- 28 Mar, 2023 2 commits
-
-
Ville Syrjälä authored
Similar to FBC let's expose an debugfs file to control IPS false color. Enabling this provides an immediate visual feedback on whether IPS is working or not. Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230327133942.22063-2-ville.syrjala@linux.intel.comReviewed-by:
Jani Nikula <jani.nikula@intel.com>
-
Ville Syrjälä authored
IPS is a per-pipe feature, so let's move the debugfs stuff under the crtc directory, and only register it when IPS is actually available. Signed-off-by:
-
- 27 Mar, 2023 2 commits
-
-
Vinod Govindapillai authored
Wrong register address is used to read the SAG block time. Fix the register address according to the bspec. Bspec: 64608 Signed-off-by:
Vinod Govindapillai <vinod.govindapillai@intel.com> Reviewed-by:
Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> Signed-off-by:
-
Vinod Govindapillai authored
Wrong offsets are calculated to read QGV point registers. Fix it to read from the correct registers. Bspec: 64602 Reviewed-by:
-
- 24 Mar, 2023 7 commits
-
-
Ville Syrjälä authored
Currently we have no sane way to forcibly disable SAGV, which makes debugging things a PITA. Manually poking at the pcode mailbox with it's various SAGV/QGV/PSF formats is no fun, and likely to be clobbered by the driver anyway. Let's add a modparam for this. Signed-off-by:
Rodrigo Vivi <rodrigo.vivi@intel.com>
-
Ville Syrjälä authored
All other skl+ universal plane register bit definitions are next to the pipe A register definition. Move the PLANE_BUF_CFG bit definitions there as well. Signed-off-by:
Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
-
Ville Syrjälä authored
Add i915.enable_dpt modparam to allow disabling the DPT usage in hardware via the chicken bit. Useful when debugging potential DPT issues. Quickly smoke tested on ADL. Signed-off-by:
-
Ville Syrjälä authored
Define the PLANE_CHICKEN register offsets. Signed-off-by:
-
Ville Syrjälä authored
Replace the hand rolled DISPLAY_VER check for a more descriptive HAS_DPT() macro. Will be used on more than one place later. Signed-off-by:
-
Ville Syrjälä authored
If we want to test with DPT disabled on ADL the POT stride remap stuff needs to be disabled. Make it depend on actual DPT usage instead of just assuming it based on the modifier. Signed-off-by:
-
Ville Syrjälä authored
Currently i915_gem_object_is_framebuffer() doesn't treat the BO containing the framebuffer's DPT as a framebuffer itself. This means eg. that the shrinker can evict the DPT BO while leaving the actual FB BO bound, when the DPT is allocated from regular shmem. That causes an immediate oops during hibernate as we try to rewrite the PTEs inside the already evicted DPT obj. TODO: presumably this might also be the reason for the DPT related display faults under heavy memory pressure, but I'm still not sure how that would happen as the object should be pinned by intel_dpt_pin() while in active use by the display engine... Cc: stable@vger.kernel.org Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com> Cc: Matthew Auld <matthew.auld@intel.com> Cc: Imre Deak <imre.deak@intel.com> Fixes: 0dc987b6 ("drm/i915/display: Add smem fallback allocation for dpt") Signed-off-by:
-
- 23 Mar, 2023 6 commits
-
-
Suraj Kandpal authored
MTL uses GSC command streamer i.e gsc cs to send HDCP/PXP commands to GSC f/w. It requires to keep hdcp display driver agnostic to content protection f/w (ME/GSC fw) in the form of i915_hdcp_fw_ops generic ops. Adding HDCP GSC CS interface by leveraging the i915_hdcp_fw_ops generic ops instead of I915_HDCP_COMPONENT as integral part of i915. Adding checks to see if GSC is loaded and proxy is setup --v6 -dont change the license date in same patch series [Jani] -fix the license year {Jani] --v8 -remove stale comment [Ankit] -get headers in alphabetical order [Ankit] -fix hdcp2_supported check [Ankit] --v9 -remove return statement from hdcp_gsc_fini [Ankit] Cc: Tomas Winkler <tomas.winkler@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Signed-off-by:Anshuman Gupta <anshuman.gupta@intel.com> Signed-off-by:
Suraj Kandpal <suraj.kandpal@intel.com> Reviewed-by:
Ankit Nautiyal <ankit.k.nautiyal@intel.com> Reviewed-by:
Uma Shankar <uma.shankar@intel.com> Signed-off-by:
-
Suraj Kandpal authored
Add function that takes care of sending command to gsc cs. We start of with allocation of memory for our command intel_hdcp_gsc_message that contains gsc cs memory header as directed in specs followed by the actual payload hdcp message that we want to send. Spec states that we need to poll pending bit of response header around 20 times each try being 50ms apart hence adding that to current gsc_msg_send function Also we use the same function to take care of both sending and receiving hence no separate function to get the response. --v4 -Create common function to fill in gsc_mtl_header [Alan] -define host session bitmask [Alan] --v5 -use i915 directly instead of gt->i915 [Alan] -No need to make fields NULL as we are already using kzalloc [Alan] --v8 -change mechanism to reuse the same memory for one hdcp session[Alan] -fix header ordering -add comments to explain flags and host session mask [Alan] --v9 -remove gem obj from hdcp message as we can use i915_vma_unpin_and_release [Alan] -move hdcp message allocation and deallocation from hdcp2_enable and hdcp2_disable to init and teardown of HDCP [Alan] --v10 -remove unnecessary i915_vma_unpin [Alan] --v11 -fix comment style [Uma] Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Alan Pervin Teres <alan.previn.teres.alexis@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Anshuman Gupta <anshuman.gupta@intel.com> Signed-off-by:
Alan Previn <alan.previn.teres.alexis@intel.com> Reviewed-by:
-
Suraj Kandpal authored
It requires to move intel specific HDCP API structures to i915_hdcp_interface.h from driver/misc/mei/hdcp/mei_hdcp.h so that any content protection fw interfaces can use these structures. Cc: Tomas Winkler <tomas.winkler@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Signed-off-by:
-
Suraj Kandpal authored
There are more than 1 type of content protection security firmware. Make the name generic %s/_mei_/_ --v3 -Changing names to drop cp_fw to make naming more agnostic[Jani] --v4 -remove header reference in intel_display_core.h [Uma] -fix commit message and prefix drm [Uma] Cc: Tomas Winkler <tomas.winkler@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Signed-off-by:
-
Anshuman Gupta authored
pre MTL we interact with mei interface to talk to firmware and enable CP but going forward we will talk to gsc cs because of which we are making all names for HDCP helpers and structures generic as either mei or gsc cs maybe used. Change the include/drm/i915_mei_hdcp_interface.h to include/drm/i915_hdcp_interface.h Change the i915_hdcp_interface.h header naming convention to suit generic f/w type. %s/MEI_/HDCP_ %s/mei_dev/hdcp_dev Change structure name Accordingly. %s/i915_hdcp_comp_master/i915_hdcp_master %s/i915_hdcp_component_ops/i915_hdcp_ops --v6 -make each patch build individually [Jani] --v8 -change ME FW to ME/GSC FW [Ankit] -fix formatting issue [Ankit] --v9 -fix commit message and header [Uma] --v10 -rename comp variable [Uma] Cc: Tomas Winkler <tomas.winkler@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Signed-off-by:
Tomas Winkler <tomas.winkler@intel.com> Signed-off-by:
-
Suraj Kandpal authored
HDCP and PXP will require a common function to allow it to submit commands to the gsc cs. Also adding the gsc mtl header that needs to be added on to the existing payloads of HDCP and PXP. --v4 -Seprate gsc load and heci cmd submission into different functions in different files for better scalability [Alan] -Rename gsc address field [Alan] --v5 -remove extra line is intel_gsc_fw.h [Uma] Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Alan Previn <alan.previn.teres.alexis@intel.com> Signed-off-by: Suraj Kandpal<suraj.kandpal@intel.com> Reviewed-by:
-
- 22 Mar, 2023 14 commits
-
-
Imre Deak authored
The current way to determine during HW state sanitization if a PHY is connected in the expected way doesn't work in all cases. The check for this considers only the PHY ready/owned state and the initial TC mode which was determined earlier by the TC port HW readout - using the sink's HPD and the same PHY ready/owned states. For instance for an enabled DP-alt/TBT port without the PHY ready/owned flags set the initial mode will be TBT, and this will be regarded as a valid PHY state. However it's possible that the port is actually enabled in DP-alt mode, but for some reason the PHY ownership was not acquired. Make sure the driver can detect invalid PHY states as in the above example by checking the PHY ready/owned state wrt. the PLL type used. This should be the TBT PLL if the PHY is not owned and the MG (non-TBT) PLL if the PHY is owned. v2: Rebased on change passing crtc_state in the previous patch. Reviewed-by:
Imre Deak <imre.deak@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230321220101.983366-3-imre.deak@intel.com
-
Imre Deak authored
For clarity factor out the function to determine if there are active links on a TC port. This prepares for the next patch also checking the port's PLL type. While at it pass crtc_state to intel_tc_port_sanitize_mode(), and check hw.active in that, instead of the deprecated crtc->active flag. v2: Check crtc_state->hw.active instead of crtc->active. (Ville) Reviewed-by:
-
Imre Deak authored
Add an encoder hook, which can be called on enabled TC ports to determine if the port uses a TBT or a non-TBT PLL. An upcoming patch will use this to sanity check active TC port's PHY state wrt. the PLL type used by the port. Reviewed-by:
-
Imre Deak authored
Since an HDMI output can only be enabled in legacy mode on TC ports, assume that VBT is wrong and the port is legacy if VBT says the port is non-legacy and has HDMI. If VBT says to enable DP as well leave the non-legacy flag enabled, relying on the flag getting fixed up based on the HPD status during sink detection. v2: Fix the legacy port flag only if DP is not enabled. Reviewed-by:
-
Imre Deak authored
For consistency detect the initial TC mode in the PHY owned state the same way this is done in the not owned state (w/o changing the behavior). While at it, add more details to the PHY state debug print. Signed-off-by:
-
Imre Deak authored
Atm, a TC port's initial mode will be read out as TBT mode in any case the PHY ownership is not held. This isn't correct for legacy ports which should be used only in legacy mode. Fix the above initial mode to be disconnected mode for a legacy port and TBT mode for DP-alt/TBT ports. Determine the port type by checking first the HPD state and then the legacy VBT flag (so the HPD state can correct a bogus VBT flag). If a sink is connected on a disabled port the PHY will get also connected (switching it to legacy mode on a legacy port). Also connect the PHY on a legacy port if it's enabled but BIOS incorrectly left it in the disconnected state for some reason. Signed-off-by:
-
Imre Deak authored
A legacy TC port can't be switched to TBT mode, even if the PHY initialization wasn't ready yet for some reason, so prevent this. This shouldn't normally happen as the driver waits for the IOM/TCSS PHY initialization during driver loading and system resume. Signed-off-by:
-
Imre Deak authored
Atm, the target TC mode - which the PHY should be switched to at any point it's used - is TBT in case there is no sink connected. However legacy ports are only used in the legacy mode regardless of the sink connected state. Fix the mode returned by intel_tc_port_get_target_mode() accordingly. Despite of the above issue, the PHY got disconnected as expected in response to a sink disconnect event, causing only a redundant PHY disconnect->reconnect sequence whenever the port was used. Signed-off-by:
-
Imre Deak authored
Factor out helpers used later in the patchset to convert an HPD status mask to TC mode or target TC mode. No functional changes. Signed-off-by:
-
Imre Deak authored
During boot-up/system resume, the TC PHY on legacy ports will be initialized by the IOM/TCSS firmware regardless of a sink being connected or not (as opposed to DP-alt/TBT ports, which the FW only inits once a sink is connected). Wait for the above initialization to complete during HW readout, so that connecting the PHY later will already see the expected PHY ready state. Signed-off-by:
-
Imre Deak authored
At least restoring the MST topology during system resume needs to use AUX before the display HW readout->sanitization sequence is complete, but on TC ports the PHY may be in the wrong mode for this, resulting in the AUX transfers to fail. The initial TC port mode is kept fixed as BIOS left it for the above HW readout sequence (to prevent changing the mode on an enabled port). If the port is disabled this initial mode is TBT - as in any case the PHY ownership is not held - even if a DP-alt sink is connected. Thus, the AUX transfers during this time will use TBT mode instead of the expected DP-alt mode and so time out. Fix the above by connecting the PHY during port initialization if the port is disabled, which will switch to the expected mode (DP-alt in the above case). As the encoder/pipe HW state isn't read-out yet at this point, check if the port is enabled based on the DDI_BUF enabled flag. Save the read-out initial mode, so intel_tc_port_sanitize_mode() can check this wrt. the read-out encoder HW state. Signed-off-by:
-
Imre Deak authored
The commit renaming icl_tc_phy_is_in_safe_mode() to icl_tc_phy_take_ownership() didn't flip the function's return value accordingly, fix this up. This didn't cause an actual problem besides state check errors, since the function is only used during HW readout. Cc: José Roberto de Souza <jose.souza@intel.com> Fixes: f53979d6 ("drm/i915/display/tc: Rename safe_mode functions ownership") Reviewed-by:
José Roberto de Souza <jose.souza@intel.com> Reviewed-by:
-
Imre Deak authored
An enabled TC MST port holds one TC port link reference, regardless of the number of enabled streams on it, but the TC port HW readout takes one reference for each active MST stream. Fix the HW readout, taking only one reference for MST ports. This didn't cause an actual problem, since the encoder HW readout doesn't yet support reading out the MST HW state. Signed-off-by:
Mika Kahola <mika.kahola@intel.com> Reviewed-by:
Andrzej Hajda <andrzej.hajda@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-3-imre.deak@intel.com
-
Imre Deak authored
On TC ports the 4ms AUX timeout combined with the 5 * 32 retry attempts during DPCD accesses adds a 640ms delay to each access if the sink is disconnected. This in turn slows down a modeset during which the sink is disconnected (for instance a disabling modeset). Prevent the above delay by aborting AUX transfers on a TC port with a disconnected sink. The DP 1.4a link CTS (4.2.1.5 Source Device Inactive HPD / Inactive AUX Test") also requires not to initiate AUX transfers on disconnected DP ports in general, however this patch doesn't change the behavior on non-TC ports, leaving that for a follow-up. Reported-and-tested-by:
Chris Chiu <chris.chiu@canonical.com> Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8279Reviewed-by:
-
- 21 Mar, 2023 9 commits
-
-
Ville Syrjälä authored
Keeping DC states enabled is incompatible with the _noarm()/_arm() split we use for writing pipe/plane registers. When DC5 and PSR are enabled, all pipe/plane registers effectively become self-arming on account of DC5 exit arming the update, and PSR exit latching it. What probably saves us most of the time is that (with PIPE_MISC[21]=0) all pipe register writes themselves trigger PSR exit, and then we don't re-enter PSR until the idle frame count has elapsed. So it may be that the PSR exit happens already before we've updated the state too much. Also the PSR1 panel (at least on this KBL) seems to discard the first frame we trasmit, presumably still scanning out from its internal framebuffer at that point. So only the second frame we transmit is actually visible. But I suppose that could also be panel specific behaviour. I haven't checked out how other PSR panels behave, nor did I bother to check what the eDP spec has to say about this. And since this really is all about DC states, let's switch from the MODESET domain to the DC_OFF domain. Functionally they are 100% identical. We should probably remove the MODESET domain... And for good measure let's toss in an assert to the place where we do the _noarm() register writes to make sure DC states are in fact off. v2: Just use intel_display_power_is_enabled() (Imre) Cc: <stable@vger.kernel.org> #v5.17+ Cc: Manasi Navare <navaremanasi@google.com> Cc: Drew Davenport <ddavenport@chromium.org> Cc: Jouni Högander <jouni.hogander@intel.com> Reviewed-by:
-
Ville Syrjälä authored
Unlike SKL/GLK the ICL CSC unit suffers from a new issue where CSC_MODE arming is sticky. That is, once armed it remains armed causing the CSC coeff/offset registers to become effectively self-arming. CSC coeff/offset registers writes no longer disarm the CSC, but fortunately register read still do. So we can use that to disarm the CSC unit once the registers for the current frame have been latched. This avoid s the self-arming behaviour from persisting into the next frame's .color_commit_noarm() call. Cc: <stable@vger.kernel.org> #v5.19+ Cc: Manasi Navare <navaremanasi@google.com> Cc: Drew Davenport <ddavenport@chromium.org> Cc: Imre Deak <imre.deak@intel.com> Cc: Jouni Högander <jouni.hogander@intel.com> Fixes: d13dde44 ("drm/i915: Split pipe+output CSC programming to noarm+arm pair") Signed-off-by:
-
Ville Syrjälä authored
We're going to need stuff after the color management register latching has happened. Add a corresponding hook. Cc: <stable@vger.kernel.org> #v5.19+ Cc: Manasi Navare <navaremanasi@google.com> Cc: Drew Davenport <ddavenport@chromium.org> Cc: Imre Deak <imre.deak@intel.com> Cc: Jouni Högander <jouni.hogander@intel.com> Signed-off-by:
-
Ville Syrjälä authored
SKL/GLK CSC unit suffers from a nasty issue where a CSC coeff/offset register read or write between DC5 exit and PSR exit will undo the CSC arming performed by DMC, and then during PSR exit the hardware will latch zeroes into the active CSC registers. This causes any plane going through the CSC to output all black. We can sidestep the issue by making sure the PSR exit has already actually happened before we touch the CSC coeff/offset registers. Easiest way to guarantee that is to just move the CSC programming back into the .color_commir_arm() as we force a PSR exit (and crucially wait for it to actually happen) prior to touching the arming registers. When PSR (and thus also DC states) are disabled we don't have anything to worry about, so we can keep using the more optional _noarm() hook for writing the CSC registers. Cc: <stable@vger.kernel.org> #v5.19+ Cc: Manasi Navare <navaremanasi@google.com> Cc: Drew Davenport <ddavenport@chromium.org> Cc: Imre Deak <imre.deak@intel.com> Cc: Jouni Högander <jouni.hogander@intel.com> Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8283 Fixes: d13dde44 ("drm/i915: Split pipe+output CSC programming to noarm+arm pair") Signed-off-by:
-
Ville Syrjälä authored
We're going to want different behavior for skl/glk vs. icl in .color_commit_noarm(), so split the hook into two. Arguably we already had slightly different behaviour since csc_enable/gamma_enable are never set on icl+, so the old code was perhaps a bit confusing as well. Cc: <stable@vger.kernel.org> #v5.19+ Cc: Manasi Navare <navaremanasi@google.com> Cc: Drew Davenport <ddavenport@chromium.org> Cc: Imre Deak <imre.deak@intel.com> Cc: Jouni Högander <jouni.hogander@intel.com> Signed-off-by:
-
Arun R Murthy authored
Enable SDP error detection configuration, this will set CRC16 in 128b/132b link layer. For Display version 13 a hardware bit31 in register VIDEO_DIP_CTL is added to enable/disable SDP CRC applicable for DP2.0 only, but the default value of this bit will enable CRC16 in 128b/132b hence skipping this write. Corrective actions on SDP corruption is yet to be defined. v2: Moved the CRC enable to link training init(Jani N) v3: Moved crc enable to ddi pre enable <Jani N> v4: Separate function for SDP CRC16 (Jani N) Signed-off-by:
Arun R Murthy <arun.r.murthy@intel.com> Reviewed-by:
-
Arun R Murthy authored
DP2.0 E11 defines a new register to facilitate SDP error detection by a 128B/132B capable DPRX device. v2: Update the macro name to reflect the DP spec(Harry) Signed-off-by:
Harry Wentland <harry.wentland@amd.com> Signed-off-by:
Thomas Zimmermann <tzimmermann@suse.de> Link: https://patchwork.freedesktop.org/patch/msgid/20230302081532.765821-2-arun.r.murthy@intel.com
-
Maarten Lankhorst authored
This prevents a namespace collision on other archs. Signed-off-by:
Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Signed-off-by:
-
Jani Nikula authored
The pipe may differ from crtc index if pipes are fused off. For testing purposes, IGT needs to know the pipe. There's already a I915_GET_PIPE_FROM_CRTC_ID IOCTL for this. However, the upcoming Xe driver won't have that IOCTL, and going forward, we'll want a unified interface for testing i915 and Xe, as they share the display code. Thus add the debugfs for i915 display. v2: User letters for pipe names (Ville) Cc: Bhanuprakash Modem <bhanuprakash.modem@intel.com> Reviewed-by:
Bhanuprakash Modem <bhanuprakash.modem@intel.com> Signed-off-by:
-
