- 23 Jan, 2013 5 commits
-
-
Lee Jones authored
Kicks the watchdog so charging will not stop. Signed-off-by:Lee Jones <lee.jones@linaro.org>
-
Michel JAOUEN authored
Add AB9540 and AB8505 support to ABx500 BTEMP driver. Signed-off-by:
Rajkumar Kasirajan <rajkumar.kasirajan@stericsson.com> Signed-off-by:
Michel JAOUEN <michel.jaouen@stericsson.com> Reviewed-by:
Marcus COOPER <marcus.xm.cooper@stericsson.com> Reviewed-by:
Jonas ABERG <jonas.aberg@stericsson.com> Tested-by:
-
Hakan Berg authored
Changed conditions for restarting low battery measurements counter and adjusted the interval between measurements to avoid RF burst induced voltage drops, and to shorten time to decide to shut down. Signed-off-by:
Hakan Berg <hakan.berg@stericsson.com> Signed-off-by:
Martin Bergstrom <martin.bergstrom@stericsson.com> Signed-off-by:
-
Henrik Sölver authored
AB8500 refuses to start charging when some types of non standard chargers are connected. This change force the AB to start charging. Signed-off-by:
Henrik Sölver <henrik.solver@stericsson.com> Signed-off-by:
Yvan FILLION <yvan.fillion@stericsson.com> Reviewed-by:
-
Michel JAOUEN authored
AC charger driver for the DB9540 based platforms. Signed-off-by:
Loic Pallardy <loic.pallardy@stericsson.com> Signed-off-by:
-
- 20 Jan, 2013 1 commit
-
-
Andrew Lunn authored
GPLv2+ is not a valid license string. Replace it with one that is. Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
Anton Vorontsov <anton@enomsg.org>
-
- 16 Jan, 2013 17 commits
-
-
Lee Jones authored
As HZ is a full-second, there is little point in rounding it. Let's save a few cycles by using HZ directly. Signed-off-by:
-
Paer-Olof Haakansson authored
When calculating the average current the nominator will overflow when the charging current is high. Signed-off-by:
Par-Olof HAKANSSON <par-olof.hakansson@stericsson.com> Reviewed-by:
-
Marcus Cooper authored
A Legacy USB charger should be handled directly by the charger driver. Signed-off-by:
Karl KOMIEROWSKI <karl.komierowski@stericsson.com> Reviewed-by:
-
Marcus Cooper authored
Cleanup of the ab8500_charger driver. Signed-off-by:
-
Hakan Berg authored
Add support for the battery over-voltage situation Signed-off-by:
-
Hakan Berg authored
BTEMP thermal compensation factor times 10 is applied in two places, probe and get_property. Removed from probe. Signed-off-by:
-
pender01 authored
Round the capacity values for better enduser experience. Signed-off-by:
pender01 <peter.enderborg@stericsson.com> Reviewed-by:
-
Hakan Berg authored
The Travel and Carkit adapter should be handled directly by the charger driver. Signed-off-by:
-
Hakan Berg authored
Ignore the low btemp interrupts for ab8500 3.0 and 3.3 Signed-off-by:
-
Lee Jones authored
The Linux Power Supply framework expects battery temperatures to have a resolution of 0.1 degree Celsius; however, the AB8500 btemp driver supplies a battery temperature resolution of 1 degree Celsius. We therefore have to use a factor 10 on the measured values. Signed-off-by:
-
Rickard Andersson authored
In case of time out error IRQ needs to be disabled otherwise we will get unbalanced enable/disable pairs. Signed-off-by:
Rickard Andersson <rickard.andersson@stericsson.com> Reviewed-by:
-
Marcus Cooper authored
Today the battery recharge is determined with a voltage threshold. This voltage threshold is only valid when the battery is relaxed. In charging algorithm the voltage read is the loaded battery voltage and no compensation is done to get the relaxed voltage. When maintenance charging is not selected, this makes the recharging condition to almost immediately activate when there is a discharge present on the battery. Depending on which vendor the battery comes from this behavior can wear out the battery much faster than normal. The fuelgauge driver is responsible to monitor the actual battery capacity and is able to estimate the remaining capacity. It is better to use the remaining capacity as a limit to determine when battery should be recharged. Signed-off-by:
-
Jonas Aaberg authored
Gracefully handle gpadc conversion errors. Signed-off-by:
Johan BJORNSTEDT <johan.bjornstedt@stericsson.com> Signed-off-by:
-
Jonas Aaberg authored
Doing so provides a greater degree of accuracy when dealing with time-frames between 1us and 20ms. msleep() is only accurate for wake-ups greater than 20ms. Signed-off-by:
-
Lee Jones authored
Add two new work queues to provide USB and AC charger disconnect detection. Signed-off-by:
-
Johan Bjornstedt authored
When enabling the CCEOC irq we might get false interrupt from ab8500-driver due to the latched value will be saved and interpreted as an IRQ when enabled Signed-off-by:
-
Paer-Olof Haakansson authored
Rename the ab8500_power_loss_handling function to a more descriptive name ab8500_enable_disable_sw_fallback Signed-off-by:
Robert Marklund <robert.marklund@stericsson.com> Reviewed-by:
-
- 06 Jan, 2013 17 commits
-
-
Nickolai Zeldovich authored
Avoid accessing vc_tbl_ref[3], which is one past the end of that array, in da9052_determine_vc_tbl_index(), by adjusting the loop bound. (Hint: there is 'i + 1' inside the loop.) Signed-off-by:
Nickolai Zeldovich <nickolai@csail.mit.edu> Signed-off-by:
-
Devendra Naga authored
use devm_kzalloc and no need of error path and unload frees. Signed-off-by:
Devendra Naga <devendra.aaru@gmail.com> Signed-off-by:
-
Kim, Milo authored
Use 'platform_device' in kernel messages rather than i2c client device node. lp8788_update_charger_params() needs additional argument, 'pdev'. Then, remove unnecessary lp8788 private data in lp8788_irq_register(). Signed-off-by:
Milo(Woogyom) Kim <milo.kim@ti.com> Signed-off-by:
-
Kim, Milo authored
The lp8788-charger is a platform driver of lp8788-mfd. The platform device is allocated when mfd_add_devices() is called in lp8788-mfd. On the other hand, 'lp->dev' is the i2c client device. Therefore, this 'platform_device' is a proper parent device in case of resource managed mem alloc and device kernel message. Signed-off-by:
-
Andrew Lunn authored
Some devices, Buffalo Linkstation LS-XHL and LS-CHLv2 for example, power-off by restarting to letting u-boot hold the SoC until the user presses a key. Add a generic driver to implement this. It binds a function to pm_power_off, which calls arm_pm_restart. Signed-off-by:
Michael Walle <michael@walle.cc> Signed-off-by:
-
Andrew Lunn authored
The QNAP NAS boxes have a microcontroller attached to the SoCs second serial port. By sending it a simple command, it will turn the power for the board off. This driver registers a function for pm_power_off to send such a command. Signed-off-by:
-
Kim, Milo authored
Cc: Anton Vorontsov <cbou@mail.ru> Cc: Bryan Wu <cooloney@gmail.com> Cc: Jonathan Cameron <jic23@cam.ac.uk> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by:
Bryan Wu <cooloney@gmail.com> Signed-off-by:
-
Kim, Milo authored
Cc: Anton Vorontsov <cbou@mail.ru> Cc: David Woodhouse <dwmw2@infradead.org> Signed-off-by:
-
Julia Lawall authored
devm_kzalloc should not be followed by kfree, as this results in a double free. The problem was found using the following semantic match (http://coccinelle.lip6.fr/): // <smpl> @@ expression x,e; @@ x = devm_kzalloc(...) ... when != x = e ?-kfree(x,...); // </smpl> Furthermore, in the remove function, the calls to free_irq are moved up to prevent a possible reference in the interrupt handler to resources freed by power_supply_unregister. Signed-off-by:
Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by:
-
Sachin Kamat authored
devm_regulator_get() is device managed and makes error handling and code cleanup simpler. Signed-off-by:
Sachin Kamat <sachin.kamat@linaro.org> Acked-by:
Arun Murthy <arun.murthy@stericsson.com> Acked-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
NeilBrown authored
commit a66f59ba bq27x00_battery: Add support for BQ27425 chip introduced 2 bugs. 1/ 'chip' was set to BQ27425 unconditionally - breaking support for other devices; 2/ BQ27425 does not support cycle count, how the code still tries to get the cycle count for BQ27425, and now does it twice for other chips. Signed-off-by:
NeilBrown <neilb@suse.de> Cc: Saranya Gopal <saranya.gopal@intel.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Ramakrishna Pallala authored
As most of the charger chips come with two kinds of safety features related to timing: 1. Watchdog Timer (interms of seconds/mins) 2. Safety Timer (interms of hours) This patch adds these to fault causes in POWER_SUPPLY_PROP_HEALTH_* enums so that whenever there is either watchdog timeout or safety timer timeout driver could notify the user space accurately about the fault and will also be helpful for debug. Signed-off-by:
Ramakrishna Pallala <ramakrishna.pallala@intel.com> Signed-off-by:
-
Sachin Kamat authored
devm_kzalloc is device managed and makes error handling and code cleanup a bit simpler. Signed-off-by:
-
Sachin Kamat authored
module_i2c_driver() makes the code simpler by eliminating module_init and module_exit calls. Signed-off-by:
-
Sachin Kamat authored
<linux/version.h> is not required here. Signed-off-by:
-
Anton Vorontsov authored
Conflicts: drivers/power/ab8500_bmdata.c
-
Rajanikanth H.V authored
ab8500_fg driver prepares instance list of fuelgauge which is required by btemp driver for battery identification. So make sure that ab8500 fuelgauge list is ready before btemp driver starts. Signed-off-by:
Rajanikanth H.V <rajanikanth.hv@stericsson.com> Acked-by:
-
