- 16 Dec, 2018 10 commits
-
-
Mantas Mikulėnas authored
Tested with 4.19.9. v2: Changed from CXT_FIXUP_MUTE_LED_GPIO to CXT_FIXUP_HP_DOCK because that's what the existing fixups for EliteBooks use. Signed-off-by:Mantas Mikulėnas <grawity@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by:
Takashi Iwai <tiwai@suse.de>
-
Takashi Sakamoto authored
As a result of investigation for Fireface 800, 'struct snd_ff_spec.regs' is just for higher address to receive tx asynchronous packets of MIDI messages, thus it can be simplified. This commit simplifies it. Signed-off-by:
Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by:
-
Takashi Sakamoto authored
This commit adds a functionality to multiplex PCM frames into isochronous packets and demultiplex PCM frames from isochronous packets for ALSA PCM applications. Fireface 800 voluntarily maintains resources for tx isochronous communication. It performs reservation of isochronous channel and allocation/update of bandwidth in some cases below: - at a first request to allocation after bus resets - at requests to allocation when further bandwidth is required When request is grant and the unit is prepared, read data from 0x0000801c0008 represents isochronous channel for tx stream, then the unit can handle requests to start communication. If driver send the request without checking the register, the unit takes panic to continue bus resets. The unit starts transmission of tx packets after receiving several rx packets from driver. I note that the unit can process tx/rx packets and generate/record sound regardless of HOST LED. Signed-off-by:
-
Takashi Sakamoto authored
The way to maintain isochronous resources on bus is different between Fireface 400/800. This commit is a preparation. This commit moves a function to allocate resource to model-dependent implementation. Signed-off-by:
-
Takashi Sakamoto authored
Fireface 400/800 use three modes against the number of data channels in data block for both tx/rx packets. This commit adds refactoring for it. Some enumerators are added to represent each of mode and a function is added to calculate the mode from sampling frequency code (sfc). Signed-off-by:
-
Takashi Sakamoto authored
Both of Fireface 400/800 have the same register to switch frame fetching mode regardless of difference of available number of PCM frames in rx isochronous packet. This commit moves a helper function from model-dependent implementation. Signed-off-by:
-
Takashi Sakamoto authored
According to my memo at hand and saved records, writing 0x00000001 to SND_FF_REG_FETCH_PCM_FRAMES disables fetching PCM frames in corresponding channel, however current implement uses reversed logic. This results in muted volume in device side during playback. This commit corrects the bug. Cc: <stable@vger.kernel.org> # v4.12+ Fixes: 76fdb3a9 ('ALSA: fireface: add support for Fireface 400') Signed-off-by:
-
Takashi Sakamoto authored
An initial commit to add tracepoints for packets without CIP headers uses different print formats for added tracepoints. However this is not convenient for users/developers to prepare debug tools. This commit uses the same format for the two tracepoints. Cc: <stable@vger.kernel.org> # v4.12+ Fixes: b164d2fd ('ALSA: firewire_lib: add tracepoints for packets without CIP headers') Signed-off-by:
-
Takashi Sakamoto authored
An initial commit to add tracepoints for packets without CIP headers introduces a wrong assignment to 'data_blocks' value of 'out_packet_without_header' tracepoint. This commit fixes the bug. Cc: <stable@vger.kernel.org> # v4.12+ Fixes: b164d2fd ('ALSA: firewire_lib: add tracepoints for packets without CIP headers') Signed-off-by:
-
Takashi Sakamoto authored
In IEC 61883-1/6 engine of ALSA firewire stack, a packet handler has a second argument for 'the number of bytes in payload of isochronous packet'. However, an incoming packet handler without CIP header uses the value as 'the number of quadlets in the payload'. This brings userspace applications to receive the number of PCM frames as four times against real time. This commit fixes the bug. Cc: <stable@vger.kernel.org> # v4.12+ Fixes: 3b196c39 ('ALSA: firewire-lib: add no-header packet processing') Signed-off-by:
-
- 13 Dec, 2018 7 commits
-
-
Takashi Iwai authored
Pull Huawei LEDS and hotkey support. Signed-off-by: -
Ayman Bagabas authored
Some of Huawei laptops come with a LED in the micmute key. This patch enables the use of micmute LED for these devices: 1. Matebook X (19e5:3200), (19e5:3201) 2. Matebook X Pro (19e5:3204) Reviewed-by:
Andy Shevchenko <andy.shevchenko@gmail.com> Reviewed-by:
Ayman Bagabas <ayman.bagabas@gmail.com> Signed-off-by:
-
Ayman Bagabas authored
This driver adds support for missing hotkeys on some Huawei laptops. Laptops such as the Matebook X have non functioning hotkeys. Whereas newer laptops such as the Matebook X Pro come with working hotkeys out of the box. Old laptops, such as the Matebook X, report hotkey events through ACPI device "\WMI0". However, new laptops, such as the Matebook X Pro, does not have this WMI device. All the hotkeys on the Matebook X Pro work fine without this patch except (micmute, wlan, and huawei key). These keys and the brightness keys report events to "\AMW0" ACPI device. One problem is that brightness keys on the Matebook X Pro work without this patch. This results in reporting two brightness key press events one is captured by ACPI and another by this driver. A solution would be to check if such event came from the "\AMW0" WMI driver then skip reporting event. Another solution would be to leave this to user-space to handle. Which can be achieved by using "hwdb" tables and remap those keys to "unknown". This solution seems more natural to me because it leaves the decision to user-space. Acked-by:
-
Ayman Bagabas authored
This patch solves bug 200501 'Only 2 of 4 speakers playing sound.' It enables the front speakers on Huawei Matebook X Pro laptops. These laptops come with Dolby Atmos sound system and these pins configuration enables the front speakers. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=200501Reviewed-by:
-
Gustavo A. R. Silva authored
stream is indirectly controlled by user-space, hence leading to a potential exploitation of the Spectre variant 1 vulnerability. This issue was detected with the help of Smatch: sound/core/pcm.c:140 snd_pcm_control_ioctl() warn: potential spectre issue 'pcm->streams' [r] (local cap) Fix this by sanitizing stream before using it to index pcm->streams Notice that given that speculation windows are large, the policy is to kill the speculation on the first load and not worry if it can be completed with a dependent load/store [1]. [1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2Signed-off-by:
Gustavo A. R. Silva <gustavo@embeddedor.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Gustavo A. R. Silva authored
info.mode and info.port are indirectly controlled by user-space, hence leading to a potential exploitation of the Spectre variant 1 vulnerability. These issues were detected with the help of Smatch: sound/synth/emux/emux_hwdep.c:72 snd_emux_hwdep_misc_mode() warn: potential spectre issue 'emu->portptrs[i]->ctrls' [w] (local cap) sound/synth/emux/emux_hwdep.c:75 snd_emux_hwdep_misc_mode() warn: potential spectre issue 'emu->portptrs' [w] (local cap) sound/synth/emux/emux_hwdep.c:75 snd_emux_hwdep_misc_mode() warn: potential spectre issue 'emu->portptrs[info.port]->ctrls' [w] (local cap) Fix this by sanitizing both info.mode and info.port before using them to index emu->portptrs[i]->ctrls, emu->portptrs[info.port]->ctrls and emu->portptrs. Notice that given that speculation windows are large, the policy is to kill the speculation on the first load and not worry if it can be completed with a dependent load/store [1]. [1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2Signed-off-by:
-
Takashi Iwai authored
Pull refactoring / fixes of HD-audio PM and display power management Signed-off-by:
-
- 11 Dec, 2018 15 commits
-
-
Takashi Sakamoto authored
Fireface 800 is a flagship model of RME GmbH for audio and music units on IEEE 1394 bus, shipped 2004. This model consists of four chips: - TI TSB81BA3D for physical layer on cable environment of EEE 1394 bus - TI TSB82AA2 for link layer for 1394 OHCI bus bridge to PCI bus - Xilinx Spartan-3 FPGA XC3S400 - Xilinx High-Performance CPLD XC9572XL This commit adds support Fireface 800. In this time, the support is restricted to its MIDI functionality, thus this commit adds some condition statements to avoid touching streaming functionality. Unlike Fireface 400, Fireface 800 has no functionality to suppress asynchronous transactions for MIDI messages except for unregister of listen address in controller side, thus the feature is available as is. Signed-off-by:
-
Takashi Sakamoto authored
Content of asynchronous transaction for MIDI messages differs between Fireface 400 and 800. This commit adds a model-specific handler for the transaction and adds arrangement. Signed-off-by:
-
Takashi Sakamoto authored
Fireface 400 and 800 have the same mechanism to decide address to which asynchronous transactions are sent for MIDI messages, however they use different registers for controllers to notify higher 4 byte of the address. This commit adds a model-specific parameter to represent the address. Additionally, it corrects some comments. I note that these two models have a difference to enable/disable the transaction. Signed-off-by:
-
Takashi Sakamoto authored
As long as investigating packet dumps from Fireface 400/800, a register to receive asynchronous transactions for MIDI messages is the same. For Fireface 800, minor register is used. This commit declares macros for the transactions and obsoletes model-specific parameters. Signed-off-by:
-
Takashi Sakamoto authored
Unlike Fireface 400, Fireface 800 have two pair of optical interface for ADAT signal and S/PDIF signal. ADAT signals for the interface are handled for sampling clock source separately. This commit modifies a parser for clock configuration to distinguish these two ADAT signals. Signed-off-by:
-
Takashi Sakamoto authored
As long as investigating packet dumps from Fireface 400/800, bits on status registers for clock synchronization are the same. This commit moves a parser for a register of clock configuration to obsolete model-specific operations. Signed-off-by:
-
Takashi Sakamoto authored
As long as investigating packet dumps from Fireface 400/800, bits on status registers for clock synchronization are the same. This commit moves a parser for the registers to obsolete model-specific operations. Signed-off-by:
-
Takashi Sakamoto authored
As long as investigating packet dumps from Fireface 400/800, status registers for clock synchronization is common. This commit moves some macros for them to header file. Signed-off-by:
-
Arnd Bergmann authored
When building without CONFIG_PCI, we can (depending on the architecture) get a link failure: ERROR: "pci_iounmap" [sound/pci/hda/snd-hda-codec-ca0132.ko] undefined! Adding a compile-time check for PCI gets it to work correctly on 32-bit ARM. Fixes: d99501b8 ("ALSA: hda/ca0132 - Call pci_iounmap() instead of iounmap()") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Takashi Iwai authored
We've excluded the display_power_control flag for Intel HSW and BDW codecs as the HD-audio controllers of the corresponding platforms take care of the display power as well. But the recent refactoring separates the controller and the codec power accounting, so it's fine to call the display PM even for HSW/BDW codecs. This is less confusing since we can avoid this well-hidden condition. Signed-off-by: -
Takashi Iwai authored
The display power is in unbalance at removing the driver since it misses the snd_hdac_display_power(OFF) call. Acked-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Takashi Iwai authored
After the recent refactoring, snd_hdac_display_power() doesn't return any error, hence it can be defined to return void. This makes many error checks redundant and allows us to reduce them gracefully. Signed-off-by: -
Takashi Iwai authored
When an error occurs in azx_probe_continue(), we should release the display power. However, the current code ignores it and releases the display power only for HSW/BDW cases. Fix it. Signed-off-by: -
Takashi Iwai authored
snd_hdac_display_power() can be called even for a HDA controller without DRM binding. The same is true for other helpers, snd_hdac_i915_set_bclk() and snd_hdac_set_codec_wakeup(). So all superfluous AZX_DCAPS_I915_POWERWELL checks in hda_intel.c can be dropped, and the definition of AZX_DCAPS_I915_POWERWELL itself can be removed as well. This simplifies the code a lot. Signed-off-by: -
Takashi Iwai authored
The current HD-audio code manages the DRM audio power via too complex redirections, and this seems even still unbalanced in a corner case as Intel DRM CI has been intermittently reporting. This patch is a big surgery for addressing the complexity and the possible unbalance. Basically the patch changes the display PM in the following ways: - Both HD-audio controller and codec drivers call a single helper, snd_hdac_display_power(). (Formerly, the display power control from a codec was done indirectly via link_power bus ops.) - snd_hdac_display_power() receives the codec address index. For turning on/off from the controller, pass HDA_CODEC_IDX_CONTROLLER. - snd_hdac_display_power() doesn't manage refcounts any longer, but keeps the power status in bitmap. If any of controller or codecs is turned on, the function updates the DRM power state via get_power() or put_power(). Also this refactor allows us more cleanup: - The link_power bus ops is dropped, so there is no longer indirect management, as mentioned in the above. - hdac_device link_power_control flag is moved to hda_codec display_power_control flag, as it's only for HDA legacy. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106525Signed-off-by:
-
- 10 Dec, 2018 4 commits
-
-
Takashi Iwai authored
Back-merge for resolving the conflict of fixup entries added in both branches. Signed-off-by: -
Jian-Hong Pan authored
The ASUS UX433FN and UX333FA with ALC294 cannot detect the headset MIC and output through the internal speaker and the headphone until ALC294_FIXUP_ASUS_SPK and ALC294_FIXUP_ASUS_HEADSET_MIC quirk applied. Signed-off-by:
Daniel Drake <drake@endlessm.com> Signed-off-by:
Jian-Hong Pan <jian-hong@endlessm.com> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Jian-Hong Pan authored
The ASUS UX533FD with ALC294 cannot detect the headset MIC and outputs through the internal speaker and the headphone until ALC294_FIXUP_ASUS_SPK and ALC294_FIXUP_ASUS_HEADSET_MIC quirk applied. Signed-off-by:
-
Chris Chiu authored
The known ALC256_FIXUP_ASUS_MIC fixup can fix the headphone jack sensing and enable use of the internal microphone on this laptop X542UN. However, it's ALC294 so create a new fixup named ALC294_FIXUP_ASUS_MIC to avoid confusion. Signed-off-by:
Chris Chiu <chiu@endlessm.com> Cc: <stable@vger.kernel.org> Signed-off-by:
-
- 09 Dec, 2018 3 commits
-
-
Takashi Iwai authored
Make unified suspend / resume helpers and call them from both the runtime- and the system-PM callbacks for simplifying code. There are slight changes of call orders, but there shouldn't be any functional difference after refactoring. Signed-off-by: -
Takashi Sakamoto authored
In an initial commit, 'SYNC_STATUS' register is referred to get clock configuration, however this is wrong, according to my local note at hand for reverse-engineering about packet dump. It should be 'CLOCK_CONFIG' register. Actually, ff400_dump_clock_config() is correctly programmed. This commit fixes the bug. Cc: <stable@vger.kernel.org> # v4.12+ Fixes: 76fdb3a9 ('ALSA: fireface: add support for Fireface 400') Signed-off-by:
-
Hui Wang authored
Users reported a mute LED regression on Lenovo X1 Carbon, the root cause is we applied the fixup of ALC285_FIXUP_LENOVO_HEADPHONE_NOISE to this machine, then the machine can't apply the fixup of ALC269_FIXUP_THINKPAD_ACPI anymore. To fix it, we chain two fixup together. Fixes: c4cfcf6f ("ALSA: hda/realtek - fix the pop noise on headphone for lenovo laptops") Cc: <stable@vger.kernel.org> Signed-off-by:
Hui Wang <hui.wang@canonical.com> Signed-off-by:
-
- 07 Dec, 2018 1 commit
-
-
Kailang Yang authored
This patch will enable headset button for new Chrome platform. Signed-off-by:
Kailang Yang <kailang@realtek.com> Signed-off-by:
-
