- 09 Dec, 2015 25 commits
-
-
Peter Chen authored
commit facf47ee upstream. For imx27, it needs three clocks to let the controller work, the old code is wrong, and usbmisc has not included clock handling code any more. Without this patch, it will cause below data abort when accessing usbmisc registers. usbcore: registered new interface driver usb-storage Unhandled fault: external abort on non-linefetch (0x008) at 0xf4424600 pgd = c0004000 [f4424600] *pgd=10000452(bad) Internal error: : 8 [#1] PREEMPT ARM Modules linked in: CPU: 0 PID: 1 Comm: swapper Not tainted 4.1.0-next-20150701-dirty #3089 Hardware name: Freescale i.MX27 (Device Tree Support) task: c7832b60 ti: c783e000 task.ti: c783e000 PC is at usbmisc_imx27_init+0x4c/0xbc LR is at usbmisc_imx27_init+0x40/0xbc pc : [<c03cb5c0>] lr : [<c03cb5b4>] psr: 60000093 sp : c783fe08 ip : 00000000 fp : 00000000 r10: c0576434 r9 : 0000009c r8 : c7a773a0 r7 : 01000000 r6 : 60000013 r5 : c7a776f0 r4 : c7a773f0 r3 : f4424600 r2 : 00000000 r1 : 00000001 r0 : 00000001 Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel Control: 0005317f Table: a0004000 DAC: 00000017 Process swapper (pid: 1, stack limit = 0xc783e190) Stack: (0xc783fe08 to 0xc7840000) Signed-off-by:
Peter Chen <peter.chen@freescale.com> Reported-by:
Fabio Estevam <fabio.estevam@freescale.com> Tested-by:
Shawn Guo <shawnguo@kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Ujfalusi authored
commit 696d8b70 upstream. In case when the interrupt happened for the second eDMA the channel number was incorrectly passed to the client driver. Signed-off-by:
Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
Marek Szyprowski authored
commit 7e312103 upstream. IOMMU-based dma_mmap() implementation lacked proper support for offset parameter used in mmap call (it always assumed that mapping starts from offset zero). This patch adds support for offset parameter to IOMMU-based implementation. Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by:
-
Marek Szyprowski authored
commit 371f0f08 upstream. dma_mmap() function in IOMMU-based dma-mapping implementation lacked a check for valid range of mmap parameters (offset and buffer size), what might have caused access beyond the allocated buffer. This patch fixes this issue. Signed-off-by:
-
Sasha Levin authored
[ Upstream commit 74e98eb0 ] There was no verification that an underlying transport exists when creating a connection, this would cause dereferencing a NULL ptr. It might happen on sockets that weren't properly bound before attempting to send a message, which will cause a NULL ptr deref: [135546.047719] kasan: GPF could be caused by NULL-ptr deref or user memory accessgeneral protection fault: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC KASAN [135546.051270] Modules linked in: [135546.051781] CPU: 4 PID: 15650 Comm: trinity-c4 Not tainted 4.2.0-next-20150902-sasha-00041-gbaa1222-dirty #2527 [135546.053217] task: ffff8800835bc000 ti: ffff8800bc708000 task.ti: ffff8800bc708000 [135546.054291] RIP: __rds_conn_create (net/rds/connection.c:194) [135546.055666] RSP: 0018:ffff8800bc70fab0 EFLAGS: 00010202 [135546.056457] RAX: dffffc0000000000 RBX: 0000000000000f2c RCX: ffff8800835bc000 [135546.057494] RDX: 0000000000000007 RSI: ffff8800835bccd8 RDI: 0000000000000038 [135546.058530] RBP: ffff8800bc70fb18 R08: 0000000000000001 R09: 0000000000000000 [135546.059556] R10: ffffed014d7a3a23 R11: ffffed014d7a3a21 R12: 0000000000000000 [135546.060614] R13: 0000000000000001 R14: ffff8801ec3d0000 R15: 0000000000000000 [135546.061668] FS: 00007faad4ffb700(0000) GS:ffff880252000000(0000) knlGS:0000000000000000 [135546.062836] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b [135546.063682] CR2: 000000000000846a CR3: 000000009d137000 CR4: 00000000000006a0 [135546.064723] Stack: [135546.065048] ffffffffafe2055c ffffffffafe23fc1 ffffed00493097bf ffff8801ec3d0008 [135546.066247] 0000000000000000 00000000000000d0 0000000000000000 ac194a24c0586342 [135546.067438] 1ffff100178e1f78 ffff880320581b00 ffff8800bc70fdd0 ffff880320581b00 [135546.068629] Call Trace: [135546.069028] ? __rds_conn_create (include/linux/rcupdate.h:856 net/rds/connection.c:134) [135546.069989] ? rds_message_copy_from_user (net/rds/message.c:298) [135546.071021] rds_conn_create_outgoing (net/rds/connection.c:278) [135546.071981] rds_sendmsg (net/rds/send.c:1058) [135546.072858] ? perf_trace_lock (include/trace/events/lock.h:38) [135546.073744] ? lockdep_init (kernel/locking/lockdep.c:3298) [135546.074577] ? rds_send_drop_to (net/rds/send.c:976) [135546.075508] ? __might_fault (./arch/x86/include/asm/current.h:14 mm/memory.c:3795) [135546.076349] ? __might_fault (mm/memory.c:3795) [135546.077179] ? rds_send_drop_to (net/rds/send.c:976) [135546.078114] sock_sendmsg (net/socket.c:611 net/socket.c:620) [135546.078856] SYSC_sendto (net/socket.c:1657) [135546.079596] ? SYSC_connect (net/socket.c:1628) [135546.080510] ? trace_dump_stack (kernel/trace/trace.c:1926) [135546.081397] ? ring_buffer_unlock_commit (kernel/trace/ring_buffer.c:2479 kernel/trace/ring_buffer.c:2558 kernel/trace/ring_buffer.c:2674) [135546.082390] ? trace_buffer_unlock_commit (kernel/trace/trace.c:1749) [135546.083410] ? trace_event_raw_event_sys_enter (include/trace/events/syscalls.h:16) [135546.084481] ? do_audit_syscall_entry (include/trace/events/syscalls.h:16) [135546.085438] ? trace_buffer_unlock_commit (kernel/trace/trace.c:1749) [135546.085515] rds_ib_laddr_check(): addr 36.74.25.172 ret -99 node type -1 Acked-by:
Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by:
Sasha Levin <sasha.levin@oracle.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Jason Wang authored
[ Upstream commit 48900cb6 ] virtio declares support for NETIF_F_FRAGLIST, but assumes that there are at most MAX_SKB_FRAGS + 2 fragments which isn't always true with a fraglist. A longer fraglist in the skb will make the call to skb_to_sgvec overflow the sg array, leading to memory corruption. Drop NETIF_F_FRAGLIST so we only get what we can handle. Cc: Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
Jason Wang <jasowang@redhat.com> Acked-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit d69bbf88 ] Only cpu seeing dst refcount going to 0 can safely dereference dst->flags. Otherwise an other cpu might already have freed the dst. Fixes: 27b75c95 ("net: avoid RCU for NOCACHE dst") Reported-by:
Greg Thelen <gthelen@google.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Francesco Ruggeri authored
[ Upstream commit 30f7ea1c ] There is a race conditions between packet_notifier and packet_bind{_spkt}. It happens if packet_notifier(NETDEV_UNREGISTER) executes between the time packet_bind{_spkt} takes a reference on the new netdevice and the time packet_do_bind sets po->ifindex. In this case the notification can be missed. If this happens during a dev_change_net_namespace this can result in the netdevice to be moved to the new namespace while the packet_sock in the old namespace still holds a reference on it. When the netdevice is later deleted in the new namespace the deletion hangs since the packet_sock is not found in the new namespace' &net->packet.sklist. It can be reproduced with the script below. This patch makes packet_do_bind check again for the presence of the netdevice in the packet_sock's namespace after the synchronize_net in unregister_prot_hook. More in general it also uses the rcu lock for the duration of the bind to stop dev_change_net_namespace/rollback_registered_many from going past the synchronize_net following unlist_netdevice, so that no NETDEV_UNREGISTER notifications can happen on the new netdevice while the bind is executing. In order to do this some code from packet_bind{_spkt} is consolidated into packet_do_dev. import socket, os, time, sys proto=7 realDev='em1' vlanId=400 if len(sys.argv) > 1: vlanId=int(sys.argv[1]) dev='vlan%d' % vlanId os.system('taskset -p 0x10 %d' % os.getpid()) s = socket.socket(socket.PF_PACKET, socket.SOCK_RAW, proto) os.system('ip link add link %s name %s type vlan id %d' % (realDev, dev, vlanId)) os.system('ip netns add dummy') pid=os.fork() if pid == 0: # dev should be moved while packet_do_bind is in synchronize net os.system('taskset -p 0x20000 %d' % os.getpid()) os.system('ip link set %s netns dummy' % dev) os.system('ip netns exec dummy ip link del %s' % dev) s.close() sys.exit(0) time.sleep(.004) try: s.bind(('%s' % dev, proto+1)) except: print 'Could not bind socket' s.close() os.system('ip netns del dummy') sys.exit(0) os.waitpid(pid, 0) s.close() os.system('ip netns del dummy') sys.exit(0) Signed-off-by:
Francesco Ruggeri <fruggeri@arista.com> Signed-off-by:
-
WANG Cong authored
[ Upstream commit 4ee3bd4a ] This fixes the following lockdep warning: [ INFO: inconsistent lock state ] 4.3.0-rc7+ #1197 Not tainted --------------------------------- inconsistent {IN-SOFTIRQ-R} -> {SOFTIRQ-ON-W} usage. sysctl/1019 [HC0[0]:SC0[0]:HE1:SE1] takes: (&(&net->ipv4.ip_local_ports.lock)->seqcount){+.+-..}, at: [<ffffffff81921de7>] ipv4_local_port_range+0xb4/0x12a {IN-SOFTIRQ-R} state was registered at: [<ffffffff810bd682>] __lock_acquire+0x2f6/0xdf0 [<ffffffff810be6d5>] lock_acquire+0x11c/0x1a4 [<ffffffff818e599c>] inet_get_local_port_range+0x4e/0xae [<ffffffff8166e8e3>] udp_flow_src_port.constprop.40+0x23/0x116 [<ffffffff81671cb9>] vxlan_xmit_one+0x219/0xa6a [<ffffffff81672f75>] vxlan_xmit+0xa6b/0xaa5 [<ffffffff817f2deb>] dev_hard_start_xmit+0x2ae/0x465 [<ffffffff817f35ed>] __dev_queue_xmit+0x531/0x633 [<ffffffff817f3702>] dev_queue_xmit_sk+0x13/0x15 [<ffffffff818004a5>] neigh_resolve_output+0x12f/0x14d [<ffffffff81959cfa>] ip6_finish_output2+0x344/0x39f [<ffffffff8195bf58>] ip6_finish_output+0x88/0x8e [<ffffffff8195bfef>] ip6_output+0x91/0xe5 [<ffffffff819792ae>] dst_output_sk+0x47/0x4c [<ffffffff81979392>] NF_HOOK_THRESH.constprop.30+0x38/0x82 [<ffffffff8197981e>] mld_sendpack+0x189/0x266 [<ffffffff8197b28b>] mld_ifc_timer_expire+0x1ef/0x223 [<ffffffff810de581>] call_timer_fn+0xfb/0x28c [<ffffffff810ded1e>] run_timer_softirq+0x1c7/0x1f1 Fixes: b8f1a556 ("udp: Add function to make source port for UDP tunnels") Cc: Tom Herbert <tom@herbertland.com> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
Sabrina Dubroca authored
[ Upstream commit 2a189f9e ] In ipv6_add_dev, when addrconf_sysctl_register fails, we do not clean up the dev_snmp6 entry that we have already registered for this device. Call snmp6_unregister_dev in this case. Fixes: a317a2f1 ("ipv6: fail early when creating netdev named all or default") Reported-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
Sabrina Dubroca <sd@queasysnail.net> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 8fa677d2 ] Under low memory conditions, tcp_sk_init() and icmp_sk_init() can both iterate on all possible cpus and call inet_ctl_sock_destroy(), with eventual NULL pointer. Signed-off-by:
-
Martin Habets authored
[ Upstream commit b2663a4f ] When the IP stack passes SKBs the sfc driver puts them in 2 different TX queues (called partners), one for checksummed and one for not checksummed. If the SKB has xmit_more set the driver will delay pushing the work to the NIC. When later it does decide to push the buffers this patch ensures it also pushes the partner queue, if that also has any delayed work. Before this fix the work in the partner queue would be left for a long time and cause a netdev watchdog. Fixes: 70b33fb0 ("sfc: add support for skb->xmit_more") Reported-by:
Jianlin Shi <jishi@redhat.com> Signed-off-by:
Martin Habets <mhabets@solarflare.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 4ece9009 ] sit0 device allocates its percpu storage twice : - One time in ipip6_tunnel_init() - One time in ipip6_fb_tunnel_init() Thus we leak 48 bytes per possible cpu per network namespace dismantle. ipip6_fb_tunnel_init() can be much simpler and does not return an error, and should be called after register_netdev() Note that ipip6_tunnel_clone_6rd() also needs to be called after register_netdev() (calling ipip6_tunnel_init()) Fixes: ebe084aa ("sit: Use ipip6_tunnel_init as the ndo_init function.") Signed-off-by:
-
Ani Sinha authored
[ Upstream commit 44f49dd8 ] Fixes the following kernel BUG : BUG: using __this_cpu_add() in preemptible [00000000] code: bash/2758 caller is __this_cpu_preempt_check+0x13/0x15 CPU: 0 PID: 2758 Comm: bash Tainted: P O 3.18.19 #2 ffffffff8170eaca ffff880110d1b788 ffffffff81482b2a 0000000000000000 0000000000000000 ffff880110d1b7b8 ffffffff812010ae ffff880007cab800 ffff88001a060800 ffff88013a899108 ffff880108b84240 ffff880110d1b7c8 Call Trace: [<ffffffff81482b2a>] dump_stack+0x52/0x80 [<ffffffff812010ae>] check_preemption_disabled+0xce/0xe1 [<ffffffff812010d4>] __this_cpu_preempt_check+0x13/0x15 [<ffffffff81419d60>] ipmr_queue_xmit+0x647/0x70c [<ffffffff8141a154>] ip_mr_forward+0x32f/0x34e [<ffffffff8141af76>] ip_mroute_setsockopt+0xe03/0x108c [<ffffffff810553fc>] ? get_parent_ip+0x11/0x42 [<ffffffff810e6974>] ? pollwake+0x4d/0x51 [<ffffffff81058ac0>] ? default_wake_function+0x0/0xf [<ffffffff810553fc>] ? get_parent_ip+0x11/0x42 [<ffffffff810613d9>] ? __wake_up_common+0x45/0x77 [<ffffffff81486ea9>] ? _raw_spin_unlock_irqrestore+0x1d/0x32 [<ffffffff810618bc>] ? __wake_up_sync_key+0x4a/0x53 [<ffffffff8139a519>] ? sock_def_readable+0x71/0x75 [<ffffffff813dd226>] do_ip_setsockopt+0x9d/0xb55 [<ffffffff81429818>] ? unix_seqpacket_sendmsg+0x3f/0x41 [<ffffffff813963fe>] ? sock_sendmsg+0x6d/0x86 [<ffffffff813959d4>] ? sockfd_lookup_light+0x12/0x5d [<ffffffff8139650a>] ? SyS_sendto+0xf3/0x11b [<ffffffff810d5738>] ? new_sync_read+0x82/0xaa [<ffffffff813ddd19>] compat_ip_setsockopt+0x3b/0x99 [<ffffffff813fb24a>] compat_raw_setsockopt+0x11/0x32 [<ffffffff81399052>] compat_sock_common_setsockopt+0x18/0x1f [<ffffffff813c4d05>] compat_SyS_setsockopt+0x1a9/0x1cf [<ffffffff813c4149>] compat_SyS_socketcall+0x180/0x1e3 [<ffffffff81488ea1>] cstar_dispatch+0x7/0x1e Signed-off-by:
Ani Sinha <ani@arista.com> Acked-by:
-
Phil Reid authored
[ Upstream commit e6dbe1eb ] priv->hwts_*_en indicate if timestamping is enabled/disabled at run time. But priv->dma_cap.time_stamp and priv->dma_cap.atime_stamp indicates HW is support for PTPv1/PTPv2. Signed-off-by:
Phil Reid <preid@electromag.com.au> Acked-by:
Richard Cochran <richardcochran@gmail.com> Signed-off-by:
-
Jon Paul Maloy authored
[ Upstream commit 5cbb28a4 ] Testing of the new UDP bearer has revealed that reception of NAME_DISTRIBUTOR, LINK_PROTOCOL/RESET and LINK_PROTOCOL/ACTIVATE message buffers is not prepared for the case that those may be non-linear. We now linearize all such buffers before they are delivered up to the generic reception layer. In order for the commit to apply cleanly to 'net' and 'stable', we do the change in the function tipc_udp_recv() for now. Later, we will post a commit to 'net-next' moving the linearization to generic code, in tipc_named_rcv() and tipc_link_proto_rcv(). Fixes: commit d0f91938 ("tipc: add ip/udp media type") Signed-off-by:
Jon Maloy <jon.maloy@ericsson.com> Signed-off-by:
-
Carol L Soto authored
[ Upstream commit c02b0501 ] When doing memcpy/memset of EQEs, we should use sizeof struct mlx4_eqe as the base size and not caps.eqe_size which could be bigger. If caps.eqe_size is bigger than the struct mlx4_eqe then we corrupt data in the master context. When using a 64 byte stride, the memcpy copied over 63 bytes to the slave_eq structure. This resulted in copying over the entire eqe of interest, including its ownership bit -- and also 31 bytes of garbage into the next WQE in the slave EQ -- which did NOT include the ownership bit (and therefore had no impact). However, once the stride is increased to 128, we are overwriting the ownership bits of *three* eqes in the slave_eq struct. This results in an incorrect ownership bit for those eqes, which causes the eq to seem to be full. The issue therefore surfaced only once 128-byte EQEs started being used in SRIOV and (overarchitectures that have 128/256 byte cache-lines such as PPC) - e.g after commit 77507aa2 "net/mlx4_core: Enable CQE/EQE stride support". Fixes: 08ff3235 ('mlx4: 64-byte CQE/EQE support') Signed-off-by:
Carol L Soto <clsoto@linux.vnet.ibm.com> Signed-off-by:
Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by:
-
Sowmini Varadhan authored
[ Upstream commit 8ce675ff ] Either of pskb_pull() or pskb_trim() may fail under low memory conditions. If rds_tcp_data_recv() ignores such failures, the application will receive corrupted data because the skb has not been correctly carved to the RDS datagram size. Avoid this by handling pskb_pull/pskb_trim failure in the same manner as the skb_clone failure: bail out of rds_tcp_data_recv(), and retry via the deferred call to rds_send_worker() that gets set up on ENOMEM from rds_tcp_read_sock() Signed-off-by:
Sowmini Varadhan <sowmini.varadhan@oracle.com> Acked-by:
-
Alexander Duyck authored
[ Upstream commit c2229fe1 ] We were computing the child index in cases where the key value we were looking for was actually less than the base key of the tnode. As a result we were getting incorrect index values that would cause us to skip over some children. To fix this I have added a test that will force us to use child index 0 if the key we are looking for is less than the key of the current tnode. Fixes: 8be33e95 ("fib_trie: Fib walk rcu should take a tnode and key instead of a trie and a leaf") Reported-by:
Brian Rak <brak@gameservers.com> Signed-off-by:
Alexander Duyck <aduyck@mirantis.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 7e3b6e74 ] gre_gso_segment() chokes if SIT frames were aggregated by GRO engine. Fixes: 61c1db7f ("ipv6: sit: add GSO/TSO support") Signed-off-by:
-
Guillaume Nault authored
[ Upstream commit 1acea4f6 ] We can't rely on PPPOX_ZOMBIE to decide whether to clear po->pppoe_dev. PPPOX_ZOMBIE can be set by pppoe_disc_rcv() even when po->pppoe_dev is NULL. So we have no guarantee that (sk->sk_state & PPPOX_ZOMBIE) implies (po->pppoe_dev != NULL). Since we're releasing a PPPoE socket, we want to release the pppoe_dev if it exists and reset sk_state to PPPOX_DEAD, no matter the previous value of sk_state. So we can just check for po->pppoe_dev and avoid any assumption on sk->sk_state. Fixes: 2b018d57 ("pppoe: drop PPPOX_ZOMBIEs in pppoe_release") Signed-off-by:
Guillaume Nault <g.nault@alphalink.fr> Signed-off-by:
-
Jason Wang authored
[ Upstream commit f23d538b ] We don't have fraglist support in TAP_FEATURES. This will lead software segmentation of gro skb with frag list. Fixes by having frag list support in TAP_FEATURES. With this patch single session of netperf receiving were restored from about 5Gb/s to about 12Gb/s on mlx4. Fixes a567dd62 ("macvtap: simplify usage of tap_features") Cc: Vlad Yasevich <vyasevic@redhat.com> Cc: Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
-
Bjørn Mork authored
[ Upstream commit 0db65fcf ] New device IDs shamelessly lifted from the vendor driver. Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Jon Paul Maloy authored
[ Upstream commit 45c8b7b1 ] The current code for message reassembly is erroneously assuming that the the first arriving fragment buffer always is linear, and then goes ahead resetting the fragment list of that buffer in anticipation of more arriving fragments. However, if the buffer already happens to be non-linear, we will inadvertently drop the already attached fragment list, and later on trig a BUG() in __pskb_pull_tail(). We see this happen when running fragmented TIPC multicast across UDP, something made possible since commit d0f91938 ("tipc: add ip/udp media type") We fix this by not resetting the fragment list when the buffer is non- linear, and by initiatlizing our private fragment list tail pointer to the tail of the existing fragment list. Fixes: commit d0f91938 ("tipc: add ip/udp media type") Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit 50010c20 ] This is decrementing the pointer, instead of the value stored in the pointer. KASan detects it as an out of bounds reference. Reported-by:
"Berry Cheng 程君(成淼)" <chengmiao.cj@alibaba-inc.com> Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
- 09 Nov, 2015 15 commits
-
-
Greg Kroah-Hartman authored
-
Dong Aisheng authored
commit 89c1a8cf upstream. cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios should be changed to GPIO_ACTIVE_HIGH. Otherwise, the SD may not work properly due to wrong polarity inversion specified in DT after switch to common parsing function mmc_of_parse(). Signed-off-by:
Dong Aisheng <aisheng.dong@freescale.com> Acked-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Greg Kroah-Hartman authored
Fixes the backport of 0b34a166 upstream Commit 0b34a166 "x86/xen: Support kexec/kdump in HVM guests by doing a soft reset" has been added to the 4.2-stable tree" needed to correct the CONFIG variable, as CONFIG_KEXEC_CORE only showed up in 4.3. Reported-by:
David Vrabel <david.vrabel@citrix.com> Reported-by:
Luis Henriques <luis.henriques@canonical.com> Signed-off-by:
-
Soeren Grunewald authored
commit be32c0cf upstream. The Exar XR17V358 can also be combined with a XR17V354 chip to act as a single 12 port chip. This works the same way as the combining two XR17V358 chips. But the reported device id then is 0x4358. Signed-off-by:
Soeren Grunewald <soeren.grunewald@desy.de> Signed-off-by:
-
Mika Westerberg authored
commit 78e1c896 upstream. The Intel Baytrail pinctrl driver implements irqchip callbacks which are called with desc->lock raw_spinlock held. In mainline this is fine because spinlock resolves to raw_spinlock. However, running the same code in -rt we get: BUG: sleeping function called from invalid context at kernel/locking/rtmutex.c:917 in_atomic(): 1, irqs_disabled(): 1, pid: 0, name: swapper/0 Preemption disabled at:[<ffffffff81092e9f>] cpu_startup_entry+0x17f/0x480 CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.1.5-rt5 #13 ... Call Trace: <IRQ> [<ffffffff816283c6>] dump_stack+0x4a/0x61 [<ffffffff81077e17>] ___might_sleep+0xe7/0x170 [<ffffffff8162d6cf>] rt_spin_lock+0x1f/0x50 [<ffffffff812e3b88>] byt_gpio_clear_triggering+0x38/0x60 [<ffffffff812e3bc1>] byt_irq_mask+0x11/0x20 [<ffffffff810a7013>] handle_level_irq+0x83/0x150 [<ffffffff810a3457>] generic_handle_irq+0x27/0x40 [<ffffffff812e3a5f>] byt_gpio_irq_handler+0x7f/0xc0 [<ffffffff810050aa>] handle_irq+0xaa/0x190 ... This is because in -rt spinlocks are preemptible so taking the driver private spinlock in irqchip callbacks causes might_sleep() to trigger. In order to keep -rt happy but at the same time make sure that register accesses get serialized, convert the driver to use raw_spinlock instead. Also shorten the critical section a bit in few places. Suggested-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by:
-
Mika Westerberg authored
commit 39ce8150 upstream. There is a hardware issue in Intel Baytrail where concurrent GPIO register access might result reads of 0xffffffff and writes might get dropped completely. Prevent this from happening by taking the serializing lock in all places where it is possible that more than one thread might be accessing the hardware concurrently. Signed-off-by:
-
Minchan Kim authored
commit 47aee4d8 upstream. Use is_zero_pfn() on pteval only after pte_present() check on pteval (It might be better idea to introduce is_zero_pte() which checks pte_present() first). Otherwise when working on a swap or migration entry and if pte_pfn's result is equal to zero_pfn by chance, we lose user's data in __collapse_huge_page_copy(). So if you're unlucky, the application segfaults and finally you could see below message on exit: BUG: Bad rss-counter state mm:ffff88007f099300 idx:2 val:3 Fixes: ca0984ca ("mm: incorporate zero pages into transparent huge pages") Signed-off-by:
Minchan Kim <minchan@kernel.org> Reviewed-by:
Andrea Arcangeli <aarcange@redhat.com> Acked-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Mel Gorman <mgorman@suse.de> Acked-by:
Vlastimil Babka <vbabka@suse.cz> Cc: Hugh Dickins <hughd@google.com> Cc: Rik van Riel <riel@redhat.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Thomas Hellstrom authored
commit 54c12bc3 upstream. If user space calls unreference on a user_dmabuf it will typically kill the struct ttm_base_object member which is responsible for the user-space visibility. However the dmabuf part may still be alive and refcounted. In some situations, like for shared guest-backed surface referencing/opening, the driver may try to reference the struct ttm_base_object member again, causing an immediate kernel warning and a later kernel NULL pointer dereference. Fix this by always maintaining a reference on the struct ttm_base_object member, in situations where it might subsequently be referenced. Signed-off-by:
Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by:
Brian Paul <brianp@vmware.com> Reviewed-by:
Sinclair Yeh <syeh@vmware.com> Signed-off-by:
-
Keith Busch authored
commit 0dfc70c3 upstream. Resources are reallocated for requeued commands, so unmap and release the iod for the failed command. It's a pretty bad memory leak and causes a kernel hang if you remove a drive because of a busy dma pool. You'll get messages spewing like this: nvme 0000:xx:xx.x: dma_pool_destroy prp list 256, ffff880420dec000 busy and lock up pci and the driver since removal never completes while holding a lock. Signed-off-by:
Keith Busch <keith.busch@intel.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Will Deacon authored
commit 589cb22b upstream. If the STXR instruction fails in the SWP emulation code, we leave *data overwritten with the loaded value, therefore corrupting the data written by a subsequent, successful attempt. This patch re-jigs the code so that we only write back to *data once we know that the update has happened. Fixes: bd35a4ad ("arm64: Port SWP/SWPB emulation support from arm") Reported-by:
Shengjiu Wang <shengjiu.wang@freescale.com> Reported-by:
Vladimir Murzin <vladimir.murzin@arm.com> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Lorenzo Pieralisi authored
commit e13d918a upstream. Commit dd006da2 ("arm64: mm: increase VA range of identity map") introduced a mechanism to extend the virtual memory map range to support arm64 systems with system RAM located at very high offset, where the identity mapping used to enable/disable the MMU requires additional translation levels to map the physical memory at an equal virtual offset. The kernel detects at boot time the tcr_el1.t0sz value required by the identity mapping and sets-up the tcr_el1.t0sz register field accordingly, any time the identity map is required in the kernel (ie when enabling the MMU). After enabling the MMU, in the cold boot path the kernel resets the tcr_el1.t0sz to its default value (ie the actual configuration value for the system virtual address space) so that after enabling the MMU the memory space translated by ttbr0_el1 is restored as expected. Commit dd006da2 ("arm64: mm: increase VA range of identity map") also added code to set-up the tcr_el1.t0sz value when the kernel resumes from low-power states with the MMU off through cpu_resume() in order to effectively use the identity mapping to enable the MMU but failed to add the code required to restore the tcr_el1.t0sz to its default value, when the core returns to the kernel with the MMU enabled, so that the kernel might end up running with tcr_el1.t0sz value set-up for the identity mapping which can be lower than the value required by the actual virtual address space, resulting in an erroneous set-up. This patchs adds code in the resume path that restores the tcr_el1.t0sz default value upon core resume, mirroring this way the cold boot path behaviour therefore fixing the issue. Cc: Catalin Marinas <catalin.marinas@arm.com> Fixes: dd006da2 ("arm64: mm: increase VA range of identity map") Acked-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by:
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by:
James Morse <james.morse@arm.com> Signed-off-by:
-
Sudeep Holla authored
commit af391b15 upstream. This patch renames __cpu_suspend to cpu_suspend so that it's aligned with ARM32. It also removes the redundant wrapper created. This is in preparation to implement generic PSCI system suspend using the cpu_{suspend,resume} which now has the same interface on both ARM and ARM64. Cc: Mark Rutland <mark.rutland@arm.com> Reviewed-by:
Ashwin Chaugule <ashwin.chaugule@linaro.org> Signed-off-by:
Sudeep Holla <sudeep.holla@arm.com> Signed-off-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
-
Srinivas Pandruvada authored
commit 8e601a9f upstream. This is a workaround for KNL platform, where in some cases MPERF counter will not have updated value before next read of MSR_IA32_MPERF. In this case divide by zero will occur. This change ignores current sample for busy calculation in this case. Fixes: b34ef932 (intel_pstate: Knights Landing support) Signed-off-by:
Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Acked-by:
Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Doron Tsur authored
commit 0ca81a28 upstream. ib_send_cm_sidr_rep could sometimes erase the node from the sidr (depending on errors in the process). Since ib_send_cm_sidr_rep is called both from cm_sidr_req_handler and cm_destroy_id, cm_id_priv could be either erased from the rb_tree twice or not erased at all. Fixing that by making sure it's erased only once before freeing cm_id_priv. Fixes: a977049d ('[PATCH] IB: Add the kernel CM implementation') Signed-off-by:
Doron Tsur <doront@mellanox.com> Signed-off-by:
Matan Barak <matanb@mellanox.com> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Christian Engelmayer authored
commit 0f89abf5 upstream. Commit 8eb93459 ("btrfs: check unsupported filters in balance arguments") adds a jump to exit label out_bargs in case the argument check fails. At this point in addition to the bargs memory, the memory for struct btrfs_balance_control has already been allocated. Ownership of bctl is passed to btrfs_balance() in the good case, thus the memory is not freed due to the introduced jump. Make sure that the memory gets freed in any case as necessary. Detected by Coverity CID 1328378. Signed-off-by:
Christian Engelmayer <cengelma@gmx.at> Reviewed-by:
David Sterba <dsterba@suse.com> Signed-off-by:
Chris Mason <clm@fb.com> Signed-off-by:
-
