Merge branch 'stable/for-linus-fixes-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen

* 'stable/for-linus-fixes-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xen/swiotlb: Use page alignment for early buffer allocation.
  xen: only limit memory map to maximum reservation for domain 0.

This fixes an odd bug found on a Dell PowerEdge 1850/0RC130
(BIOS A05 01/09/2006) where all of the modules doing pci_set_dma_mask
would fail with:

ata_piix 0000:00:1f.1: enabling device (0005 -> 0007)
ata_piix 0000:00:1f.1: can't derive routing for PCI INT A
ata_piix 0000:00:1f.1: BMDMA: failed to set dma mask, falling back to PIO

The issue was the Xen-SWIOTLB was allocated such as that the end of
buffer was stradling a page (and also above 4GB). The fix was
spotted by Kalev Leonid  which was to piggyback on git commit
e79f86b2 "swiotlb: Use page alignment
for early buffer allocation" which:

	We could call free_bootmem_late() if swiotlb is not used, and
	it will shrink to page alignment.

	So alloc them with page alignment at first, to avoid lose two pages

And doing that fixes the outstanding issue.

CC: stable@kernel.org
Suggested-by: "Kalev, Leonid" <Leonid.Kalev@ca.com>
Reported-and-Tested-by: "Taylor, Neal E" <Neal.Taylor@ca.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>

d312ae87 "xen: use maximum reservation to limit amount of usable RAM"
clamped the total amount of RAM to the current maximum reservation. This is
correct for dom0 but is not correct for guest domains. In order to boot a guest
"pre-ballooned" (e.g. with memory=1G but maxmem=2G) in order to allow for
future memory expansion the guest must derive max_pfn from the e820 provided by
the toolstack and not the current maximum reservation (which can reflect only
the current maximum, not the guest lifetime max). The existing algorithm
already behaves this correctly if we do not artificially limit the maximum
number of pages for the guest case.

For a guest booted with maxmem=512, memory=128 this results in:
 [    0.000000] BIOS-provided physical RAM map:
 [    0.000000]  Xen: 0000000000000000 - 00000000000a0000 (usable)
 [    0.000000]  Xen: 00000000000a0000 - 0000000000100000 (reserved)
-[    0.000000]  Xen: 0000000000100000 - 0000000008100000 (usable)
-[    0.000000]  Xen: 0000000008100000 - 0000000020800000 (unusable)
+[    0.000000]  Xen: 0000000000100000 - 0000000020800000 (usable)
...
 [    0.000000] NX (Execute Disable) protection: active
 [    0.000000] DMI not present or invalid.
 [    0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
 [    0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
-[    0.000000] last_pfn = 0x8100 max_arch_pfn = 0x1000000
+[    0.000000] last_pfn = 0x20800 max_arch_pfn = 0x1000000
 [    0.000000] initial memory mapped : 0 - 027ff000
 [    0.000000] Base memory trampoline at [c009f000] 9f000 size 4096
-[    0.000000] init_memory_mapping: 0000000000000000-0000000008100000
-[    0.000000]  0000000000 - 0008100000 page 4k
-[    0.000000] kernel direct mapping tables up to 8100000 @ 27bb000-27ff000
+[    0.000000] init_memory_mapping: 0000000000000000-0000000020800000
+[    0.000000]  0000000000 - 0020800000 page 4k
+[    0.000000] kernel direct mapping tables up to 20800000 @ 26f8000-27ff000
 [    0.000000] xen: setting RW the range 27e8000 - 27ff000
 [    0.000000] 0MB HIGHMEM available.
-[    0.000000] 129MB LOWMEM available.
-[    0.000000]   mapped low ram: 0 - 08100000
-[    0.000000]   low ram: 0 - 08100000
+[    0.000000] 520MB LOWMEM available.
+[    0.000000]   mapped low ram: 0 - 20800000
+[    0.000000]   low ram: 0 - 20800000

With this change "xl mem-set <domain> 512M" will successfully increase the
guest RAM (by reducing the balloon).

There is no change for dom0.
Reported-and-Tested-by: George Shuklin <george.shuklin@gmail.com>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: stable@kernel.org
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/radeon/kms: add some new pci ids

* tag 'tytso-for-linus-20111214' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: handle EOF correctly in ext4_bio_write_page()
  ext4: remove a wrong BUG_ON in ext4_ext_convert_to_initialized
  ext4: correctly handle pages w/o buffers in ext4_discard_partial_buffers()
  ext4: avoid potential hang in mpage_submit_io() when blocksize < pagesize
  ext4: avoid hangs in ext4_da_should_update_i_disksize()
  ext4: display the correct mount option in /proc/mounts for [no]init_itable
  ext4: Fix crash due to getting bogus eh_depth value on big-endian systems
  ext4: fix ext4_end_io_dio() racing against fsync()

.. using the new signed tag merge of git that now verifies the gpg
signature automatically.  Yay.  The branchname was just 'dev', which is
prettier.  I'll tell Ted to use nicer tag names for future cases.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: llseek fix race
  fuse: fix llseek bug
  fuse: fix fuse_retrieve

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fs/ncpfs: fix error paths and goto statements in ncp_fill_super()
  configfs: register_filesystem() called too early
  fuse: register_filesystem() called too early
  ubifs: too early register_filesystem()
  ... and the same kind of leak for mqueue
  procfs: fix a vfsmount longterm reference leak

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=43739Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

The label 'out_bdi' should be followed by bdi_destroy() instead of
fput() which should be after the 'out_fput' label.

If bdi_setup_and_register() fails then jump to the 'out_fput' label
instead of the 'out_bdi' one.

If fget(data.info_fd) fails then jump to the previously fixed 'out_bdi'
label to call bdi_destroy() otherwise the bdi object will not be
destroyed.

Compile tested only.
Signed-off-by: Djalal Harouni <tixxdz@opendz.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

We need to zero out part of a page which beyond EOF before setting uptodate,
otherwise, mapread or write will see non-zero data beyond EOF.
Signed-off-by: Yongqiang Yang <xiaoqiangnk@gmail.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org

If a file is fallocated on a hole, map->m_lblk + map->m_len may be greater
than ee_block + ee_len.
Signed-off-by: Yongqiang Yang <xiaoqiangnk@gmail.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org

If a page has been read into memory and never been written, it has no
buffers, but we should handle the page in truncate or punch hole.

VFS code of writing operations has handled holes correctly, so this
patch removes the code handling holes in writing operations.
Signed-off-by: Yongqiang Yang <xiaoqiangnk@gmail.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org

If there is an unwritten but clean buffer in a page and there is a
dirty buffer after the buffer, then mpage_submit_io does not write the
dirty buffer out.  As a result, da_writepages loops forever.

This patch fixes the problem by checking dirty flag.
Signed-off-by: Yongqiang Yang <xiaoqiangnk@gmail.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org

If the pte mapping in generic_perform_write() is unmapped between
iov_iter_fault_in_readable() and iov_iter_copy_from_user_atomic(), the
"copied" parameter to ->end_write can be zero. ext4 couldn't cope with
it with delayed allocations enabled. This skips the i_disksize
enlargement logic if copied is zero and no new data was appeneded to
the inode.

 gdb> bt
 #0  0xffffffff811afe80 in ext4_da_should_update_i_disksize (file=0xffff88003f606a80, mapping=0xffff88001d3824e0, pos=0x1\
 08000, len=0x1000, copied=0x0, page=0xffffea0000d792e8, fsdata=0x0) at fs/ext4/inode.c:2467
 #1  ext4_da_write_end (file=0xffff88003f606a80, mapping=0xffff88001d3824e0, pos=0x108000, len=0x1000, copied=0x0, page=0\
 xffffea0000d792e8, fsdata=0x0) at fs/ext4/inode.c:2512
 #2  0xffffffff810d97f1 in generic_perform_write (iocb=<value optimized out>, iov=<value optimized out>, nr_segs=<value o\
 ptimized out>, pos=0x108000, ppos=0xffff88001e26be40, count=<value optimized out>, written=0x0) at mm/filemap.c:2440
 #3  generic_file_buffered_write (iocb=<value optimized out>, iov=<value optimized out>, nr_segs=<value optimized out>, p\
 os=0x108000, ppos=0xffff88001e26be40, count=<value optimized out>, written=0x0) at mm/filemap.c:2482
 #4  0xffffffff810db5d1 in __generic_file_aio_write (iocb=0xffff88001e26bde8, iov=0xffff88001e26bec8, nr_segs=0x1, ppos=0\
 xffff88001e26be40) at mm/filemap.c:2600
 #5  0xffffffff810db853 in generic_file_aio_write (iocb=0xffff88001e26bde8, iov=0xffff88001e26bec8, nr_segs=<value optimi\
 zed out>, pos=<value optimized out>) at mm/filemap.c:2632
 #6  0xffffffff811a71aa in ext4_file_write (iocb=0xffff88001e26bde8, iov=0xffff88001e26bec8, nr_segs=0x1, pos=0x108000) a\
 t fs/ext4/file.c:136
 #7  0xffffffff811375aa in do_sync_write (filp=0xffff88003f606a80, buf=<value optimized out>, len=<value optimized out>, \
 ppos=0xffff88001e26bf48) at fs/read_write.c:406
 #8  0xffffffff81137e56 in vfs_write (file=0xffff88003f606a80, buf=0x1ec2960 <Address 0x1ec2960 out of bounds>, count=0x4\
 000, pos=0xffff88001e26bf48) at fs/read_write.c:435
 #9  0xffffffff8113816c in sys_write (fd=<value optimized out>, buf=0x1ec2960 <Address 0x1ec2960 out of bounds>, count=0x\
 4000) at fs/read_write.c:487
 #10 <signal handler called>
 #11 0x00007f120077a390 in __brk_reservation_fn_dmi_alloc__ ()
 #12 0x0000000000000000 in ?? ()
 gdb> print offset
 $22 = 0xffffffffffffffff
 gdb> print idx
 $23 = 0xffffffff
 gdb> print inode->i_blkbits
 $24 = 0xc
 gdb> up
 #1  ext4_da_write_end (file=0xffff88003f606a80, mapping=0xffff88001d3824e0, pos=0x108000, len=0x1000, copied=0x0, page=0\
 xffffea0000d792e8, fsdata=0x0) at fs/ext4/inode.c:2512
 2512                    if (ext4_da_should_update_i_disksize(page, end)) {
 gdb> print start
 $25 = 0x0
 gdb> print end
 $26 = 0xffffffffffffffff
 gdb> print pos
 $27 = 0x108000
 gdb> print new_i_size
 $28 = 0x108000
 gdb> print ((struct ext4_inode_info *)((char *)inode-((int)(&((struct ext4_inode_info *)0)->vfs_inode))))->i_disksize
 $29 = 0xd9000
 gdb> down
 2467            for (i = 0; i < idx; i++)
 gdb> print i
 $30 = 0xd44acbee

This is 100% reproducible with some autonuma development code tuned in
a very aggressive manner (not normal way even for knumad) which does
"exotic" changes to the ptes. It wouldn't normally trigger but I don't
see why it can't happen normally if the page is added to swap cache in
between the two faults leading to "copied" being zero (which then
hangs in ext4). So it should be fixed. Especially possible with lumpy
reclaim (albeit disabled if compaction is enabled) as that would
ignore the young bits in the ptes.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  Revert "x86, efi: Calling __pa() with an ioremap()ed address is invalid"
  x86, efi: Make efi_call_phys_{prelog,epilog} CONFIG_RELOCATABLE-aware

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  ceph: add missing spin_unlock at ceph_mdsc_build_path()
  ceph: fix SEEK_CUR, SEEK_SET regression
  crush: fix mapping calculation when force argument doesn't exist
  ceph: use i_ceph_lock instead of i_lock
  rbd: remove buggy rollback functionality
  rbd: return an error when an invalid header is read
  ceph: fix rasize reporting by ceph_show_options

* 'writeback-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/wfg/linux:
  writeback: set max_pause to lowest value on zero bdi_dirty
  writeback: permit through good bdi even when global dirty exceeded
  writeback: comment on the bdi dirty threshold
  fs: Make write(2) interruptible by a fatal signal
  writeback: Fix issue on make htmldocs

one of the paths was missing spin_unlock
Signed-off-by: Yehuda Sadeh <yehuda@hq.newdream.net>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

same story as with ubifs
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

doing that before you are ready to handle mount() is a Bad Idea(tm)...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

* 'fixes' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
  ARM: 7204/1: arch/arm/kernel/setup.c: initialize arm_dma_zone_size earlier
  ARM: 7185/1: perf: don't assign platform_device on unsupported CPUs
  ARM: 7187/1: fix unwinding for XIP kernels
  ARM: 7186/1: fix Kconfig issue with PHYS_OFFSET and !MMU

Commit 06222e49 got the if wrong so that
it always evaluates as true.  This is semantically harmless, but makes
SEEK_CUR and SEEK_SET needlessly query the server.

Rewrite the if to explicitly enumerate the cases we DO need a valid i_size
to make this code less fragile.
Reported-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Sage Weil <sage@newdream.net>

Fix race between lseek(fd, 0, SEEK_CUR) and read/write.  This was fixed in
generic code by commit 5b6f1eb9 (vfs: lseek(fd, 0, SEEK_CUR) race condition).
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>

The test in fuse_file_llseek() "not SEEK_CUR or not SEEK_SET" always evaluates
to true.

This was introduced in 3.1 by commit 06222e49 (fs: handle SEEK_HOLE/SEEK_DATA
properly in all fs's that define their own llseek) and changed the behavior of
SEEK_CUR and SEEK_SET to always retrieve the file attributes.  This is a
performance regression.

Fix the test so that it makes sense.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
CC: stable@vger.kernel.org
CC: Josef Bacik <josef@redhat.com>
CC: Al Viro <viro@zeniv.linux.org.uk>

Fix two bugs in fuse_retrieve():

 - retrieving more than one page would yield repeated instances of the
   first page

 - if more than FUSE_MAX_PAGES_PER_REQ pages were requested than the
   request page array would overflow

fuse_retrieve() was added in 2.6.36 and these bugs had been there since the
beginning.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
CC: stable@vger.kernel.org

Exactly like roundup_pow_of_two(1), the rounddown version was buggy for
the case of a compile-time constant '1' argument.  Probably because it
originated from the same code, sharing history with the roundup version
from before the bugfix (for that one, see commit 1a06a52e: "Fix
roundup_pow_of_two(1)").

However, unlike the roundup version, the fix for rounddown is to just
remove the broken special case entirely.  It's simply not needed - the
generic code

    1UL << ilog2(n)

does the right thing for the constant '1' argment too.  The only reason
roundup needed that special case was because rounding up does so by
subtracting one from the argument (and then adding one to the result)
causing the obvious problems with "ilog2(0)".

But rounddown doesn't do any of that, since ilog2() naturally truncates
(ie "rounds down") to the right rounded down value.  And without the
ilog2(0) case, there's no reason for the special case that had the wrong
value.

tl;dr: rounddown_pow_of_two(1) should be 1, not 0.
Acked-by: Dmitry Torokhov <dtor@vmware.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (jz4740) Staticise jz4740_hwmon_driver
  hwmon: (jz4740) fix signedness bug

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
  mmc: core: Fix deadlock when the CONFIG_MMC_UNSAFE_RESUME is not defined
  mmc: sdhci-s3c: Remove old and misprototyped suspend operations
  mmc: tmio: fix clock gating on platforms with a .set_pwr() method
  mmc: sh_mmcif: fix clock gating on platforms with a .down_pwr() method
  mmc: core: Fix typo at mmc_card_sleep
  mmc: core: Fix power_off_notify during suspend
  mmc: core: Fix setting power notify state variable for non-eMMC
  mmc: core: Add quirk for long data read time
  mmc: Add module.h include to sdhci-cns3xxx.c
  mmc: mxcmmc: fix falling back to PIO
  mmc: omap_hsmmc: DMA unmap only once in case of MMC error

/proc/mounts was showing the mount option [no]init_inode_table when
the correct mount option that will be accepted by parse_options() is
[no]init_itable.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org

This hangs my MacBook Air at boot time; I get no console
messages at all. I reverted this on top of -rc5 and my machine
boots again.

This reverts commit e8c71062.
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Huang Ying <huang.ying.caritas@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1321621751-3650-1-git-send-email-matt@consoleSigned-off-by: Ingo Molnar <mingo@elte.hu>

If the force argument isn't valid, we should continue calculating a
mapping as if it weren't specified.
Signed-off-by: Sage Weil <sage@newdream.net>

It is not used outside this driver so no need to make the symbol global.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>

wait_for_completion_interruptible_timeout() may return negative value.
In this case, checking if (t > 0)  will return true if t is unsigned.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: stable@kernel.org (3.0+)
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>

Commit 1939dd84 ("ext4: cleanup ext4_ext_grow_indepth code") added a
reference to ext4_extent_header.eh_depth, but forget to pass the value
read through le16_to_cpu.  The result is a crash on big-endian
machines, such as this crash on a POWER7 server:

attempt to access beyond end of device
sda8: rw=0, want=776392648163376, limit=168558560
Unable to handle kernel paging request for data at address 0x6b6b6b6b6b6b6bcb
Faulting instruction address: 0xc0000000001f5f38
cpu 0x14: Vector: 300 (Data Access) at [c000001bd1aaecf0]
    pc: c0000000001f5f38: .__brelse+0x18/0x60
    lr: c0000000002e07a4: .ext4_ext_drop_refs+0x44/0x80
    sp: c000001bd1aaef70
   msr: 9000000000009032
   dar: 6b6b6b6b6b6b6bcb
 dsisr: 40000000
  current = 0xc000001bd15b8010
  paca    = 0xc00000000ffe4600
    pid   = 19911, comm = flush-8:0
enter ? for help
[c000001bd1aaeff0] c0000000002e07a4 .ext4_ext_drop_refs+0x44/0x80
[c000001bd1aaf090] c0000000002e0c58 .ext4_ext_find_extent+0x408/0x4c0
[c000001bd1aaf180] c0000000002e145c .ext4_ext_insert_extent+0x2bc/0x14c0
[c000001bd1aaf2c0] c0000000002e3fb8 .ext4_ext_map_blocks+0x628/0x1710
[c000001bd1aaf420] c0000000002b2974 .ext4_map_blocks+0x224/0x310
[c000001bd1aaf4d0] c0000000002b7f2c .mpage_da_map_and_submit+0xbc/0x490
[c000001bd1aaf5a0] c0000000002b8688 .write_cache_pages_da+0x2c8/0x430
[c000001bd1aaf720] c0000000002b8b28 .ext4_da_writepages+0x338/0x670
[c000001bd1aaf8d0] c000000000157280 .do_writepages+0x40/0x90
[c000001bd1aaf940] c0000000001ea830 .writeback_single_inode+0xe0/0x530
[c000001bd1aafa00] c0000000001eb680 .writeback_sb_inodes+0x210/0x300
[c000001bd1aafb20] c0000000001ebc84 .__writeback_inodes_wb+0xd4/0x140
[c000001bd1aafbe0] c0000000001ebfec .wb_writeback+0x2fc/0x3e0
[c000001bd1aafce0] c0000000001ed770 .wb_do_writeback+0x2f0/0x300
[c000001bd1aafdf0] c0000000001ed848 .bdi_writeback_thread+0xc8/0x340
[c000001bd1aafed0] c0000000000c5494 .kthread+0xb4/0xc0
[c000001bd1aaff90] c000000000021f48 .kernel_thread+0x54/0x70

This is due to getting ext_depth(inode) == 0x101 and therefore running
off the end of the path array in ext4_ext_drop_refs into following
unallocated structures.

This fixes it by adding the necessary le16_to_cpu.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>

We need to make sure iocb->private is cleared *before* we put the
io_end structure on i_completed_io_list.  Otherwise fsync() could
potentially run on another CPU and free the iocb structure out from
under us.
Reported-by: Kent Overstreet <koverstreet@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org

arm_dma_zone_size is used by arm_bootmem_free() which is called by
paging_init(). Thus it needs to be set before calling it.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

mmc_suspend_host() tries to claim host during suspend
and release it only when the bus suspend operation is
compeleted. If CONFIG_MMC_UNSAFE_RESUME is defined and
the host is flagged as removable, mmc_suspend_host()
tries to remove the card. In this process, the file system
sync can get blocked trying to acquire host which is already
claimed by mmc_suspend_host() causing deadlock.

Fix this deadlock by releasing host before ->remove() is called.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Acked-by: Ulf Hansson <ulf.hansson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>

Now that the driver is using dev_pm_ops the suspend operations in the
platform_driver structure won't get called so don't need to be there,
and certainly shouldn't be the same function as dev_pm_ops since the
signatures are different.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

Do not power down the card in .set_ios(), unless MMC_POWER_OFF is
requested. This fixes the SDHI functionality on ecovec.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>