- 15 Jan, 2015 10 commits
-
-
James Hogan authored
commit ac030860 upstream. The end timer is used for switching back from repeat code timings when no repeat codes have been received for a certain amount of time. When the protocol is changed, the end timer is deleted synchronously with del_timer_sync(), however this takes place while holding the main spin lock, and the timer handler also needs to acquire the spin lock. This opens the possibility of a deadlock on an SMP system if the protocol is changed just as the repeat timer is expiring. One CPU could end up in img_ir_set_decoder() holding the lock and waiting for the end timer to complete, while the other CPU is stuck in the timer handler spinning on the lock held by the first CPU. Lockdep also spots a possible lock inversion in the same code, since img_ir_set_decoder() acquires the img-ir lock before the timer lock, but the timer handler will try and acquire them the other way around: ========================================================= [ INFO: possible irq lock inversion dependency detected ] 3.18.0-rc5+ #957 Not tainted --------------------------------------------------------- swapper/0/0 just changed the state of lock: (((&hw->end_timer))){+.-...}, at: [<4006ae5c>] _call_timer_fn+0x0/0xfc but this lock was taken by another, HARDIRQ-safe lock in the past: (&(&priv->lock)->rlock#2){-.....} and interrupts could create inverse lock ordering between them. other info that might help us debug this: Possible interrupt unsafe locking scenario: CPU0 CPU1 ---- ---- lock(((&hw->end_timer))); local_irq_disable(); lock(&(&priv->lock)->rlock#2); lock(((&hw->end_timer))); <Interrupt> lock(&(&priv->lock)->rlock#2); *** DEADLOCK *** This is fixed by releasing the main spin lock while performing the del_timer_sync() call. The timer is prevented from restarting before the lock is reacquired by a new "stopping" flag which img_ir_handle_data() checks before updating the timer. --------------------------------------------------------- swapper/0/0 just changed the state of lock: (((&hw->end_timer))){+.-...}, at: [<4006ae5c>] _call_timer_fn+0x0/0xfc but this lock was taken by another, HARDIRQ-safe lock in the past: (&(&priv->lock)->rlock#2){-.....} and interrupts could create inverse lock ordering between them. other info that might help us debug this: Possible interrupt unsafe locking scenario: CPU0 CPU1 ---- ---- lock(((&hw->end_timer))); local_irq_disable(); lock(&(&priv->lock)->rlock#2); lock(((&hw->end_timer))); <Interrupt> lock(&(&priv->lock)->rlock#2); *** DEADLOCK *** This is fixed by releasing the main spin lock while performing the del_timer_sync() call. The timer is prevented from restarting before the lock is reacquired by a new "stopping" flag which img_ir_handle_data() checks before updating the timer. Signed-off-by:
James Hogan <james.hogan@imgtec.com> Cc: Sifan Naeem <sifan.naeem@imgtec.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Dylan Rajaratnam authored
commit ea0de4ec upstream. A problem was found on Polaris where if the unit it booted via the power button on the infrared remote then the next button press on the remote would return the key code used to power on the unit. The sequence is: - The polaris powered off but with the powerdown controller (PDC) block still powered. - Press power key on remote, IR block receives the key. - Kernel starts, IR code is in IMG_IR_DATA_x but neither IMG_IR_RXDVAL or IMG_IR_RXDVALD2 are set. - Wait any amount of time. - Press any key. - IMG_IR_RXDVAL or IMG_IR_RXDVALD2 is set but IMG_IR_DATA_x is unchanged since the powerup key data was never read. This is worked around by always reading the IMG_IR_DATA_x in img_ir_set_decoder(), rather than only when the IMG_IR_RXDVAL or IMG_IR_RXDVALD2 bit is set. Signed-off-by:
Dylan Rajaratnam <dylan.rajaratnam@imgtec.com> Signed-off-by:
-
Stefano Stabellini authored
commit 2c3fc8d2 upstream. Need to pass the pointer within the swiotlb internal buffer to the swiotlb library, that in the case of xen_unmap_single is dev_addr, not paddr. Signed-off-by:
Stefano Stabellini <stefano.stabellini@eu.citrix.com> Acked-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by:
-
Stefano Stabellini authored
commit 9490c6c6 upstream. In xen_swiotlb_sync_single we always call xen_dma_sync_single_for_cpu, even when we should call xen_dma_sync_single_for_device. Fix that. Signed-off-by:
-
Stefano Stabellini authored
commit c884227e upstream. On x86 truncation cannot occur because config XEN depends on X86_64 || (X86_32 && X86_PAE). On ARM truncation can occur without CONFIG_ARM_LPAE, when the dma operation involves foreign grants. However in that case the physical address returned by xen_bus_to_phys is actually invalid (there is no mfn to pfn tracking for foreign grants on ARM) and it is not used. Signed-off-by:
Catalin Marinas <catalin.marinas@arm.com> Acked-by:
-
Stefano Stabellini authored
commit d6883e6f upstream. xen_dma_unmap_page and xen_dma_sync_single_for_cpu take a dma_addr_t handle as argument, not a physical address. Signed-off-by:
-
Alex Deucher authored
commit 5e5c21ca upstream. Check the that ring we are using for copies is functional rather than the GFX ring. On newer asics we use the DMA ring for bo moves. Reviewed-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Dominique Leuenberger authored
commit 6583659e upstream. HP ZBook 15 laptop needs a non-standard mapping (x_inverted). BugLink: http://bugzilla.opensuse.org/show_bug.cgi?id=905329Signed-off-by:
Dominique Leuenberger <dimstar@opensuse.org> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Darren Hart <dvhart@linux.intel.com> Signed-off-by:
-
Thomas Hellstrom authored
commit 89669e7a upstream. The commit "vmwgfx: Rework fence event action" introduced a number of bugs that are fixed with this commit: a) A forgotten return stateemnt. b) An if statement with identical branches. Reported-by:
Rob Clark <robdclark@gmail.com> Signed-off-by:
Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by:
Jakob Bornecrantz <jakob@vmware.com> Reviewed-by:
Sinclair Yeh <syeh@vmware.com> Signed-off-by:
-
Thomas Hellstrom authored
commit e338c4c2 upstream. The function vmw_master_check() might return -ERESTARTSYS if there is a signal pending, indicating that the IOCTL should be rerun, potentially from user-space. At that point we shouldn't print out an error message since that is not an error condition. In short, avoid bloating the kernel log when a process refuses to die on SIGTERM. Signed-off-by:
-
- 12 Jan, 2015 30 commits
-
-
Chris Wilson authored
commit 2b387059 upstream. In all likelihood we will do a few hundred errnoneous register operations if we do a single invalid register access whilst the device is suspended. As each instance causes a WARN, this floods the system logs and can make the system unresponsive. The warning was first introduced in commit b2ec142c Author: Paulo Zanoni <paulo.r.zanoni@intel.com> Date: Fri Feb 21 13:52:25 2014 -0300 drm/i915: call assert_device_not_suspended at gen6_force_wake_work and despite the claims the WARN is still encountered in the wild today. Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Cc: Imre Deak <imre.deak@intel.com> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
-
NeilBrown authored
commit 108cef3a upstream. It is critical that fetch_block() and handle_stripe_dirtying() are consistent in their analysis of what needs to be loaded. Otherwise raid5 can wait forever for a block that won't be loaded. Currently when writing to a RAID5 that is resyncing, to a location beyond the resync offset, handle_stripe_dirtying chooses a reconstruct-write cycle, but fetch_block() assumes a read-modify-write, and a lockup can happen. So treat that case just like RAID6, just as we do in handle_stripe_dirtying. RAID6 always does reconstruct-write. This bug was introduced when the behaviour of handle_stripe_dirtying was changed in 3.7, so the patch is suitable for any kernel since, though it will need careful merging for some versions. Fixes: a7854487Reported-by:
Henry Cai <henryplusplus@gmail.com> Signed-off-by:
NeilBrown <neilb@suse.de> Signed-off-by:
-
Eric W. Biederman authored
commit b2f5d4dc upstream. Forced unmount affects not just the mount namespace but the underlying superblock as well. Restrict forced unmount to the global root user for now. Otherwise it becomes possible a user in a less privileged mount namespace to force the shutdown of a superblock of a filesystem in a more privileged mount namespace, allowing a DOS attack on root. Signed-off-by:
"Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by:
-
Eric W. Biederman authored
commit 4a44a19b upstream. - MNT_NODEV should be irrelevant except when reading back mount flags, no longer specify MNT_NODEV on remount. - Test MNT_NODEV on devpts where it is meaningful even for unprivileged mounts. - Add a test to verify that remount of a prexisting mount with the same flags is allowed and does not change those flags. - Cleanup up the definitions of MS_REC, MS_RELATIME, MS_STRICTATIME that are used when the code is built in an environment without them. - Correct the test error messages when tests fail. There were not 5 tests that tested MS_RELATIME. Signed-off-by:
-
Eric W. Biederman authored
commit 3e186641 upstream. Now that remount is properly enforcing the rule that you can't remove nodev at least sandstorm.io is breaking when performing a remount. It turns out that there is an easy intuitive solution implicitly add nodev on remount when nodev was implicitly added on mount. Tested-by:
Cedric Bosdonnat <cbosdonnat@suse.com> Tested-by:
Richard Weinberger <richard@nod.at> Signed-off-by:
-
Milan Broz authored
commit 1a71d6ff upstream. Use memzero_explicit to cleanup sensitive data allocated on stack to prevent the compiler from optimizing and removing memset() calls. Signed-off-by:
Milan Broz <gmazyland@gmail.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Jiang Liu authored
commit cc4f14aa upstream. There's an off-by-one bug in function __domain_mapping(), which may trigger the BUG_ON(nr_pages < lvl_pages) when (nr_pages + 1) & superpage_mask == 0 The issue was introduced by commit 9051aa02 "intel-iommu: Combine domain_pfn_mapping() and domain_sg_mapping()", which sets sg_res to "nr_pages + 1" to avoid some of the 'sg_res==0' code paths. It's safe to remove extra "+1" because sg_res is only used to calculate page size now. Reported-And-Tested-by:
Sudeep Dutt <sudeep.dutt@intel.com> Signed-off-by:
Jiang Liu <jiang.liu@linux.intel.com> Acked-By:
David Woodhouse <David.Woodhouse@intel.com> Signed-off-by:
Joerg Roedel <jroedel@suse.de> [ luis: backported to 3.16: adjusted context ] Signed-off-by:
-
Emmanuel Grumbach authored
commit b4c82adc upstream. Interoperability issues were identified and root caused to the Smart Fifo watermarks. These issues arose with NetGear R7000. Fix this. Fixes: 1f3b0ff8 ("iwlwifi: mvm: Add Smart FIFO support") Reviewed-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
-
Emmanuel Grumbach authored
commit 5a12a07e upstream. Since the commit below, iwldvm sends the FLUSH command to the firmware. All the devices that use iwldvm have a firmware that expects the _v3 version of this command, besides 5150. 5150's latest available firmware still expects a _v2 version of the FLUSH command. This means that since the commit below, we had a mismatch for this specific device only. This mismatch led to the NMI below: Loaded firmware version: 8.24.2.2 Start IWL Error Log Dump: Status: 0x0000004C, count: 5 0x00000004 | NMI_INTERRUPT_WDG 0x000006F4 | uPc 0x000005BA | branchlink1 0x000006F8 | branchlink2 0x000008C2 | interruptlink1 0x00005B02 | interruptlink2 0x00000002 | data1 0x07030000 | data2 0x00000068 | line 0x3E80510C | beacon time 0x728A0EF4 | tsf low 0x0000002A | tsf hi 0x00000000 | time gp1 0x01BDC977 | time gp2 0x00000000 | time gp3 0x00010818 | uCode version 0x00000000 | hw version 0x00484704 | board version 0x00000002 | hcmd 0x2FF23080 | isr0 0x0103E000 | isr1 0x0000001A | isr2 0x1443FCC3 | isr3 0x11800112 | isr4 0x00000068 | isr_pref 0x000000D4 | wait_event 0x00000000 | l2p_control 0x00000007 | l2p_duration 0x00103040 | l2p_mhvalid 0x00000007 | l2p_addr_match 0x00000000 | lmpm_pmg_sel 0x00000000 | timestamp 0x00000200 | flow_handler This was reported here: https://bugzilla.kernel.org/show_bug.cgi?id=88961 Fixes: a0855054 ("iwlwifi: dvm: drop non VO frames when flushing") Signed-off-by:
-
Felix Fietkau authored
commit 9e4982f6 upstream. Like with ath9k, ath5k queues also need to be ordered by priority. queue_info->tqi_subtype already contains the correct index, so use it instead of relying on the order of ath5k_hw_setup_tx_queue calls. Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
-
Felix Fietkau authored
commit 78063d81 upstream. Hardware queues are ordered by priority. Use queue index 0 for BK, which has lower priority than BE. Signed-off-by:
-
Felix Fietkau authored
commit ad8fdccf upstream. The driver passes the desired hardware queue index for a WMM data queue in qinfo->tqi_subtype. This was ignored in ath9k_hw_setuptxqueue, which instead relied on the order in which the function is called. Reported-by:
Hubert Feurstein <h.feurstein@gmail.com> Signed-off-by:
-
Darrick J. Wong authored
commit 445559cd upstream. When dm-bufio sets out to use the bio built into a struct dm_buffer to issue an IO, it needs to call bio_reset after it's done with the bio so that we can free things attached to the bio such as the integrity payload. Therefore, inject our own endio callback to take care of the bio_reset after calling submit_io's end_io callback. Test case: 1. modprobe scsi_debug delay=0 dif=1 dix=199 ato=1 dev_size_mb=300 2. Set up a dm-bufio client, e.g. dm-verity, on the scsi_debug device 3. Repeatedly read metadata and watch kmalloc-192 leak! Signed-off-by:
Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
-
Joe Thornber authored
commit 1e32134a upstream. If the incoming bio is a WRITE and completely covers a block then we don't bother to do any copying for a promotion operation. Once this is done the cache block and origin block will be different, so we need to set it to 'dirty'. Signed-off-by:
Joe Thornber <ejt@redhat.com> Signed-off-by:
-
Joe Thornber authored
commit f29a3147 upstream. Overwrite causes the cache block and origin blocks to diverge, which is only allowed in writeback mode. Signed-off-by:
-
Christian Riesch authored
commit 8bfbe2de upstream. Commit 19e2ad6a ("n_tty: Remove overflow tests from receive_buf() path") moved the increment of read_head into the arguments list of read_buf_addr(). Function calls represent a sequence point in C. Therefore read_head is incremented before the character c is placed in the buffer. Since the circular read buffer is a lock-less design since commit 6d76bd26 ("n_tty: Make N_TTY ldisc receive path lockless"), this creates a race condition that leads to communication errors. This patch modifies the code to increment read_head _after_ the data is placed in the buffer and thus fixes the race for non-SMP machines. To fix the problem for SMP machines, memory barriers must be added in a separate patch. Signed-off-by:
Christian Riesch <christian.riesch@omicron.at> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Dmitry Tunin authored
commit 3bb30a7c upstream. Add support for Bluetooth MCI WB335 (AR9565) Wi-Fi+bt module. This Bluetooth module requires loading patch and sysconfig by ath3k driver. T: Bus=01 Lev=02 Prnt=03 Port=00 Cnt=01 Dev#= 20 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3408 Rev= 0.02 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by:
Dmitry Tunin <hanipouspilot@gmail.com> Signed-off-by:
Johan Hedberg <johan.hedberg@intel.com> Signed-off-by:
-
James Hogan authored
commit 66dfd101 upstream. Commit f1d2736c (mmc: dw_mmc: control card read threshold) added dw_mci_ctrl_rd_thld() with an unconditional write to the CDTHRCTL register at offset 0x100. However before version 240a, the FIFO region started at 0x100, so the write messes with the FIFO and completely breaks the driver. If the version id < 240A, return early from dw_mci_ctl_rd_thld() so as not to hit this problem. Fixes: f1d2736c (mmc: dw_mmc: control card read threshold) Signed-off-by:
Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Robert Baldyga authored
commit 1ff383a4 upstream. This patch adds waiting until transmit buffer and shifter will be empty before clock disabling. Without this fix it's possible to have clock disabled while data was not transmited yet, which causes unproper state of TX line and problems in following data transfers. Signed-off-by:
Robert Baldyga <r.baldyga@samsung.com> Signed-off-by:
-
Axel Lin authored
commit 6b1f40cf upstream. The mcb_device_id table is supposed to be zero-terminated. Signed-off-by:
Axel Lin <axel.lin@ingics.com> Signed-off-by:
-
Dmitry Eremin-Solenikov authored
commit 1a5fb99d upstream. Some boards with TC6393XB chip require full state restore during system resume thanks to chip's VCC being cut off during suspend (Sharp SL-6000 tosa is one of them). Failing to do so would result in ohci Oops on resume due to internal memory contentes being changed. Fail ohci suspend on tc6393xb is full state restore is required. Recommended workaround is to unbind tmio-ohci driver before suspend and rebind it after resume. Signed-off-by:
Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Signed-off-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
-
Tony Lindgren authored
commit 1b9b46d0 upstream. Commit e7cd1d1e ("mfd: twl4030-power: Add generic reset configuration") accidentally removed the compatible flag for "ti,twl4030-power" that should be there as documented in the binding. If "ti,twl4030-power" only the poweroff configuration is done by the driver. Fixes: e7cd1d1e ("mfd: twl4030-power: Add generic reset configuration") Reported-by:
"Dr. H. Nikolaus Schaller" <hns@goldelico.com> Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Jean-Baptiste Maneyrol authored
commit 6296f4a8 upstream. Current driver uses a common buffer for reading reports either synchronously in i2c_hid_get_raw_report() and asynchronously in the interrupt handler. There is race condition if an interrupt arrives immediately after the report is received in i2c_hid_get_raw_report(); the common buffer is modified by the interrupt handler with the new report and then i2c_hid_get_raw_report() proceed using wrong data. Fix it by using a separate buffers for synchronous reports. Signed-off-by:
Jean-Baptiste Maneyrol <jmaneyrol@invensense.com> [Antonio Borneo: cleanup, rebase to v3.17, submit mainline] Signed-off-by:
Antonio Borneo <borneo.antonio@gmail.com> Reviewed-by:
Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Takashi Iwai authored
commit 2228d80d upstream. We've got a bug report at disconnecting a Webcam, where the kernel spews warnings like below: WARNING: CPU: 0 PID: 8385 at ../fs/sysfs/group.c:219 sysfs_remove_group+0x87/0x90() sysfs group c0b2350c not found for kobject 'event3' CPU: 0 PID: 8385 Comm: queue2:src Not tainted 3.16.2-1.gdcee397-default #1 Hardware name: ASUSTeK Computer INC. A7N8X-E/A7N8X-E, BIOS ASUS A7N8X-E Deluxe ACPI BIOS Rev 1013 11/12/2004 c08d0705 ddc75cbc c0718c5b ddc75ccc c024b654 c08c6d44 ddc75ce8 000020c1 c08d0705 000000db c03d1ec7 c03d1ec7 00000009 00000000 c0b2350c d62c9064 ddc75cd4 c024b6a3 00000009 ddc75ccc c08c6d44 ddc75ce8 ddc75cfc c03d1ec7 Call Trace: [<c0205ba6>] try_stack_unwind+0x156/0x170 [<c02046f3>] dump_trace+0x53/0x180 [<c0205c06>] show_trace_log_lvl+0x46/0x50 [<c0204871>] show_stack_log_lvl+0x51/0xe0 [<c0205c67>] show_stack+0x27/0x50 [<c0718c5b>] dump_stack+0x3e/0x4e [<c024b654>] warn_slowpath_common+0x84/0xa0 [<c024b6a3>] warn_slowpath_fmt+0x33/0x40 [<c03d1ec7>] sysfs_remove_group+0x87/0x90 [<c05a2c54>] device_del+0x34/0x180 [<c05e3989>] evdev_disconnect+0x19/0x50 [<c05e06fa>] __input_unregister_device+0x9a/0x140 [<c05e0845>] input_unregister_device+0x45/0x80 [<f854b1d6>] uvc_delete+0x26/0x110 [uvcvideo] [<f84d66f8>] v4l2_device_release+0x98/0xc0 [videodev] [<c05a25bb>] device_release+0x2b/0x90 [<c04ad8bf>] kobject_cleanup+0x6f/0x1a0 [<f84d5453>] v4l2_release+0x43/0x70 [videodev] [<c0372f31>] __fput+0xb1/0x1b0 [<c02650c1>] task_work_run+0x91/0xb0 [<c024d845>] do_exit+0x265/0x910 [<c024df64>] do_group_exit+0x34/0xa0 [<c025a76f>] get_signal_to_deliver+0x17f/0x590 [<c0201b6a>] do_signal+0x3a/0x960 [<c02024f7>] do_notify_resume+0x67/0x90 [<c071ebb5>] work_notifysig+0x30/0x3b [<b7739e60>] 0xb7739e5f ---[ end trace b1e56095a485b631 ]--- The cause is that uvc_status_cleanup() is called after usb_put_*() in uvc_delete(). usb_put_*() removes the sysfs parent and eventually removes the children recursively, so the later device_del() can't find its sysfs. The fix is simply rearrange the call orders in uvc_delete() so that the child is removed before the parent. Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=897736Reported-and-tested-by:
Martin Pluskal <mpluskal@suse.com> Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Greg Kroah-Hartman authored
commit 403dff4e upstream. We need to check that we have both a valid data and control inteface for both types of headers (union and not union.) References: https://bugzilla.kernel.org/show_bug.cgi?id=83551Reported-by:
Simon Schubert <2+kernel@0x2c.org> Signed-off-by:
-
Oliver Neukum authored
commit d908f847 upstream. If probe() fails not only the attributes need to be removed but also the memory freed. Reported-by:
Ahmed Tamrawi <ahmedtamrawi@gmail.com> Signed-off-by:
Oliver Neukum <oneukum@suse.de> Signed-off-by:
-
Peng Tao authored
commit 4bd5a980 upstream. nfs4_layoutget_release() drops layout hdr refcnt. Grab the refcnt early so that it is safe to call .release in case nfs4_alloc_pages fails. Signed-off-by:
Peng Tao <tao.peng@primarydata.com> Fixes: a47970ff ("NFSv4.1: Hold reference to layout hdr in layoutget") Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by:
-
Jens Axboe authored
commit a33c1ba2 upstream. We currently use num_possible_cpus(), but that breaks on sparc64 where the CPU ID space is discontig. Use nr_cpu_ids as the highest CPU ID instead, so we don't end up reading from invalid memory. Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Jarkko Nikula authored
commit 48826ee5 upstream. Commit 5fe5b767 ("ASoC: dapm: Do not pretend to support controls for non mixer/mux widgets") revealed ill-defined control in a route between "STENL Mux" and DACs in max98090.c: max98090 i2c-193C9890:00: Control not supported for path STENL Mux -> [NULL] -> DACL max98090 i2c-193C9890:00: ASoC: no dapm match for STENL Mux --> NULL --> DACL max98090 i2c-193C9890:00: ASoC: Failed to add route STENL Mux -> NULL -> DACL max98090 i2c-193C9890:00: Control not supported for path STENL Mux -> [NULL] -> DACR max98090 i2c-193C9890:00: ASoC: no dapm match for STENL Mux --> NULL --> DACR max98090 i2c-193C9890:00: ASoC: Failed to add route STENL Mux -> NULL -> DACR Since there is no control between "STENL Mux" and DACs the control name must be NULL not "NULL". Signed-off-by:
Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Sumit.Saxena@avagotech.com authored
commit 170c2387 upstream. Corrected wait_event() call which was waiting for wrong completion status (0xFF). Signed-off-by:
Sumit Saxena <sumit.saxena@avagotech.com> Signed-off-by:
Kashyap Desai <kashyap.desai@avagotech.com> Reviewed-by:
Tomas Henzl <thenzl@redhat.com> Signed-off-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
-
