The standard snd_soc_info_volsw() allows a two value control to be
defined as an integer control only if the control name ends in
"Volume". It achieves this by creating a substring if it contains
" Volume", and ensuring this exists at the end of the name. The
volume substring is then used to decide whether the type is a
SNDRV_CTL_ELEM_TYPE_INTEGER or SNDRV_CTL_ELEM_TYPE_BOOLEAN.
However this volume substring is only computed for a two value
control.
This means for controls where there are more than two possible
values, the substring is never created, so in this case the
substring remains NULL, and the condition yields
SNDRV_CTL_ELEM_TYPE_BOOLEAN, even though there are more than 2
possible values.
If there are more than 2 possible values for the control,
then it should always be an integer control.

Fixes: aa2a4b89 ("ASoC: ops: Fix boolean/integer detection for simple controls")
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220617153606.2619457-1-sbinding@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:

This patchset adds the missing jack pin remapping needed by upstream
UCM on Chromebooks, suggested by Jaroslav Kysela [1].

These patches were succesfully tested on GeminiLake and JasperLake
platforms, and generalized to other Chromebooks.

[1] https://mailman.alsa-project.org/pipermail/sound-open-firmware/2022-June/004468.html

Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:

Remove warnings with make W=1

Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:

Cleanups suggested by Greg KH during SoundWire reviews, since the
__func__ information can be added with the dyndbg kernel parameter
[1].

The first two patches change the error level in cases where the use of
dev_dbg() was inconsistent with an aborted programming sequence.

[1] https://lore.kernel.org/alsa-devel/20220610023537.27223-2-yung-chuan.liao@linux.intel.com/

Legacy or non DT boot is no longer possible on systems where the
tw4030/5030 is used.

Drop the support for handling legacy pdata and replace it with a local
board_params struct to allow further cleanups on the mfd side.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20220616153521.29701-1-peter.ujfalusi@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

The module and function information can be added with
'modprobe foo dyndbg=+pmf'
Suggested-by: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220616215351.135643-14-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The module and function information can be added with
'modprobe foo dyndbg=+pmf'
Suggested-by: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220616215351.135643-13-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The module and function information can be added with
'modprobe foo dyndbg=+pmf'
Suggested-by: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220616215351.135643-12-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The module and function information can be added with
'modprobe foo dyndbg=+pmf'
Suggested-by: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220616215351.135643-11-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The module and function information can be added with
'modprobe foo dyndbg=+pmf'
Suggested-by: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220616215351.135643-10-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The module and function information can be added with
'modprobe foo dyndbg=+pmf'
Suggested-by: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220616215351.135643-9-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The module and function information can be added with
'modprobe foo dyndbg=+pmf'
Suggested-by: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220616215351.135643-8-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The module and function information can be added with
'modprobe foo dyndbg=+pmf'
Suggested-by: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220616215351.135643-7-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The module and function information can be added with
'modprobe foo dyndbg=+pmf'
Suggested-by: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220616215351.135643-6-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The module and function information can be added with
'modprobe foo dyndbg=+pmf'
Suggested-by: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220616215351.135643-5-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The module and function information can be added with
'modprobe foo dyndbg=+pmf'
Suggested-by: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220616215351.135643-4-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

We report -ENODEV but only use dev_dbg, this is
inconsistent. dev_err() makes sense here.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220616215351.135643-3-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

dev_dbg() is not good-enough since the flow returns an error.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220616215351.135643-2-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The card did not map jack pins to controls, which prevents
PulseAudio/PipeWire from dealing with jack detection. It's likely that
jack detection was only tested with the CRAS server and extensions of
UCM.
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220616214055.134943-14-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The card did not map jack pins to controls, which prevents
PulseAudio/PipeWire from dealing with jack detection. It's likely that
jack detection was only tested with the CRAS server and extensions of
UCM.
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220616214055.134943-13-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The card did not map jack pins to controls, which prevents
PulseAudio/PipeWire from dealing with jack detection. It's likely that
jack detection was only tested with the CRAS server and extensions of
UCM.
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220616214055.134943-12-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The card did not map jack pins to controls, which prevents
PulseAudio/PipeWire from dealing with jack detection. It's likely that
jack detection was only tested with the CRAS server and extensions of
UCM.
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220616214055.134943-11-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The card did not map jack pins to controls, which prevents
PulseAudio/PipeWire from dealing with jack detection. It's likely that
jack detection was only tested with the CRAS server and extensions of
UCM.
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220616214055.134943-10-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The card did not map jack pins to controls, which prevents
PulseAudio/PipeWire from dealing with jack detection. It's likely that
jack detection was only tested with the CRAS server and extensions of
UCM.
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220616214055.134943-9-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The card did not map jack pins to controls, which prevents
PulseAudio/PipeWire from dealing with jack detection. It's likely that
jack detection was only tested with the CRAS server and extensions of
UCM.
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220616214055.134943-8-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The card did not map jack pins to controls, which prevents
PulseAudio/PipeWire from dealing with jack detection. It's likely that
jack detection was only tested with the CRAS server and extensions of
UCM.
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220616214055.134943-7-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The card did not map jack pins to controls, which prevents
PulseAudio/PipeWire from dealing with jack detection. It's likely that
jack detection was only tested with the CRAS server and extensions of
UCM.
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220616214055.134943-6-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The card did not map jack pins to controls, which prevents
PulseAudio/PipeWire from dealing with jack detection. It's likely that
jack detection was only tested with the CRAS server and extensions of
UCM.
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220616214055.134943-5-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The card did not map jack pins to controls, which prevents
PulseAudio/PipeWire from dealing with jack detection. It's likely that
jack detection was only tested with the CRAS server and extensions of
UCM.
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220616214055.134943-4-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The card did not map jack pins to controls, which prevents
PulseAudio/PipeWire from dealing with jack detection. It's likely that
jack detection was only tested with the CRAS server and extensions of
UCM.
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220616214055.134943-3-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The card did not map jack pins to controls, which prevents
PulseAudio/PipeWire from dealing with jack detection. It's likely that
jack detection was only tested with the CRAS server and extensions of
UCM.
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220616214055.134943-2-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Remove warnings

sound/soc/sunxi/sun4i-i2s.c:205: warning: Function parameter or member
'num_din_pins' not described in 'sun4i_i2s_quirks'

sound/soc/sunxi/sun4i-i2s.c:205: warning: Function parameter or member
'num_dout_pins' not described in 'sun4i_i2s_quirks'
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20220616220802.136282-3-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Remove warning

sound/soc/codecs/cs4270.c:672: warning: Excess function parameter 'id'
description in 'cs4270_i2c_probe'
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20220616220802.136282-2-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

IPC4 based firmwares have unconditional support for IMR boot.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220616054910.16690-1-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

There are two occurrences where the pointer array is being assigned a value
that is never read, the pointer gets updated in the next iteration of a
loop. These assignments are redundant and can be removed.

Cleans up clang scan-build warnings:
sound/soc/intel/skylake/skl-topology.c:2953:3: warning: Value stored to
'array' is never read [deadcode.DeadStores]
sound/soc/intel/skylake/skl-topology.c:3602:3: warning: Value stored to
'array' is never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20220614183809.163531-1-colin.i.king@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

The sof_ipc4_volume_put() function returns type bool so returning
-ENOENT means returning true.  Return false instead.

Fixes: 955e84fc ("ASoC: SOF: ipc4-topology: Add control IO ops")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/YqqyDU5BhOzpRjco@kiliSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from Li Chen <lchen.firstlove@zohomail.com>

This series proposes to add simple bit operations for setting, clearing
and testing specific bits with regmap_field and uses them in one of the
sunxi drivers.

Merge series from Bard Liao <yung-chuan.liao@linux.intel.com>:

Add platform abstraction for the Meteor Lake platform.

This platform has significant differences compared to the TGL/ADL
generation: it relies on new hardware using the code name 'ACE' and
only supports the INTEL_IPC4 protocol and firmware architecture based
on the Zephyr RTOS

Appropriately change calls to {regmap/regmap_field}_update_bits()
with {regmap/regmap_field}_set_bits()
and {regmap/regmap_field}_clear_bits() for improved readability.
Signed-off-by: Li Chen <lchen@ambarella.com>
Link: https://lore.kernel.org/r/180eef50e96.cb7c34db60740.8898768158778553647@zohomail.comSigned-off-by: Mark Brown <broonie@kernel.org>

We have set/clear/test operations for regmap, but not for regmap_field yet.
So let's introduce regmap_field helpers too.

In many instances regmap_field_update_bits() is used for simple bit setting
and clearing. In these cases the last argument is redundant and we can
hide it with a static inline function.

This adds three new helpers for simple bit operations: set_bits,
clear_bits and test_bits (the last one defined as a regular function).
Signed-off-by: Li Chen <lchen@ambarella.com>
Link: https://lore.kernel.org/r/180eef422c3.deae9cd960729.8518395646822099769@zohomail.comSigned-off-by: Mark Brown <broonie@kernel.org>