Currently when a root PHY is deformed from a asd_sas_port we try to
release the slots in the LLDD, and fail.

Regardless, it is not right to release this early.

This patch removes the deformed function. As it was before, port
deformation is still done in hisi_sas_phy_down().

It would be nice to actually remove the hisi_sas_port_{de}formed() pair,
however we cannot as we need to know the asd_sas_port index libsas has
associated with an asd_sas_phy.

The hw does actually generate a port id for a PHY, but this seems to a
random number, so ignored for this purpose.

This patch also changes the code to link slots to the hisi_sas_device,
and not hisi_sas_port.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Add softreset to clear IO after internal abort device for SATA disk.

The SATA error handling for the controller is based on device internal
abort and softreset function.

The controller does not support internal abort for single IO, so we need
to execute internal abort for device.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Relocate the PHY init code from LLDD hw init path to
hisi_sas_scan_start().
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

There are some scenarios that we need to warm-reset to reset registers
of SAS controller. During reset we disable interrupts/DQs/PHYs, and
after reset we re-init the hardware and rescan the topology to see if
anything changed.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Introduce function to get hisi_sas_port from asd_sas_port.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

This is a bug introduced when they moved the fip subcodes to central
place. Was sending FIP_SC_VL_NOTE in fip.fip_subcode for VLAN request in
fnic_fcoe_send_vlan_req. Change is to use FIP_SC_VL_REQ instead.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The IO and Abort latency counter counts the time taken to complete the
IO and abort command into broad buckets. This is not intended for
performance measurement, just a debug statistic.  current_max_io_time
tries to keep track of the maximum time an IO has taken to complete if
it is > 30sec.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Just a simple counter of number of check conditions encountered on that
host.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

If SCSI-ML has already issued abort on a command i.e
FNIC_IOREQ_ABTS_PENDING is set and we get a IO completion, avoid this
being flagged as out-of-order completion by setting the FNIC_IO_DONE
flag in fnic_fcpio_icmnd_cmpl_handler
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Fixing the IO stats update (Active IOs and IO completion) to prevent
"Number of Active IOs" from becoming negative in the fnistats output.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Getting rid of else case to make the flow look bit simpler.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

This is to avoid the log from being filled with vlan discovery messages
when there is no vlan configured on the switch.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Not a full cleanup for the IRQ code, for that we'd need to know if the
max number of the various CQ types is going to stay 1 forever.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Buffer is a pointer to the static char array event_buffer and therefore
can never be null, so the check is redundant. Remove it.

Detected by CoverityScan, CID#1077556 ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Bradley Grove <bgrove@attotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Even if bus is not hot-pluggable, devices can be unbound from the driver
via sysfs, so we should not be using __exit annotations on remove()
methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

1. Add reboot notifier and register it in stex_probe for all supported
   device.

2. For all supported device in restart flow, we get a callback from
   notifier and set S6flag for stex_shutdown & stex_hba_stop to send
   restart command to FW.
Signed-off-by: Charles.Chiou <charles.chiou@tw.promise.com>
Signed-off-by: Paul.Lyu <paul.lyu@tw.promise.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Pegasus series is a RAID support product using Thunderbolt technology.
The newest product, Pegasus 3(P3) supports Thunderbolt 3 technology with
a different chip.

1. Change driver version.

2. Add P3 VID, DID and define it's device address.

3. P3 use msi interrupt, so stex_request_irq P3 type enable msi.

4. For hibernation, use msi_lock in stex_ss_handshake to prevent msi
   register write again when handshaking.

5. P3 doesn't need read() as flush.

6. In stex_ss_intr & stex_abort, P3 only clear interrupt register when
   getting vendor defined interrupt.
Signed-off-by: Charles.Chiou <charles.chiou@tw.promise.com>
Signed-off-by: Paul.Lyu <paul.lyu@tw.promise.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

refcount_t type and corresponding API should be used instead of atomic_t
when the variable is used as a reference counter. This allows to avoid
accidental refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Acked-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

refcount_t type and corresponding API should be used instead of atomic_t
when the variable is used as a reference counter. This allows to avoid
accidental refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Pull some more powerpc fixes from Michael Ellerman:
 "The main item is the addition of the Power9 Machine Check handler.
  This was delayed to make sure some details were correct, and is as
  minimal as possible.

  The rest is small fixes, two for the Power9 PMU, two dealing with
  obscure toolchain problems, two for the PowerNV IOMMU code (used by
  VFIO), and one to fix a crash on 32-bit machines with macio devices
  due to missing dma_ops.

  Thanks to:
    Alexey Kardashevskiy, Cyril Bur, Larry Finger, Madhavan Srinivasan,
    Nicholas Piggin"

* tag 'powerpc-4.11-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/64s: POWER9 machine check handler
  powerpc/64s: allow machine check handler to set severity and initiator
  powerpc/64s: fix handling of non-synchronous machine checks
  powerpc/pmac: Fix crash in dma-mapping.h with NULL dma_ops
  powerpc/powernv/ioda2: Update iommu table base on ownership change
  powerpc/powernv/ioda2: Gracefully fail if too many TCE levels requested
  selftests/powerpc: Replace stxvx and lxvx with stxvd2x/lxvd2x
  powerpc/perf: Handle sdar_mode for marked event in power9
  powerpc/perf: Fix perf_get_data_addr() for power9 DD1
  powerpc/boot: Fix zImage TOC alignment

Pull x86 platform driver updates from Darren Hart:
 "Asus fixes for the airplane LED and a long awaited fujitsu cleanup.

  asus-wmi:
   - Remove quirk_no_rfkill
   - Detect quirk_no_rfkill from the DSDT

  fujitsu-laptop:
   - remove redundant MODULE_ALIAS entries
   - autodetect LCD interface on all models
   - simplify acpi_bus_register_driver() error handling
   - remove redundant forward declarations
   - replace numeric values with constants
   - rename FUNC_RFKILL to FUNC_FLAGS
   - make platform-related variables match naming convention
   - replace "hotkey" with "laptop" in symbol names
   - clearly denote backlight-related symbols"

* tag 'platform-drivers-x86-v4.11-2' of git://git.infradead.org/linux-platform-drivers-x86:
  platform/x86: asus-wmi: Remove quirk_no_rfkill
  platform/x86: asus-wmi: Detect quirk_no_rfkill from the DSDT
  platform/x86: fujitsu-laptop: remove redundant MODULE_ALIAS entries
  platform/x86: fujitsu-laptop: autodetect LCD interface on all models
  platform/x86: fujitsu-laptop: simplify acpi_bus_register_driver() error handling
  platform/x86: fujitsu-laptop: remove redundant forward declarations
  platform/x86: fujitsu-laptop: replace numeric values with constants
  platform/x86: fujitsu-laptop: rename FUNC_RFKILL to FUNC_FLAGS
  platform/x86: fujitsu-laptop: make platform-related variables match naming convention
  platform/x86: fujitsu-laptop: replace "hotkey" with "laptop" in symbol names
  platform/x86: fujitsu-laptop: clearly denote backlight-related symbols

gup_p4d_range() should call gup_pud_range(), not itself.

[ This was not noticed on x86: this is the HAVE_GENERIC_RCU_GUP code
  used by arm[64] and powerpc    - Linus ]

Fixes: c2febafc ("mm: convert generic code to 5-level paging")
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reported-by: Anton Blanchard <anton@samba.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

With the detection introduced in the previous patches, we don't need
these static DMI-based quirks anymore.

This reverts the following commits:
56a37a72 "asus-wmi: Add quirk_no_rfkill_wapf4 for the Asus X456UA"
a961a285 "asus-wmi: Add quirk_no_rfkill_wapf4 for the Asus X456UF"
6b7ff2af "asus-wmi: Add quirk_no_rfkill for the Asus Z550MA"
02db9ff7 "asus-wmi: Add quirk_no_rfkill for the Asus U303LB"
2d735244 "asus-wmi: Add quirk_no_rfkill for the Asus N552VW"
a977e59c "asus-wmi: Create quirk for airplane_mode LED"
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[dvhart: minor commit message corrections]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>

Pull s390 fixes from Martin Schwidefsky:

 - four patches to get the new cputime code in shape for s390

 - add the new statx system call

 - a few bug fixes

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390: wire up statx system call
  KVM: s390: Fix guest migration for huge guests resulting in panic
  s390/ipl: always use load normal for CCW-type re-IPL
  s390/timex: micro optimization for tod_to_ns
  s390/cputime: provide archicture specific cputime_to_nsecs
  s390/cputime: reset all accounting fields on fork
  s390/cputime: remove last traces of cputime_t
  s390: fix in-kernel program checks
  s390/crypt: fix missing unlock in ctr_paes_crypt on error path

Pull x86 fixes from Thomas Gleixner:

 - a fix for the kexec/purgatory regression which was introduced in the
   merge window via an innocent sparse fix. We could have reverted that
   commit, but on deeper inspection it turned out that the whole
   machinery is neither documented nor robust. So a proper cleanup was
   done instead

 - the fix for the TLB flush issue which was discovered recently

 - a simple typo fix for a reboot quirk

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/tlb: Fix tlb flushing when lguest clears PGE
  kexec, x86/purgatory: Unbreak it and clean it up
  x86/reboot/quirks: Fix typo in ASUS EeeBook X205TA reboot quirk

Pull irq fixes from Thomas Gleixner:

 - a workaround for a GIC erratum

 - a missing stub function for CONFIG_IRQDOMAIN=n

 - fixes for a couple of type inconsistencies

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/crossbar: Fix incorrect type of register size
  irqchip/gicv3-its: Add workaround for QDF2400 ITS erratum 0065
  irqdomain: Add empty irq_domain_check_msi_remap
  irqchip/crossbar: Fix incorrect type of local variables

Fengguang reported random corruptions from various locations on x86-32
after commits d2852a22 ("arch: add ARCH_HAS_SET_MEMORY config") and
9d876e79 ("bpf: fix unlocking of jited image when module ronx not set")
that uses the former. While x86-32 doesn't have a JIT like x86_64, the
bpf_prog_lock_ro() and bpf_prog_unlock_ro() got enabled due to
ARCH_HAS_SET_MEMORY, whereas Fengguang's test kernel doesn't have module
support built in and therefore never had the DEBUG_SET_MODULE_RONX setting
enabled.

After investigating the crashes further, it turned out that using
set_memory_ro() and set_memory_rw() didn't have the desired effect, for
example, setting the pages as read-only on x86-32 would still let
probe_kernel_write() succeed without error. This behavior would manifest
itself in situations where the vmalloc'ed buffer was accessed prior to
set_memory_*() such as in case of bpf_prog_alloc(). In cases where it
wasn't, the page attribute changes seemed to have taken effect, leading to
the conclusion that a TLB invalidate didn't happen. Moreover, it turned out
that this issue reproduced with qemu in "-cpu kvm64" mode, but not for
"-cpu host". When the issue occurs, change_page_attr_set_clr() did trigger
a TLB flush as expected via __flush_tlb_all() through cpa_flush_range(),
though.

There are 3 variants for issuing a TLB flush: invpcid_flush_all() (depends
on CPU feature bits X86_FEATURE_INVPCID, X86_FEATURE_PGE), cr4 based flush
(depends on X86_FEATURE_PGE), and cr3 based flush.  For "-cpu host" case in
my setup, the flush used invpcid_flush_all() variant, whereas for "-cpu
kvm64", the flush was cr4 based. Switching the kvm64 case to cr3 manually
worked fine, and further investigating the cr4 one turned out that
X86_CR4_PGE bit was not set in cr4 register, meaning the
__native_flush_tlb_global_irq_disabled() wrote cr4 twice with the same
value instead of clearing X86_CR4_PGE in the first write to trigger the
flush.

It turned out that X86_CR4_PGE was cleared from cr4 during init from
lguest_arch_host_init() via adjust_pge(). The X86_FEATURE_PGE bit is also
cleared from there due to concerns of using PGE in guest kernel that can
lead to hard to trace bugs (see bff672e6 ("lguest: documentation V:
Host") in init()). The CPU feature bits are cleared in dynamic
boot_cpu_data, but they never propagated to __flush_tlb_all() as it uses
static_cpu_has() instead of boot_cpu_has() for testing which variant of TLB
flushing to use, meaning they still used the old setting of the host
kernel.

Clearing via setup_clear_cpu_cap(X86_FEATURE_PGE) so this would propagate
to static_cpu_has() checks is too late at this point as sections have been
patched already, so for now, it seems reasonable to switch back to
boot_cpu_has(X86_FEATURE_PGE) as it was prior to commit c109bf95
("x86/cpufeature: Remove cpu_has_pge"). This lets the TLB flush trigger via
cr3 as originally intended, properly makes the new page attributes visible
and thus fixes the crashes seen by Fengguang.

Fixes: c109bf95 ("x86/cpufeature: Remove cpu_has_pge")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: bp@suse.de
Cc: Kees Cook <keescook@chromium.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: lkp@01.org
Cc: Laura Abbott <labbott@redhat.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernrl.org/r/20170301125426.l4nf65rx4wahohyl@wfg-t540p.sh.intel.com
Link: http://lkml.kernel.org/r/25c41ad9eca164be4db9ad84f768965b7eb19d9e.1489191673.git.daniel@iogearbox.netSigned-off-by: Thomas Gleixner <tglx@linutronix.de>

Pull KVM fixes from Radim Krčmář:
 "ARM updates from Marc Zyngier:
   - vgic updates:
     - Honour disabling the ITS
     - Don't deadlock when deactivating own interrupts via MMIO
     - Correctly expose the lact of IRQ/FIQ bypass on GICv3

   - I/O virtualization:
     - Make KVM_CAP_NR_MEMSLOTS big enough for large guests with many
       PCIe devices

   - General bug fixes:
     - Gracefully handle exception generated with syndroms that the host
       doesn't understand
     - Properly invalidate TLBs on VHE systems

  x86:
   - improvements in emulation of VMCLEAR, VMX MSR bitmaps, and VCPU
     reset

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: nVMX: do not warn when MSR bitmap address is not backed
  KVM: arm64: Increase number of user memslots to 512
  KVM: arm/arm64: Remove KVM_PRIVATE_MEM_SLOTS definition that are unused
  KVM: arm/arm64: Enable KVM_CAP_NR_MEMSLOTS on arm/arm64
  KVM: Add documentation for KVM_CAP_NR_MEMSLOTS
  KVM: arm/arm64: VGIC: Fix command handling while ITS being disabled
  arm64: KVM: Survive unknown traps from guests
  arm: KVM: Survive unknown traps from guests
  KVM: arm/arm64: Let vcpu thread modify its own active state
  KVM: nVMX: reset nested_run_pending if the vCPU is going to be reset
  kvm: nVMX: VMCLEAR should not cause the vCPU to shut down
  KVM: arm/arm64: vgic-v3: Don't pretend to support IRQ/FIQ bypass
  arm64: KVM: VHE: Clear HCR_TGE when invalidating guest TLBs

Pull extable.h fix from Paul Gortmaker:
 "Fixup for arch/score after extable.h introduction.

  It seems that Guenter is the only one on the planet doing builds for
  arch/score -- we don't have compile coverage for it in linux-next or
  in the kbuild-bot either. Guenter couldn't even recall where he got
  his toolchain, but was kind enough to share it with me so I could
  validate this change and also add arch/score to my build coverage.

  I sat on this a bit in case there was any other fallout in other arch
  dirs, but since this still seems to be the only one, I might as well
  send it on its way"

* tag 'extable-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
  score: Fix implicit includes now failing build after extable change

Pull random updates from Ted Ts'o:
 "Change get_random_{int,log} to use the CRNG used by /dev/urandom and
  getrandom(2). It's faster and arguably more secure than cut-down MD5
  that we had been using.

  Also do some code cleanup"

* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
  random: move random_min_urandom_seed into CONFIG_SYSCTL ifdef block
  random: convert get_random_int/long into get_random_u32/u64
  random: use chacha20 for get_random_int/long
  random: fix comment for unused random_min_urandom_seed
  random: remove variable limit
  random: remove stale urandom_init_wait
  random: remove stale maybe_reseed_primary_crng

After changing from module.h to extable.h, score builds fail with:

  arch/score/kernel/traps.c: In function 'do_ri':
  arch/score/kernel/traps.c:248:4: error: implicit declaration of function 'user_disable_single_step'
  arch/score/mm/extable.c: In function 'fixup_exception':
  arch/score/mm/extable.c:32:38: error: dereferencing pointer to incomplete type
  arch/score/mm/extable.c:34:24: error: dereferencing pointer to incomplete type

because extable.h doesn't drag in the same amount of headers as the
module.h did.  Add in the headers which were implicitly expected.

Fixes: 90858794 ("module.h: remove extable.h include now users have migrated")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
[PG: tweak commit log; refresh for sched header refactoring.]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>

Pull tty/serial fixes frpm Greg KH:
 "Here are two bugfixes for tty stuff for 4.11-rc2.

  One of them resolves the pretty bad bug in the n_hdlc code that
  Alexander Popov found and fixed and has been reported everywhere. The
  other just fixes a samsung serial driver issue when DMA fails on some
  systems.

  Both have been in linux-next with no reported issues"

* tag 'tty-4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: samsung: Continue to work if DMA request fails
  tty: n_hdlc: get rid of racy n_hdlc.tbuf

Pull staging driver fixes from Greg KH:
 "Here are two small build warning fixes for some staging drivers that
  Arnd has found on his valiant quest to get the kernel to build
  properly with no warnings.

  Both of these have been in linux-next this week and resolve the
  reported issues"

* tag 'staging-4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: octeon: remove unused variable
  staging/vc04_services: add CONFIG_OF dependency

Pull USB fixes from Greg KH:
 "Here is a number of different USB fixes for 4.11-rc2.

  Seems like there were a lot of unresolved issues that people have been
  finding for this subsystem, and a bunch of good security auditing
  happening as well from Johan Hovold. There's the usual batch of gadget
  driver fixes and xhci issues resolved as well.

 All of these have been in linux-next with no reported issues"

* tag 'usb-4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (35 commits)
  usb: host: xhci-plat: Fix timeout on removal of hot pluggable xhci controllers
  usb: host: xhci-dbg: HCIVERSION should be a binary number
  usb: xhci: remove dummy extra_priv_size for size of xhci_hcd struct
  usb: xhci-mtk: check hcc_params after adding primary hcd
  USB: serial: digi_acceleport: fix OOB-event processing
  MAINTAINERS: usb251xb: remove reference inexistent file
  doc: dt-bindings: usb251xb: mark reg as required
  usb: usb251xb: dt: add unit suffix to oc-delay and power-on-time
  usb: usb251xb: remove max_{power,current}_{sp,bp} properties
  usb-storage: Add ignore-residue quirk for Initio INIC-3619
  USB: iowarrior: fix NULL-deref in write
  USB: iowarrior: fix NULL-deref at probe
  usb: phy: isp1301: Add OF device ID table
  usb: ohci-at91: Do not drop unhandled USB suspend control requests
  USB: serial: safe_serial: fix information leak in completion handler
  USB: serial: io_ti: fix information leak in completion handler
  USB: serial: omninet: drop open callback
  USB: serial: omninet: fix reference leaks at open
  USB: serial: io_ti: fix NULL-deref in interrupt callback
  usb: dwc3: gadget: make to increment req->remaining in all cases
  ...

Pull pinctrl fixes from Linus Walleij:
 "Two smaller pin control fixes for the v4.11 series:

   - Add a get_direction() function to the qcom driver

   - Fix two pin names in the uniphier driver"

* tag 'pinctrl-v4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: uniphier: change pin names of aio/xirq for LD11
  pinctrl: qcom: add get_direction function

The purgatory code defines global variables which are referenced via a
symbol lookup in the kexec code (core and arch).

A recent commit addressing sparse warnings made these static and thereby
broke kexec_file.

Why did this happen? Simply because the whole machinery is undocumented and
lacks any form of forward declarations. The variable names are unspecific
and lack a prefix, so adding forward declarations creates shadow variables
in the core code. Aside of that the code relies on magic constants and
duplicate struct definitions with no way to ensure that these things stay
in sync. The section placement of the purgatory variables happened by
chance and not by design.

Unbreak kexec and cleanup the mess:

 - Add proper forward declarations and document the usage
 - Use common struct definition
 - Use the proper common defines instead of magic constants
 - Add a purgatory_ prefix to have a proper name space
 - Use ARRAY_SIZE() instead of a homebrewn reimplementation
 - Add proper sections to the purgatory variables [ From Mike ]

Fixes: 72042a8c ("x86/purgatory: Make functions and variables static")
Reported-by: Mike Galbraith <&lt;efault@gmx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Nicholas Mc Guire <der.herr@hofr.at>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: "Tobin C. Harding" <me@tobin.cc>
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1703101315140.3681@nanosSigned-off-by: Thomas Gleixner <tglx@linutronix.de>

Pull ceph fixes from Ilya Dryomov:

 - a fix for the recently discovered misdirected requests bug present in
   jewel and later on the server side and all stable kernels

 - a fixup for -rc1 CRUSH changes

 - two usability enhancements: osd_request_timeout option and
   supported_features bus attribute.

* tag 'ceph-for-4.11-rc2' of git://github.com/ceph/ceph-client:
  libceph: osd_request_timeout option
  rbd: supported_features bus attribute
  libceph: don't set weight to IN when OSD is destroyed
  libceph: fix crush_decode() for older maps

Pull i2c fixes from Wolfram Sang:
 "Here are some driver bugfixes from I2C.

  Unusual this time are the two reverts. One because I accidently picked
  a patch from the list which I should have pulled from my co-maintainer
  instead ("missing of_node_put"). And one which I wrongly assumed to be
  an easy fix but it turned out already that it needs more iterations
  ("copy device properties")"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  Revert "i2c: copy device properties when using i2c_register_board_info()"
  Revert "i2c: add missing of_node_put in i2c_mux_del_adapters"
  i2c: exynos5: Avoid transaction timeouts due TRANSFER_DONE_AUTO not set
  i2c: designware: add reset interface
  i2c: meson: fix wrong variable usage in meson_i2c_put_data
  i2c: copy device properties when using i2c_register_board_info()
  i2c: m65xx: drop superfluous quirk structure
  i2c: brcmstb: Fix START and STOP conditions
  i2c: add missing of_node_put in i2c_mux_del_adapters
  i2c: riic: fix restart condition
  i2c: add missing of_node_put in i2c_mux_del_adapters

Pull drm fixes from Dave Airlie:
 "Intel, amd and mxsfb fixes.

  These are the drm fixes I've collected for rc2. Mostly i915 GVT only
  fixes, along with a single EDID fix, some mxsfb fixes and a few minor
  amd fixes"

* tag 'drm-fixes-for-4.11-rc2' of git://people.freedesktop.org/~airlied/linux: (38 commits)
  drm: mxsfb: Implement drm_panel handling
  drm: mxsfb_crtc: Fix the framebuffer misplacement
  drm: mxsfb: Fix crash when provided invalid DT bindings
  drm: mxsfb: fix pixel clock polarity
  drm: mxsfb: use bus_format to determine LCD bus width
  drm/amdgpu: bump driver version for some new features
  drm/amdgpu: validate paramaters in the gem ioctl
  drm/amd/amdgpu: fix console deadlock if late init failed
  drm/i915/gvt: change some gvt_err to gvt_dbg_cmd
  drm/i915/gvt: protect RO and Rsvd bits of virtual vgpu configuration space
  drm/i915/gvt: handle workload lifecycle properly
  drm/edid: Add EDID_QUIRK_FORCE_8BPC quirk for Rotel RSX-1058
  drm/i915/gvt: fix an error for F_RO flag
  drm/i915/gvt: use pfn_valid for better checking
  drm/i915/gvt: set SFUSE_STRAP properly for vitual monitor detection
  drm/i915/gvt: fix an error for one register
  drm/i915/gvt: add more registers into handlers list
  drm/i915/gvt: have more registers with F_CMD_ACCESS flags set
  drm/i915/gvt: add some new MMIOs to cmd_access white list
  drm/i915/gvt: fix pcode mailbox write emulation of BDW
  ...