Expose IB diagnostic hardware counters.
The counters count IB events and are applicable for IB and RoCE.

The counters can be divided into two groups, per device and per port.
Device counters are always exposed.
Port counters are exposed only if the firmware supports per port counters.

rq_num_dup and sq_num_to are only exposed if we have firmware support
for them, if we do, we expose them per device and per port.
rq_num_udsdprd and num_cqovf are device only counters.

rq - denotes responder.
sq - denotes requester.

|-----------------------|---------------------------------------|
|	Name		|	Description			|
|-----------------------|---------------------------------------|
|rq_num_lle		| Number of local length errors		|
|-----------------------|---------------------------------------|
|sq_num_lle		| number of local length errors		|
|-----------------------|---------------------------------------|
|rq_num_lqpoe		| Number of local QP operation errors	|
|-----------------------|---------------------------------------|
|sq_num_lqpoe		| Number of local QP operation errors	|
|-----------------------|---------------------------------------|
|rq_num_lpe		| Number of local protection errors	|
|-----------------------|---------------------------------------|
|sq_num_lpe		| Number of local protection errors	|
|-----------------------|---------------------------------------|
|rq_num_wrfe		| Number of CQEs with error		|
|-----------------------|---------------------------------------|
|sq_num_wrfe		| Number of CQEs with error		|
|-----------------------|---------------------------------------|
|sq_num_mwbe		| Number of Memory Window bind errors	|
|-----------------------|---------------------------------------|
|sq_num_bre		| Number of bad response errors		|
|-----------------------|---------------------------------------|
|sq_num_rire		| Number of Remote Invalid request	|
|			| errors				|
|-----------------------|---------------------------------------|
|rq_num_rire		| Number of Remote Invalid request	|
|			| errors				|
|-----------------------|---------------------------------------|
|sq_num_rae		| Number of remote access errors	|
|-----------------------|---------------------------------------|
|rq_num_rae		| Number of remote access errors	|
|-----------------------|---------------------------------------|
|sq_num_roe		| Number of remote operation errors	|
|-----------------------|---------------------------------------|
|sq_num_tree		| Number of transport retries exceeded	|
|			| errors				|
|-----------------------|---------------------------------------|
|sq_num_rree		| Number of RNR NAK retries exceeded	|
|			| errors				|
|-----------------------|---------------------------------------|
|rq_num_rnr		| Number of RNR NAKs sent		|
|-----------------------|---------------------------------------|
|sq_num_rnr		| Number of RNR NAKs received		|
|-----------------------|---------------------------------------|
|rq_num_oos		| Number of Out of Sequence requests	|
|			| received				|
|-----------------------|---------------------------------------|
|sq_num_oos		| Number of Out of Sequence NAKs	|
|			| received				|
|-----------------------|---------------------------------------|
|rq_num_udsdprd		| Number of UD packets silently		|
|			| discarded on the Receive Queue due to	|
|			| lack of receive descriptor		|
|-----------------------|---------------------------------------|
|rq_num_dup		| Number of duplicate requests received	|
|-----------------------|---------------------------------------|
|sq_num_to		| Number of time out received		|
|-----------------------|---------------------------------------|
|num_cqovf		| Number of CQ overflows		|
|-----------------------|---------------------------------------|
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Add a function to query diagnostics counters from the firmware.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Add a bit that indicates if the firmware supports per port
diagnostic counters.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Portmapper messages are short and do not occupy more than 512 bytes.
Lower portmapper message size to 512 bytes. This change significantly
reduces the amount of memory needed when trying to establish a large
number of connections simultaneously. The old value is based on page
size.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Decouple SG support from HW ability to do UD checksum.
This coupling is for historical reasons and removed with 'commit
ec5f0615 ("net: Kill link between CSUM and SG features.")'

During driver load it is assumed that device does not supports SG. The
final decision is taken after creating UD QP based on device capability.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

We allocate a small tracking structure as part of mlx4_ib_resize_cq().
However, we don't need to use GFP_ATOMIC -- immediately after the
allocation, we call mlx4_cq_resize(), which allocates a command
mailbox with GFP_KERNEL and then sleeps on a firmware command, so we
better not be in an atomic context.

This actually has a real impact, because when this GFP_ATOMIC
allocation fails (and GFP_ATOMIC does fail in practice) then a
userspace consumer resizing a CQ will get a spurious failure that we
can easily avoid.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

There is a strict policy in the Linux kernel that new drivers must be
disabled by default. Hence leave out the "default m" line from Kconfig.

Fixes: f48ad614 ("IB/hfi1: Move driver out of staging")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Jubin John <jubin.john@intel.com>
Cc: Dennis Dalessandro <dennis.dalessandro@intel.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: <stable@vger.kernel.org> # v4.7+
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

There is a strict policy in the Linux kernel that new drivers must be
disabled by default. Hence leave out the "default m" line from Kconfig.

Fixes: 0194621b ("IB/rdmavt: Create module framework and handle driver registration")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Jubin John <jubin.john@intel.com>
Cc: Dennis Dalessandro <dennis.dalessandro@intel.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Doug Ledford <dledford@redhat.com>

Pull UDF fixes and a reiserfs fix from Jan Kara:
 "A couple of udf fixes (most notably a bug in parsing UDF partitions
  which led to inability to mount recent Windows installation media) and
  a reiserfs fix for handling kstrdup failure"

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  reiserfs: check kstrdup failure
  udf: Use correct partition reference number for metadata
  udf: Use IS_ERR when loading metadata mirror file entry
  udf: Don't BUG on missing metadata partition descriptor

Pull dmaengine fixes from Vinod Koul:
 "Some fixes has piled up, so time to send them upstream.

  These fixes include:
   - at_xdmac fixes for residue and other stuff
   - update MAINTAINERS for dma dt bindings
   - mv_xor fix for incorrect offset"

* tag 'dmaengine-fix-4.7-rc4' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: mv_xor: Fix incorrect offset in dma_map_page()
  dmaengine: at_xdmac: double FIFO flush needed to compute residue
  dmaengine: at_xdmac: fix residue corruption
  dmaengine: at_xdmac: align descriptors on 64 bits
  MAINTAINERS: Add file patterns for dma device tree bindings

Pull ARM SoC fixes from Olof Johansson:
 "Another batch of fixes for ARM SoC platforms.  Most are smaller fixes.

  Two areas that are worth pointing out are:

   - OMAP had a handful of changes to voltage specs that caused a bit of
     churn, most of volume of change in this branch is due to this.

   - There are a couple of _rcuidle fixes from Paul that touch common
     code and came in through the OMAP tree since they were the ones who
     saw the problems.

 The rest is smaller changes across a handful of platforms"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (36 commits)
  ARM: dts: STi: stih407-family: Disable reserved-memory co-processor nodes
  ARM: dts: am437x-sk-evm: Reduce i2c0 bus speed for tps65218
  ARM: OMAP2+: timer: add probe for clocksources
  ARM: OMAP1: fix ams-delta FIQ handler to work with sparse IRQ
  memory: omap-gpmc: Fix omap gpmc EXTRADELAY timing
  arm: Use _rcuidle for smp_cross_call() tracepoints
  MAINTAINERS: Add myself as reviewer of ARM FSL/NXP
  ARM: OMAP: DRA7: powerdomain data: Remove unused pwrsts_mem_ret
  ARM: OMAP: DRA7: powerdomain data: Remove unused pwrsts_logic_ret
  ARM: OMAP: DRA7: powerdomain data: Set L3init and L4per to ON
  ARM: imx6ul: Fix Micrel PHY mask
  ARM: OMAP2+: Select OMAP_INTERCONNECT for SOC_AM43XX
  ARM: dts: DRA74x: fix DSS PLL2 addresses
  ARM: OMAP2: Enable Errata 430973 for OMAP3
  ARM: dts: socfpga: Add missing PHY phandle
  ARM: dts: exynos: Fix port nodes names for Exynos5420 Peach Pit board
  ARM: dts: exynos: Fix port nodes names for Exynos5250 Snow board
  ARM: dts: sun6i: yones-toptech-bs1078-v2: Drop constraints on dc1sw regulator
  ARM: dts: sun6i: primo81: Drop constraints on dc1sw regulator
  ARM: dts: sunxi: Add OLinuXino Lime2 eMMC to the Makefile
  ...

OMAP-GPMC: Fixes for for v4.7-rc cycle:

- Fix omap gpmc EXTRADELAY timing. The DT provided timings
were wrongly used causing devices requiring extra delay timing
to fail.

* tag 'gpmc-omap-fixes-for-v4.7' of https://github.com/rogerq/linux:
  memory: omap-gpmc: Fix omap gpmc EXTRADELAY timing
  + Linux 4.7-rc3
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v4.7/fixes-powedomain' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Fixes for omaps for v4.7-rc cycle:

- Fix dra7 for hardware issues limiting L4Per and L3init power domains
  to on state. Without this the devices may not work correctly after
  some time of use because of asymmetric aging. And related to this,
  let's also remove the unusable states.

- Always select omap interconnect for am43x as otherwise the am43x
  only configurations will not boot properly. This can happen easily
  for any product kernels that leave out other SoCs to save memory.

- Fix DSS PLL2 addresses that have gone unused for now

- Select erratum 430973 for omap3, this is now safe to do and can
  save quite a bit of debugging time for people who may have left
  it out.

* tag 'omap-for-v4.7/fixes-powedomain' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP: DRA7: powerdomain data: Remove unused pwrsts_mem_ret
  ARM: OMAP: DRA7: powerdomain data: Remove unused pwrsts_logic_ret
  ARM: OMAP: DRA7: powerdomain data: Set L3init and L4per to ON
  ARM: OMAP2+: Select OMAP_INTERCONNECT for SOC_AM43XX
  ARM: dts: DRA74x: fix DSS PLL2 addresses
  ARM: OMAP2: Enable Errata 430973 for OMAP3
  + Linux 4.7-rc2
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'fixes-rcu-fiq-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Fixes for omaps for v4.7-rc cycle:

- Two boot warning fixes from the RCU tree that should have gotten
  merged several weeks ago already but did not because of issues
  with who merges them. Paul has now split the RCU warning fixes into
  sets for various maintainers.

- Fix ams-delta FIQ regression caused by omap1 sparse IRQ changes

- Fix PM for omap3 boards using timer12 and gptimer, like the
  original beagleboard

- Fix hangs on am437x-sk-evm by lowering the I2C bus speed

* tag 'fixes-rcu-fiq-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: am437x-sk-evm: Reduce i2c0 bus speed for tps65218
  ARM: OMAP2+: timer: add probe for clocksources
  ARM: OMAP1: fix ams-delta FIQ handler to work with sparse IRQ
  arm: Use _rcuidle for smp_cross_call() tracepoints
  arm: Use _rcuidle tracepoint to allow use from idle
Signed-off-by: Olof Johansson <olof@lixom.net>

This patch fixes a non-booting issue in Mainline.

When booting with a compressed kernel, we need to be careful how we
populate memory close to DDR start.  AUTO_ZRELADDR is enabled by default
in multi-arch enabled configurations, which place some restrictions on
where the kernel is placed and where it will be uncompressed to on boot.

AUTO_ZRELADDR takes the decompressor code's start address and masks out
the bottom 28 bits to obtain an address to uncompress the kernel to
(thus a load address of 0x42000000 means that the kernel will be
uncompressed to 0x40000000 i.e. DDR START on this platform).

Even changing the load address to after the co-processor's shared memory
won't render a booting platform, since the AUTO_ZRELADDR algorithm still
ensures the kernel is uncompressed into memory shared with the first
co-processor (0x40000000).

Another option would be to move loading to 0x4A000000, since this will
mean the decompressor will decompress the kernel to 0x48000000. However,
this would mean a large chunk (0x44000000 => 0x48000000 (64MB)) of
memory would essentially be wasted for no good reason.

Until we can work with ST to find a suitable memory location to
relocate co-processor shared memory, let's disable the shared memory
nodes.  This will ensure a working platform in the mean time.

NB: The more observant of you will notice that we're leaving the DMU
shared memory node enabled; this is because a) it is the only one in
active use at the time of this writing and b) it is not affected by
the current default behaviour which is causing issues.

Fixes: fe135c63 (ARM: dts: STiH407: Move over to using the 'reserved-memory' API for obtaining DMA memory)
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'imx-fixes-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes

The i.MX fixes for 4.7:
 - Correct Micrel PHY mask to fix the issue that i.MX6UL ethernet works
   in U-Boot but not in kernel.

* tag 'imx-fixes-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: imx6ul: Fix Micrel PHY mask
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull ARM fixes from Russell King:
 "A couple of fixes for pmd_mknotpresent()/pmd_present() for LPAE
  systems"

* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: 8579/1: mm: Fix definition of pmd_mknotpresent
  ARM: 8578/1: mm: ensure pmd_present only checks the valid bit

Pull USB fixes from Greg KH:
 "Here are a bunch (65) of USB fixes for 4.7-rc4.  Sorry about the
  quantity, I've been slow in getting these out.

  The majority are the "normal" gadget, musb, and xhci fixes, that we
  all are used to.  There are also a few other tiny fixes resolving a
  number of reported issues that showed up in 4.7-rc1.

  All of these have been in linux-next"

* tag 'usb-4.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (65 commits)
  usbip: rate limit get_frame_number message
  usb: musb: sunxi: Remove bogus "Frees glue" comment
  usb: musb: sunxi: Fix NULL ptr deref when gadget is registered before musb
  usb: echi-hcd: Add ehci_setup check before echi_shutdown
  usb: host: ehci-msm: Conditionally call ehci suspend/resume
  MAINTAINERS: Add file patterns for usb device tree bindings
  usb: host: ehci-tegra: Avoid getting the same reset twice
  usb: host: ehci-tegra: Grab the correct UTMI pads reset
  USB: mos7720: delete parport
  USB: OHCI: Don't mark EDs as ED_OPER if scheduling fails
  phy: ti-pipe3: Program the DPLL even if it was already locked
  usb: musb: Stop bulk endpoint while queue is rotated
  usb: musb: Ensure rx reinit occurs for shared_fifo endpoints
  usb: musb: host: correct cppi dma channel for isoch transfer
  usb: musb: only restore devctl when session was set in backup
  usb: phy: Check initial state for twl6030
  usb: musb: Use normal module_init for 2430 glue
  usb: musb: Remove pm_runtime_set_irq_safe
  usb: musb: Remove extra PM runtime calls from 2430 glue layer
  usb: musb: Return error value from musb_mailbox
  ...

Pull IIO and staging fixes from Greg KH:
 "Here are a number of IIO and staging bugfixes for 4.7-rc4.

  Nothing huge, the normal amount of iio driver fixes, and some small
  staging driver bugfixes for some reported problems (2 are reverts of
  patches that went into 4.7-rc1).  All have been in linux-next with no
  reported issues"

* tag 'staging-4.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (24 commits)
  Revert "Staging: rtl8188eu: rtw_efuse: Use sizeof type *pointer instead of sizeof type."
  Revert "Staging: drivers: rtl8188eu: use sizeof(*ptr) instead of sizeof(struct)"
  staging: lustre: lnet: Don't access NULL NI on failure path
  iio: hudmidity: hdc100x: fix incorrect shifting and scaling
  iio: light apds9960: Add the missing dev.parent
  iio: Fix error handling in iio_trigger_attach_poll_func
  iio: st_sensors: Disable DRDY at init time
  iio: st_sensors: Init trigger before irq request
  iio: st_sensors: switch to a threaded interrupt
  iio: light: bh1780: assign a static name
  iio: bh1780: dereference the client properly
  iio: humidity: hdc100x: fix IIO_TEMP channel reporting
  iio:st_pressure: fix sampling gains (bring inline with ABI)
  iio: proximity: as3935: fix buffer stack trashing
  iio: proximity: as3935: remove triggered buffer processing
  iio: proximity: as3935: correct IIO_CHAN_INFO_RAW output
  max44000: Remove scale from proximity
  iio: humidity: am2315: Remove a stray unlock
  iio: humidity: hdc100x: correct humidity integration time mask
  iio: pressure: bmp280: fix error message for wrong chip id
  ...

Pull driver core fixes from Greg KH:
 "Here are a small number of debugfs, ISA, and one driver core fix for
  4.7-rc4.

  All of these resolve reported issues.  The ISA ones have spent the
  least amount of time in linux-next, sorry about that, I didn't realize
  they were regressions that needed to get in now (thanks to Thorsten
  for the prodding!) but they do all pass the 0-day bot tests.  The
  others have been in linux-next for a while now.

  Full details about them are in the shortlog below"

* tag 'driver-core-4.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  isa: Dummy isa_register_driver should return error code
  isa: Call isa_bus_init before dependent ISA bus drivers register
  watchdog: ebc-c384_wdt: Allow build for X86_64
  iio: stx104: Allow build for X86_64
  gpio: Allow PC/104 devices on X86_64
  isa: Allow ISA-style drivers on modern systems
  base: make module_create_drivers_dir race-free
  debugfs: open_proxy_open(): avoid double fops release
  debugfs: full_proxy_open(): free proxy on ->open() failure
  kernel/kcov: unproxify debugfs file's fops

Pull char/misc driver fixes from Greg KH:
 "Here are a small number of char and misc driver fixes for 4.7-rc4.

  They resolve some minor issues that have been reported, and have all
  been in linux-next"

* tag 'char-misc-4.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  coresight: Handle build path error
  coresight: Fix erroneous memset in tmc_read_unprepare_etr
  coresight: Fix tmc_read_unprepare_etr
  coresight: Fix NULL pointer dereference in _coresight_build_path
  extcon: palmas: Fix boot up state of VBUS when using GPIO detection
  mcb: Acquire reference to carrier module in core
  mcb: Acquire reference to device in probe
  mei: don't use wake_up_interruptible for wr_ctrl

Pull btrfs fixes from Chris Mason:
 "The most user visible change here is a fix for our recent superblock
  validation checks that were causing problems on non-4k pagesized
  systems"

* 'for-linus-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: btrfs_check_super_valid: Allow 4096 as stripesize
  btrfs: remove build fixup for qgroup_account_snapshot
  btrfs: use new error message helper in qgroup_account_snapshot
  btrfs: avoid blocking open_ctree from cleaner_kthread
  Btrfs: don't BUG_ON() in btrfs_orphan_add
  btrfs: account for non-CoW'd blocks in btrfs_abort_transaction
  Btrfs: check if extent buffer is aligned to sectorsize
  btrfs: Use correct format specifier

Pull ACPI fix from Rafael Wysocki:
 "Revert a recent ACPICA commit that introduced a suspend-to-RAM
  regression on one system due to incorrect information in its ACPI
  tables that had not been taken into consideration at all before (and
  everything worked), but the commit in question started to use it"

* tag 'acpi-4.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  Revert "ACPICA: ACPI 2.0, Hardware: Add access_width/bit_offset support for acpi_hw_write()"

Pull power management fixes from Rafael Wysocki:
 "Fixes for two recent regressions that may lead to degraded performance
  (operating performance points framework, intel_pstate).

  Specifics:

   - Fix a recent regression in the intel_pstate driver that may lead to
     degraded performance on some systems due to missing turbo state
     entry in the table returned by the ACPI _PSS object (Srinivas
     Pandruvada).

   - Fix a recent regression in the OPP (operating performance points)
     framework that may lead to degraded performance on some systems
     where the OPP table is created too early (Viresh Kumar)"

* tag 'pm-4.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  PM / OPP: Add 'UNKNOWN' status for shared_opp in struct opp_table
  cpufreq: intel_pstate: Adjust _PSS[0] freqeuency if needed

Pull HID subsystem fixes from Jiri Kosina:

 - kernel panic fix in hid-elo from Oliver Neukum

 - Surface Pro 3 device quirk from Benjamin Tissoires

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: multitouch: Add MT_QUIRK_NOT_SEEN_MEANS_UP to Surface Pro 3
  HID: elo: kill not flush the work

The inline isa_register_driver stub simply allows compilation on systems
with CONFIG_ISA disabled; the dummy isa_register_driver does not
register an isa_driver at all. The inline isa_register_driver should
return -ENODEV to indicate lack of support when attempting to register
an isa_driver on such a system with CONFIG_ISA disabled.

Cc: Matthew Wilcox <matthew@wil.cx>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Tested-by: Ye Xiaolong
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The isa_bus_init function must be called before drivers which utilize
the ISA bus driver are registered. A race condition for initilization
exists if device_initcall is used (the isa_bus_init callback is placed
in the same initcall level as dependent drivers which use module_init).
This patch ensures that isa_bus_init is called first by utilizing
postcore_initcall in favor of device_initcall.

Fixes: a5117ba7 ("[PATCH] Driver model: add ISA bus")
Cc: Rene Herman <rene.herman@keyaccess.nl>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

With the introduction of the ISA_BUS_API Kconfig option, ISA-style
drivers may be built for X86_64 architectures. This patch changes the
ISA Kconfig option dependency of the WinSystems EBC-C384 watchdog timer
driver to ISA_BUS_API, thus allowing it to build for X86_64 as it is
expected to.

Cc: Wim Van Sebroeck <wim@iguana.be>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

With the introduction of the ISA_BUS_API Kconfig option, ISA-style
drivers may be built for X86_64 architectures. This patch changes the
ISA Kconfig option dependency of the Apex Embedded Systems STX104 DAC
driver to ISA_BUS_API, thus allowing it to build for X86_64 as it is
expected to.

Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

With the introduction of the ISA_BUS_API Kconfig option, ISA-style
drivers may be built for X86_64 architectures. This patch changes the
ISA Kconfig option dependency of the PC/104 drivers to ISA_BUS_API, thus
allowing them to build for X86_64 as they are expected to.

Cc: Alexandre Courbot <gnurou@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Several modern devices, such as PC/104 cards, are expected to run on
modern systems via an ISA bus interface. Since ISA is a legacy interface
for most modern architectures, ISA support should remain disabled in
general. Support for ISA-style drivers should be enabled on a per driver
basis.

To allow ISA-style drivers on modern systems, this patch introduces the
ISA_BUS_API and ISA_BUS Kconfig options. The ISA bus driver will now
build conditionally on the ISA_BUS_API Kconfig option, which defaults to
the legacy ISA Kconfig option. The ISA_BUS Kconfig option allows the
ISA_BUS_API Kconfig option to be selected on architectures which do not
enable ISA (e.g. X86_64).

The ISA_BUS Kconfig option is currently only implemented for X86
architectures. Other architectures may have their own ISA_BUS Kconfig
options added as required.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It's annoying to constantly see the same "Not yet implemented" message
over and over with nothing able to be done about it, so rate limit it
for now to keep user's logs "clean".
Reported-by: Lars Täuber <lars.taeuber@web.de>
Tested-by: Lars Täuber <lars.taeuber@web.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

* acpica-fixes:
  Revert "ACPICA: ACPI 2.0, Hardware: Add access_width/bit_offset support for acpi_hw_write()"

* pm-opp:
  PM / OPP: Add 'UNKNOWN' status for shared_opp in struct opp_table

* pm-cpufreq-fixes:
  cpufreq: intel_pstate: Adjust _PSS[0] freqeuency if needed

This reverts commit b5e12ec3 ("Staging: rtl8188eu: rtw_efuse: Use
sizeof type *pointer instead of sizeof type.").

This commit is wrong, the rtw_malloc2d helper function takes the size of
the array elements as its 3th argument, whereas sizeof(*eFuseWord)
gives the size of a pointer instead of the size of a u16.

Since sizeof(void *) > sizeof(u16) this has no adverse effects, but it
is still wrong.

Cc: Sandhya Bankar <bankarsandhya512@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 99aded71 ("Staging: drivers: rtl8188eu: use
sizeof(*ptr) instead of sizeof(struct)").

This commit is wrong, as adapt->HalData has a type of "void *", so
now we are allocating a much to small struct, which causes the driver
to overwrite random memory which leads to a non working driver and
various system crashes.

Cc: Jacky Boen <aqiank@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull arm64 fixes from Will Deacon:
 "The main things are getting kgdb up and running with upstream GDB
  after a protocol change was reverted and fixing our spin_unlock_wait
  and spin_is_locked implementations after doing some similar work with
  PeterZ on the qspinlock code last week.  Whilst we haven't seen any
  failures in practice, it's still worth getting this fixed.

  Summary:

   - Plug the ongoing spin_unlock_wait/spin_is_locked mess
   - KGDB protocol fix to sync w/ GDB
   - Fix MIDR-based PMU probing for old 32-bit SMP systems
     (OMAP4/Realview)
   - Minor tweaks to the fault handling path"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: kgdb: Match pstate size with gdbserver protocol
  arm64: spinlock: Ensure forward-progress in spin_unlock_wait
  arm64: spinlock: fix spin_unlock_wait for LSE atomics
  arm64: spinlock: order spin_{is_locked,unlock_wait} against local locks
  arm: pmu: Fix non-devicetree probing
  arm64: mm: mark fault_info table const
  arm64: fix dump_instr when PAN and UAO are in use

Pull IOMMU fixes from Joerg Roedel:
 "Three patches queued up:

   - Fix for ARM-SMMU to add a missing iommu-ops callback which is
     required by common iommu code

   - Fix for the rockchip iommu where the wrong MMUs got the commands

   - A regression fix for the Intel VT-d driver.  The regression only
     showed up on X58 chipsets with more than one iommu.  These chipsets
     seem to require that QI is enabled on all IOMMUs before it can be
     used"

* tag 'iommu-fixes-v4.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/vt-d: Enable QI on all IOMMUs before setting root entry
  iommu/rockchip: Fix zap cache during device attach
  iommu/arm-smmu: Wire up map_sg for arm-smmu-v3

Pull LED fixes from Jacek Anaszewski:

 - Fix brightness setting upon hardware blinking enabled

 - Handle suspend/resume in heartbeat trigger

* tag 'for-4.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
  leds: handle suspend/resume in heartbeat trigger
  leds: core: Fix brightness setting upon hardware blinking enabled