ibss and mesh modes copy the ht capabilites from the band without
overriding the SMPS state. Unfortunately the default value 0 for the
SMPS field means static SMPS instead of disabled.

This results in HT ibss and mesh setups using only single-stream rates,
even though SMPS is not supposed to be active.

Initialize SMPS to disabled for all bands on ieee80211_hw_register to
ensure that the value is sane where it is not overriden with the real
SMPS state.
Reported-by: Elektra Wagenrad <onelektra@gmx.net>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[move VHT TODO comment to a better place]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When an associated station changes its VHT operating mode this
can/will affect the bandwidth it's using, and consequently we
must recalculate the minimum bandwidth we need to use. Failure
to do so can lead to one of two scenarios:
 1) we use a too high bandwidth, this is benign
 2) we use a too narrow bandwidth, causing rate control and
    actual PHY configuration to be out of sync, which can in
    turn cause problems/crashes
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In the current minimum chandef code there's an issue in that the
recalculation can happen after rate control is initialized for a
station that has a wider bandwidth than the current chanctx, and
then rate control can immediately start using those higher rates
which could cause problems.

Observe that first of all that this problem is because we don't
take non-associated and non-uploaded stations into account. The
restriction to non-associated is quite pointless and is one of
the causes for the problem described above, since the rate init
will happen before the station is set to associated; no frames
could actually be sent until associated, but the rate table can
already contain higher rates and that might cause problems.

Also, rejecting non-uploaded stations is wrong, since the rate
control can select higher rates for those as well.

Secondly, it's then necessary to recalculate the minimal config
before initializing rate control, so that when rate control is
initialized, the higher rates are already available. This can be
done easily by adding the necessary function call in rate init.

Change-Id: Ib9bc02d34797078db55459d196993f39dcd43070
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Currently, this attribute is only fetched on station addition, but
not on station change. Since this info is only present in the assoc
request, with full station state support in the driver it cannot be
present when the station is added.

Thus, add support for changing the VHT opmode on station update if
done before (or while) the station is marked as associated. After
this, ignore it, since it used to be ignored.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In the commit below, I forgot to translate the mac80211's
AC to QoS IE order. Moreover, the condition in the if was
wrong. Fix both issues.
This bug would hit only with clients that didn't set all
the ACs as delivery enabled.

Fixes: f438ceb8 ("mac80211: uapsd_queues is in QoS IE order")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This patch fix issue introduced by my previous commit that
tried to ensure enough headroom was present, and instead
broke it.

When forwarding mesh pkt, mac80211 may also add security header,
and it must therefore be taken into account in the needed headroom.

Fixes: d8da0b5d ("mac80211: Ensure enough headroom when forwarding mesh pkt")
Signed-off-by: Cedric Izoard <cedric.izoard@ceva-dsp.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In AP (or VLAN) mode, when unicast 802.11 packets are received,
they might actually be multicast after conversion. In this case
the fast-RX path didn't handle them properly to send them back
to the wireless medium. Implement that by copying the SKB and
sending it back out.

The possible alternative would be to just punt the packet back
to the regular (slow) RX path, but since we have almost all of
the required code here already it's not so complicated to add
here. Punting it back would also mean acquiring the spinlock,
which would be bad for the stated purpose of the fast-RX path,
to enable well-performing parallel RX.

Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Florian Fainelli says:

====================
net: dsa: bcm_sf2: Couple fixes

Here are a couple of fixes for bcm_sf2, please queue these up for -stable
as well, thank you very much!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We are implementing a MDIO bus which is behind another one, so use the
nested version of the accessors to get lockdep annotations correct.

Fixes: 461cd1b0 ("net: dsa: bcm_sf2: Register our slave MDIO bus")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

We make the bcm_sf2 driver override ds->ops which points to
b53_switch_ops since b53_switch_alloc() did the assignent. This is all
well and good until a second b53 switch comes in, and ends up using the
bcm_sf2 operations. Make a proper local copy, substitute the ds->ops
pointer and then override the operations.

Fixes: f458995b ("net: dsa: bcm_sf2: Utilize core B53 driver when possible")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no checking valid value of maxmtu when getting it from
device tree. This resolution added the checking condition to
ensure the assignment is made within a valid range.
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If after too many passes still no image could be emitted, then
swap back to the original program as we do in all other cases
and don't use the one with blinding.

Fixes: 959a7579 ("bpf, x86: add support for constant blinding")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver's ndo_get_stats64() method is not always called under RTNL.
So it can race with driver close or ethtool reconfigurations.  Fix the
race condition by taking tp->lock spinlock in tg3_free_consistent()
when freeing the tp->hw_stats memory block.  tg3_get_stats64() is
already taking tp->lock.
Reported-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The adapter->pmac_id[0] item is used for primary MAC address but
this is not true for adapter->uc_list[0] as is assumed in
be_set_uc_list(). There are N UC addresses copied first from net_device
to adapter->uc_list[1..N] and then N UC addresses from
adapter->uc_list[0..N-1] are sent to HW. So the last UC address is never
stored into HW and address 00:00:00:00;00:00 (from uc_list[0]) is used
instead.

Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Fixes: b7172414 be2net: replace polling with sleeping in the FW completion path
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 988d44b1 "be2net: Avoid redundant addition of mac address in HW"
introduced be_dev_mac_add & be_uc_mac_add helpers that incorrectly
access adapter->uc_list as an array of bytes instead of an array of
be_eth_addr. Consequently NIC is not filled with valid data so unicast
filtering is broken.

Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Fixes: 988d44b1 be2net: Avoid redundant addition of mac address in HW
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we added CALIPSO support in Linux v4.8 we forgot to add it to the
list of supported protocols with display at boot.
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2017-01-06' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
Another single fix, to correctly handle destruction of a
single netlink socket having ownership of multiple objects
(scheduled scan requests and interfaces.)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

vti6 interface is registered before the rtnl_link_ops block
is attached. As a result the resulting RTM_NEWLINK is missing
IFLA_INFO_KIND. Re-order attachment of rtnl_link_ops block to fix.
Signed-off-by: Dave Forster <dforster@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For proper IRQ generation by DP83867 phy the INT/PWDN pin has to be
programmed as an interrupt output instead of a Powerdown input in
Configuration Register 3 (CFG3), Address 0x001E, bit 7 INT_OE = 1. The
current driver doesn't do this and as result IRQs will not be generated by
DP83867 phy even if they are properly configured in DT.

Hence, fix IRQ generation by properly configuring CFG3.INT_OE bit and
ensure that Link Status Change (LINK_STATUS_CHNG_INT) and Auto-Negotiation
Complete (AUTONEG_COMP_INT) interrupt are enabled. After this the DP83867
driver will work properly in interrupt enabled mode.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When running in single IRQ mode, the additional IRQ routines were being
skipped because only the XGMAC interrupt status was being checked.
Update the code so that the additional IRQ routines are checked whenever
an interrupt is received.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The R8A7740 GEther controller supports the packet checksum offloading
but the 'hw_crc' (bad name, I'll fix it) flag isn't set in the R8A7740
data,  thus CSMR isn't cleared...

Fixes: 73a0d907 ("net: sh_eth: add support R8A7740")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As the SH77{34|63} manuals are freely available,  I've checked the EESIPR
values written against the manuals, and they appeared to set the reserved
bits 11-15 (which should be 0 on write). Fix those EESIPR values.

Fixes: 380af9e3 ("net: sh_eth: CPU dependency code collect to "struct sh_eth_cpu_data"")
Fixes: f5d12767 ("sh_eth: get SH77{34|63} support out of #ifdef")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains accumulated Netfilter fixes for your
net tree:

1) Ensure quota dump and reset happens iff we can deliver numbers to
   userspace.

2) Silence splat on incorrect use of smp_processor_id() from nft_queue.

3) Fix an out-of-bound access reported by KASAN in
   nf_tables_rule_destroy(), patch from Florian Westphal.

4) Fix layer 4 checksum mangling in the nf_tables payload expression
   with IPv6.

5) Fix a race in the CLUSTERIP target from control plane path when two
   threads run to add a new configuration object. Serialize invocations
   of clusterip_config_init() using spin_lock. From Xin Long.

6) Call br_nf_pre_routing_finish_bridge_finish() once we are done with
   the br_nf_pre_routing_finish() hook. From Artur Molchanov.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

>From the realtek data sheet, the PID0 should be bit 0.
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A single netlink socket might own multiple interfaces *and* a
scheduled scan request (which might belong to another interface),
so when it goes away both may need to be destroyed.

Remove the schedule_scan_stop indirection to fix this - it's only
needed for interface destruction because of the way this works
right now, with a single work taking care of all interfaces.

Cc: stable@vger.kernel.org
Fixes: 93a1e86c ("nl80211: Stop scheduled scan if netlink client disappears")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Pull xfs fixes from Darrick Wong:

 - fixes for crashes and double-cleanup errors

 - XFS maintainership handover

 - fix to prevent absurdly large block reservations

 - fix broken sysfs getter/setters

* tag 'xfs-for-linus-4.10-rc3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: fix max_retries _show and _store functions
  xfs: update MAINTAINERS
  xfs: fix crash and data corruption due to removal of busy COW extents
  xfs: use the actual AG length when reserving blocks
  xfs: fix double-cleanup when CUI recovery fails

Pull networking fixes from David Miller:

 1) stmmac_drv_probe() can race with stmmac_open() because we register
    the netdevice too early. Fix from Florian Fainelli.

 2) UFO handling in __ip6_append_data() and ip6_finish_output() use
    different tests for deciding whether a frame will be fragmented or
    not, put them in sync. Fix from Zheng Li.

 3) The rtnetlink getstats handlers need to validate that the netlink
    request is large enough, fix from Mathias Krause.

 4) Use after free in mlx4 driver, from Jack Morgenstein.

 5) Fix setting of garbage UID value in sockets during setattr() calls,
    from Eric Biggers.

 6) Packet drop_monitor doesn't format the netlink messages properly
    such that nlmsg_next fails to work, fix from Reiter Wolfgang.

 7) Fix handling of wildcard addresses in l2tp lookups, from Guillaume
    Nault.

 8) __skb_flow_dissect() can crash on pptp packets, from Ian Kumlien.

 9) IGMP code doesn't reset group query timers properly, from Michal
    Tesar.

10) Fix overzealous MAIN/LOCAL route table combining in ipv4, from
    Alexander Duyck.

11) vxlan offload check needs to be more strict in be2net driver, from
    Sabrina Dubroca.

12) Moving l3mdev to packet hooks lost RX stat counters unintentionally,
    fix from David Ahern.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
  sh_eth: enable RX descriptor word 0 shift on SH7734
  sfc: don't report RX hash keys to ethtool when RSS wasn't enabled
  dpaa_eth: Initialize CGR structure before init
  dpaa_eth: cleanup after init_phy() failure
  net: systemport: Pad packet before inserting TSB
  net: systemport: Utilize skb_put_padto()
  LiquidIO VF: s/select/imply/ for PTP_1588_CLOCK
  libcxgb: fix error check for ip6_route_output()
  net: usb: asix_devices: add .reset_resume for USB PM
  net: vrf: Add missing Rx counters
  drop_monitor: consider inserted data in genlmsg_end
  benet: stricter vxlan offloading check in be_features_check
  ipv4: Do not allow MAIN to be alias for new LOCAL w/ custom rules
  net: macb: Updated resource allocation function calls to new version of API.
  net: stmmac: dwmac-oxnas: use generic pm implementation
  net: stmmac: dwmac-oxnas: fix fixed-link-phydev leaks
  net: stmmac: dwmac-oxnas: fix of-node leak
  Documentation/networking: fix typo in mpls-sysctl
  igmp: Make igmp group member RFC 3376 compliant
  flow_dissector: Update pptp handling to avoid null pointer deref.
  ...

The RX descriptor word 0 on SH7734 has the RFS[9:0] field in bits 16-25
(bits  0-15 usually used for that are occupied by the packet checksum).
Thus  we need to set the 'shift_rd0'  field in the SH7734 SoC data...

Fixes: f0e81fec ("net: sh_eth: Add support SH7734")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If we failed to set up RSS on EF10 (e.g. because firmware declared
 RX_RSS_LIMITED), ethtool --show-nfc $dev rx-flow-hash ... should report
 no fields, rather than confusingly reporting what fields we _would_ be
 hashing on if RSS was working.

Fixes: dcb4123c ("sfc: disable RSS when unsupported")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Madalin Bucur says:

====================
dpaa_eth: a couple of fixes

Add cleanup on PHY initialization failure path, avoid using
uninitialized memory at CGR init.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The QBMan CGR options needs to be zeroed before calling the init
function
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: systemport: Fix padding vs. TSB insertion

This patch series fixes how we pad the packets submitted to the SYSTEMPORT
adapter, and how the transmit status block (prepended 8 bytes) fits in the
picture. The first patch is not technically a bug fix, but is required for the
second path to be applied and to greatly simplify the skb length calculation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Inserting the TSB means adding an extra 8 bytes in front the of packet
that is going to be used as metadata information by the TDMA engine, but
stripped off, so it does not really help with the packet padding.

For some odd packet sizes that fall below the 60 bytes payload (e.g: ARP)
we can end-up padding them after the TSB insertion, thus making them 64
bytes, but with the TDMA stripping off the first 8 bytes, they could
still be smaller than 64 bytes which is required to ingress the switch.

Fix this by swapping the padding and TSB insertion, guaranteeing that
the packets have the right sizes.

Fixes: 80105bef ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since we need to pad our packets, utilize skb_put_padto() which
increases skb->len by how much we need to pad, allowing us to eliminate
the test on skb->len right below.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix a minor fallout from the merge of the timers and the networking
trees. The following error may result if the PTP_1588_CLOCK
prerequisites are not available:

drivers/built-in.o: In function `ptp_clock_unregister':
(.text+0x40e0a5): undefined reference to `pps_unregister_source'
drivers/built-in.o: In function `ptp_clock_unregister':
(.text+0x40e0cc): undefined reference to `posix_clock_unregister'
drivers/built-in.o: In function `ptp_clock_event':
(.text+0x40e249): undefined reference to `pps_event'
drivers/built-in.o: In function `ptp_clock_register':
(.text+0x40e5e1): undefined reference to `pps_register_source'
drivers/built-in.o: In function `ptp_clock_register':
(.text+0x40e62c): undefined reference to `posix_clock_register'
drivers/built-in.o: In function `ptp_clock_register':
(.text+0x40e68d): undefined reference to `pps_unregister_source'
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ip6_route_output() never returns NULL so
check dst->error instead of !dst.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The USB core may call reset_resume when it fails to resume asix device.
And USB core can recovery this abnormal resume at low level driver,
the same .resume at asix driver can work too. Add .reset_resume can
avoid disconnecting after backing from system resume, and NFS can
still be mounted after this commit.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull block layer fixes from Jens Axboe:
 "A set of fixes for the current series, one fixing a regression with
  block size < page cache size in the alias series from Jan. Outside of
  that, two small cleanups for wbt from Bart, a nvme pull request from
  Christoph, and a few small fixes of documentation updates"

* 'for-linus' of git://git.kernel.dk/linux-block:
  block: fix up io_poll documentation
  block: Avoid that sparse complains about context imbalance in __wbt_wait()
  block: Make wbt_wait() definition consistent with declaration
  clean_bdev_aliases: Prevent cleaning blocks that are not in block range
  genhd: remove dead and duplicated scsi code
  block: add back plugging in __blkdev_direct_IO
  nvmet/fcloop: remove some logically dead code performing redundant ret checks
  nvmet: fix KATO offset in Set Features
  nvme/fc: simplify error handling of nvme_fc_create_hw_io_queues
  nvme/fc: correct some printk information
  nvme/scsi: Remove START STOP emulation
  nvme/pci: Delete misleading queue-wrap comment
  nvme/pci: Fix whitespace problem
  nvme: simplify stripe quirk
  nvme: update maintainers information

Pull fbdev fixes from Bartlomiej Zolnierkiewicz:

 - bring fbdev subsystem back into Maintained mode

 - add missing devm_ioremap() error checking to cobalt_lcdfb driver

* tag 'fbdev-v4.10-rc2' of git://github.com/bzolnier/linux:
  video: fbdev: cobalt_lcdfb: Handle return NULL error from devm_ioremap
  MAINTAINERS: add myself as maintainer of fbdev