This patch points the device tree to
a newly created panel named "logicpd,type28"

Fixes: 8bf4b162 ("drm/omap: Remove panel-dpi driver")
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The dss driver wants two regulators or it dump some splat while
initializing.  This patch adds a reference to the second regulator
which to avoid the warnings that the regulator is missing.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We already have folks booting Droid Bionic with Droid 4 dts, but it is
a different hardware with no keyboard.

Let's start adding device specific support for Droid bionic by making
current omap4-droid4-xt894 a common file and including it.

Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Looks like we can use some USB Ethernet dongles for example if we increase
the allowed power limit.

A similar PMIC MC13783 documents maximum current limit as 300 mA in in
"Table 10-4. VBUS Regulator Main Characteristics". Since we have no
other documentation, let's use that value as the limit.

Cc: Jacopo Mondi <jacopo@jmondi.org>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Commit 572cf7d7 ("ARM: dts: Improve omap l4per idling with wlcore edge
sensitive interrupt") changed wlcore interrupts to use edge interrupt based
on what's specified in the wl1835mod.pdf data sheet.

However, there are still cases where we can have lost interrupts as
described in omap_gpio_unidle(). And using a level interrupt instead of edge
interrupt helps as we avoid the check for untriggered GPIO interrupts in
omap_gpio_unidle().

And with commit e6818d29 ("gpio: gpio-omap: configure edge detection
for level IRQs for idle wakeup") GPIOs idle just fine with level interrupts.

Let's change omap4 and 5 wlcore users back to using level interrupt
instead of edge interrupt. Let's not change the others as I've only seen
this on omap4 and 5, probably because the other SoCs don't have l4per idle
independent of the CPUs.

Fixes: 572cf7d7 ("ARM: dts: Improve omap l4per idling with wlcore edge sensitive interrupt")
Depends-on: e6818d29 ("gpio: gpio-omap: configure edge detection for level IRQs for idle wakeup")
Cc: Anders Roxell <anders.roxell@linaro.org>
Cc: Eyal Reizer <eyalr@ti.com>
Cc: Guy Mishol <guym@ti.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Pull btrfs fixes from David Sterba:
 "A bunch of fixes that accumulated in recent weeks, mostly material for
  stable.

  Summary:

   - fix for regression from 5.3 that prevents to use balance convert
     with single profile

   - qgroup fixes: rescan race, accounting leak with multiple writers,
     potential leak after io failure recovery

   - fix for use after free in relocation (reported by KASAN)

   - other error handling fixups"

* tag 'for-5.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: qgroup: Fix reserved data space leak if we have multiple reserve calls
  btrfs: qgroup: Fix the wrong target io_tree when freeing reserved data space
  btrfs: Fix a regression which we can't convert to SINGLE profile
  btrfs: relocation: fix use-after-free on dead relocation roots
  Btrfs: fix race setting up and completing qgroup rescan workers
  Btrfs: fix missing error return if writeback for extent buffer never started
  btrfs: adjust dirty_metadata_bytes after writeback failure of extent buffer
  Btrfs: fix selftests failure due to uninitialized i_mode in test inodes

Pull csky updates from Guo Ren:
 "This round of csky subsystem just some fixups:

   - Fix mb() synchronization problem

   - Fix dma_alloc_coherent with PAGE_SO attribute

   - Fix cache_op failed when cross memory ZONEs

   - Optimize arch_sync_dma_for_cpu/device with dma_inv_range

   - Fix ioremap function losing

   - Fix arch_get_unmapped_area() implementation

   - Fix defer cache flush for 610

   - Support kernel non-aligned access

   - Fix 610 vipt cache flush mechanism

   - Fix add zero_fp fixup perf backtrace panic

   - Move static keyword to the front of declaration

   - Fix csky_pmu.max_period assignment

   - Use generic free_initrd_mem()

   - entry: Remove unneeded need_resched() loop"

* tag 'csky-for-linus-5.4-rc1' of git://github.com/c-sky/csky-linux:
  csky: Move static keyword to the front of declaration
  csky: entry: Remove unneeded need_resched() loop
  csky: Fixup csky_pmu.max_period assignment
  csky: Fixup add zero_fp fixup perf backtrace panic
  csky: Use generic free_initrd_mem()
  csky: Fixup 610 vipt cache flush mechanism
  csky: Support kernel non-aligned access
  csky: Fixup defer cache flush for 610
  csky: Fixup arch_get_unmapped_area() implementation
  csky: Fixup ioremap function losing
  csky: Optimize arch_sync_dma_for_cpu/device with dma_inv_range
  csky/dma: Fixup cache_op failed when cross memory ZONEs
  csky: Fixup dma_alloc_coherent with PAGE_SO attribute
  csky: Fixup mb() synchronization problem

Pull ARM SoC fixes from Olof Johansson:
 "A few fixes that have trickled in through the merge window:

   - Video fixes for OMAP due to panel-dpi driver removal

   - Clock fixes for OMAP that broke no-idle quirks + nfsroot on DRA7

   - Fixing arch version on ASpeed ast2500

   - Two fixes for reset handling on ARM SCMI"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
  ARM: aspeed: ast2500 is ARMv6K
  reset: reset-scmi: add missing handle initialisation
  firmware: arm_scmi: reset: fix reset_state assignment in scmi_domain_reset
  bus: ti-sysc: Remove unpaired sysc_clkdm_deny_idle()
  ARM: dts: logicpd-som-lv: Fix i2c2 and i2c3 Pin mux
  ARM: dts: am3517-evm: Fix missing video
  ARM: dts: logicpd-torpedo-baseboard: Fix missing video
  ARM: omap2plus_defconfig: Fix missing video
  bus: ti-sysc: Fix handling of invalid clocks
  bus: ti-sysc: Fix clock handling for no-idle quirks

Pull tracing fixes from Steven Rostedt:
 "A few more tracing fixes:

   - Fix a buffer overflow by checking nr_args correctly in probes

   - Fix a warning that is reported by clang

   - Fix a possible memory leak in error path of filter processing

   - Fix the selftest that checks for failures, but wasn't failing

   - Minor clean up on call site output of a memory trace event"

* tag 'trace-v5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  selftests/ftrace: Fix same probe error test
  mm, tracing: Print symbol name for call_site in trace events
  tracing: Have error path in predicate_parse() free its allocated memory
  tracing: Fix clang -Wint-in-bool-context warnings in IF_ASSIGN macro
  tracing/probe: Fix to check the difference of nr_args before adding probe

Pull more MMC updates from Ulf Hansson:
 "A couple more updates/fixes for MMC:

   - sdhci-pci: Add Genesys Logic GL975x support

   - sdhci-tegra: Recover loss in throughput for DMA

   - sdhci-of-esdhc: Fix DMA bug"

* tag 'mmc-v5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: host: sdhci-pci: Add Genesys Logic GL975x support
  mmc: tegra: Implement ->set_dma_mask()
  mmc: sdhci: Let drivers define their DMA mask
  mmc: sdhci-of-esdhc: set DMA snooping based on DMA coherence
  mmc: sdhci: improve ADMA error reporting

Move the static keyword to the front of declaration of
csky_pmu_of_device_ids, and resolve the following compiler
warning that can be seen when building with warnings
enabled (W=1):

arch/csky/kernel/perf_event.c:1340:1: warning:
  ‘static’ is not at beginning of declaration [-Wold-style-declaration]
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Guo Ren <guoren@kernel.org>

Since the enabling and disabling of IRQs within preempt_schedule_irq()
is contained in a need_resched() loop, we don't need the outer arch
code loop.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Guo Ren <guoren@kernel.org>

Pull Documentation/process update from Greg KH:
 "Here are two small Documentation/process/embargoed-hardware-issues.rst
  file updates that missed my previous char/misc pull request.

  The first one adds an Intel representative for the process, and the
  second one cleans up the text a bit more when it comes to how the
  disclosure rules work, as it was a bit confusing to some companies"

* tag 'char-misc-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  Documentation/process: Clarify disclosure rules
  Documentation/process: Volunteer as the ambassador for Intel

Pull more vfs updates from Al Viro:
 "A couple of misc patches"

* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  afs dynroot: switch to simple_dir_operations
  fs/handle.c - fix up kerneldoc

Pull more cifs updates from Steve French:
 "Fixes from the recent SMB3 Test events and Storage Developer
  Conference (held the last two weeks).

  Here are nine smb3 patches including an important patch for debugging
  traces with wireshark, with three patches marked for stable.

  Additional fixes from last week to better handle some newly discovered
  reparse points, and a fix the create/mkdir path for setting the mode
  more atomically (in SMB3 Create security descriptor context), and one
  for path name processing are still being tested so are not included
  here"

* tag '5.4-rc-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  CIFS: Fix oplock handling for SMB 2.1+ protocols
  smb3: missing ACL related flags
  smb3: pass mode bits into create calls
  smb3: Add missing reparse tags
  CIFS: fix max ea value size
  fs/cifs/sess.c: Remove set but not used variable 'capabilities'
  fs/cifs/smb2pdu.c: Make SMB2_notify_init static
  smb3: fix leak in "open on server" perf counter
  smb3: allow decryption keys to be dumped by admin for debugging

The csky_pmu.max_period has type u64, and BIT() can only return
32 bits unsigned long on C-SKY. The initialization for max_period
will be incorrect when count_width is bigger than 32.

Use BIT_ULL()
Signed-off-by: Mao Han <han_mao@c-sky.com>
Signed-off-by: Guo Ren <ren_guo@c-sky.com>

We need set fp zero to let backtrace know the end. The patch fixup perf
callchain panic problem, because backtrace didn't know what is the end
of fp.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Reported-by: Mao Han <han_mao@c-sky.com>

The csky implementation of free_initrd_mem() is an open-coded version of
free_reserved_area() without poisoning.

Remove it and make csky use the generic version of free_initrd_mem().
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Guo Ren <guoren@kernel.org>

Merge active entropy generation updates.

This is admittedly partly "for discussion".  We need to have a way
forward for the boot time deadlocks where user space ends up waiting for
more entropy, but no entropy is forthcoming because the system is
entirely idle just waiting for something to happen.

While this was triggered by what is arguably a user space bug with
GDM/gnome-session asking for secure randomness during early boot, when
they didn't even need any such truly secure thing, the issue ends up
being that our "getrandom()" interface is prone to that kind of
confusion, because people don't think very hard about whether they want
to block for sufficient amounts of entropy.

The approach here-in is to decide to not just passively wait for entropy
to happen, but to start actively collecting it if it is missing.  This
is not necessarily always possible, but if the architecture has a CPU
cycle counter, there is a fair amount of noise in the exact timings of
reasonably complex loads.

We may end up tweaking the load and the entropy estimates, but this
should be at least a reasonable starting point.

As part of this, we also revert the revert of the ext4 IO pattern
improvement that ended up triggering the reported lack of external
entropy.

* getrandom() active entropy waiting:
  Revert "Revert "ext4: make __ext4_get_inode_loc plug""
  random: try to actively add entropy rather than passively wait for it