- 29 Jan, 2020 40 commits
-
-
Jose Abreu authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit 86051317 upstream. The 16KB RX Buffer must also be 16 byte aligned. Fix it. Fixes: 7ac6653a ("stmmac: Move the STMicroelectronics driver") Signed-off-by:
Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by:
Khalid Elmously <khalid.elmously@canonical.com>
-
Wen Yang authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit 6d9e8c65 upstream. Patch series "use div64_ul() instead of div_u64() if the divisor is unsigned long". We were first inspired by commit b0ab99e7 ("sched: Fix possible divide by zero in avg_atom () calculation"), then refer to the recently analyzed mm code, we found this suspicious place. 201 if (min) { 202 min *= this_bw; 203 do_div(min, tot_bw); 204 } And we also disassembled and confirmed it: /usr/src/debug/kernel-4.9.168-016.ali3000/linux-4.9.168-016.ali3000.alios7.x86_64/mm/page-writeback.c: 201 0xffffffff811c37da <__wb_calc_thresh+234>: xor %r10d,%r10d 0xffffffff811c37dd <__wb_calc_thresh+237>: test %rax,%rax 0xffffffff811c37e0 <__wb_calc_thresh+240>: je 0xffffffff811c3800 <__wb_calc_thresh+272> /usr/src/debug/kernel-4.9.168-016.ali3000/linux-4.9.168-016.ali3000.alios7.x86_64/mm/page-writeback.c: 202 0xffffffff811c37e2 <__wb_calc_thresh+242>: imul %r8,%rax /usr/src/debug/kernel-4.9.168-016.ali3000/linux-4.9.168-016.ali3000.alios7.x86_64/mm/page-writeback.c: 203 0xffffffff811c37e6 <__wb_calc_thresh+246>: mov %r9d,%r10d ---> truncates it to 32 bits here 0xffffffff811c37e9 <__wb_calc_thresh+249>: xor %edx,%edx 0xffffffff811c37eb <__wb_calc_thresh+251>: div %r10 0xffffffff811c37ee <__wb_calc_thresh+254>: imul %rbx,%rax 0xffffffff811c37f2 <__wb_calc_thresh+258>: shr $0x2,%rax 0xffffffff811c37f6 <__wb_calc_thresh+262>: mul %rcx 0xffffffff811c37f9 <__wb_calc_thresh+265>: shr $0x2,%rdx 0xffffffff811c37fd <__wb_calc_thresh+269>: mov %rdx,%r10 This series uses div64_ul() instead of div_u64() if the divisor is unsigned long, to avoid truncation to 32-bit on 64-bit platforms. This patch (of 3): The variables 'min' and 'max' are unsigned long and do_div truncates them to 32 bits, which means it can test non-zero and be truncated to zero for division. Fix this issue by using div64_ul() instead. Link: http://lkml.kernel.org/r/20200102081442.8273-2-wenyang@linux.alibaba.com Fixes: 693108a8 ("writeback: make bdi->min/max_ratio handling cgroup writeback aware") Signed-off-by:
Wen Yang <wenyang@linux.alibaba.com> Reviewed-by:
Andrew Morton <akpm@linux-foundation.org> Cc: Qian Cai <cai@lca.pw> Cc: Tejun Heo <tj@kernel.org> Cc: Jens Axboe <axboe@kernel.dk> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Ard Biesheuvel authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit 4911ee40 upstream. The EFI mixed mode entry code goes through the ordinary startup_32() routine before jumping into the kernel's EFI boot code in 64-bit mode. The 32-bit startup code must be entered with paging disabled, but this is not documented as a requirement for the EFI handover protocol, and so we should disable paging explicitly when entering the kernel from 32-bit EFI firmware. Signed-off-by:
Ard Biesheuvel <ardb@kernel.org> Cc: <stable@vger.kernel.org> Cc: Arvind Sankar <nivedita@alum.mit.edu> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-efi@vger.kernel.org Link: https://lkml.kernel.org/r/20191224132909.102540-4-ardb@kernel.orgSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Keiya Nobuta authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit 9c06ac4c upstream. If hub_activate() is called before D+ has stabilized after remote wakeup, the following situation might occur: __ ___________________ / \ / D+ __/ \__/ Hub _______________________________ | ^ ^ ^ | | | | Host _____v__|___|___________|______ | | | | | | | \-- Interrupt Transfer (*3) | | \-- ClearPortFeature (*2) | \-- GetPortStatus (*1) \-- Host detects remote wakeup - D+ goes high, Host starts running by remote wakeup - D+ is not stable, goes low - Host requests GetPortStatus at (*1) and gets the following hub status: - Current Connect Status bit is 0 - Connect Status Change bit is 1 - D+ stabilizes, goes high - Host requests ClearPortFeature and thus Connect Status Change bit is cleared at (*2) - After waiting 100 ms, Host starts the Interrupt Transfer at (*3) - Since the Connect Status Change bit is 0, Hub returns NAK. In this case, port_event() is not called in hub_event() and Host cannot recognize device. To solve this issue, flag change_bits even if only Connect Status Change bit is 1 when got in the first GetPortStatus. This issue occurs rarely because it only if D+ changes during a very short time between GetPortStatus and ClearPortFeature. However, it is fatal if it occurs in embedded system. Signed-off-by:
Keiya Nobuta <nobuta.keiya@fujitsu.com> Cc: stable <stable@vger.kernel.org> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20200109051448.28150-1-nobuta.keiya@fujitsu.comSigned-off-by:
-
Dan Carpenter authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit 28d76df1 upstream. Tom Hatskevich reported that we look up "iocp" then, in the called functions we do a second copy_from_user() and look it up again. The problem that could cause is: drivers/message/fusion/mptctl.c 674 /* All of these commands require an interrupt or 675 * are unknown/illegal. 676 */ 677 if ((ret = mptctl_syscall_down(iocp, nonblock)) != 0) ^^^^ We take this lock. 678 return ret; 679 680 if (cmd == MPTFWDOWNLOAD) 681 ret = mptctl_fw_download(arg); ^^^ Then the user memory changes and we look up "iocp" again but a different one so now we are holding the incorrect lock and have a race condition. 682 else if (cmd == MPTCOMMAND) 683 ret = mptctl_mpt_command(arg); The security impact of this bug is not as bad as it could have been because these operations are all privileged and root already has enormous destructive power. But it's still worth fixing. This patch passes the "iocp" pointer to the functions to avoid the second lookup. That deletes 100 lines of code from the driver so it's a nice clean up as well. Link: https://lore.kernel.org/r/20200114123414.GA7957@kadamReported-by:
Tom Hatskevich <tom2001tom.23@gmail.com> Reviewed-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Johan Hovold authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit 9715a43e upstream. Check for NULL port data in the modem- and line-status handlers to avoid dereferencing a NULL pointer in the unlikely case where a port device isn't bound to a driver (e.g. after an allocation failure on port probe). Note that the other (stubbed) event handlers qt2_process_xmit_empty() and qt2_process_flush() would need similar sanity checks in case they are ever implemented. Fixes: f7a33e60 ("USB: serial: add quatech2 usb to serial driver") Cc: stable <stable@vger.kernel.org> # 3.5 Reviewed-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Johan Hovold authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit 1568c58d upstream. The driver receives the active port number from the device, but never made sure that the port number was valid. This could lead to a NULL-pointer dereference or memory corruption in case a device sends data for an invalid port. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Cc: stable <stable@vger.kernel.org> Reviewed-by:
-
Johan Hovold authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit 4d5ef53f upstream. Check for NULL port data in reset_resume() to avoid dereferencing a NULL pointer in case the port device isn't bound to a driver (e.g. after a failed control request at port probe). Fixes: 1ded7ea4 ("USB: ch341 serial: fix port number changed after resume") Cc: stable <stable@vger.kernel.org> # 2.6.30 Reviewed-by:
-
Johan Hovold authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit fdb838ef upstream. USB-serial drivers must not be unbound from their ports before the corresponding USB driver is unbound from the parent interface so suppress the bind and unbind attributes. Unbinding a serial driver while it's port is open is a sure way to trigger a crash as any driver state is released on unbind while port hangup is handled on the parent USB interface level. Drivers for multiport devices where ports share a resource such as an interrupt endpoint also generally cannot handle individual ports going away. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Cc: stable <stable@vger.kernel.org> Reviewed-by:
-
Johan Hovold authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit 5e28055f upstream. The driver was issuing synchronous uninterruptible control requests without using a timeout. This could lead to the driver hanging on open() or tiocmset() due to a malfunctioning (or malicious) device until the device is physically disconnected. The USB upper limit of five seconds per request should be more than enough. Fixes: 309a0579 ("USB: opticon: add rts and cts support") Cc: stable <stable@vger.kernel.org> # 2.6.39 Cc: Martin Jansen <martin.jansen@opticon.com> Reviewed-by:
-
Jerónimo Borque authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit 260e41ac upstream. Add device-ids for the Motorola Solutions TETRA radios MTP3xxx series and MTP85xx series $ lsusb -vd 0cad: Bus 001 Device 009: ID 0cad:9015 Motorola CGISS TETRA PEI interface Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x0cad Motorola CGISS idProduct 0x9015 bcdDevice 24.16 iManufacturer 1 iProduct 2 iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 0x0037 bNumInterfaces 2 bConfigurationValue 1 iConfiguration 3 bmAttributes 0x80 (Bus Powered) MaxPower 500mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 0 bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 0 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 0 bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x02 EP 2 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 0 Bus 001 Device 010: ID 0cad:9013 Motorola CGISS TETRA PEI interface Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x0cad Motorola CGISS idProduct 0x9013 bcdDevice 24.16 iManufacturer 1 iProduct 2 iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 0x0037 bNumInterfaces 2 bConfigurationValue 1 iConfiguration 3 bmAttributes 0x80 (Bus Powered) MaxPower 500mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 0 bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 0 bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x02 EP 2 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Signed-off-by:
Jerónimo Borque <jeronimo@borque.com.ar> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Mikulas Patocka authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit ad6bf88a upstream. Logical block size has type unsigned short. That means that it can be at most 32768. However, there are architectures that can run with 64k pages (for example arm64) and on these architectures, it may be possible to create block devices with 64k block size. For exmaple (run this on an architecture with 64k pages): Mount will fail with this error because it tries to read the superblock using 2-sector access: device-mapper: writecache: I/O is not aligned, sector 2, size 1024, block size 65536 EXT4-fs (dm-0): unable to read superblock This patch changes the logical block size from unsigned short to unsigned int to avoid the overflow. Cc: stable@vger.kernel.org Reviewed-by:
Ming Lei <ming.lei@redhat.com> Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Jari Ruusu authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit f5ae2ea6 upstream. Intel Software Developer's Manual, volume 3, chapter 9.11.6 says: "Note that the microcode update must be aligned on a 16-byte boundary and the size of the microcode update must be 1-KByte granular" When early-load Intel microcode is loaded from initramfs, userspace tool 'iucode_tool' has already 16-byte aligned those microcode bits in that initramfs image. Image that was created something like this: iucode_tool --write-earlyfw=FOO.cpio microcode-files... However, when early-load Intel microcode is loaded from built-in firmware BLOB using CONFIG_EXTRA_FIRMWARE= kernel config option, that 16-byte alignment is not guaranteed. Fix this by forcing all built-in firmware BLOBs to 16-byte alignment. [ If we end up having other firmware with much bigger alignment requirements, we might need to introduce some method for the firmware to specify it, this is the minimal "just increase the alignment a bit to account for this one special case" patch - Linus ] Signed-off-by:
Jari Ruusu <jari.ruusu@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: Luis Chamberlain <mcgrof@kernel.org> Cc: stable@kernel.org Signed-off-by:
-
Takashi Iwai authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit 60adcfde upstream. snd_seq_info_timer_read() reads the information of the timer assigned for each queue, but it's done in a racy way which may lead to UAF as spotted by syzkaller. This patch applies the missing q->timer_mutex lock while accessing the timer object as well as a slight code change to adapt the standard coding style. Reported-by: syzbot+2b2ef983f973e5c40943@syzkaller.appspotmail.com Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200115203733.26530-1-tiwai@suse.deSigned-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Kai Li authored
BugLink: https://bugs.launchpad.net/bugs/1860681 [ Upstream commit 397eac17 ] If journal is dirty when mount, it will be replayed but jbd2 sb log tail cannot be updated to mark a new start because journal->j_flag has already been set with JBD2_ABORT first in journal_init_common. When a new transaction is committed, it will be recored in block 1 first(journal->j_tail is set to 1 in journal_reset). If emergency restart happens again before journal super block is updated unfortunately, the new recorded trans will not be replayed in the next mount. The following steps describe this procedure in detail. 1. mount and touch some files 2. these transactions are committed to journal area but not checkpointed 3. emergency restart 4. mount again and its journals are replayed 5. journal super block's first s_start is 1, but its s_seq is not updated 6. touch a new file and its trans is committed but not checkpointed 7. emergency restart again 8. mount and journal is dirty, but trans committed in 6 will not be replayed. This exception happens easily when this lun is used by only one node. If it is used by multi-nodes, other node will replay its journal and its journal super block will be updated after recovery like what this patch does. ocfs2_recover_node->ocfs2_replay_journal. The following jbd2 journal can be generated by touching a new file after journal is replayed, and seq 15 is the first valid commit, but first seq is 13 in journal super block. logdump: Block 0: Journal Superblock Seq: 0 Type: 4 (JBD2_SUPERBLOCK_V2) Blocksize: 4096 Total Blocks: 32768 First Block: 1 First Commit ID: 13 Start Log Blknum: 1 Error: 0 Feature Compat: 0 Feature Incompat: 2 block64 Feature RO compat: 0 Journal UUID: 4ED3822C54294467A4F8E87D2BA4BC36 FS Share Cnt: 1 Dynamic Superblk Blknum: 0 Per Txn Block Limit Journal: 0 Data: 0 Block 1: Journal Commit Block Seq: 14 Type: 2 (JBD2_COMMIT_BLOCK) Block 2: Journal Descriptor Seq: 15 Type: 1 (JBD2_DESCRIPTOR_BLOCK) No. Blocknum Flags 0. 587 none UUID: 00000000000000000000000000000000 1. 8257792 JBD2_FLAG_SAME_UUID 2. 619 JBD2_FLAG_SAME_UUID 3. 24772864 JBD2_FLAG_SAME_UUID 4. 8257802 JBD2_FLAG_SAME_UUID 5. 513 JBD2_FLAG_SAME_UUID JBD2_FLAG_LAST_TAG ... Block 7: Inode Inode: 8257802 Mode: 0640 Generation: 57157641 (0x3682809) FS Generation: 2839773110 (0xa9437fb6) CRC32: 00000000 ECC: 0000 Type: Regular Attr: 0x0 Flags: Valid Dynamic Features: (0x1) InlineData User: 0 (root) Group: 0 (root) Size: 7 Links: 1 Clusters: 0 ctime: 0x5de5d870 0x11104c61 -- Tue Dec 3 11:37:20.286280801 2019 atime: 0x5de5d870 0x113181a1 -- Tue Dec 3 11:37:20.288457121 2019 mtime: 0x5de5d870 0x11104c61 -- Tue Dec 3 11:37:20.286280801 2019 dtime: 0x0 -- Thu Jan 1 08:00:00 1970 ... Block 9: Journal Commit Block Seq: 15 Type: 2 (JBD2_COMMIT_BLOCK) The following is journal recovery log when recovering the upper jbd2 journal when mount again. syslog: ocfs2: File system on device (252,1) was not unmounted cleanly, recovering it. fs/jbd2/recovery.c:(do_one_pass, 449): Starting recovery pass 0 fs/jbd2/recovery.c:(do_one_pass, 449): Starting recovery pass 1 fs/jbd2/recovery.c:(do_one_pass, 449): Starting recovery pass 2 fs/jbd2/recovery.c:(jbd2_journal_recover, 278): JBD2: recovery, exit status 0, recovered transactions 13 to 13 Due to first commit seq 13 recorded in journal super is not consistent with the value recorded in block 1(seq is 14), journal recovery will be terminated before seq 15 even though it is an unbroken commit, inode 8257802 is a new file and it will be lost. Link: http://lkml.kernel.org/r/20191217020140.2197-1-li.kai4@h3c.comSigned-off-by:
Kai Li <li.kai4@h3c.com> Reviewed-by:
Joseph Qi <joseph.qi@linux.alibaba.com> Reviewed-by:
Changwei Ge <gechangwei@live.cn> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Signed-off-by:
Sasha Levin <sashal@kernel.org> Signed-off-by:
-
Nick Desaulniers authored
BugLink: https://bugs.launchpad.net/bugs/1860681 [ Upstream commit 63e80314 ] Clang cannot translate the string "r30" into a valid register yet. Link: https://github.com/ClangBuiltLinux/linux/issues/755 Link: http://lkml.kernel.org/r/20191028155722.23419-1-ndesaulniers@google.comSigned-off-by:
Nick Desaulniers <ndesaulniers@google.com> Suggested-by:
Sid Manning <sidneym@quicinc.com> Reviewed-by:
Brian Cain <bcain@codeaurora.org> Cc: Allison Randal <allison@lohutok.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Richard Fontana <rfontana@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Mathieu Desnoyers authored
BugLink: https://bugs.launchpad.net/bugs/1860681 [ Upstream commit af9cb29c ] As the rseq selftests can run for a long period of time, disable the timeout that the general selftests have. Signed-off-by:
Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Shuah Khan <skhan@linuxfoundation.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: "Paul E. McKenney" <paulmck@linux.ibm.com> Cc: Boqun Feng <boqun.feng@gmail.com> Cc: "H . Peter Anvin" <hpa@zytor.com> Cc: Paul Turner <pjt@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
Shuah Khan <skhan@linuxfoundation.org> Signed-off-by:
-
Kars de Jong authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit e34494c8 upstream. The driver was reading the wrong register as the 10-hour digit due to a misplaced ')'. It was in fact reading the 1-second digit register due to this bug. Also remove the use of a magic number for the hour mask and use the define for it which was already present. Fixes: 4f9b9bba ("rtc: Add an RTC driver for the Oki MSM6242") Tested-by:
Kars de Jong <jongk@linux-m68k.org> Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by:
-
Nathan Chancellor authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit 091c6e9c upstream. When building with Clang + -Wtautological-pointer-compare: drivers/net/wireless/realtek/rtlwifi/regd.c:389:33: warning: comparison of address of 'rtlpriv->regd' equal to a null pointer is always false [-Wtautological-pointer-compare] if (wiphy == NULL || &rtlpriv->regd == NULL) ~~~~~~~~~^~~~ ~~~~ 1 warning generated. The address of an array member is never NULL unless it is the first struct member so remove the unnecessary check. This was addressed in the staging version of the driver in commit f986978b ("Staging: rtlwifi: remove unnecessary NULL check"). While we are here, fix the following checkpatch warning: CHECK: Comparison to NULL could be written "!wiphy" 35: FILE: drivers/net/wireless/realtek/rtlwifi/regd.c:389: + if (wiphy == NULL) Fixes: 0c817338 ("rtl8192ce: Add new driver") Link:https://github.com/ClangBuiltLinux/linux/issues/750Signed-off-by:
Nathan Chancellor <natechancellor@gmail.com> Acked-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Mans Rullgard authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit fed8d8c7 upstream. The driver does the wrong thing when cs_change is set on a non-last xfer in a message. When cs_change is set, the driver deactivates the CS and leaves it off until a later xfer again has cs_change set whereas it should be briefly toggling CS off and on again. This patch brings the behaviour of the driver back in line with the documentation and common sense. The delay of 10 us is the same as is used by the default spi_transfer_one_message() function in spi.c. [gregory: rebased on for-5.5 from spi tree] Fixes: 8090d6d1 ("spi: atmel: Refactor spi-atmel to use SPI framework queue") Signed-off-by:
Mans Rullgard <mans@mansr.com> Acked-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by:
Gregory CLEMENT <gregory.clement@bootlin.com> Link: https://lore.kernel.org/r/20191018153504.4249-1-gregory.clement@bootlin.comSigned-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Seung-Woo Kim authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit 704c6c80 upstream. >From isp_video_release(), &isp->video_lock is held and subsequent vb2_fop_release() tries to lock vdev->lock which is same with the previous one. Replace vb2_fop_release() with _vb2_fop_release() to fix the recursive locking. Fixes: 1380f575 ("[media] videobuf2: Add missing lock held on vb2_fop_release") Signed-off-by:
Seung-Woo Kim <sw0312.kim@samsung.com> Reviewed-by:
Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by:
-
Peng Fan authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit 74887542 upstream. Per Documentation/DMA-API-HOWTO.txt, To unmap a scatterlist, just call: dma_unmap_sg(dev, sglist, nents, direction); .. note:: The 'nents' argument to the dma_unmap_sg call must be the _same_ one you passed into the dma_map_sg call, it should _NOT_ be the 'count' value _returned_ from the dma_map_sg call. However in the driver, priv->nent is directly assigned with value returned from dma_map_sg, and dma_unmap_sg use priv->nent for unmap, this breaks the API usage. So introduce a new entry orig_nent to remember 'nents'. Fixes: da3564ee ("pch_uart: add multi-scatter processing") Signed-off-by:
Peng Fan <peng.fan@nxp.com> Link: https://lore.kernel.org/r/1573623259-6339-1-git-send-email-peng.fan@nxp.comSigned-off-by:
-
Peng Fan authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit 596fd8df upstream. The dmaengine_prep_slave_sg needs to use sg count returned by dma_map_sg, not use sport->dma_tx_nents, because the return value of dma_map_sg is not always same with "nents". Fixes: b4cdc8f6 ("serial: imx: add DMA support for imx6q") Signed-off-by:
-
Arnd Bergmann authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit 9d7bf41f upstream. Unlike the normal SIOCOUTQ, SIOCOUTQNSD was never handled in compat mode. Add it to the common socket compat handler along with similar ones. Fixes: 2f4e1b39 ("tcp: ioctl type SIOCOUTQNSD returns amount of data not sent") Cc: Eric Dumazet <edumazet@google.com> Cc: netdev@vger.kernel.org Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Marian Mihailescu authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit e21be0d1 upstream. Save and restore top PLL related configuration registers for big (APLL) and LITTLE (KPLL) cores during suspend/resume cycle. So far, CPU clocks were reset to default values after suspend/resume cycle and performance after system resume was affected when performance governor has been selected. Fixes: 77342432 ("clk: samsung: exynos5420: add more registers to restore list") Signed-off-by:
Marian Mihailescu <mihailescu2m@gmail.com> Signed-off-by:
-
Alexander Usyskin authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit 73668309 upstream. mei client bus added the client protocol version to the device alias, but ABI documentation was not updated. Fixes: b26864ca (mei: bus: add client protocol version to the device alias) Signed-off-by:
Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by:
Tomas Winkler <tomas.winkler@intel.com> Link: https://lore.kernel.org/r/20191008005735.12707-1-tomas.winkler@intel.comSigned-off-by:
-
Alexandru Ardelean authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit 9b742763 upstream. This was found only after the whole thing with the inline functions, but the compiler actually found something. The value of the `bias` (in adis16480_get_calibbias()) should only be set if the read operation was successful. No actual known problem occurs as users of this function all ultimately check the return value. Hence probably not stable material. Fixes: 2f3abe6c ("iio:imu: Add support for the ADIS16480 and similar IMUs") Signed-off-by:
Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by:
-
Jian-Hong Pan authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit 176a7fca upstream. Some of ASUS laptops like UX431FL keyboard backlight cannot be set to brightness 0. According to ASUS' information, the brightness should be 0x80 ~ 0x83. This patch fixes it by following the logic. Fixes: e9809c0b ("asus-wmi: add keyboard backlight support") Signed-off-by:
Jian-Hong Pan <jian-hong@endlessm.com> Reviewed-by:
Daniel Drake <drake@endlessm.com> Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
Xiang Chen authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit 465f4eda upstream. If an attached disk with protection information enabled is reformatted to Type 0 the revalidation code does not clear the original protection type and subsequent accesses will keep setting RDPROTECT/WRPROTECT. Set the protection type to 0 if the disk reports PROT_EN=0 in READ CAPACITY(16). [mkp: commit desc] Fixes: fe542396 ("[SCSI] sd: Ensure we correctly disable devices with unknown protection type") Link: https://lore.kernel.org/r/1578532344-101668-1-git-send-email-chenxiang66@hisilicon.comSigned-off-by:
Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by:
-
James Bottomley authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit 529244bd upstream. Doing an add/remove/add on a SCSI device in an enclosure leads to an oops caused by poisoned values in the enclosure device list pointers. The reason is because we are keeping the enclosure device across the enclosed device add/remove/add but the current code is doing a device_add/device_del/device_add on it. This is the wrong thing to do in sysfs, so fix it by not doing a device_del on the enclosure device simply because of a hot remove of the drive in the slot. [mkp: added missing email addresses] Fixes: 43d8eb9c ("[SCSI] ses: add support for enclosure component hot removal") Link: https://lore.kernel.org/r/1578532892.3852.10.camel@HansenPartnership.comSigned-off-by:
James Bottomley <James.Bottomley@HansenPartnership.com> Reported-by:
Luo Jiaxing <luojiaxing@huawei.com> Tested-by:
John Garry <john.garry@huawei.com> Signed-off-by:
-
Bart Van Assche authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit e88982ad upstream. The code added by this patch is similar to the code that already exists in ibmvscsis_determine_resid(). This patch has been tested by running the following command: strace sg_raw -r 1k /dev/sdb 12 00 00 00 60 00 -o inquiry.bin |& grep resid= Link: https://lore.kernel.org/r/20191105214632.183302-1-bvanassche@acm.org Fixes: a42d985b ("ib_srpt: Initial SRP Target merge for v3.3-rc1") Signed-off-by:
Bart Van Assche <bvanassche@acm.org> Acked-by:
Honggang Li <honli@redhat.com> Signed-off-by:
Jason Gunthorpe <jgg@mellanox.com> Signed-off-by:
-
Nathan Chancellor authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit 7935799e upstream. Clang warns: ../fs/cifs/smb2file.c:70:3: warning: misleading indentation; statement is not part of the previous 'if' [-Wmisleading-indentation] if (oparms->tcon->use_resilient) { ^ ../fs/cifs/smb2file.c:66:2: note: previous statement is here if (rc) ^ 1 warning generated. This warning occurs because there is a space after the tab on this line. Remove it so that the indentation is consistent with the Linux kernel coding style and clang no longer warns. Fixes: 592fafe6 ("Add resilienthandles mount parm") Link: https://github.com/ClangBuiltLinux/linux/issues/826Signed-off-by:
Steve French <stfrench@microsoft.com> Signed-off-by:
-
Taehee Yoo authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit 3ed0a1d5 upstream. The supervision frame is L2 frame. When supervision frame is created, hsr module doesn't set network header. If tap routine is enabled, dev_queue_xmit_nit() is called and it checks network_header. If network_header pointer wasn't set(or invalid), it resets network_header and warns. In order to avoid unnecessary warning message, resetting network_header is needed. Test commands: ip netns add nst ip link add veth0 type veth peer name veth1 ip link add veth2 type veth peer name veth3 ip link set veth1 netns nst ip link set veth3 netns nst ip link set veth0 up ip link set veth2 up ip link add hsr0 type hsr slave1 veth0 slave2 veth2 ip a a 192.168.100.1/24 dev hsr0 ip link set hsr0 up ip netns exec nst ip link set veth1 up ip netns exec nst ip link set veth3 up ip netns exec nst ip link add hsr1 type hsr slave1 veth1 slave2 veth3 ip netns exec nst ip a a 192.168.100.2/24 dev hsr1 ip netns exec nst ip link set hsr1 up tcpdump -nei veth0 Splat looks like: [ 175.852292][ C3] protocol 88fb is buggy, dev veth0 Fixes: f421436a ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)") Signed-off-by:
Taehee Yoo <ap420073@gmail.com> Signed-off-by:
-
Geert Uytterhoeven authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit d935bd50 upstream. When a GPIO offset in a lookup table is out-of-range, the printed error message (1) does not include the actual out-of-range value, and (2) contains an off-by-one error in the upper bound. Avoid user confusion by also printing the actual GPIO offset, and correcting the upper bound of the range. While at it, use "%u" for unsigned int. Sample impact: -requested GPIO 0 is out of range [0..32] for chip e6052000.gpio +requested GPIO 0 (45) is out of range [0..31] for chip e6052000.gpio Fixes: 2a3cf6a3 ("gpiolib: return -ENOENT if no GPIO mapping exists") Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20191127095919.4214-1-geert+renesas@glider.beSigned-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Jon Derrick authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit 7d4e6ccd upstream. This adds the missing teardown step that removes the device link from the group when the device addition fails. Signed-off-by:
Jon Derrick <jonathan.derrick@intel.com> Fixes: 797a8b4d ("iommu: Handle default domain attach failure") Reviewed-by:
Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by:
Joerg Roedel <jroedel@suse.de> Signed-off-by:
-
Ran Bi authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit 653997ee upstream. Alarm registers high byte was reserved for other functions. This add mask in alarm registers operation functions. This also fix error condition in interrupt handler. Fixes: fc297911 ("rtc: mediatek: Add MT6397 RTC driver") Signed-off-by:
Ran Bi <ran.bi@mediatek.com> Signed-off-by:
Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com> Link: https://lore.kernel.org/r/1576057435-3561-6-git-send-email-hsin-hsiung.wang@mediatek.comSigned-off-by:
-
Theodore Ts'o authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit 4ea99936 upstream. It's possible to specify a non-zero s_want_extra_isize via debugging option, and this can cause bad things(tm) to happen when using a file system with an inode size of 128 bytes. Add better checking when the file system is mounted, as well as when we are actually doing the trying to do the inode expansion. Link: https://lore.kernel.org/r/20191110121510.GH23325@mit.edu Reported-by: syzbot+f8d6f8386ceacdbfff57@syzkaller.appspotmail.com Reported-by: syzbot+33d7ea72e47de3bdf4e1@syzkaller.appspotmail.com Reported-by: syzbot+44b6763edfc17144296f@syzkaller.appspotmail.com Signed-off-by:
Theodore Ts'o <tytso@mit.edu> [bwh: Backported to 4.4: adjust context] Signed-off-by:
Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by:
-
Barret Rhoden authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit 7bc04c5c upstream. When remounting with debug_want_extra_isize, we were not performing the same checks that we do during a normal mount. That allowed us to set a value for s_want_extra_isize that reached outside the s_inode_size. Fixes: e2b911c5 ("ext4: clean up feature test macros with predicate functions") Reported-by: syzbot+f584efa0ac7213c226b7@syzkaller.appspotmail.com Reviewed-by:
Jan Kara <jack@suse.cz> Signed-off-by:
Barret Rhoden <brho@google.com> Signed-off-by:
-
Navid Emamdoost authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit 6f3ef5c2 upstream. In the implementation of i2400m_op_rfkill_sw_toggle() the allocated buffer for cmd should be released before returning. The documentation for i2400m_msg_to_dev() says when it returns the buffer can be reused. Meaning cmd should be released in either case. Move kfree(cmd) before return to be reached by all execution paths. Fixes: 2507e6ab ("wimax: i2400: fix memory leak") Signed-off-by:
Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by:
-
Navid Emamdoost authored
BugLink: https://bugs.launchpad.net/bugs/1860681 commit 2507e6ab upstream. In i2400m_op_rfkill_sw_toggle cmd buffer should be released along with skb response. Signed-off-by:
-
