If ret isn't zero, it is almost for sure ETIMEDOUT, because
we use it in wait_for macro which does continuous retries
until timeout is reached. If we still ran out of time and
retries, we most likely would be interested in getting status,
to understand what was the actual error propagated from PCode,
rather than to find out that we had a time out, which is anyway
quite obvious, if the function fails.

v2: Make it status ? status : ret(thanks Vinod for the hint)
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Reviewed-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220411081343.18099-1-stanislav.lisovskiy@intel.com

Currently skl_pcode_try_request function doesn't
properly handle return value it gets from
snb_pcode_rw, but treats status != 0 as success,
returning true, which basically doesn't allow
to use retry/timeout mechanisms if PCode happens
to be busy and returns EGAIN or some other status
code not equal to 0.

We saw this on real hw and also tried simulating this
by always returning -EAGAIN from snb_pcode_rw for 6 times, which
currently will just result in false success, while it should
have tried until timeout is reached:

[   22.357729] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Changing CDCLK to
307200 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
[   22.357831] i915 0000:00:02.0: [drm:__snb_pcode_rw [i915]] Returning EAGAIN retry 1
[   22.357892] i915 0000:00:02.0: [drm:skl_pcode_request [i915]] Success, exiting
[   22.357936] i915 0000:00:02.0: [drm] ERROR Failed to inform PCU about cdclk change (err -11, freq 307200)

We see en error because higher level api, still notices that status was wrong,
however we still did try only once.

We fix it by requiring _both_ the status to be 0 and
request/reply match for success(true) and function
should return failure(false) if either status turns
out to be EAGAIN, EBUSY or whatever or reply/request
masks do not match.

So now we see this in the logs:

[   22.318667] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Changing CDCLK to
307200 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
[   22.318782] i915 0000:00:02.0: [drm:__snb_pcode_rw [i915]] Returning EAGAIN retry 1
[   22.318849] i915 0000:00:02.0: [drm:__snb_pcode_rw [i915]] Returning EAGAIN retry 2
[   22.319006] i915 0000:00:02.0: [drm:__snb_pcode_rw [i915]] Returning EAGAIN retry 3
[   22.319091] i915 0000:00:02.0: [drm:__snb_pcode_rw [i915]] Returning EAGAIN retry 4
[   22.319158] i915 0000:00:02.0: [drm:__snb_pcode_rw [i915]] Returning EAGAIN retry 5
[   22.319224] i915 0000:00:02.0: [drm:__snb_pcode_rw [i915]] Returning EAGAIN retry 6
Reviewed-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220408125200.9069-2-stanislav.lisovskiy@intel.com

Sync up with v5.18-rc1, in particular to get 5e3094cf
("drm/i915/xehpsdv: Add has_flat_ccs to device info").
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

Commit 4b276ed3 ("drm/i915/uncore: Warn on previous unclaimed
accesses") tried to improve our report of unclaimed register access,
however it unveiled cases that were not previously causing any harm.

Downgrade the first message to debug so we can still see them and
eventually fix, but don't warn.

Fixes: 4b276ed3 ("drm/i915/uncore: Warn on previous unclaimed accesses")
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220408164837.3845786-1-lucas.demarchi@intel.com

Commit 3b6f4095 ("drm/i915/display/psr: Lock and unlock PSR around
pipe updates") did not took into account async flips with PSR1 and
PSR2 HW tracking, causing PSR lock not be held and causing warnings
when intel_psr2_program_trans_man_trk_ctl() is executed.

So here taking the PSR lock before the earlier return in
intel_pipe_update_start/end().

Cc: Jouni Högander <jouni.hogander@intel.com>
Reported-by: Imre Deak <imre.deak@intel.com>
Fixes: 3b6f4095 ("drm/i915/display/psr: Lock and unlock PSR around pipe updates")
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220406210540.493610-1-jose.souza@intel.com

Since gen6 we use FPGA_DBG register to detect unclaimed MMIO registers.
This register is in the display engine IP and can only ever detect
unclaimed accesses to registers in this area. However sometimes there
are reports of this triggering for registers in other areas, which
should not be possible.

Right now we always warn after the read/write of registers going through
unclaimed_reg_debug(). However places using __raw_uncore_* may be
triggering the unclaimed access and those being later accounted to a
different register. Let's warn both before and after the read/write
with a slightly different message, so it's clear if the register
reported in the warning is actually the culprit.

Commit dda96033 ("drm/i915: Just clear the mmiodebug before a
register access") attempted to solve the same issue by removing the
warning when if FPGA_DBG flags before the mmio read/write. However, it
doesn't solve it completely as FPGA_DBG may remain set when reading
registers outside display. So in the end the check after the mmio
read/write triggers the warning pointing to the wrong register.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220405001149.2675226-1-lucas.demarchi@intel.com

Accessing the DDI_BUF_CTL register without the port's DDI clock being
enabled (to set/clear the TypeC PHY ownership for the port) can lead to
a corrupted value read during any i915 register access right after the
DDI clock is enabled.

The root cause is the way clock synchronization works for this register,
controlled by the CHICKEN_DCPR_1 DDI_CLOCK_REG_ACCESS flag. Correctly
this flag should be cleared on ADLP (see the Bspec link below), however
after bootup the flag is set.

One easily reproducible issue is an unclaimed register access of the
PWR_WELL_CTL_DDI2 register, programmed right after DDI clock enabling to
enable the port's DDI_IO power well (see the HSDES, VLK links below).
With the correct setting above this problem can't be reproduced.

Bspec: 49189
HSDES: 18019028154
VLK: 28328, 28655

Cc: Jouni Högander <jouni.hogander@intel.com>
Cc: Arthur J Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Acked-by: Arthur J Runyan <arthur.j.runyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220323201749.288566-1-imre.deak@intel.com

Split i915_run_as_guest() into a more arch-friendly function
as non-x86 builds do not support this functionality.
Signed-off-by: Casey Bowman <casey.g.bowman@intel.com>
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220331204343.1256150-2-casey.g.bowman@intel.com

Instead of exit PSR when a frontbuffer invalidation happens, we can
enable the PSR2 selective fetch continuous full frame, that will keep
the panel updated like PSR was disabled but without keeping PSR active.

So as soon as the frontbuffer flush happens we can disable the
continuous full frame and start to do selective fetches much quicker
than the path that would enable PSR, that will wait a few frames
to actually activate PSR.

Also this approach has proven to fix some glitches found in Alderlake-P
when there are a lot of invalidations happening together with page
flips.

Some may ask why it is writing to CURSURFLIVE(), it is because
that is the way that hardware team provided us to poke display to
handle PSR updates, and it is being used since display 9.

v2:
- handling possible race conditions between frontbuffer rendering and
page flips
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Cc: Khaled Almahallawy <khaled.almahallawy@intel.com>
Cc: Shawn C Lee <shawn.c.lee@intel.com>
Cc: Jouni Högander <jouni.hogander@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220405155344.47219-3-jose.souza@intel.com

Frontbuffer rendering and page flips can race with each other
and this can potentialy cause issues with PSR2 selective fetch.

And because pipe/crtc updates are time sentive we can't grab the
PSR lock after intel_pipe_update_start() and before
intel_pipe_update_end().

So here adding the lock and unlock functions and calls, the
proper PSR2 selective fetch handling will come in a separated patch.

v2:
- fixed new functions documentation
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Cc: Jouni Högander <jouni.hogander@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220405155344.47219-2-jose.souza@intel.com

Following up what was done in commit 804f4688 ("drm/i915/psr: Set
"SF Partial Frame Enable" also on full update") and also setting
partial frame enable when psr_force_hw_tracking_exit() is called.

Also as PSR2_MAN_TRK_CTL is a double buffered registers do a RMW
is not a good idea so here also setting the man_trk_ctl_enable_bit()
that is required in TGL and only doing a register write.

v2:
- not doing a rmw

v3:
- removing the inline from functions that return PSR2_MAN_TRK_CTL
bits
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Cc: Jouni Högander <jouni.hogander@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220405155344.47219-1-jose.souza@intel.com

Because VLV_GT_RENDER_RC6 == GEN6_GT_GFX_RC6, the IS_VALLEYVIEW() check is
not needed. Neither is the check present in other code paths which call
intel_rc6_residency_ns() (in functions gen6_drpc(), rc6_residency() and
rc6_residency_ms_show()).

v2: Elimintate VLV_GT_RENDER_RC6 #define (Jani)

Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Reviewed-by: Badal Nilawar <badal.nilawar@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220314161310.6468-1-ashutosh.dixit@intel.com

The request to aqquire gem resources is failing for DSB in rare
scenario where it is busy and the register programming will be done
through mmio fallback path.

DSB has extra advantage of faster register programming which may
go away through mmio path. Adding wait for gem resource also may
not be right as anyways losing time.

To make the CI execution happy replaced drm_err() to drm_info()
for printing debug info during dsb buffer preparation.

v1: Initial version.
v2: Added print for mmio fallback at out label. [Nirmoy]
v3: Improved debug message. [Nirmoy]

Cc: Nirmoy Das <nirmoy.das@linux.intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220325161140.11906-1-animesh.manna@intel.comReviewed-by: Nirmoy Das <nirmoy.das@intel.com>

Our YCbCr output is always supposed to be limited range BT.709.
That's what we send with native HDMI. The conn_state->colorspace
stuff is entirely independent of that and is not supposed to alter
the generated output in any way. If we want a way to do that then
we need a new proprty for it.

Make it so that the RGB->YCbCr conversion when performed by the
DPF will match the BT.709 we would transmit with native HDMI.

Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220322120015.28074-12-ville.syrjala@linux.intel.comReviewed-by: Uma Shankar <uma.shankar@intel.com>

With native HDMI we allow the user to override the mode with
something that may not respect the downstream (sink,dual-mode adapter)
TMDS clock limits. Let's reuse the same logic for DP HDMI DFPs
so that behaviour is more or less uniform.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220322120015.28074-11-ville.syrjala@linux.intel.comReviewed-by: Uma Shankar <uma.shankar@intel.com>

Currently we only support "4:2:0 also" modes on native HDMI.
Extend that support for DP as well.

With all the HDMI DFP TMDS clock handling sorted out this
is now going to work for both native DP and DP->HDMI
converters. As with native HDMI we first check if RGB
output is possible, and if not we try YCbCr 4:2:0 instead.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220322120015.28074-10-ville.syrjala@linux.intel.comReviewed-by: Uma Shankar <uma.shankar@intel.com>

Rework the HDMI DFP TMDS clock checks to also check at 8bpc.
Previously we only checked the deep color cases. But I suppose
a sink could potentially declare "4:2:0 also" modes that only
actually fit within its own limits when using 4:2:0. Even if
that is too nuts to be real there is no real harm in running
through the full checks for everything.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220322120015.28074-9-ville.syrjala@linux.intel.comReviewed-by: Uma Shankar <uma.shankar@intel.com>

Hoist the drm_mode_is_420_only() from intel_dp_output_format()
into the caller. This will allow intel_dp_output_format() to be
reused for "4:2:0 also" modes.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220322120015.28074-8-ville.syrjala@linux.intel.comReviewed-by: Uma Shankar <uma.shankar@intel.com>

Prefer to use intel_connector over drm_connector. Also clean
up the related variable names a bit.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220322120015.28074-7-ville.syrjala@linux.intel.comReviewed-by: Uma Shankar <uma.shankar@intel.com>

Consolidate the double pfit call, and reorder things so that
intel_dp_output_format() and intel_dp_compute_link_config() are
back-to-back. They are intimately related, and will need to be
called twice to properly handle the "4:2:0 also" modes.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220322120015.28074-6-ville.syrjala@linux.intel.comReviewed-by: Uma Shankar <uma.shankar@intel.com>

intel_dp_hdmi_ycbcr420() does account for native DP 4:2:0
output as well, so lets rename it a bit.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220322120015.28074-5-ville.syrjala@linux.intel.comReviewed-by: Uma Shankar <uma.shankar@intel.com>

Declutter intel_dp_compute_config() a bit by moving the
has_audio computation into a helper. HDMI already does the same thing.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220322120015.28074-4-ville.syrjala@linux.intel.comReviewed-by: Uma Shankar <uma.shankar@intel.com>

Currently we only look at the DFPs max TMDS clock limit when
considering whether the mode is valid, or whether we can do
deep color. The sink's max TMDS clock limit may be lower than
the DFPs, so we need to account for it as well.

Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4095
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2844Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220322120015.28074-3-ville.syrjala@linux.intel.comReviewed-by: Uma Shankar <uma.shankar@intel.com>

We're currently duplicating the DFP min/max TMDS clock checks
in .mode_valid() and .compute_config(). Extract a helper suitable
for both use cases.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220322120015.28074-2-ville.syrjala@linux.intel.comReviewed-by: Uma Shankar <uma.shankar@intel.com>

All the LFP data table pointers have uniform layout. Turn
that into a struct.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220317171948.10400-2-ville.syrjala@linux.intel.comReviewed-by: Jani Nikula <jani.nikula@intel.com>

Remove some zombies from our device structure.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220321195006.775-4-ville.syrjala@linux.intel.comReviewed-by: Jani Nikula <jani.nikula@intel.com>

Stop hand rolling drm_connector_attach_hdr_output_metadata_property().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220321195006.775-3-ville.syrjala@linux.intel.comReviewed-by: Jani Nikula <jani.nikula@intel.com>

Pull more tracing updates from Steven Rostedt:

 - Rename the staging files to give them some meaning. Just
   stage1,stag2,etc, does not show what they are for

 - Check for NULL from allocation in bootconfig

 - Hold event mutex for dyn_event call in user events

 - Mark user events to broken (to work on the API)

 - Remove eBPF updates from user events

 - Remove user events from uapi header to keep it from being installed.

 - Move ftrace_graph_is_dead() into inline as it is called from hot
   paths and also convert it into a static branch.

* tag 'trace-v5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Move user_events.h temporarily out of include/uapi
  ftrace: Make ftrace_graph_is_dead() a static branch
  tracing: Set user_events to BROKEN
  tracing/user_events: Remove eBPF interfaces
  tracing/user_events: Hold event_mutex during dyn_event_add
  proc: bootconfig: Add null pointer check
  tracing: Rename the staging files for trace_events

Pull clk fix from Stephen Boyd:
 "A single revert to fix a boot regression seen when clk_put() started
  dropping rate range requests. It's best to keep various systems
  booting so we'll kick this out and try again next time"

* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  Revert "clk: Drop the rate range on clk_put()"

Pull x86 fixes from Thomas Gleixner:
 "A set of x86 fixes and updates:

   - Make the prctl() for enabling dynamic XSTATE components correct so
     it adds the newly requested feature to the permission bitmap
     instead of overwriting it. Add a selftest which validates that.

   - Unroll string MMIO for encrypted SEV guests as the hypervisor
     cannot emulate it.

   - Handle supervisor states correctly in the FPU/XSTATE code so it
     takes the feature set of the fpstate buffer into account. The
     feature sets can differ between host and guest buffers. Guest
     buffers do not contain supervisor states. So far this was not an
     issue, but with enabling PASID it needs to be handled in the buffer
     offset calculation and in the permission bitmaps.

   - Avoid a gazillion of repeated CPUID invocations in by caching the
     values early in the FPU/XSTATE code.

   - Enable CONFIG_WERROR in x86 defconfig.

   - Make the X86 defconfigs more useful by adapting them to Y2022
     reality"

* tag 'x86-urgent-2022-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/fpu/xstate: Consolidate size calculations
  x86/fpu/xstate: Handle supervisor states in XSTATE permissions
  x86/fpu/xsave: Handle compacted offsets correctly with supervisor states
  x86/fpu: Cache xfeature flags from CPUID
  x86/fpu/xsave: Initialize offset/size cache early
  x86/fpu: Remove unused supervisor only offsets
  x86/fpu: Remove redundant XCOMP_BV initialization
  x86/sev: Unroll string mmio with CC_ATTR_GUEST_UNROLL_STRING_IO
  x86/config: Make the x86 defconfigs a bit more usable
  x86/defconfig: Enable WERROR
  selftests/x86/amx: Update the ARCH_REQ_XCOMP_PERM test
  x86/fpu/xstate: Fix the ARCH_REQ_XCOMP_PERM implementation

Pull RT signal fix from Thomas Gleixner:
 "Revert the RT related signal changes. They need to be reworked and
  generalized"

* tag 'core-urgent-2022-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  Revert "signal, x86: Delay calling signals in atomic on RT enabled kernels"

Pull more dma-mapping updates from Christoph Hellwig:

 - fix a regression in dma remap handling vs AMD memory encryption (me)

 - finally kill off the legacy PCI DMA API (Christophe JAILLET)

* tag 'dma-mapping-5.18-1' of git://git.infradead.org/users/hch/dma-mapping:
  dma-mapping: move pgprot_decrypted out of dma_pgprot
  PCI/doc: cleanup references to the legacy PCI DMA API
  PCI: Remove the deprecated "pci-dma-compat.h" API

Pull ARM fixes from Russell King:

 - avoid unnecessary rebuilds for library objects

 - fix return value of __setup handlers

 - fix invalid input check for "crashkernel=" kernel option

 - silence KASAN warnings in unwind_frame

* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: 9191/1: arm/stacktrace, kasan: Silence KASAN warnings in unwind_frame()
  ARM: 9190/1: kdump: add invalid input check for 'crashkernel=0'
  ARM: 9187/1: JIVE: fix return value of __setup handler
  ARM: 9189/1: decompressor: fix unneeded rebuilds of library objects

This reverts commit 7dabfa2b. There are
multiple reports that this breaks boot on various systems. The common
theme is that orphan clks are having rates set on them when that isn't
expected. Let's revert it out for now so that -rc1 boots.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Reported-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Link: https://lore.kernel.org/r/366a0232-bb4a-c357-6aa8-636e398e05eb@samsung.com
Cc: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20220403022818.39572-1-sboyd@kernel.org

Merge tag 'perf-tools-for-v5.18-2022-04-02' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux

Pull more perf tools updates from Arnaldo Carvalho de Melo:

 - Avoid SEGV if core.cpus isn't set in 'perf stat'.

 - Stop depending on .git files for building PERF-VERSION-FILE, used in
   'perf --version', fixing some perf tools build scenarios.

 - Convert tracepoint.py example to python3.

 - Update UAPI header copies from the kernel sources: socket,
   mman-common, msr-index, KVM, i915 and cpufeatures.

 - Update copy of libbpf's hashmap.c.

 - Directly return instead of using local ret variable in
   evlist__create_syswide_maps(), found by coccinelle.

* tag 'perf-tools-for-v5.18-2022-04-02' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
  perf python: Convert tracepoint.py example to python3
  perf evlist: Directly return instead of using local ret variable
  perf cpumap: More cpu map reuse by merge.
  perf cpumap: Add is_subset function
  perf evlist: Rename cpus to user_requested_cpus
  perf tools: Stop depending on .git files for building PERF-VERSION-FILE
  tools headers cpufeatures: Sync with the kernel sources
  tools headers UAPI: Sync drm/i915_drm.h with the kernel sources
  tools headers UAPI: Sync linux/kvm.h with the kernel sources
  tools kvm headers arm64: Update KVM headers from the kernel sources
  tools arch x86: Sync the msr-index.h copy with the kernel sources
  tools headers UAPI: Sync asm-generic/mman-common.h with the kernel
  perf beauty: Update copy of linux/socket.h with the kernel sources
  perf tools: Update copy of libbpf's hashmap.c
  perf stat: Avoid SEGV if core.cpus isn't set

Merge tag 'kbuild-fixes-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - Fix empty $(PYTHON) expansion.

 - Fix UML, which got broken by the attempt to suppress Clang warnings.

 - Fix warning message in modpost.

* tag 'kbuild-fixes-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  modpost: restore the warning message for missing symbol versions
  Revert "um: clang: Strip out -mno-global-merge from USER_CFLAGS"
  kbuild: Remove '-mno-global-merge'
  kbuild: fix empty ${PYTHON} in scripts/link-vmlinux.sh
  kconfig: remove stale comment about removed kconfig_print_symbol()

Pull MIPS fixes from Thomas Bogendoerfer:

 - build fix for gpio

 - fix crc32 build problems

 - check for failed memory allocations

* tag 'mips_5.18_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
  MIPS: crypto: Fix CRC32 code
  MIPS: rb532: move GPIOD definition into C-files
  MIPS: lantiq: check the return value of kzalloc()
  mips: sgi-ip22: add a check for the return of kzalloc()

Pull kvm fixes from Paolo Bonzini:

 - Only do MSR filtering for MSRs accessed by rdmsr/wrmsr

 - Documentation improvements

 - Prevent module exit until all VMs are freed

 - PMU Virtualization fixes

 - Fix for kvm_irq_delivery_to_apic_fast() NULL-pointer dereferences

 - Other miscellaneous bugfixes

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (42 commits)
  KVM: x86: fix sending PV IPI
  KVM: x86/mmu: do compare-and-exchange of gPTE via the user address
  KVM: x86: Remove redundant vm_entry_controls_clearbit() call
  KVM: x86: cleanup enter_rmode()
  KVM: x86: SVM: fix tsc scaling when the host doesn't support it
  kvm: x86: SVM: remove unused defines
  KVM: x86: SVM: move tsc ratio definitions to svm.h
  KVM: x86: SVM: fix avic spec based definitions again
  KVM: MIPS: remove reference to trap&emulate virtualization
  KVM: x86: document limitations of MSR filtering
  KVM: x86: Only do MSR filtering when access MSR by rdmsr/wrmsr
  KVM: x86/emulator: Emulate RDPID only if it is enabled in guest
  KVM: x86/pmu: Fix and isolate TSX-specific performance event logic
  KVM: x86: mmu: trace kvm_mmu_set_spte after the new SPTE was set
  KVM: x86/svm: Clear reserved bits written to PerfEvtSeln MSRs
  KVM: x86: Trace all APICv inhibit changes and capture overall status
  KVM: x86: Add wrappers for setting/clearing APICv inhibits
  KVM: x86: Make APICv inhibit reasons an enum and cleanup naming
  KVM: X86: Handle implicit supervisor access with SMAP
  KVM: X86: Rename variable smap to not_smap in permission_fault()
  ...

This log message was accidentally chopped off.

I was wondering why this happened, but checking the ML log, Mark
precisely followed my suggestion [1].

I just used "..." because I was too lazy to type the sentence fully.
Sorry for the confusion.

[1]: https://lore.kernel.org/all/CAK7LNAR6bXXk9-ZzZYpTqzFqdYbQsZHmiWspu27rtsFxvfRuVA@mail.gmail.com/

Fixes: 4a679593 ("kbuild: modpost: Explicitly warn about unprototyped symbols")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>