- 04 Mar, 2011 36 commits
-
-
Stanislaw Gruszka authored
Usually H/W generate statistics notify once per about 100ms, but sometimes we can receive notify in shorter time, even 2 ms. This can be problem for plcp health and ack health checking. I.e. with 2 plcp errors happens randomly in 2 ms duration, we exceed plcp delta threshold equal to 100 (2*100/2). Also checking ack's in short time, can results not necessary false positive and firmware reset, for example when channel is noised and we do not receive ACKs frames or when remote device does not send ACKs at the moment. Patch change code to do statistic check and possible recovery only if 99ms elapsed from last check. Forced delay should assure we have good statistic data to estimate hardware state. Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Acked-by:
Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Stanislaw Gruszka authored
Make iwl_good_plcp_health code easiest to read. Signed-off-by:
-
Stanislaw Gruszka authored
Put generic rx_handlers (except iwlagn_rx_reply_compressed_ba) to iwl-rx.c . Make functions static and change prefix from iwlagn_ to iwl_ . Beautify iwl_setup_rx_handlers and do some other minor coding style changes. Signed-off-by:
-
Helmut Schaa authored
mac80211 does the same afterwards anyway. Hence, just drop this redundant code. Signed-off-by:
Helmut Schaa <helmut.schaa@googlemail.com> Acked-by:
Felix Fietkau <nbd@openwrt.org> Signed-off-by:
-
Ben Greear authored
No use printing addresses of pointers, just print the pointers themselves. Signed-off-by:
Ben Greear <greearb@candelatech.com> Signed-off-by:
-
Gertjan van Wingerde authored
Now that all accesses to the data_queue structures is done via the specialized rt2x00queue_get_tx_queue function or via direct accesses, there is no need for the rt2x00queue_get_queue function anymore, so remove it. Signed-off-by:
Gertjan van Wingerde <gwingerde@gmail.com> Acked-by:
Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by:
-
Gertjan van Wingerde authored
In the spirit of optimizing the code to get the queue structure of TX queues, also optimize the code to get beacon queues. We can simply use the bcn queue field of the rt2x00_dev structure instead of using the rt2x00queue_get_queue function. Signed-off-by:
-
Gertjan van Wingerde authored
The ATIM queue is considered to be a TX queue by the drivers that support the queue. Therefore include support for the ATIM queue to the rt2x00queue_get_tx_queue function so that the drivers that support the ATIM queue can also use that function. Add the support in such a way that drivers that do not support the ATIM queue are not penalized in their efficiency. Signed-off-by:
-
Gertjan van Wingerde authored
Current code for the atim queue is strange, as it is considered in the rt2x00_dev structure as a second beacon queue. Normalize this by letting the atim queue have its own struct data_queue pointer in the rt2x00_dev structure. Signed-off-by:
-
Helmut Schaa authored
We don't use interrupt threads anymore. Fix the comment. Signed-off-by:
-
Helmut Schaa authored
The PCI device irqmask is locked by a spin_lock. Currently spin_lock_irqsave is used everywhere. To reduce the locking overhead replace spin_lock_irqsave in hard irq context with spin_lock and in soft irq context with spin_lock_irq. Signed-off-by:
-
Helmut Schaa authored
Signed-off-by:
-
Helmut Schaa authored
When setting up multiple BSSIDs in AP mode on an rt2800pci device we previously used the STAs AID to select an appropriate key slot. But since the AID is per VIF we can end up with two STAs having the same AID and thus using the same key index. This resulted in one STA overwriting the key information of another STA. Fix this by simply searching for the next unused entry in the pairwise key table. Also bring the key table init in sync with deleting keys by initializing the key table entries to 0 instead of 1. Signed-off-by:
-
Helmut Schaa authored
This makes the code less error-prone. Acked-by:
-
Helmut Schaa authored
ieee80211_get_tx_rate is not valid for HT rates. Hence, restructure the TX desciptor creation to be aware of MCS rates. The generic TX desciptor creation now cares about the rate_mode (CCK, OFDM, MCS, GF). As a result, ieee80211_get_tx_rate gets only called for legacy rates. Acked-by:
-
Helmut Schaa authored
"ifs" is only used by no-HT devices. Move it into the plcp substruct and fill in the value only for no-HT devices. Signed-off-by:
-
Ivo van Doorn authored
Some fields only need to be u8 and for ifs and txop we can use the already available enums. Acked-by:
-
Helmut Schaa authored
HT and no-HT rt2x00 devices use a partly different TX descriptor. Optimize the tx desciptor memory layout by putting the PLCP and HT substructs into a union and introduce a new driver flag to decide which TX desciptor format is used by the device. This saves us the expensive PLCP calculation fOr HT devices and the HT descriptor setup on no-HT devices. Acked-by:
-
Helmut Schaa authored
Newer devices like rt2800* own a hardware sequence counter and thus don't need to use a software sequence counter at all. Add a new driver flag to shortcut the software sequence number generation on devices that don't need it. rt61pci, rt73usb and rt2800* seem to make use of a hw sequence counter while rt2400pci and rt2500* need to do it in software. Signed-off-by:
-
Helmut Schaa authored
rt2x00queue_write_tx_frame is unlikely to fail. Tell the compiler. Signed-off-by:
-
Helmut Schaa authored
This special case shouldn't happen very often. Only if a frame that is not intended to be aggregated ends up in an AMPDU _and_ was intended to be sent at a different MCS rate as the aggregate. Hence, using unlikely is justified. Signed-off-by:
-
Helmut Schaa authored
Since tx_info->control.vif was already accessed before it cant't be NULL here. Signed-off-by:
-
Helmut Schaa authored
These conditions are unlikely to happen, tell the compiler. Signed-off-by:
-
Helmut Schaa authored
In some cases (tx path for example) we don't need to check for non-tx queues in rt2x00queue_get_queue. Hence, introduce a new method rt2x00queue_get_tx_queue that is only valid for tx queues and use it in places where only tx queues are valid. Furthermore, this new method is quite short and as such can be inlined to avoid the function call overhead. This only converts the txdone functions of drivers that don't use an ATIM queue and the generic tx path. Signed-off-by:
-
Gabor Juhos authored
The rt2800 specific code contains a lots of whitespace damage caused by the commit 'rt2x00: Add support for RT5390 chip'. This patch fixes those whitespace errors. Signed-off-by:
Gabor Juhos <juhosg@openwrt.org> Acked-by:
-
Rafał Miłecki authored
Signed-off-by:
Rafał Miłecki <zajec5@gmail.com> Signed-off-by:
-
Rafał Miłecki authored
Signed-off-by:
-
Rafał Miłecki authored
Signed-off-by:
-
Michael Buesch authored
Make CONFIG_AVERAGE selectable for out-of-tree users such as compat-wireless. Signed-off-by:
Michael Buesch <mb@bu3sch.de> Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Signed-off-by:
Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by:
-
Vasanthakumar Thiagarajan authored
/<debugfs_root>/ieee80211/phyX/ath9k/regdump is the interface to dump the registers. Signed-off-by:
-
Larry Finger authored
The driver for the RTL8187L chips returns IEEE80211_TX_STAT_ACK for all packets, even if the maximum number of retries was exhausted. In addition it fails to setup max_rates in the ieee80211_hw struct, This behavior may be responsible for the problems noted in Bug 14168. As the bug is very old, testers have not been found, and I do not have the case where the indicated signal is less than -70 dBm. Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Acked-by:
Hin-Tak Leung <htl10@users.sourceforge.net> Cc: Stable <stable@kernel.org> Signed-off-by:
-
John W. Linville authored
ERROR: "usb_unanchor_urb" [drivers/net/wireless/rtlwifi/rtlwifi.ko] undefined! ERROR: "usb_control_msg" [drivers/net/wireless/rtlwifi/rtlwifi.ko] undefined! ERROR: "usb_submit_urb" [drivers/net/wireless/rtlwifi/rtlwifi.ko] undefined! ERROR: "usb_get_dev" [drivers/net/wireless/rtlwifi/rtlwifi.ko] undefined! ERROR: "usb_kill_anchored_urbs" [drivers/net/wireless/rtlwifi/rtlwifi.ko] undefined! ERROR: "usb_put_dev" [drivers/net/wireless/rtlwifi/rtlwifi.ko] undefined! ERROR: "usb_free_urb" [drivers/net/wireless/rtlwifi/rtlwifi.ko] undefined! ERROR: "usb_anchor_urb" [drivers/net/wireless/rtlwifi/rtlwifi.ko] undefined! ERROR: "usb_alloc_urb" [drivers/net/wireless/rtlwifi/rtlwifi.ko] undefined! make[2]: *** [__modpost] Error 1 make[1]: *** [modules] Error 2 make: *** [sub-make] Error 2 The USB-part of rtlwifi should depend on CONFIG_USB. This also corrects the existing check for CONFIG_PCI to build pci.o. Reported-by:
Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
-
John W. Linville authored
Merge branch 'wireless-next-2.6' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-2.6
-
-
-
- 03 Mar, 2011 4 commits
-
-
Fry, Donald H authored
The temperature reported by 'cat /sys/class/net/wlan?/device/temperature' is incorrect for devices with BT capability. Report the value from the correct statistics structure. Tested with 130, 100, 6205 and 5300. Signed-off-by:
Don Fry <donald.h.fry@intel.com> Signed-off-by:
-
Helmut Schaa authored
Set the gf_protection bit when calling ACX_HT_BSS_OPERATION according to the GF bit passed by mac80211 in ht_operation_mode. [Added a proper commit message -- Luca] Signed-off-by:
Luciano Coelho <coelho@ti.com>
-
Arik Nemtsov authored
Commands are sometimes sent to FW on scan completion. Make sure the chip is awake to receive them. Sending commands while the chip is in ELP can cause SDIO read errors and/or crash the FW. Signed-off-by:
Arik Nemtsov <arik@wizery.com> Signed-off-by:
Ido Yariv <ido@wizery.com> Signed-off-by:
-
Ido Yariv authored
Tests have shown that the requested number of memory blocks is sub-optimal. Slightly modify the requested number of memory blocks for TX. Signed-off-by:
-
