Allow powering off SDIO cards and enable runtime PM for eMMC/SD card
devices. Without this, SDIO WLAN devices will not idle.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20211015104720.52240-6-tony@atomide.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Implement PM runtime functions and enable autosuspend.

Note that we save context in probe to avoid restoring invalid context
on the first resume. For system suspend, we have the new PM runtime
functions do most of the work.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20211015104720.52240-5-tony@atomide.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The omap specific registers are at offset 0x100 from base for omap4 and
later, and for omap3 and earlier they are at offset 0. Let's handle also
the earlier SoCs by adding omap_offset.

Note that eventually we should just move to using standard sdhci register
access for the sdhci range with new offsets starting at 0x100.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20211015104720.52240-4-tony@atomide.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In order to start deprecating the custom omap_hsmmc.c in favor of the
generic sdhci-omap driver, we need to add support for voltages for earlier
SoCs.

The PBIAS regulator on omap4 and earlier only supports nominal values of
1.8V and 3.0V, while omap5 and later support nominal values of 1.8V and
3.3V IO voltage.

This gets omap4/5 working with sdhci-omap driver.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20211015104720.52240-3-tony@atomide.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Let's add compatible values for the legacy SoCs so we can continue
deprecating omap_hsmmc in favor of sdhci-omap driver.

For omap5, we want to have a separate compatible from omap4 for the
additional features available on omap5. AFAIK ti81 can just use the
omap4 compatible.

Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20211015104720.52240-2-tony@atomide.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The Winbond MMC driver fails to build on ARCH=m68k so prevent
that build config. Silences these build errors:

../drivers/mmc/host/wbsd.c: In function 'wbsd_request_end':
../drivers/mmc/host/wbsd.c:212:28: error: implicit declaration of function 'claim_dma_lock' [-Werror=implicit-function-declaration]
  212 |                 dmaflags = claim_dma_lock();
../drivers/mmc/host/wbsd.c:215:17: error: implicit declaration of function 'release_dma_lock'; did you mean 'release_task'? [-Werror=implicit-function-declaration]
  215 |                 release_dma_lock(dmaflags);
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211017175949.23838-1-rdunlap@infradead.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

To reset standard tuning circuit completely, after clear ESDHC_MIX_CTRL_EXE_TUNE,
also need to clear bit buffer_read_ready, this operation will finally clear the
USDHC IP internal logic flag execute_tuning_with_clr_buf, make sure the following
normal data transfer will not be impacted by standard tuning logic used before.

Find this issue when do quick SD card insert/remove stress test. During standard
tuning prodedure, if remove SD card, USDHC standard tuning logic can't clear the
internal flag execute_tuning_with_clr_buf. Next time when insert SD card, all
data related commands can't get any data related interrupts, include data transfer
complete interrupt, data timeout interrupt, data CRC interrupt, data end bit interrupt.
Always trigger software timeout issue. Even reset the USDHC through bits in register
SYS_CTRL (0x2C, bit28 reset tuning, bit26 reset data, bit 25 reset command, bit 24
reset all) can't recover this. From the user's point of view, USDHC stuck, SD can't
be recognized any more.

Fixes: d9370424 ("mmc: sdhci-esdhc-imx: reset tuning circuit when power on mmc card")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1634263236-6111-1-git-send-email-haibo.chen@nxp.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

There is no user of this member. Remove the dead code for good.

The removal is dependent on the previous removal of the
struct sdhci_pci_data.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20211014132613.27861-6-andriy.shevchenko@linux.intel.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The last user of this struct gone couple of releases ago.
Remove the dead code for good and encourage people to use
MMC core functionality for that.

The removal is dependent on the previous removal of the
struct sdhci_pci_data.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20211014132613.27861-5-andriy.shevchenko@linux.intel.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The last user of this struct gone a couple of releases ago.
Besides that there were not so many users of this API for
more than 10 years:

1/ The one is Intel Merrifield, that had been added 2016-08-31
   by the commit 3976b038 ("x86/platform/intel-mid: Enable
   SD card detection on Merrifield") and removed 2021-02-11 by
   the commit 4590d98f ("sfi: Remove framework for deprecated
   firmware").

2/ The other is Intel Sunrisepoint related, that had been added
   2015-02-06 by the commit e1bfad6d ("mmc: sdhci-pci: Add
   support for drive strength selection for SPT") and removed
   2017-03-20 by the commit 51ced59c ("mmc: sdhci-pci: Use
   ACPI DSM to get driver strength for some Intel devices").

Effectively this is a revert of the commit 52c506f0 ("mmc:
sdhci-pci: add platform data").
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20211014132613.27861-4-andriy.shevchenko@linux.intel.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

sdhci_card_detect() is not defined anywhere. Remove it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20211014132613.27861-3-andriy.shevchenko@linux.intel.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The analogue of the sdhci_get_cd_nogpio() is used in the sdhci-pci-core
and sdhci-acpi modules. Deduplicate it by moving to sdhci and exporting.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20211014132613.27861-2-andriy.shevchenko@linux.intel.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

There are several error return paths that dereference the null pointer
host because the pointer has not yet been set to a valid value.
Fix this by adding a new out_mmc label and exiting via this label
to avoid the host clean up and hence the null pointer dereference.

Addresses-Coverity: ("Explicit null dereference")
Fixes: 8105c2ab ("mmc: moxart: Fix reference count leaks in moxart_probe")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20211013100052.125461-1-colin.king@canonical.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Intel Merrifield platform had been converted to use ACPI enumeration.
However, the driver missed an update to retrieve card detect GPIO.
Fix it here.

Unfortunately we can't rely on CD GPIO state because there are two
different PCB designs in the wild that are using the opposite card
detection sense and there is no way to distinguish those platforms,
that's why ignore CD GPIO completely and use it only as an event.

Fixes: 4590d98f ("sfi: Remove framework for deprecated firmware")
BugLink: https://github.com/edison-fw/meta-intel-edison/issues/135Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211013201723.52212-2-andriy.shevchenko@linux.intel.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The "msh" pointer is device managed, meaning that memstick_alloc_host()
calls device_initialize() on it.  That means that it can't be free
using kfree() but must instead be freed with memstick_free_host().
Otherwise it leads to a tiny memory leak of device resources.

Fixes: 60fdd931 ("memstick: add support for JMicron jmb38x MemoryStick host controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211011123912.GD15188@kiliSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The issue happens in several error handling paths on two refcounted
object related to the object "host" (dma_chan_rx, dma_chan_tx). In
these paths, the function forgets to decrement one or both objects'
reference count increased earlier by dma_request_chan(), causing
reference count leaks.

Fix it by balancing the refcounts of both objects in some error
handling paths. In correspondence with the changes in moxart_probe(),
IS_ERR() is replaced with IS_ERR_OR_NULL() in moxart_remove() as well.
Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn>
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Link: https://lore.kernel.org/r/20211009041918.28419-1-xiongx18@fudan.edu.cnSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Currently default label of GPIO is assigned to the device name,
when no con_id provided. Instead, let's update it to reflect
what it's about (use already prepared template).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210929111757.52625-2-andriy.shevchenko@linux.intel.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Refactor mmc_gpio_alloc() to drop unneeded indentation level
and double condition. This increases readability of the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210929111757.52625-1-andriy.shevchenko@linux.intel.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The schema defines dependency only of clock-output-names on #clock-cells.
The dependency in opposite direction - requirement of clock-output-names
if #clock-cells is defined - should be explicitly included in the
bindings.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211004151646.73599-1-krzysztof.kozlowski@canonical.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The Microchip PolarFire SoC FPGA DTSI uses Cadence SD/SDIO/eMMC Host
Controller without any additional vendor compatible:

  arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dt.yaml: mmc@20008000: compatible:0: 'cdns,sd4hc' is not one of ['socionext,uniphier-sd4hc']
  arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dt.yaml: mmc@20008000: compatible: ['cdns,sd4hc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210927125044.20046-1-krzysztof.kozlowski@canonical.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

clang-14 complains about a sanity check that always passes when the
page size is 64KB or larger:

drivers/memstick/core/ms_block.c:1739:21: error: result of comparison of constant 65536 with expression of type 'unsigned short' is always false [-Werror,-Wtautological-constant-out-of-range-compare]
        if (msb->page_size > PAGE_SIZE) {
            ~~~~~~~~~~~~~~ ^ ~~~~~~~~~

This is fine, it will still work on all architectures, so just shut
up that warning with a cast.

Fixes: 0ab30494 ("memstick: add support for legacy memorysticks")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210927094520.696665-1-arnd@kernel.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

According to the specification, DLL status has to be locked before using it.
Signed-off-by: Zhenxiong Lai <zhenxiong.lai@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210926092835.146449-1-zhang.lyra@gmail.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

There is a spelling mistake in a pr_info message. Fix it. Also
put msi in capital letters.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210924225111.143112-1-colin.king@canonical.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Describe better which driver applies to which SoC, to make configuring
kernel for Samsung SoC easier.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210924133257.112017-1-krzysztof.kozlowski@canonical.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Nowadays the standard non-removable property should be used, but we
still need to parse the ti,non-removable too. Let's document it as a
deprecated property.

Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210924073441.7835-1-tony@atomide.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Clean up sdhci_calc_timeout() a bit,  and let it set too_big to be true only
when the timeout value required by the eMMC device exceeds the capability of
the host hardware timer.
Signed-off-by: Bean Huo <beanhuo@micron.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210917172727.26834-2-huobean@gmail.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Put a small comment before assigning IRQ_WAKE_THREAD
telling us what is going on.

Cc: Russell King <linux@armlinux.org.uk>
Cc: Yann Gautier <yann.gautier@foss.st.com>
Cc: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210921143359.1738149-1-linus.walleij@linaro.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

ADMA is only available on controller instances that are connected to the
L3 interconnect and are bus mastering capable.

As the MMCHS_HL_HWINFO is in the module registers before omap registers
and sdhci registers, and the omap registers and sdhci registers can be
at different offsets depending on the SoC, let's read MMCHS_HL_HWINFO
directly.

Let's also switch to using device_property_present() while at it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210921110029.21944-6-tony@atomide.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

We need to support the legacy ti,non-removable property too. Let's warn
about the legacy property and mark the device as non-removable.

Naturally all the mainline kernel devicetree files will get updated to use
the standard non-removable property with the sdhci-omap conversion. But we
also have folks updating their kernels with custom devicetree files that
we need to consider.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210921110029.21944-5-tony@atomide.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The sysconfig register is managed in a generic way by PM runtime for us by
the interconnect target module layer code. SDHCI_RESET_ALL also resets the
target module configuration, so we need to restore sysconfig after reset.

Note that there is no need to save and restore sysconfig during PM runtime,
the PM runtime layer will do that for us.

Not sure if this issue is a problem with the current configurations, I
noticed the issue while adding support for older TI SoCs and testing with
wlcore SDIO wlan device.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210921110029.21944-4-tony@atomide.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

We need to restore context in a specified order with HCTL set in two
phases. This is similar to what omap_hsmmc_context_restore() is doing.
Otherwise SDIO can stop working on resume.

And for PM runtime and SDIO cards, we need to also save SYSCTL, IE and
ISE.

This should not be a problem currently, and these patches can be applied
whenever suitable.

Fixes: ee0f3092 ("mmc: sdhci-omap: Add Support for Suspend/Resume")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210921110029.21944-3-tony@atomide.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

If sdhci-omap is configured for an unused device instance and the device
is not set as disabled, we can get a NULL pointer dereference:

Unable to handle kernel NULL pointer dereference at virtual address
00000045
...
(regulator_set_voltage) from [<c07d7008>] (mmc_regulator_set_ocr+0x44/0xd0)
(mmc_regulator_set_ocr) from [<c07e2d80>] (sdhci_set_ios+0xa4/0x490)
(sdhci_set_ios) from [<c07ea690>] (sdhci_omap_set_ios+0x124/0x160)
(sdhci_omap_set_ios) from [<c07c8e94>] (mmc_power_up.part.0+0x3c/0x154)
(mmc_power_up.part.0) from [<c07c9d20>] (mmc_start_host+0x88/0x9c)
(mmc_start_host) from [<c07cad34>] (mmc_add_host+0x58/0x7c)
(mmc_add_host) from [<c07e2574>] (__sdhci_add_host+0xf0/0x22c)
(__sdhci_add_host) from [<c07eaf68>] (sdhci_omap_probe+0x318/0x72c)
(sdhci_omap_probe) from [<c06a39d8>] (platform_probe+0x58/0xb8)

AFAIK we are not seeing this with the devices configured in the mainline
kernel but this can cause issues for folks bringing up their boards.

Fixes: 7d326930 ("mmc: sdhci-omap: Add OMAP SDHCI driver")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210921110029.21944-2-tony@atomide.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

According to JEDEC Spec, there is no need to do tuning under HS400 mode
since the Rx signal is aligned with the DS signal. However, MediaTek's IC
need set its "DS delay" internally to ensure it can latch Rx signal
correctly.

In previous version, We provide an "hs400-ds-delay" in device tree to cover
different chipset/PCB design, and it works fine in most cases.  But, with
the development of process technology and the big VCore voltage scale
range(may have 0.7V/0.6V/0.55V), it is difficult to find a suitable
"hs400-ds-delay" to cover all of IC corner cases(SSSS/TTTT/FFFF). So that
We must have the ability to do hs400 online tuning.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Reviewed-by: Chaotian Jing <chaotian.jing@mediatek.com>
Link: https://lore.kernel.org/r/20210917124803.22871-4-wenbin.mei@mediatek.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This adds a ->execute_hs400_tuning() host callback to enable optional
support for host specific tuning for eMMC HS400 mode. Additionally, share
mmc_get_ext_csd() through the public host headerfile, to allow it to be
used by the host drivers, which is needed to support the HS400 tuning.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Link: https://lore.kernel.org/r/20210917124803.22871-3-wenbin.mei@mediatek.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add hs400 dly3 setting for mtk-sd yaml
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210917124803.22871-2-wenbin.mei@mediatek.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The MODULE_DEVICE_TABLE already creates proper alias for platform
driver.  Having another MODULE_ALIAS causes the alias to be duplicated.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsunhg.com>
Link: https://lore.kernel.org/r/20210916170511.137915-1-krzysztof.kozlowski@canonical.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The recent change ("dt-bindings: mmc: Convert MMC Card binding to a schema")
renamed: Documentation/devicetree/bindings/mmc/mmc-card.txt
to: Documentation/devicetree/bindings/mmc/mmc-card.yaml.

Let's update its cross-reference accordingly.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/820bb7a1d7e0e51cbea72c9bee6bce806427d1f3.1631785820.git.mchehab+huawei@kernel.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>