- 23 Jul, 2021 29 commits
-
-
Roy Sun authored
Squash in warning fix (Alex) Signed-off-by:
Roy Sun <Roy.Sun@amd.com> Reviewed-by:
Zhou pengju <pengju.zhou@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com>
-
Roy Sun authored
The callback functions are used for SRIOV read/write instead of just for rlcg read/write Signed-off-by:
-
Veerabadhran Gopalakrishnan authored
Signed-off-by:
Veerabadhran Gopalakrishnan <veerabadhran.gopalakrishnan@amd.com> Reviewed-by:
James Zhu <James.Zhu@amd.com> Signed-off-by:
-
Jonathan Kim authored
Similar to xGMI reporting the min/max bandwidth between direct peers, PCIe will report the min/max bandwidth to the KFD. Signed-off-by:
Jonathan Kim <jonathan.kim@amd.com> Reviewed-by:
Felix Kuehling <felix.kuehling@amd.com> Signed-off-by:
-
Jonathan Kim authored
Report the min/max bandwidth in megabytes to the kfd for direct xgmi connections only. Indirect peers will report 0 since indirect route is unknown. Signed-off-by:
-
Jonathan Kim authored
The TA can now be invoked to provide the number of xgmi links connecting a direct source and destination peer. Non-direct peers will report zero links. Signed-off-by:
-
Anson Jacob authored
make htmldocs complaints about parameter for amdgpu_bo_add_to_shadow_list ./drivers/gpu/drm/amd/amdgpu/amdgpu_object.c:739: warning: Excess function parameter 'bo' description in 'amdgpu_bo_add_to_shadow_list' ./drivers/gpu/drm/amd/amdgpu/amdgpu_object.c:739: warning: Function parameter or member 'vmbo' not described in 'amdgpu_bo_add_to_shadow_list' ./drivers/gpu/drm/amd/amdgpu/amdgpu_object.c:739: warning: Excess function parameter 'bo' description in 'amdgpu_bo_add_to_shadow_list' Signed-off-by:
Anson Jacob <Anson.Jacob@amd.com> Reviewed-by:
-
Lijo Lazar authored
Add support for board power calibration on Aldebaran. Board calibration is done after DC offset calibration. Signed-off-by:
Lijo Lazar <lijo.lazar@amd.com> Reviewed-by:
Kevin Wang <kevin1.wang@amd.com> Signed-off-by:
-
Eric Yang authored
[Why] PMFW message which previously thought to only control Z9 controls both Z9 and Z10. Also HW design team requested that Z9 must only be supported on eDP due to content protection interop. [How] Change zstate support condition to match updated policy Reviewed-by:
Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com> Acked-by:
Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by:
Eric Yang <Eric.Yang2@amd.com> Signed-off-by:
-
Aric Cyr authored
DC version 3.2.145 brings improvements in multiple areas. In summary, we highlight: - Code improvements for passive - Cursor manipulation enhancements - Expand debug in some areas - Fix problems in DML - Other minor code refactors Reviewed-by:
Aric Cyr <aric.cyr@amd.com> Signed-off-by:
-
Anthony Koo authored
- Add reserved bits for future feature development - Fix issue with mismatch with type const - Replaced problematic code with old memcpy and casted problematic pointers to unsigned char pointers Reviewed-by:
Anthony Koo <Anthony.Koo@amd.com> Signed-off-by:
-
Krunoslav Kovac authored
[why] There's a special case where upper plane is not the main plane. If it owns the cursor, it will be invisible in the majority of the screen. [How] The condition for disabling cursor is changed: - check if upper viewport completely covers current. This was the previous change that doesn't handle all scenarios with pipe splitting. - if not, show the cursor only if it's not scaled or no upper pipe. Reviewed-by:
Krunoslav Kovac <Krunoslav.Kovac@amd.com> Signed-off-by:
-
Bindu Ramamurthy authored
[Why] Populate dtbclk values from bwparams for dcn302, dcn303. [How] dtbclk values are fetched from bandwidthparams for all DPM levels and for DPM levels where smu returns 0, previous level values are reported. Reviewed-by:
Roman Li <Roman.Li@amd.com> Acked-by:
Bindu Ramamurthy <bindu.r@amd.com> Signed-off-by:
-
Eric Yang authored
[Why] When an riommu invalidation request come at the same time as a pipe is disabled there can be a case where DCN cannot ACK the request if only one VMID is setup in the inuse list. [How] Setup a second unused VMID will work around the issue. Reviewed-by:
Jun Lei <jun.lei@amd.com> Acked-by:
-
Nevenko Stupar authored
DCN 3x increased Line buffer size for DCHUB latency hiding, from 4 lines of 4K resolution lines to 5 lines of 4K resolution lines. All Line Buffer can be used as extended memory for P State change latency hiding. The maximum number of lines is increased to 32 lines. Finally, LB_MEMORY_CONFIG_1 (LB memory piece 1) and LB_MEMORY _CONFIG_2 (LB memory piece 2) are not affected, no change in size, only 3 pieces is affected, i.e., when all 3 pieces are used in both LB_MEMORY_CONFIG_0 and LB_MEMORY_CONFIG_3 (for 4:2:0) modes. Reviewed-by:
Nevenko Stupar <Nevenko.Stupar@amd.com> Signed-off-by:
-
Mikita Lipski authored
[why] DCN31 doesn't have MALL in DMUB so to avoid sending unknown commands to DMUB just remove the function pointer. [how] Remove apply_idle_power_optimizations from function pointers structure for DCN31 Reviewed-by:
Mikita Lipski <mikita.lipski@amd.com> Signed-off-by:
-
sunglee authored
[WHY] When finding a second pipe for pipe split, currently will look for bottom pipe in context first to decide the second pipe. This causes issues in 2 plane to 1 plane transitions like fullscreen video where bottom pipe no longer exists in the new configuration. [HOW] If previous context had an ODM pipe, use that to find the secondary pipe first before looking at bottom pipe. Reviewed-by:
Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Acked-by:
sunglee <sunglee@amd.com> Signed-off-by:
-
Camille Cho authored
[Why] We used to unconditionally set backlight path as AUX for panels capable of backlight adjustment via DPCD in set default brightness. [How] This should be limited to OLED panel only since we control backlight via PWM path for SDR mode in LCD HDR panel. Reviewed-by:
Camille Cho <Camille.Cho@amd.com> Signed-off-by:
-
Nicholas Kazlauskas authored
[Why & How] We're missing a default value for dram_channel_width_bytes in the DCN3.1 SOC bounding box and we don't currently have the interface in place to query the actual value from VBIOS. Put in a hardcoded default until we have the interface in place. Reviewed-by:
-
Nicholas Kazlauskas authored
[Why] Hardcoding the VCO frequency isn't correct since we don't own or control the value. In the case where the hardcode is also missing we can't lightup display. [How] Query from the CLK register instead. Update the DFS frequency to be able to compute the VCO frequency. Reviewed-by:
-
Bindu Ramamurthy authored
[Why] Initialize socclk entries in bandwidth params for dcn302, dcn303. [How] Fetch the sockclk values from smu for the DPM levels and for the DPM levels where smu returns 0, previous level values are reported. Reviewed-by:
-
Nicholas Kazlauskas authored
[Why] Vertical and horizontal borders in timings are treated as increasing the active area - vblank and hblank actually shrink. Our input into DML does not include these borders so it incorrectly assumes it has more time than available for vstartup and tmdl calculations for some modes with borders. An example of such a timing would be 640x480@72Hz: h_total: 832 h_border_left: 8 h_addressable: 640 h_border_right: 8 h_front_porch: 16 h_sync_width: 40 v_total: 520 v_border_top: 8 v_addressable: 480 v_border_bottom: 8 v_front_porch: 1 v_sync_width: 3 pix_clk_100hz: 315000 [How] Include borders as part of destination vactive/hactive. This change DCN20+ so it has wide impact, but the destination vactive and hactive are only really used for vstartup calculation anyway. Most modes do not have vertical or horizontal borders. Reviewed-by:
-
Michael Strauss authored
[WHY] Enable feature for 21.40 Reviewed-by:
Sung Lee <Sung.Lee@amd.com> Acked-by:
Michael Strauss <michael.strauss@amd.com> Signed-off-by:
-
Aric Cyr authored
Reviewed-by:
Shahin Khayyer <Shahin.Khayyer@amd.com> Acked-by:
-
Victor Lu authored
[why] A comparison error made it possible to not iterate through all the specified prefetch modes. [how] Correct "<" to "<=" Reviewed-by:
Yongqiang Sun <Yongqiang.Sun@amd.com> Acked-by:
Victor Lu <victorchengchi.lu@amd.com> Signed-off-by:
-
Jake Wang authored
[Why] During headless boot, DIG may be on which causes HW/SW discrepancies. To avoid this we power down hardware on boot if DIG is turned on. With introduction of multiple eDP, hardware power down is being bypassed under certain conditions. [How] Fixed hardware power down bypass, and ensured hardware will power down if DIG is on and seamless boot is not enabled. Reviewed-by:
Jake Wang <haonan.wang2@amd.com> Signed-off-by:
-
Wesley Chalmers authored
Reviewed-by:
Wesley Chalmers <Wesley.Chalmers@amd.com> Signed-off-by:
-
Zhan Liu authored
[Why] Theoretically, per DP 1.4a spec, sink device needs to AUX_ACK 00340h write. However, due to hardware limitation, some sink devices have no 00340h dpcd address at all. This results in sink side fails to reply ACK, and consequently cause source side keep retrying DPCD write on DPCD 00340h. This results in significant delay when DPCD 00340h write is triggered (e.g. at S3 resume). [How] Check whether sink device could ACK on DPCD 00340h write on boot. If sink device fails to ACK, then remember that, so we won't write to DPCD 00340h later on. There will be a drm.debug KMS level message to inform user once a 00340h DPCD write is skipped on purpose. Reviewed-by:
Nikola Cornij <Nikola.Cornij@amd.com> Acked-by:
Zhan Liu <zhan.liu@amd.com> Signed-off-by:
-
Aurabindo Pillai authored
[Why&How] Print a debug message when dcc validation fails in the display driver. Most DCC enablement related errors are from userspace. Adding a debug print in case of a failure from display driver will aid quicker triage. Reviewed-by:
Harry Wentland <Harry.Wentland@amd.com> Acked-by:
Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by:
-
- 21 Jul, 2021 10 commits
-
-
Aric Cyr authored
Acked-by:
-
Anthony Koo authored
- Add reserved bits for future feature development - Fix issue with mismatch with type const Acked-by:
-
Dmytro Laktyushkin authored
This tends to take miliseconds in certain scenarios and we'd rather not wait that long. Due to how this interacts with det size update and locking waiting should not be necessary as compbuf updates before unlock. Add a watch for config error instead as that is something we actually do care about. Acked-by:
-
Ian Chen authored
Reserve padding bytes for new feature implementation Acked-by:
Ian Chen <ian.chen@amd.com> Signed-off-by:
-
Eric Yang authored
[Why] During S4/S5/reboot, sometimes riommu invalidation request arrive too early, DCN may be unable to respond to the invalidation request resulting in pstate hang. [How] VBIOS will force allow pstate for riommu invalidation and driver will clear it after powering down display pipes. Acked-by:
-
Josip Pavic authored
[Why & How] Extend existing state collection functions to add some additional registers useful for debug, and add state collection function for DC hubbub Acked-by:
Josip Pavic <Josip.Pavic@amd.com> Signed-off-by:
-
Mikita Lipski authored
[why] Lowering clocks when entering S2 Idle state causes DMUB to hang with Diags. [how] Do not enter S2 optimization with Diags on dcn301 to prevent DMUB hang. Acked-by:
-
Oliver Logush authored
[why] The units of the time_per_pixel variable were incorrect, this had to be changed for the code to properly function. [how] The change was very straightforward, only required one line of code to be changed where the calculation was done. Acked-by:
Oliver Logush <oliver.logush@amd.com> Signed-off-by:
-
Krunoslav Kovac authored
[why] The current logic checks if there's an upper pipe whose viewport completely covers the current pipe viewport. This fails in pipe splitting case as you can have layer 1 pipe that crosses the two layer 0 pipes where it's contained in both, but neither covers it completely, hence we allow the cursor on both layers. [How] Instead of trying to "sum up" rectangles from the higher level pipes which could leave gaps and would not work generically, we will assume if there's an upper layer that is active, it will control the HW cursor. Acked-by:
-
Charlene Liu authored
[why] currently dc has never reset this dpcd_cap.dpcd_rev. [how] ideally we should reset this before redo detection. change the passive dongle only for now to reduce the impact. Acked-by:
Charlene Liu <Charlene.Liu@amd.com> Signed-off-by:
-
- 16 Jul, 2021 1 commit
-
-
Liviu Dudau authored
Commit 72a7cf0a ("drm/amd/display: Keep linebuffer pixel depth at 30bpp for DCE-11.0.") doesn't seems to have fixed 10bit 4K rendering over DisplayPort for CIK GPUs. On my machine with a HAWAII GPU I get a broken image that looks like it has an effective resolution of 1920x1080 but scaled up in an irregular way. Reverting the commit or applying this patch fixes the problem on v5.14-rc1. Fixes: 72a7cf0a ("drm/amd/display: Keep linebuffer pixel depth at 30bpp for DCE-11.0.") Acked-by:
Mario Kleiner <mario.kleiner.de@gmail.com> Reviewed-by:
Liviu Dudau <liviu@dudau.co.uk> Signed-off-by:
-
