Add proper namespacing to the variable.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5171/

RT2880 has a different location for the early serial port.
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5170/

Add a few missing defines that are needed to make memory detection work on the
RT5350.
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5169/

Trivial patch that adds a comment that makes the code more readable.
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5168/

Add a few missing clocks.
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5167/

Add a few missing defines that are needed to make USB and clock detection work
on the RT3352.
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5166/

The Ralink IRQ code was not handling the PCI IRQ yet. Add this functionaility
to make PCI work on rt3883.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5165/

Previously this functionality was only available to users of the mips_machine
api. Moving the code to prom.c allows us to also add a OF wrapper.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5164/

Current GPIO chip implementation in octeon-irq is still broken, even after upstream
commit 87161ccd (MIPS: Octeon: Fix broken interrupt
controller code). It works for GPIO IRQs that have reset-default configuration, but
not for edge-triggered ones.

The problem is in octeon_irq_gpio_map_common(), which passes modified "hw" variable
(which has range of possible values 16..31) as "gpio_line" parameter to
octeon_irq_set_ciu_mapping(), which saves it in private data of the IRQ chip. Later,
neither octeon_irq_gpio_setup() is able to re-configure GPIOs (cvmx_write_csr() is
writing to non-existent CVMX_GPIO_BIT_CFGX), nor octeon_irq_ciu_gpio_ack() is able
to acknowledge such IRQ, because "mask" is incorrect.

Fix is trivial and has been tested on Cavium Octeon II -based board, including
both level-triggered and edge-triggered GPIO IRQs.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin.ext@nsn.com>
Cc: David Daney <david.daney@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Patchwork: http://patchwork.linux-mips.org/patch/4980/Acked-by: John Crispin <blogic@openwrt.org>

Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
Signed-off-by: Silviu-Mihai Popescu <silviupopescu1990@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/4986/Acked-by: John Crispin <blogic@openwrt.org>

The operations on the bitmap pointers are protected by "memory"
clobbering raw_local_irq_{save,restore}(), so there is no need for
volatile here.  By removing the volatile we get better code generation
out of the compiler.
Signed-off-by: David Daney <david.daney@cavium.com>
Patchwork: http://patchwork.linux-mips.org/patch/4966/Acked-by: John Crispin <blogic@openwrt.org>

Currently, init_new_context() only for each online CPU, this may cause
memory corruption when CPU hotplug and fork() happens at the same time.
To avoid this, we make init_new_context() cover each possible CPU.

Scenario:
1, CPU#1 is being offline;
2, On CPU#0, do_fork() call dup_mm() and copy a mm_struct to the child;
3, On CPU#0, dup_mm() call init_new_context(), since CPU#1 is offline
   and init_new_context() only covers the online CPUs, child has the
   same asid as its parent on CPU#1 (however, child's asid should be 0);
4, CPU#1 is being online;
5, Now, if both parent and child run on CPU#1, memory corruption (e.g.
   segfault, bus error, etc.) will occur.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Acked-by: David Daney <david.daney@cavium.com>
Patchwork: http://patchwork.linux-mips.org/patch/4995/Acked-by: John Crispin <blogic@openwrt.org>

This and the next patch resolve memory corruption problems while CPU
hotplug. Without these patches, memory corruption can triggered easily
as below:

On a quad-core MIPS platform, use "spawn" of UnixBench-5.1.3 (http://
code.google.com/p/byte-unixbench/) and a CPU hotplug script like this
(hotplug.sh):
while true; do
echo 0 >/sys/devices/system/cpu/cpu1/online
echo 0 >/sys/devices/system/cpu/cpu2/online
echo 0 >/sys/devices/system/cpu/cpu3/online
sleep 1
echo 1 >/sys/devices/system/cpu/cpu1/online
echo 1 >/sys/devices/system/cpu/cpu2/online
echo 1 >/sys/devices/system/cpu/cpu3/online
sleep 1
done

Run "hotplug.sh" and then run "spawn 10000", spawn will get segfault
after a few minutes.

This patch:
Currently, clear_page()/copy_page() are generated by Micro-assembler
dynamically. But they are unavailable until uasm_resolve_relocs() has
finished because jump labels are illegal before that. Since these
functions are shared by every CPU, we only call build_clear_page()/
build_copy_page() only once at boot time. Without this patch, programs
will get random memory corruption (segmentation fault, bus error, etc.)
while CPU Hotplug (e.g. one CPU is using clear_page() while another is
generating it in cpu_cache_init()).

For similar reasons we modify build_tlb_refill_handler()'s invocation.

V2:
1, Rework the code to make CPU#0 can be online/offline.
2, Introduce cpu_has_local_ebase feature since some types of MIPS CPU
   need a per-CPU tlb_refill_handler().
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongbing Hu <huhb@lemote.com>
Acked-by: David Daney <david.daney@cavium.com>
Patchwork: http://patchwork.linux-mips.org/patch/4994/Acked-by: John Crispin <blogic@openwrt.org>

The Kconfig symbol MIPS_DISABLE_OBSOLETE_IDE was added in v2.6.10. It
has never been used. Let's remove it.

The symbol was originally introduced by the following commit

commit 2bfa662b64a7ee593f3039c1d3fd81a7766a63cd
Author: Pete Popov <ppopov@embeddedalley.com>
Date:   Tue Oct 12 06:24:19 2004 +0000
    - Db1550 bug fixes
    - updated defconfig
    - updated Kconfig to use DMA_COHERENT since new silicon is coherent
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Patchwork: http://patchwork.linux-mips.org/patch/5064/Acked-by: John Crispin <blogic@openwrt.org>

The Kconfig symbol MIPS_BOARDS_GEN is unused since v2.6.27. It should
now be removed.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Patchwork: http://patchwork.linux-mips.org/patch/5063/Acked-by: John Crispin <blogic@openwrt.org>

The support for PB1100, PB1500, and PB1550 got merged into the code for
DB1000 and DB1550 code in v3.7. When that was done the three related
Kconfig symbols were dropped. But not all related Kconfig macros were
removed. Do so now.

Note that the PB1100 code in the Au1100 LCD driver is removed entirely
and not converted to use its current Kconfig macro. That is done because
the macros it uses (PB1100_G_CONTROL, PB1100_G_CONTROL_BL, and
PB1100_G_CONTROL_VDD) are never defined. Actually only one of these was
ever defined (PB1100_G_CONTROL) but that define was removed in v2.6.34.
So, as far as I can tell, this code could have never compiled.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Patchwork: http://patchwork.linux-mips.org/patch/5040/Acked-by: John Crispin <blogic@openwrt.org>

The commit c783390a [MIPS: oprofile:
Support for XLR/XLS processors] causes a compilation failure when
oprofile is enabled and SMP is not configured.

arch/mips/oprofile/op_model_mipsxx.c: In function 'mipsxx_cpu_setup':
arch/mips/oprofile/op_model_mipsxx.c:181:2: error: implicit declaration of function 'cpu_logical_map'

To fix this, update oprofile_skip_cpu to not call cpu_logical_map when
CONFIG_SMP is not defined.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5037/Acked-by: John Crispin <blogic@openwrt.org>

The definitions are not used anywhere else, and merging it will
make adding the new USB definitions for XLPII series easier.
While there, cleanup some whitespace in usb-init.c. There is no
change to logic due to this commit.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5027/Acked-by: John Crispin <blogic@openwrt.org>

This enables us to have a default device tree per SoC family to be built
into the kernel. The default device tree for XLP3xx has been added as part
of this change. Later this can be used to provide support default boards
for XLP2xx and XLP9xx SoCs.

Kconfig options are provided for each default device tree so that just the
needed ones can be selected to be built into the kernel.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5023/Acked-by: John Crispin <blogic@openwrt.org>

Remove unused functions and redundant comments from
arch/mips/include/asm/netlogic/haldefs.h
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5029/Acked-by: John Crispin <blogic@openwrt.org>

Update asm/netlogic/haldefs.h to extend register access functions
nlm_{read,write}_reg64() for 32-bit compilation. When compiled for 32-bit
the functions will read 64 IO registers with interrupts disabled.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5026/Acked-by: John Crispin <blogic@openwrt.org>

The index for a device interrupt in the PIC interrupt routing table
changes for different chips in the XLP family.  Avoid using the fixed
entries and derive the index value from the SoC device header.

Add workarounds for some devices which do not report the IRT index
correctly.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5025/Acked-by: John Crispin <blogic@openwrt.org>

Use standard function to print cpumask. Also fixup the name of the
variable used and make it static.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5024/Acked-by: John Crispin <blogic@openwrt.org>

Remove the definitions of {read,write}_c0_{eirr,eimr}. These functions
are now unused after the PIC and IRQ code has been updated to use
optimized EIMR/EIRR functions which work on both 32-bit and 64-bit.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5021/Acked-by: John Crispin <blogic@openwrt.org>

Remove the irq save/restore from write_c0_eimr(), as it is always called
with interrupts off.

This allows us to remove workaround in write_c0_eimr() to fix up the
flags used by local_irq_save. This fixup worked on XLR, but will break
when 32-bit support is added to r2 cpus like XLP.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5022/Acked-by: John Crispin <blogic@openwrt.org>

All the header file does is provide the internal structure of clk,
which shouldn't be used by anyone except clk.c itself anyway.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patchwork: http://patchwork.linux-mips.org/patch/5055/Acked-by: John Crispin <blogic@openwrt.org>

BCM6362 support booting from SPI flash and NAND.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5012/Acked-by: John Crispin <blogic@openwrt.org>

The PCIe controller is almost the same as the BCM6328 one, with only
the SERDES register being at a different location.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5011/Acked-by: John Crispin <blogic@openwrt.org>

The SPI controller shares the same register layout as the 6358 one.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5010/Acked-by: John Crispin <blogic@openwrt.org>

Add basic support for detecting and booting the BCM6362.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5009/Acked-by: John Crispin <blogic@openwrt.org>

Instead of trying to use a correlation of cpu prid and chip id and
hoping they will always be unique, use the cpu prid to determine the
chip id register location and just read out the chip id.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5008/Acked-by: John Crispin <blogic@openwrt.org>

The REVID is only 8 bit wide.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5007/Acked-by: John Crispin <blogic@openwrt.org>

BCM6338 and BCM6348, and BCM6358 and everything after that share the
same register layout. To not have to redefine them for each new chip
and keep the code size small, only use the definitions for the first
chip with the certain layout.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5006/Acked-by: John Crispin <blogic@openwrt.org>

Pull x86 fixes from Ingo Molnar:
 "Misc fixes"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm: Flush lazy MMU when DEBUG_PAGEALLOC is set
  x86/mm/cpa/selftest: Fix false positive in CPA self test
  x86/mm/cpa: Convert noop to functional fix
  x86, mm: Patch out arch_flush_lazy_mmu_mode() when running on bare metal
  x86, mm, paravirt: Fix vmalloc_fault oops during lazy MMU updates

Pull scheduler fixes from Ingo Molnar:
 "Misc fixlets"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/cputime: Fix accounting on multi-threaded processes
  sched/debug: Fix sd->*_idx limit range avoiding overflow
  sched_clock: Prevent 64bit inatomicity on 32bit systems
  sched: Convert BUG_ON()s in try_to_wake_up_local() to WARN_ON_ONCE()s

Pull perf fixes from Ingo Molnar:
 "Misc fixlets"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: Fix error return code
  ftrace: Fix strncpy() use, use strlcpy() instead of strncpy()
  perf: Fix strncpy() use, use strlcpy() instead of strncpy()
  perf: Fix strncpy() use, always make sure it's NUL terminated
  perf: Fix ring_buffer perf_output_space() boundary calculation
  perf/x86: Fix uninitialized pt_regs in intel_pmu_drain_bts_buffer()

Pull drm fixes from Dave Airlie:
 "One fix for a hotplug locking regressions, and one fix for an oops if
  you unplug the monitor at an inopportune moment on the udl device."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/fb-helper: Fix locking in drm_fb_helper_hotplug_event
  udl: handle EDID failure properly.

Pull m68knommu fix from Greg Ungerer:
 "This contains only a single compilation fix for ColdFire m68k targets
  that use local non-GPIOLIB support."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
  m68k: define a local gpio_request_one() function

Pull watchdog fix from Wim Van Sebroeck:
 "It will fix compile errors for the at91rm9200_wdt driver"

* git://www.linux-watchdog.org/linux-watchdog:
  watchdog: Revert the AT91RM9200_WATCHDOG dependency