Standardize the DMA setup hooks so that the DMA implementation in
atari_NCR5380.c can be reconciled with pseudo DMA implementation in
NCR5380.c.

Calls to NCR5380_dma_recv_setup() and NCR5380_dma_send_setup() return
a negative value on failure, zero on PDMA transfer success and a positive
byte count for DMA setup success.

This convention is not entirely new, but is now applied consistently.

Also remove a pointless Status Register access: the *phase assignment is
redundant because after NCR5380_transfer_dma() returns control to
NCR5380_information_transfer(), that routine then returns control
to NCR5380_main(), which means *phase is dead.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Those wrapper drivers which use DMA define the REAL_DMA macro and
those which use pseudo DMA define PSEUDO_DMA. These macros need to be
removed for a number of reasons, not least of which is to have drivers
share more code.

Redefine the PDMA send and receive hooks as DMA setup hooks, so that the
DMA code can be shared by all 5380 wrapper drivers. This will help to
reunify the forked core driver.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The io_recovery_delay macro is intended to insert a microsecond delay
between the chip register accesses that begin a DMA operation. This
is reportedly needed for some ISA boards.

Reverse the sense of the macro test so that in the common case,
where no delay is required, drivers need not define the macro.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

For those wrapper drivers which only implement Programmed IO, have
NCR5380_dma_xfer_len() evaluate to zero. That allows PDMA to be easily
disabled at run-time and so the PSEUDO_DMA macro is no longer needed.

Also remove the spin counters used for debugging pseudo DMA drivers.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The only chip that needs the workarounds enabled is an early NMOS
device. That means that the common case is to disable them.

Unfortunately the sense of the flag is such that it has to be set
for the common case.

Rename the flag so that zero can be used to mean "no errata workarounds
needed". This simplifies the code.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Only the atari_scsi and sun3_scsi drivers define DMA_MIN_SIZE.
Both drivers also define NCR5380_dma_xfer_len, which means
DMA_MIN_SIZE can be removed from the core driver.

This removes another discrepancy between the two core drivers.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

For the NCR5380.c core driver, these macros are never used.
If REAL_DMA were to be defined, compilation would fail.

For the atari_NCR5380.c core driver, REAL_DMA is always defined.

Hence these macros are pointless.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Drivers that define PSEUDO_DMA also define NCR5380_dma_xfer_len.
The core driver must call NCR5380_dma_xfer_len which means
FLAG_NO_PSEUDO_DMA can be eradicated from the core driver.

dmx3191d doesn't define PSEUDO_DMA and has no use for FLAG_NO_PSEUDO_DMA,
so remove it there also.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

This change brings a number of improvements: fewer macros, better test
coverage, simpler code and sane Kconfig options. The downside is a small
chance of incompatibility (which seems unavoidable).

CONFIG_SCSI_GENERIC_NCR53C400 exists to enable or inhibit pseudo DMA
transfers when the driver is used with 53C400-compatible cards. Thanks to
Ondrej Zary's patches, PDMA now works which means it can be enabled
unconditionally.

Due to bad design, CONFIG_SCSI_GENERIC_NCR53C400 ties together unrelated
functionality as it sets both PSEUDO_DMA and BIOSPARAM macros. This patch
effectively enables PSEUDO_DMA and disables BIOSPARAM.

The defconfigs and the Kconfig default leave CONFIG_SCSI_GENERIC_NCR53C400
undefined. Red Hat 9 and CentOS 2.1 were the same. This leaves both
PSEUDO_DMA and BIOSPARAM disabled. The effect of this patch should be
better performance from enabling PSEUDO_DMA.

On the other hand, Debian 4 and SLES 10 had CONFIG_SCSI_GENERIC_NCR53C400
enabled, so both PSEUDO_DMA and BIOSPARAM were enabled. This patch might
affect configurations like this by disabling BIOSPARAM. My best guess is
that this could be a problem only in the vanishingly rare case that
1) the CHS values stored in the boot device partition table are wrong and
2) a 5380 card is in use (because PDMA on 53C400 used to be broken).
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

On 64 bit, struct error_info has 6 bytes of padding, which amounts to
over 4k of wasted space in the additional[] array. We could easily get
rid of that by instead using separate arrays for the codes and the
pointers. However, we can do even better than that and save an
additional 6 bytes per entry: In the table, just store the sizeof()
the corresponding string literal. The cumulative sum of these is then
the appropriate offset into additional_text, which is built from the
concatenation (with '\0's inbetween) of the strings.

$ scripts/bloat-o-meter /tmp/vmlinux vmlinux
add/remove: 0/0 grow/shrink: 1/1 up/down: 24/-8488 (-8464)
function                                     old     new   delta
scsi_extd_sense_format                       136     160     +24
additional                                 11312    2824   -8488

The Kconfig help text used to say that CONFIG_SCSI_CONSTANTS=y costs
around 75 KB, but that was a little exaggerated. The actual number was
closer to 44K, and 36K with this patch.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

This is a purely mechanical move of the list of additional sense codes
to a separate file, in preparation for reducing the impact of choosing
CONFIG_SCSI_CONSTANTS=y by about 8k.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

There's little point in breaking these strings over multiple lines.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Pull HID fixes from Jiri Kosina:

 - fix for how scaling linearization is computed in wiimote driver, by
   Cyan Ogilvie

 - endless retry loop fix in generic USB HID core reset-resume handling,
   by Alan Stern

 - two functional fixes affecting particular devices, and oops fix for
   wacom driver, by Jason Gerecke

 - multitouch slot numbering fix from Gabriele Mazzotta

 - a couple more small fixes on top

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: wacom: Support switching from vendor-defined device mode on G9 and G11
  HID: wacom: Initialize hid_data.inputmode to -1
  HID: microsoft: add support for 3 more devices
  HID: multitouch: Synchronize MT frame on reset_resume
  HID: wacom: fix Bamboo ONE oops
  HID: lenovo: Don't use stack variables for DMA buffers
  HID: usbhid: fix inconsistent reset/resume/reset-resume behavior
  HID: wiimote: Fix wiimote mp scale linearization

Pull m68k update from Geert Uytterhoeven.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k/defconfig: Update defconfigs for v4.6-rc2
  m68k: Wire up preadv2 and pwritev2

Pull ARC fixes from Vineet Gupta:
 - fix Kconfig splat due to pcie rework
 - make ethernet work again on axs103
 - provide fb_pgprotect() for future video driver integration

* tag 'arc-4.6-rc4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: [plat-axs103] Enable loop block devices
  Revert "ARC: [plat-axs10x] add Ethernet PHY description in .dts"
  arc: Add our own implementation of fb_pgprotect()
  ARC: Don't source drivers/pci/pcie/Kconfig ourselves

Pull ARM fixes from Russell King:
 "A couple of small fixes, and wiring up the new syscalls which appeared
  during the merge window"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8550/1: protect idiv patching against undefined gcc behavior
  ARM: wire up preadv2 and pwritev2 syscalls
  ARM: SMP enable of cache maintanence broadcast

Pull MMC fixes from Ulf Hansson:
 "Here are a couple of mmc fixes intended for v4.6 rc3:

  MMC host:
   - sdhci: Fix regression setting power on Trats2 board
   - sdhci-pci: Add support and PCI IDs for more Broxton host controllers"

* tag 'mmc-v4.6-rc1' of git://git.linaro.org/people/ulf.hansson/mmc:
  mmc: sdhci-pci: Add support and PCI IDs for more Broxton host controllers
  mmc: sdhci: Fix regression setting power on Trats2 board

Pull i2c fixes from Wolfram Sang:
 "Some bugfixes from I2C:

   - fix a uevent triggered boot problem by removing a useless debug
     print

   - fix sysfs-attributes of the new i2c-demux-pinctrl driver to follow
     standard kernel behaviour

   - fix a potential division-by-zero error (needed two takes)"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: jz4780: really prevent potential division by zero
  Revert "i2c: jz4780: prevent potential division by zero"
  i2c: jz4780: prevent potential division by zero
  i2c: mux: demux-pinctrl: Update docs to new sysfs-attributes
  i2c: mux: demux-pinctrl: Clean up sysfs attributes
  i2c: prevent endless uevent loop with CONFIG_I2C_DEBUG_CORE

This reverts commit 1028b55b.

It's broken: it makes ext4 return an error at an invalid point, causing
the readdir wrappers to write the the position of the last successful
directory entry into the position field, which means that the next
readdir will now return that last successful entry _again_.

You can only return fatal errors (that terminate the readdir directory
walk) from within the filesystem readdir functions, the "normal" errors
(that happen when the readdir buffer fills up, for example) happen in
the iterorator where we know the position of the actual failing entry.

I do have a very different patch that does the "signal_pending()"
handling inside the iterator function where it is allowable, but while
that one passes all the sanity checks, I screwed up something like four
times while emailing it out, so I'm not going to commit it today.

So my track record is not good enough, and the stars will have to align
better before that one gets committed.  And it would be good to get some
review too, of course, since celestial alignments are always an iffy
debugging model.

IOW, let's just revert the commit that caused the problem for now.
Reported-by: Greg Thelen <gthelen@google.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull parisc fixes from Helge Deller:
 "Since commit 0de79858 ("parisc: Use generic extable search and
  sort routines") module loading is boken on parisc, because the parisc
  module loader wasn't prepared for the new R_PARISC_PCREL32 relocations.

  In addition, due to that breakage, Mikulas Patocka noticed that
  handling exceptions from modules probably never worked on parisc.  It
  was just masked by the fact that exceptions from modules don't happen
  during normal use.

  This patch series fixes those issues and survives the tests of the
  lib/test_user_copy kernel module test.  Some patches are tagged for
  stable"

* 'parisc-4.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Update comment regarding relative extable support
  parisc: Unbreak handling exceptions from kernel modules
  parisc: Fix kernel crash with reversed copy_from_user()
  parisc: Avoid function pointers for kernel exception routines
  parisc: Handle R_PARISC_PCREL32 relocations in kernel modules

Pull libnvdimm fixes from Dan Williams:
 "Three fixes, the first two are tagged for -stable:

   - The ndctl utility/library gained expanded unit tests illuminating a
     long standing bug in the libnvdimm SMART data retrieval
     implementation.

     It has been broken since its initial implementation, now fixed.

   - Another one line fix for the detection of stale info blocks.

     Without this change userspace can get into a situation where it is
     unable to reconfigure a namespace.

   - Fix the badblock initialization path in the presence of the new (in
     v4.6-rc1) section alignment workarounds.

     Without this change badblocks will be reported at the wrong offset.

  These have received a build success report from the kbuild robot and
  have appeared in -next with no reported issues"

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  libnvdimm, pfn: fix nvdimm_namespace_add_poison() vs section alignment
  libnvdimm, pfn: fix uuid validation
  libnvdimm: fix smart data retrieval

Pull GPIO fixes from Linus Walleij:
 "Here is a set of four GPIO fixes.  The two fixes to the core are
  serious as they are regressing minor architectures.

  Core fixes:

   - Defer GPIO device setup until after gpiolib is initialized.

     It turns out that a few very tightly integrated GPIO platform
     drivers initialize so early (befor core_initcall()) so that the
     gpiolib isn't even initialized itself.  That limits what the
     library can do, and we cannot reference uninitialized fields until
     later.

     Defer some of the initialization until right after the gpiolib is
     initialized in these (rare) cases.

   - As a consequence: do not use devm_* resources when allocating the
     states in the initial set-up of the gpiochip.

  Driver fixes:

   - In ACPI retrieveal: ignore GpioInt when looking for output GPIOs.

   - Fix legacy builds on the PXA without a backing pin controller.

   - Use correct datatype on pca953x register writes"

* tag 'gpio-v4.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: pca953x: Use correct u16 value for register word write
  gpiolib: Defer gpio device setup until after gpiolib initialization
  gpiolib: Do not use devm functions when registering gpio chip
  gpio: pxa: fix legacy non pinctrl aware builds
  gpio / ACPI: ignore GpioInt() GPIOs when requesting GPIO_OUT_*

Pull tty fixes from Greg KH:
 "Here are two tty fixes for issues found.

  One was due to a merge error in 4.6-rc1, and the other a regression
  fix for UML consoles that broke in 4.6-rc1.

  Both have been in linux-next for a while"

* tag 'tty-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: Fix merge of "tty: Refactor tty_open()"
  tty: Fix UML console breakage

Pull USB fixes from Greg KH:
 "Here are some USB fixes and new device ids for 4.6-rc3.

  Nothing major, the normal USB gadget fixes and usb-serial driver ids,
  along with some other fixes mixed in.  All except the USB serial ids
  have been tested in linux-next, the id additions should be fine as
  they are 'trivial'"

* tag 'usb-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits)
  USB: option: add "D-Link DWM-221 B1" device id
  USB: serial: cp210x: Adding GE Healthcare Device ID
  USB: serial: ftdi_sio: Add support for ICP DAS I-756xU devices
  usb: dwc3: keystone: drop dma_mask configuration
  usb: gadget: udc-core: remove manual dma configuration
  usb: dwc3: pci: add ID for one more Intel Broxton platform
  usb: renesas_usbhs: fix to avoid using a disabled ep in usbhsg_queue_done()
  usb: dwc2: do not override forced dr_mode in gadget setup
  usb: gadget: f_midi: unlock on error
  USB: digi_acceleport: do sanity checking for the number of ports
  USB: cypress_m8: add endpoint sanity check
  USB: mct_u232: add sanity checking in probe
  usb: fix regression in SuperSpeed endpoint descriptor parsing
  USB: usbip: fix potential out-of-bounds write
  usb: renesas_usbhs: disable TX IRQ before starting TX DMAC transfer
  usb: renesas_usbhs: avoid NULL pointer derefernce in usbhsf_pkt_handler()
  usb: gadget: f_midi: Fixed a bug when buflen was smaller than wMaxPacketSize
  usb: phy: qcom-8x16: fix regulator API abuse
  usb: ch9: Fix SSP Device Cap wFunctionalitySupport type
  usb: gadget: composite: Access SSP Dev Cap fields properly
  ...

Pull staging and IIO driver fixes from Greg KH:
 "Here are some IIO driver fixes, along with two staging driver fixes
  for 4.6-rc3.

  One staging driver patch reverts the deletion of a driver that
  happened in 4.6-rc1.  We thought that laptop.org was dead, but it's
  still alive and kicking, and has users that were mad we broke their
  hardware by deleting a driver for their machines.  So that driver is
  added back and everyone is happy again.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'staging-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  Revert "Staging: olpc_dcon: Remove obsolete driver"
  staging/rdma/hfi1: select CRC32
  iio: gyro: bmg160: fix buffer read values
  iio: gyro: bmg160: fix endianness when reading axes
  iio: accel: bmc150: fix endianness when reading axes
  iio: st_magn: always define ST_MAGN_TRIGGER_SET_STATE
  iio: fix config watermark initial value
  iio: health: max30100: correct FIFO check condition
  iio: imu: Fix inv_mpu6050 dependencies
  iio: adc: Fix build error of missing devm_ioremap_resource on UM
  iio: light: apds9960: correct FIFO check condition
  iio: adc: max1363: correct reference voltage
  iio: adc: max1363: add missing adc to max1363_id

Pull SCSI fixes from James Bottomley:
 "This is a set of eight fixes.

  Two are trivial gcc-6 updates (brace additions and unused variable
  removal).  There's a couple of cxlflash regressions, a correction for
  sd being overly chatty on revalidation (causing excess log increases).
  A VPD issue which could crash USB devices because they seem very
  intolerant to VPD inquiries, an ALUA deadlock fix and a mpt3sas buffer
  overrun fix"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: Do not attach VPD to devices that don't support it
  sd: Fix excessive capacity printing on devices with blocks bigger than 512 bytes
  scsi_dh_alua: Fix a recently introduced deadlock
  scsi: Declare local symbols static
  cxlflash: Move to exponential back-off when cmd_room is not available
  cxlflash: Fix regression issue with re-ordering patch
  mpt3sas: Don't overreach ioc->reply_post[] during initialization
  aacraid: add missing curly braces

Pull MD fixes from Shaohua Li:
 "This update mainly fixes bugs:

   - fix error handling (Guoqing)
   - fix a crash when a disk is hotremoved (me)
   - fix a dead loop (Wei Fang)"

* tag 'md/4.6-rc2-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
  md/bitmap: clear bitmap if bitmap_create failed
  MD: add rdev reference for super write
  md: fix a trivial typo in comments
  md:raid1: fix a dead loop when read from a WriteMostly disk

Pull power management and ACPI fixes from Rafael Wysocki:
 "Fixes for some issues discovered after recent changes and for some
  that have just been found lately regardless of those changes
  (intel_pstate, intel_idle, PM core, mailbox/pcc, turbostat) plus
  support for some new CPU models (intel_idle, Intel RAPL driver,
  turbostat) and documentation updates (intel_pstate, PM core).

  Specifics:

   - intel_pstate fixes for two issues exposed by the recent switch over
     from using timers and for one issue introduced during the 4.4 cycle
     plus new comments describing data structures used by the driver
     (Rafael Wysocki, Srinivas Pandruvada).

   - intel_idle fixes related to CPU offline/online (Richard Cochran).

   - intel_idle support (new CPU IDs and state definitions mostly) for
     Skylake-X and Kabylake processors (Len Brown).

   - PCC mailbox driver fix for an out-of-bounds memory access that may
     cause the kernel to panic() (Shanker Donthineni).

   - New (missing) CPU ID for one apparently overlooked Haswell model in
     the Intel RAPL power capping driver (Srinivas Pandruvada).

   - Fix for the PM core's wakeup IRQs framework to make it work after
     wakeup settings reconfiguration from sysfs (Grygorii Strashko).

   - Runtime PM documentation update to make it describe what needs to
     be done during device removal more precisely (Krzysztof Kozlowski).

   - Stale comment removal cleanup in the cpufreq-dt driver (Viresh
     Kumar).

   - turbostat utility fixes and support for Broxton, Skylake-X and
     Kabylake processors (Len Brown)"

* tag 'pm+acpi-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (28 commits)
  PM / wakeirq: fix wakeirq setting after wakup re-configuration from sysfs
  tools/power turbostat: work around RC6 counter wrap
  tools/power turbostat: initial KBL support
  tools/power turbostat: initial SKX support
  tools/power turbostat: decode BXT TSC frequency via CPUID
  tools/power turbostat: initial BXT support
  tools/power turbostat: print IRTL MSRs
  tools/power turbostat: SGX state should print only if --debug
  intel_idle: Add KBL support
  intel_idle: Add SKX support
  intel_idle: Clean up all registered devices on exit.
  intel_idle: Propagate hot plug errors.
  intel_idle: Don't overreact to a cpuidle registration failure.
  intel_idle: Setup the timer broadcast only on successful driver load.
  intel_idle: Avoid a double free of the per-CPU data.
  intel_idle: Fix dangling registration on error path.
  intel_idle: Fix deallocation order on the driver exit path.
  intel_idle: Remove redundant initialization calls.
  intel_idle: Fix a helper function's return value.
  intel_idle: remove useless return from void function.
  ...

Pull networking fixes from David Miller:

 1) Stale SKB data pointer access across pskb_may_pull() calls in L2TP,
    from Haishuang Yan.

 2) Fix multicast frame handling in mac80211 AP code, from Felix
    Fietkau.

 3) mac80211 station hashtable insert errors not handled properly, fix
    from Johannes Berg.

 4) Fix TX descriptor count limit handling in e1000, from Alexander
    Duyck.

 5) Revert a buggy netdev refcount fix in netpoll, from Bjorn Helgaas.

 6) Must assign rtnl_link_ops of the device before registering it, fix
    in ip6_tunnel from Thadeu Lima de Souza Cascardo.

 7) Memory leak fix in tc action net exit, from WANG Cong.

 8) Add missing AF_KCM entries to name tables, from Dexuan Cui.

 9) Fix regression in GRE handling of csums wrt.  FOU, from Alexander
    Duyck.

10) Fix memory allocation alignment and congestion map corruption in
    RDS, from Shamir Rabinovitch.

11) Fix default qdisc regression in tuntap driver, from Jason Wang.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
  bridge, netem: mark mailing lists as moderated
  tuntap: restore default qdisc
  mpls: find_outdev: check for err ptr in addition to NULL check
  ipv6: Count in extension headers in skb->network_header
  RDS: fix congestion map corruption for PAGE_SIZE > 4k
  RDS: memory allocated must be align to 8
  GRE: Disable segmentation offloads w/ CSUM and we are encapsulated via FOU
  net: add the AF_KCM entries to family name tables
  MAINTAINERS: intel-wired-lan list is moderated
  lib/test_bpf: Add additional BPF_ADD tests
  lib/test_bpf: Add test to check for result of 32-bit add that overflows
  lib/test_bpf: Add tests for unsigned BPF_JGT
  lib/test_bpf: Fix JMP_JSET tests
  VSOCK: Detach QP check should filter out non matching QPs.
  stmmac: fix adjust link call in case of a switch is attached
  af_packet: tone down the Tx-ring unsupported spew.
  net_sched: fix a memory leak in tc action
  samples/bpf: Enable powerpc support
  samples/bpf: Use llc in PATH, rather than a hardcoded value
  samples/bpf: Fix build breakage with map_perf_test_user.c
  ...

Pull btrfs fixes from Chris Mason:
 "These are bug fixes, including a really old fsync bug, and a few trace
  points to help us track down problems in the quota code"

* 'for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: fix file/data loss caused by fsync after rename and new inode
  btrfs: Reset IO error counters before start of device replacing
  btrfs: Add qgroup tracing
  Btrfs: don't use src fd for printk
  btrfs: fallback to vmalloc in btrfs_compare_tree
  btrfs: handle non-fatal errors in btrfs_qgroup_inherit()
  btrfs: Output more info for enospc_debug mount option
  Btrfs: fix invalid reference in replace_path
  Btrfs: Improve FL_KEEP_SIZE handling in fallocate

Pull orangefs fixes from Mike Marshall:
 "Orangefs cleanups and a strncpy vulnerability fix.

  Cleanups:
   - remove an unused variable from orangefs_readdir.
   - clean up printk wrapper used for ofs "gossip" debugging.
   - clean up truncate ctime and mtime setting in inode.c
   - remove a useless null check found by coccinelle.
   - optimize some memcpy/memset boilerplate code.
   - remove some useless sanity checks from xattr.c

  Fix:
   - fix a potential strncpy vulnerability"

* tag 'for-linus-4.6-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux:
  orangefs: remove unused variable
  orangefs: Add KERN_<LEVEL> to gossip_<level> macros
  orangefs: strncpy -> strscpy
  orangefs: clean up truncate ctime and mtime setting
  Orangefs: fix ifnullfree.cocci warnings
  Orangefs: optimize boilerplate code.
  Orangefs: xattr.c cleanup

Pull IOMMU fixes from Joerg Roedel:

 - compile-time fixes (warnings and failures)

 - a bug in iommu core code which could cause the group->domain pointer
   to be falsly cleared

 - fix in scatterlist handling of the ARM common DMA-API code

 - stall detection fix for the Rockchip IOMMU driver

* tag 'iommu-fixes-v4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/vt-d: Silence an uninitialized variable warning
  iommu/rockchip: Fix "is stall active" check
  iommu: Don't overwrite domain pointer when there is no default_domain
  iommu/dma: Restore scatterlist offsets correctly
  iommu: provide of_xlate pointer unconditionally

Make sure we avoid a division-by-zero OOPS in case clock-frequency is
set too low in DT. Add missing '\n' while we are here.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Axel Lin <axel.lin@ingics.com>

This reverts commit 34cf2acd. 'ret' is
not set when bailing out. Also, there is a better place to check for 0.
Reported-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Merge tag 'usb-serial-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus

Johan writes:

USB-serial fixes for v4.6-rc3

Here are some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>

Merge tag 'mac80211-for-davem-2016-04-06' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
For the current RC series, we have the following fixes:
 * TDLS fixes from Arik and Ilan
 * rhashtable fixes from Ben and myself
 * documentation fixes from Luis
 * U-APSD fixes from Emmanuel
 * a TXQ fix from Felix
 * and a compiler warning suppression from Jeff
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

I moderate these (lightly loaded) lists to block spam.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update the comment to reflect the changes of commit 0de79858 (parisc: Use
generic extable search and sort routines).
Signed-off-by: Helge Deller <deller@gmx.de>

Handling exceptions from modules never worked on parisc.
It was just masked by the fact that exceptions from modules
don't happen during normal use.

When a module triggers an exception in get_user() we need to load the
main kernel dp value before accessing the exception_data structure, and
afterwards restore the original dp value of the module on exit.
Noticed-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org