This fix (not very clean though) should fix the long time USB3
issue that was spotted last year. The rational has been given by
Hans de Goede:

 ----

I think the most likely cause for this is a firmware bug
in the unifying receiver, likely a race condition.

The most prominent difference between having a USB-2 device
plugged into an EHCI (so USB-2 only) port versus an XHCI
port will be inter packet timing. Specifically if you
send packets (ie hid reports) one at a time, then with
the EHCI controller their will be a significant pause
between them, where with XHCI they will be very close
together in time.

The reason for this is the difference in EHCI / XHCI
controller OS <-> driver interfaces.

For non periodic endpoints (control, bulk) the EHCI uses a
circular linked-list of commands in dma-memory, which it
follows to execute commands, if the list is empty, it
will go into an idle state and re-check periodically.

The XHCI uses a ring of commands per endpoint, and if the OS
places anything new on the ring it will do an ioport write,
waking up the XHCI making it send the new packet immediately.

For periodic transfers (isoc, interrupt) the delay between
packets when sending one at a time (rather then queuing them
up) will be even larger, because they need to be inserted into
the EHCI schedule 2 ms in the future so the OS driver can be
sure that the EHCI driver does not try to start executing the
time slot in question before the insertion has completed.

So a possible fix may be to insert a delay between packets
being send to the receiver.

 ----

I tested this on a buggy Haswell USB 3.0 motherboard, and I always
get the notification after adding the msleep.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Reformat and reword some of the comments to make them more understandable.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

we used to set the parent of the input device as the parent of
the hid bus. This was introduced when we created hid as a real bus, and
to keep backward compatibility. Now, it's time to proper set the parent
so that sysfs has an idea of which input device is attached to
which hid device.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Add labels for BTN_DPAD_UP, BTN_DPAD_DOWN, BTN_DPAD_LEFT, BTN_DPAD_RIGHT and
BTN_TOOL_QUADTAP.

[jkosina@suse.cz: make changelog more verbose]
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

The entries are not needed, as hid-multitouch gets bound correctly
automatically by contact ID.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

[jkosina@suse.cz: refresh to apply after SIS quirk merging]
Signed-off-by: Emanuel Krenz <emanuelkrenz@web.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

hid-logitech-dj.c driver needs hidraw to work correctly. Without
hidraw, hid-logitech-dj.c fails during probe() and Logitech
Unifying devices HID reports aren't recognized.

The unifying receiver has 3 usb interfaces. When hid-logitech-dj driver is
loaded, interfaces 0 and 1 are discarded.

Interface 2 consists of a hid class interface with 3 collections, each of
which sports the 'vendor' usage, thus, there is no reason for hid_input to
claim any of them. On the other hand, hidraw has no issue in claiming the
collections, even if they are 'vendor'. As of today, hid-logitech-dj uses
hidraw api to send configuration/control reports to interface 2 of the
Unifying receiver.

Without the hid-logitech-dj driver, interfaces 0 and 1 are claimed by
hid-input, as they correspond to a keyboard and a mouse. But that is not
relevant to the discussion.

[jkosina@suse.cz: make the changelog more verbose, thanks to Nestor]
Signed-off-by: Olivier Gay <ogay@logitech.com>
Signed-off-by: Nestor Lopez Casado <nlopezcasad@logitech.com>
Signed-off-by: Mathieu Meisser <mmeisser@logitech.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

I have two Logitech Dual Action gamepads, both have same Vendor/Device id pair.
Newest gamepad (A) can switch between old mode (HID) and XBox gamepad emulation
mode. Old gamepad (B) can only work in HID mode.  In HID mode gamepad A sends
many EPIPE errors during initialization and was disconnected immediately after
connect  to usb port. It works fine in Win and Mac. After adding NOGET quirk in
driver, it was working properly.  Gamepad B works fine before and after
changes. I tested both gamepads with 3.8.0 and 3.11.6 kernels  with modified
driver. Follow patch can apply for current git kernel version. I can send pcap
log from usb bus with both gamepads or any other additional information if it
is needed
Signed-off-by: Vitaly Katraew <zawullon@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Since commit 765e5fbd merged the sis quirk,
then USB_VENDOR_ID_SIS2_TOUCH remains undefined.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Add Synaptics HD touchscreen(06cb:1ac3) to no init report quirk
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Add Synaptics HD touchscreen(06cb:0ac3) to no init report quirk.
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

USB_VENDOR_ID_SIS and USB_VENDOR_ID_SIS2_TOUCH are identical,
so refine the code and merge the quirks.
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

It looks like this typo was introduced by a mistake in a copy-and-paste in
commit ddbe3249.
Signed-off-by: Adam Cozzette <acozzette@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Pull HID updates from Jiri Kosina:
 - i2c-hid is not querying init reports any more, as it's not mandated
   by the spec, and annoys quite a few devices during enumeration, by
   Bibek Basu
 - a lot of fixes for Logitech devices, by Simon Wood
 - hid-apple now has an option to switch between Option and Command
   mode, by Nanno Langstraat
 - Some more workarounds for severely broken ELO devices, by Oliver
   Neukum
 - more devm conversions, by Benjamin Tissoires
 - wiimote correctness fixes, by David Herrmann
 - a lot of added support for various new device IDs and random small
   fixes here and there"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (34 commits)
  HID: enable Mayflash USB Gamecube Adapter
  HID: sony: Add force feedback support for Dualshock3 USB
  Input: usbtouchscreen: ignore eGalax/D-Wav/EETI HIDs
  HID: don't ignore eGalax/D-Wav/EETI HIDs
  HID: roccat: add missing special driver declarations
  HID:hid-lg4ff: Correct Auto-center strength for wheels other than MOMO and MOMO2
  HID:hid-lg4ff: Initialize device properties before we touch autocentering.
  HID:hid-lg4ff: ensure ConstantForce is disabled when set to 0
  HID:hid-lg4ff: Switch autocentering off when strength is set to zero.
  HID:hid-lg4ff: Scale autocentering force properly on Logitech wheel
  HID: roccat: fix Coverity CID 141438
  HID: multitouch: add manufacturer to Kconfig help text
  HID: logitech-dj: small cleanup in rdcat()
  HID: remove self-assignment from hid_input_report
  HID: hid-sensor-hub: fix report size
  HID: i2c-hid: Stop querying for init reports
  HID: roccat: add support for Ryos MK keyboards
  HID: roccat: generalize some common code
  HID: roccat: add new device return value
  HID: wiimote: add pro-controller analog stick calibration
  ...

Pull trivial tree updates from Jiri Kosina:
 "Usual earth-shaking, news-breaking, rocket science pile from
  trivial.git"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
  doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
  doc: add missing files to timers/00-INDEX
  timekeeping: Fix some trivial typos in comments
  mm: Fix some trivial typos in comments
  irq: Fix some trivial typos in comments
  NUMA: fix typos in Kconfig help text
  mm: update 00-INDEX
  doc: Documentation/DMA-attributes.txt fix typo
  DRM: comment: `halve' -> `half'
  Docs: Kconfig: `devlopers' -> `developers'
  doc: typo on word accounting in kprobes.c in mutliple architectures
  treewide: fix "usefull" typo
  treewide: fix "distingush" typo
  mm/Kconfig: Grammar s/an/a/
  kexec: Typo s/the/then/
  Documentation/kvm: Update cpuid documentation for steal time and pv eoi
  treewide: Fix common typo in "identify"
  __page_to_pfn: Fix typo in comment
  Correct some typos for word frequency
  clk: fixed-factor: Fix a trivial typo
  ...

Pull input updates from Dmitry Torokhov:
 "Updates for the input subsystem.  You will get an new drivers for
  Hyper-V synthetic keyboard and for Neonode zForce touchscreens, plus a
  bunch of driver fixes and cleanups"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (49 commits)
  Revert "Input: ALPS - add support for model found on Dell XT2"
  arm: dts: am335x sk: add touchscreen support
  Input: ti_am335x_tsc - fix spelling mistake in TSC/ADC DT binding
  Input: cyttsp4 - replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
  Input: mma8450 - add missing i2c_set_clientdata() in mma8450_probe()
  Input: mpu3050 - add missing i2c_set_clientdata() in mpu3050_probe()
  Input: tnetv107x-keypad - make irqs signed for error handling
  Input: add driver for Neonode zForce based touchscreens
  Input: sh_keysc - enable the driver on all ARM platforms
  Input: remove a redundant max() call
  Input: mousedev - allow disabling even without CONFIG_EXPERT
  Input: allow deselecting serio drivers even without CONFIG_EXPERT
  Input: i8042 - add PNP modaliases
  Input: evdev - fall back to vmalloc for client event buffer
  Input: cypress_ps2 - do not consider data bad if palm is detected
  Input: cypress_ps2 - remove useless cast
  Input: fix PWM-related undefined reference errors
  Input: ALPS - change secondary device's name
  Input: wacom - not all multi-interface devices support touch
  Input: nspire-keypad - add missing clk_disable_unprepare() on error path
  ...

Pull MFD updates from Samuel Ortiz:
 "For the 3.13 merge window we have a couple of new drivers for the AMS
  AS3722 PMIC and for STMicroelectronics STw481x PMIC.

  Although this is a smaller update than usual, we also have:

   - Device tree support for the max77693 driver

   - linux/of.h inclusion for all DT compatible MFD drivers, to avoid
     build breakage in the future

   - Support for Intel Wildcat Point-LP PCH through the lpc_ich driver

   - A small arizona update for new wm5110 DSP registers and a few fixes

   - A small palmas update as well, including an of_device table
     addition and a few minor fixes

   - Two small mfd-core changes, one including a memory leak fix for
     when mfd_add_device() fails

   - Our usual round of minor cleanups and janitorial fixes"

* tag 'mfd-3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next: (63 commits)
  Documentation: mfd: Update s2mps11.txt
  mfd: pm8921: Potential NULL dereference in pm8921_remove()
  mfd: Fix memory leak in mfd_add_devices()
  mfd: Stop setting refcounting pointers in original mfd_cell arrays
  mfd: wm5110: Enable micd clamp functionality
  mfd: lpc_ich: Add Device IDs for Intel Wildcat Point-LP PCH
  mfd: max77693: Fix up bug of wrong interrupt number
  mfd: as3722: Don't export the regmap config
  mfd: twl6040: Remove obsolete cleanup for i2c clientdata
  mfd: tps65910: Remove warning during dt node parsing
  mfd: lpc_sch: Ignore resource conflicts when adding mfd cells
  mfd: ti_am335x_tscadc: Avoid possible deadlock of reg_lock
  mfd: syscon: Return -ENOSYS if CONFIG_MFD_SYSCON is not enabled
  mfd: Add support for ams AS3722 PMIC
  mfd: max77693: Include linux/of.h header
  mfd: tc3589x: Detect the precise version
  mfd: omap-usb: prepare/unprepare clock while enable/disable
  mfd: max77686: Include linux/of.h header
  mfd: max8907: Include linux/of.h header
  mfd: max8997: Include linux/of.h header
  ...

Pull hwmon fixes and updates from Jean Delvare:
 "All lm90 driver fixes and improvements"

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  Documentation: dt: hwmon: Add OF document for LM90
  hwmon: (lm90) Add power control
  hwmon: (lm90) Add support for TI TMP451
  hwmon: (lm90) Use enums for the indexes of temp8 and temp11
  hwmon: (lm90) Add support to handle IRQ
  hwmon: (lm90) Define status bits
  hwmon: (lm90) Fix max6696 alarm handling

Pull second round of block driver updates from Jens Axboe:
 "As mentioned in the original pull request, the bcache bits were pulled
  because of their dependency on the immutable bio vecs.  Kent re-did
  this part and resubmitted it, so here's the 2nd round of (mostly)
  driver updates for 3.13.  It contains:

 - The bcache work from Kent.

 - Conversion of virtio-blk to blk-mq.  This removes the bio and request
   path, and substitutes with the blk-mq path instead.  The end result
   almost 200 deleted lines.  Patch is acked by Asias and Christoph, who
   both did a bunch of testing.

 - A removal of bootmem.h include from Grygorii Strashko, part of a
   larger series of his killing the dependency on that header file.

 - Removal of __cpuinit from blk-mq from Paul Gortmaker"

* 'for-linus' of git://git.kernel.dk/linux-block: (56 commits)
  virtio_blk: blk-mq support
  blk-mq: remove newly added instances of __cpuinit
  bcache: defensively handle format strings
  bcache: Bypass torture test
  bcache: Delete some slower inline asm
  bcache: Use ida for bcache block dev minor
  bcache: Fix sysfs splat on shutdown with flash only devs
  bcache: Better full stripe scanning
  bcache: Have btree_split() insert into parent directly
  bcache: Move spinlock into struct time_stats
  bcache: Kill sequential_merge option
  bcache: Kill bch_next_recurse_key()
  bcache: Avoid deadlocking in garbage collection
  bcache: Incremental gc
  bcache: Add make_btree_freeing_key()
  bcache: Add btree_node_write_sync()
  bcache: PRECEDING_KEY()
  bcache: bch_(btree|extent)_ptr_invalid()
  bcache: Don't bother with bucket refcount for btree node allocations
  bcache: Debug code improvements
  ...

Merge branches 'for-3.12/upstream-fixes', 'for-3.13/holtek', 'for-3.13/i2c-hid', 'for-3.13/logitech', 'for-3.13/multitouch', 'for-3.13/roccat', 'for-3.13/upstream' and 'for-3.13/wiimote' into for-linus

Pull drm regression fix from Dave Airlie:
 "Forgot this one liner was necessary to fix module reload issues
  introduced earlier in the drm pull"

* 'drm-next' of git://people.freedesktop.org/~airlied/linux:
  drm: check for !kdev in drm_unplug_minor()

Merge tag 'blackfin-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux

Pull blackfin updates from Steven Miao:
 "Blackfin gpio changes, add adi pinctrl driver, and bug fixes"

* tag 'blackfin-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux:
  blackfin: fix build warning for unused variable
  smp: bf561: and smb_wmb()/smp_rmb() at ipi send/receive
  pm: use GFP_ATOMIC when pm core call this function
  blackfin: serial: Add serial port_fer and port_mux early platform resources.
  blackfin: pinctrl-adi2: code cleanup after using pinctrl-adi2
  blackfin: adi gpio driver and pinctrl driver support
  bf609: update default config for spi
  Blackfin: bfin_gpio: Use proper mask for comparing pfunc

Pull OpenRISC updates from Jonas Bonn:
 - small cleanups to make allmodconfig pass
 - defconfig refresh
 - a handful of code sanitization patches

* tag 'for-3.13' of git://git.openrisc.net/~jonas/linux:
  openrisc: Refactor or32_early_setup()
  openrisc: Remove unused declaration of __initramfs_start
  openrisc: Use the declarations provided by <asm/sections.h>
  openrisc: Refresh or1ksim_defconfig for v3.12
  openrisc: Refactor 16-bit constant relocation
  openrisc: include: asm: Kbuild: add default "vga.h"
  openrisc: Makefile: append "-D__linux__" to KBUILD_CFLAGS

Pull misc kbuild changes from Michal Marek:
 - make tags fixes again
 - scripts/show_delta fix for newer python
 - scripts/kernel-doc does not fail on unknown function prototype
 - one less coccinelle check this time

* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  scripts/tags.sh: remove obsolete __devinit[const|data]
  scripts/kernel-doc: make unknown function prototype a Warning instead of an Error
  show_delta: Update script to support python versions 2.5 through 3.3
  scripts/coccinelle/api: remove devm_request_and_ioremap.cocci
  scripts/tags.sh: Increase identifier list

Pull kconfig changes from Michal Marek:
 - xconfig stores its setting in a meaningful path
   (~/.config/kernel.org/qconf.conf)
 - kconfig symbol search fix
 - documentation fixes
 - cleanup & comment update
 - fix warning when a kconfig symbol is defined with two different types
 - Yann is now officially listed as maintainer of kconfig, but he
   prefers me to send pull requests for now

* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  MAINTAINERS: New kconfig maintainer
  xconfig: Fix the filename for GUI settings
  kconfig: fix bug in search results string: use strlen(gstr->s), not gstr->len
  kconfig: remove unused definition from scanner
  kconfig: adjust warning message for conflicting types
  kconfig: fix trivial typos and update mconf documentation
  kconfig: add short explanation to SYMBOL_WRITE
  Documentation/kbuild/kconfig.txt: 'make listnewconfig' replaces: yes "" | make oldconfig

Pull kbuild changes from Michal Marek:
 - LTO fixes, but the kallsyms part had to be reverted
 - Pass -Werror=implicit-int and -Werror=strict-prototypes to the
   compiler by default
 - snprintf fix in modpost
 - remove GREP_OPTIONS from the environment to be immune against exotic
   grep option settings

* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  kallsyms: Revert back to 128 max symbol length
  Kbuild: Ignore GREP_OPTIONS env variable
  scripts: kallsyms: Use %zu to print 'size_t'
  scripts/bloat-o-meter: use .startswith rather than fragile slicing
  scripts/bloat-o-meter: ignore changes in the size of linux_banner
  kbuild: replace unbounded sprintf call in modpost
  kbuild, bloat-o-meter: fix static detection
  Kbuild: Handle longer symbols in kallsyms.c
  kbuild: Increase kallsyms max symbol length
  Makefile: enable -Werror=implicit-int and -Werror=strict-prototypes by default

Pull Kconfig cleanups from Mark Salter:
 "Remove some unused config options from C6X and clean up PC_PARPORT
  dependencies.  The latter was discussed here:

    https://lkml.org/lkml/2013/10/8/12"

* tag 'for-linus' of git://linux-c6x.org/git/projects/linux-c6x-upstreaming:
  c6x: remove unused COMMON_CLKDEV Kconfig parameter
  Kconfig cleanup (PARPORT_PC dependencies)
  x86: select ARCH_MIGHT_HAVE_PC_PARPORT
  unicore32: select ARCH_MIGHT_HAVE_PC_PARPORT
  sparc: select ARCH_MIGHT_HAVE_PC_PARPORT
  sh: select ARCH_MIGHT_HAVE_PC_PARPORT
  powerpc: select ARCH_MIGHT_HAVE_PC_PARPORT
  parisc: select ARCH_MIGHT_HAVE_PC_PARPORT
  mips: select ARCH_MIGHT_HAVE_PC_PARPORT
  microblaze: select ARCH_MIGHT_HAVE_PC_PARPORT
  m68k: select ARCH_MIGHT_HAVE_PC_PARPORT
  ia64: select ARCH_MIGHT_HAVE_PC_PARPORT
  arm: select ARCH_MIGHT_HAVE_PC_PARPORT
  alpha: select ARCH_MIGHT_HAVE_PC_PARPORT
  c6x: remove unused parameter in Kconfig

We moved minor deallocation to drm_dev_free() in:
  commit 8f6599da
  Author: David Herrmann <dh.herrmann@gmail.com>
  Date:   Sun Oct 20 18:55:45 2013 +0200

      drm: delay minor destruction to drm_dev_free()

However, this causes a call to drm_unplug_minor(), which should just do
nothing as drm_dev_unregister() already called this.

But a separate patch caused kdev lifetime changes:
  commit 5bdebb18
  Author: Dave Airlie <airlied@redhat.com>
  Date:   Fri Oct 11 14:07:25 2013 +1000

      drm/sysfs: sort out minor and connector device object lifetimes.

Thus making our dev_is_registered() call useles (and even segfault if it
is NULL). Replace it with a simple !kdev test and we're fine.
Reported-by: Huax Lu <huax.lu@intel.com>
Reported-by: Daniel Vetter <daniel@ffwll.ch>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=71208Tested-by: lu hua <huax.lu@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>

Signed-off-by: Steven Miao <realmz6@gmail.com>

add smb_wmb()/smp_rmb() to keep cache coherent
Signed-off-by: Steven Miao <realmz6@gmail.com>

We shouldn't sleep in atomic sections.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>

The serial driver sets up port function manually in early platform probe stage
if the ADI GPIO2 driver is used. Remove the bfin_sport_uart early platform
devices.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>

Signed-off-by: Steven Miao <realmz6@gmail.com>

  - Change fdt pointer (passed from head.S) from unsigned int to void *,
    which allows to kill a cast, and makes it compatible with __dtb_start.
  - Use pr_info(),
  - Extract common part.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux@lists.openrisc.net
Signed-off-by: Jonas Bonn <jonas@southpole.se>

Add OF document for LM90 in Documentation/devicetree/.

[JD: Add this new file to the LM90 MAINTAINERS entry.]
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

The device lm90 can be controlled by the vcc rail.
Adding the regulator support to power on/off the vcc rail.
Enable the "vcc" regulator before accessing the device.

[JD: Rename variables to avoid confusion with registers.]
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

TI TMP451 is mostly compatible with ADT7461, except for
local temperature low byte and max conversion rate.
Add support to the LM90 driver.
Signed-off-by: Wei Ni <wni@nvidia.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Using enums for the indexes and nrs of temp8 and temp11.
This make the code much more readable.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

When the temperature exceed the limit range value,
the driver can handle the interrupt.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Add bit defines for the status register. And add a function
lm90_is_tripped() which will read status register and return
tripped or not, then lm90_alert can call it directly, and in the
future the IRQ thread also can use it.

[JD: Adjusted to include all the new MAX6696 status flags.]
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>