- 20 Dec, 2013 3 commits
-
-
Lalit Chandivade authored
The statistics include MAC, TCP/IP & iSCSI statistics. Signed-off-by:
Lalit Chandivade <lalit.chandivade@qlogic.com> Signed-off-by:
Vikas Chaudhary <vikas.chaudhary@qlogic.com> Reviewed-by:
Mike Christie <michaelc@cs.wisc.edu> Signed-off-by:
James Bottomley <JBottomley@Parallels.com>
-
Lalit Chandivade authored
Add transport_iscsi hooks to get aggregate host statistics. The statistics include MAC, TCP/IP & iSCSI statistics. Signed-off-by:
-
Vikas Chaudhary authored
Added support for Diagnostics MBOX command via BSG Vendor HST_VENDOR interface. This command provides various tests for validating hardware functionality. Signed-off-by:
-
- 19 Dec, 2013 37 commits
-
-
Vijaya Mohan Guvva authored
Patch includes changes to upgrade bfa driver version to 3.2.23.0 and use firmware version 3.2.3.0 Signed-off-by:
Vijaya Mohan Guvva <vmohan@brocade.com> Signed-off-by:
-
Vijaya Mohan Guvva authored
As per the FCP specs, the timeout for issuing ABTS is 20 sec; not 21 sec. Hence setting the TOV to 20 sec. Signed-off-by:
-
Vijaya Mohan Guvva authored
Observed Auto mode in the HBA side while doing manual D-Port test on the switch side. Mode is not passed to BFA from firmware when the test is triggered by switch side. BFA just blindly using Auto mode. Signed-off-by:
-
Vijaya Mohan Guvva authored
This patch set fixes the issue of brocade management utility hang (bcu/HCM) when faa attributes are queried from multiple application threads. Hang was due to race between the threads and completion handler corruption. Signed-off-by:
-
Vijaya Mohan Guvva authored
In direct attach mode, if port features like QoS/Trunk/FEC/CR are enabled, driver can receive PLOGI from the target before firmware notifies lport online to the driver. In case the lport is not yet online and a PLOGI is received, send a reject to the peer port, instead of dropping it on the floor. Signed-off-by:
-
Vijaya Mohan Guvva authored
This patch addresses the issue of port not being registered with SCSI layer on bfa or firmware initialization failure and subsequently failure in collecting driver traces for debugging port init failures. Also it has minor changes related to bfad state machine clean up. Signed-off-by:
-
Vijaya Mohan Guvva authored
This patch includes change to enable firmware patch simplication feature. This feature is targeted to address the requirement to have independent patch release for firmware. Prior to 3.2.3, releasing a patch fix for firmware requires changes to bfa, to use new firmware images. But with these changes, if the new firmware is flashed on to the HBA with brocade adapter management utilites, driver uses the new firmware after checking the patch release byte in the firmware version. Signed-off-by:
-
Geyslan G. Bem authored
There are two memory leaks in cases 'ISCSI_NET_PARAM_VLAN_ID' and 'ISCSI_NET_PARAM_VLAN_PRIORITY' and also a potential junk pointer free if mgmt_get_if_info() returns error because if_info will be unset and it is stack allocated. Signed-off-by:
Geyslan G. Bem <geyslan@gmail.com> Cc: Jayamohan Kallickal <jayamohan.kallickal@emulex.com> Signed-off-by:
-
wenxiong@linux.vnet.ibm.com authored
Signed-off-by:
Wen Xiong <wenxiong@linux.vnet.ibm.com> Acked-by:
Brian King <brking@linux.vnet.ibm.com> Signed-off-by:
-
Mike Miller authored
Remove PCI ID for the never shipped P822se. Signed-off-by:
Mike Miller <mike.miller@hp.com> Signed-off-by:
-
Saurav Kashyap authored
Signed-off-by:
Giridhar Malavali <giridhar.malavali@qlogic.com> Signed-off-by:
Saurav Kashyap <saurav.kashyap@qlogic.com> Signed-off-by:
-
Geert Uytterhoeven authored
do_div() is meant for divisions of 64-bit number by 32-bit numbers. Passing 64-bit divisor types caused issues in the past on 32-bit platforms, cfr. commit ea077b1b ("m68k: Truncate base in do_div()"). As scsi_device.sector_size is unsigned (int), factor should be unsigned int, too. Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
-
Felipe Pena authored
On lpfc_debugfs_initialize function the dumpHostSlim member setup happens when 'phba->sli_rev < LPFC_SLI_REV4' is true, however when it is false NULL has been assigned to debug_dumpHBASlim instead of debug_dumpHostSlim. Signed-off-by:
Felipe Pena <felipensp@gmail.com> Acked-by:
James Smart <james.smart@emulex.com> Signed-off-by:
-
Ben Collins authored
The assumption that sizeof(long) >= sizeof(resource_size_t) can lead to truncation of the PCI resource address, meaning this driver didn't work on 32-bit systems with 64-bit PCI adressing ranges. Signed-off-by:
Ben Collins <ben.c@servergy.com> Acked-by:
Sumit Saxena <sumit.saxena@lsi.com> Signed-off-by:
-
Hannes Reinecke authored
The documentation has gone out-of-sync, so update it to the current status. Signed-off-by:
Hannes Reinecke <hare@suse.de> Signed-off-by:
-
Ren Mingxin authored
The former minimum valid value of 'eh_deadline' is 1s, which means the earliest occasion to shorten EH is 1 second later since a command is failed or timed out. But if we want to skip EH steps ASAP, we have to wait until the first EH step is finished. If the duration of the first EH step is long, this waiting time is excruciating. So, it is necessary to accept 0 as the minimum valid value for 'eh_deadline'. According to my test, with Hannes' patchset 'New EH command timeout handler' as well, the minimum IO time is improved from 73s (eh_deadline = 1) to 43s(eh_deadline = 0) when commands are timed out by disabling RSCN and target port. Signed-off-by:
Ren Mingxin <renmx@cn.fujitsu.com> Signed-off-by:
-
Hannes Reinecke authored
32bit accesses are guaranteed to be atomic, so we can remove the spinlock when checking for eh_deadline. We only need to make sure to catch any updates which might happened during the call to time_before(); if so we just recheck with the correct value. Signed-off-by:
-
Hannes Reinecke authored
When a command runs into a timeout we need to send an 'ABORT TASK' TMF. This is typically done by the 'eh_abort_handler' LLDD callback. Conceptually, however, this function is a normal SCSI command, so there is no need to enter the error handler. This patch implements a new scsi_abort_command() function which invokes an asynchronous function scsi_eh_abort_handler() to abort the commands via the usual 'eh_abort_handler'. If abort succeeds the command is either retried or terminated, depending on the number of allowed retries. However, 'eh_eflags' records the abort, so if the retry would fail again the command is pushed onto the error handler without trying to abort it (again); it'll be cleared up from SCSI EH. [hare: smatch detected stray switch fixed] Signed-off-by:
-
James Bottomley authored
Commit 18a4d0a2 (Handle disk devices which can not process medium access commands) was introduced to offline any device which cannot process medium access commands. However, commit 3eef6257 (Reduce error recovery time by reducing use of TURs) reduced the number of TURs by sending it only on the first failing command, which might or might not be a medium access command. So in combination this results in an erratic device offlining during EH; if the command where the TUR was sent upon happens to be a medium access command the device will be set offline, if not everything proceeds as normal. This patch moves the check to the final test, eliminating this problem. Signed-off-by:
-
Paul Gortmaker authored
After getting warnings in an allyesconfig build[1] from this driver, I decided to remind myself just how old it was, and whether it warranted fixing. In the Kconfig help text, I found: "This driver will eventually be phased out entirely" Going back to the history archive, I see the line was added[2] in Feb 2002, when we moved from v2.4.2.1 ---> v2.4.2.2 So, with over a decade of notification, and multiple major releases since then, I think we can justify removing this. Currently we have people wasting time building it during routine testing, and then wasting more time re-researching the known reported warnings, only to find that nobody really is willing to integrate the fixes[3] for it. A quick search didn't seem to indicate any active user base for it. If someone happens to have a quirky _old_ card that the eleven year old "new" driver doesn't work with, then it is entirely reasonable that they stick with a kernel version that predates this removal. [1] drivers/scsi/aic7xxx_old.c: In function ‘aic7xxx_register’: drivers/scsi/aic7xxx_old.c:7901:5: warning: case value ‘257’ not in enumerated type ‘ahc_chip’ [-Wswitch] drivers/scsi/aic7xxx_old.c:7898:5: warning: case value ‘513’ not in enumerated type ‘ahc_chip’ [-Wswitch] drivers/scsi/aic7xxx_old.c: In function ‘aic7xxx_load_seeprom’: drivers/scsi/aic7xxx_old.c:8517:5: warning: case value ‘257’ not in enumerated type ‘ahc_chip’ [-Wswitch] drivers/scsi/aic7xxx_old.c:8510:5: warning: case value ‘513’ not in enumerated type ‘ahc_chip’ [-Wswitch] [2] http://git.kernel.org/cgit/linux/kernel/git/tglx/history.git commit 44e8778c [3] https://lkml.org/lkml/2012/10/29/215Signed-off-by:Paul Gortmaker <paul.gortmaker@windriver.com> Acked-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Douglas Gilbert authored
update sg MAINTAINERS file entry: web site and documentation entry Signed-off-by:
Douglas Gilbert <dgilbert@interlog.com> Signed-off-by:
-
Saurav Kashyap authored
Signed-off-by:
-
Saurav Kashyap authored
Signed-off-by:
-
Armen Baloyan authored
Signed-off-by:
Armen Baloyan <armen.baloyan@qlogic.com> Signed-off-by:
-
Sawan Chandak authored
Signed-off-by:
Sawan Chandak <sawan.chandak@qlogic.com> Signed-off-by:
-
Chad Dupuis authored
Signed-off-by:
Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by:
-
Sawan Chandak authored
Signed-off-by:
-
Chad Dupuis authored
Signed-off-by:
-
Armen Baloyan authored
[SCSI] qla2xxx: Add changes to obtain ISPFX00 adapters product information in accordance with firmware update. Signed-off-by:
-
Armen Baloyan authored
Signed-off-by:
-
Atul Deshmukh authored
Signed-off-by:
Atul Deshmukh <atul.deshmukh@qlogic.com> Signed-off-by:
-
Joe Carnuccio authored
Signed-off-by:
Joe Carnuccio <joe.carnuccio@qlogic.com> Signed-off-by:
-
Joe Carnuccio authored
Signed-off-by:
-
Armen Baloyan authored
Signed-off-by:
-
Chad Dupuis authored
If we become disconnected from the PCI bus/PCIe fabric, there can be long delays in register reads which can cause erroneous decisions to be made and cause a soft lockup if a lock is held too long. As a preventative measure, check for a disconnection (register reads that return -1) and then disable the board if we find ourselves in this condition. For now, check in our interrupt handlers and the per adapter one second timer. Signed-off-by:
-
Chad Dupuis authored
Signed-off-by:
-
Chad Dupuis authored
[SCSI] Revert "qla2xxx: Ramp down queue depth for attached SCSI devices when driver resources are low." This reverts commit 3c290d0bSigned-off-by:
-
