ntb_perf driver has been also updated so to have the multi-port
interface support. User now must specify what peer port is going
to be used to perform the test.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

There are devices (like IDT PCIe switches), which outbound MWs xlat address
is setup on peer side. In this case local side is supposed to allocate
a memory buffer and somehow deliver the xlat DMA address to peer so one
could set the outbound MW up. The MW test is altered so to support both
previous Intel/AMD and new IDT-like devices.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Messages NTB API is now available. ntb_tool driver has been altered
to perform messages send and receive operation. The test of messages
read/write to/from peer device has been added to the script.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Scratchpad NTB API has changed so has the ntb_tool driver. Outbound
Scratchpad DebugFS files have been moved to peer specific directories.
Each scratchpad is now available via separate file. The test code
has been accordingly altered.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

DB interface of ntb_tool driver hasn't been changed much, but
db_valid_mask DebugFS file has still been added. In this case
it's much better to test all valid DB bits instead of using
the predefined mask, which may be incorrect in general.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Link Up and Down methods are used to change NTB link settings on
local side only for multi-port devices. Link is considered up
only if both sides local and peer set it up. Intel/AMD hardware
acts a bit different by assigning the Primary and Secondary roles,
so Primary device only is able to change the link state. Such behaviour
should be reflected in the test code.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Multi-port interface is now available in ntb_tool driver. According
to the new NTB API, there might be more than two devices connected over
NTB. It means each device can have multiple freely enumerated ports.
Each port got index assigned by NTB hardware driver. This test is
performed to determine the local and peer ports as well as their indexes.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

If some of variables like LOC/REM or LOCAL_*/REMOTE_* got
whitespaces, the script may fail with syntax error.

Fixes: a9c59ef7 ("ntb_test: Add a selftest script for the NTB subsystem")
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Former NTB Performance driver could only work with NTB devices, which
got Scratchpads available and had just two ports. Since there are
devices, which don't have Scratchpads and got more than two peer
ports, the performance measuring tool needs to be rewritten. This
patch adds the ability to test any available NTB peer.
Additionally it allows to set NTB memory windows up using any
available data exchange interface: Scratchpad or Message registers.
Some cleanups are also added here.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Former NTB Debugging tool driver supported only the limited
functionality of the recently updated NTB API, which is now available
to work with the truly NTB multi-port devices and devices, which
got NTB Message registers instead of Scratchpads. This patch
fully rewrites the driver so one would fully expose all the new
NTB API interfaces. Particularly it concerns the Message registers,
peer ports API, NTB link settings. Additional cleanups are also added
here.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Current Ping Pong driver can't truly work with multi-port devices.
Additionally it requires the Scratchpad registers being available
on NTB device. This patches rewrites the driver so one would
perform the cyclic Ping-Pong algorithm around all the available
NTB peers and makes it working with NTB hardware, which doesn't
support Scratchpads, but such alternative as NTB Message register.
Additional cleanups are also added here.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Simple (1 << pidx) operation causes undefined behaviour when
pidx >= 32. It must be casted to u64 to match the actual return
value of ntb_link_is_up() method, so to have all the possible
peer indexes covered and to get rid of undefined behaviour.
Additionally there are special macros in "linux/bitops.h" to perform
the bit-set-shift operations, so it's recommended to have them used
for proper bit setting.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

The dma_mask and dma_coherent_mask fields of the NTB struct device
weren't initialized in hardware drivers. In fact it should be done
instead of PCIe interface usage, since NTB clients are supposed to
use NTB API and left unaware of real hardware implementation.
In addition to that ntb_device_register() method shouldn't clear
the passed ntb_dev structure, since it dma_mask is initialized
by hardware drivers.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

There is a common methods signature form used over all the NTB API
like functions naming scheme, arguments names and order, etc.
Recently added NTB messaging API IO callbacks were named a bit
different so should be renamed to be in compliance with the rest
of the API.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Newer gcc (version 7 and 8 presumably) warn about a statement mixing
the << operator with logical and:

drivers/ntb/hw/mscc/ntb_hw_switchtec.c: In function 'switchtec_ntb_init_sndev':
drivers/ntb/hw/mscc/ntb_hw_switchtec.c:888:24: error: '<<' in boolean context, did you mean '<' ? [-Werror=int-in-bool-context]

My interpretation here is that the author must have intended a bitmask
rather than a comparison, so I'm changing the '&&' to '&', which makes
a lot more sense in the context.

Fixes: 1b249475275d ("ntb_hw_switchtec: Allow using Switchtec NTB in multi-partition setups")
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

With Switchtec hardware, the buffer used for a memory window must be
aligned to its size (the hardware only replaces the lower bits). In
certain circumstances dma_alloc_coherent() will not provide a buffer
that adheres to this requirement like when using the CMA and
CONFIG_CMA_ALIGNMENT is set lower than the buffer size.

When we get an unaligned buffer mw_set_trans() should return an error.
We also log an error so we know the cause of the problem.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

When using the max_mw_size parameter of ntb_transport to limit the size of
the Memory windows, communication cannot be established and the queues
freeze.

This is because the mw_size that's reported to the peer is correctly
limited but the size used locally is not. So the MW is initialized
with a buffer smaller than the window but the TX side is using the
full window. This means the TX side will be writing to a region of the
window that points nowhere.

This is easily fixed by applying the same limit to tx_size in
ntb_transport_init_queue().

Fixes: e26a5843 ("NTB: Split ntb_hw_intel and ntb_transport drivers")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

I am no longer employed by Dell EMC.  For the purposes of NTB driver
development and maintenance, please contact me via my personal email.
Signed-off-by: Allen Hubbe <allenbh@gmail.com>
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

If one host crashes and soft reboots, the other host may not see a
link down event. Then when the crashed host comes back up, the
surviving host may not know the link was reset and the NTB clients
may not work without being reset.

To solve this, we send a LINK_FORCE_DOWN message to each peer every
time we come up, before we register the NTB device. If a surviving
host still thinks the link is up it will take it down immediately.
In this way, once the crashed host comes up fully, it will send a
regular link up event as per usual and the link will be properly
restarted.

While we are in the area, this also fixes the MSG_LINK_UP message that
was in the link down function that was reported by Doug Meyers.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reported-by: ThanhTuThai <cruisethai@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

In a crosslink configuration doorbells and messages largely work the
same but the NTB registers must be accessed through the reserved LUT
window. Also, as a bonus, seeing there are now two independent sets of
NTB links, both partitions can actually use all 60 doorbell registers
instead of them having to be split into two for each partition.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Crosslink is a feature of the Switchtec switches that is similar to
the B2B mode of other NTB devices. It allows a system to be designed
that is perfectly symmetric with two identical switches that link
two hosts together.

In order for the system to be symmetric, there is an empty host-less
partition between the two switches which the host must enumerate and
assign BAR addresses to. The firmware in the switch manages this
specially so that the BAR addresses on both sides of the empty
partition will be identical despite being in the same partition with
the same address space.

The driver determines whether crosslink is enabled by a flag set in
the NTB partition info registers which are set by the switch's
configuration file.

When crosslink is enabled, a reserved LUT window is setup to point to
the peer's switch's NTB registers and the local MWs are set to forward
to the host-less partition's BARs. (Yes, this hurts my brain too.)
Once this is setup, largely the same NTB infrastructure is used to
communicate between the two hosts.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

The PFF CSR registers actual mirrors the PCI configuration space
for all the ports in the switch. Previously, this was not needed by
the driver but will be used by the crosslink code to enumerate the
bus in an host-less centre partition.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

This is a prep patch in order to support the crosslink feature which
will require the driver to setup the requester ID table in another
partition as well as it's own. To aid this, create a helper function
which sets up the requester IDs from an array.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

This is a prep patch in order to support the crosslink feature which
will require the driver to use another reserved LUT window. To
simplify this we move the code which sets up the reserved LUT window
into a helper function which will be used by the crosslink
initialization.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

This is a prep patch in order to support the crosslink feature which will
require the driver to use another reserved LUT window. To simplify this,
we add some code to track the number of reserved LUT windows in use
instead of assuming this is always 1.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Allow using Switchtec NTB in setups that have more than two partitions.
Note: this does not enable having multi-host communication, it only
allows for a single NTB link between two hosts in a network that might
have more than two.

Use following logic to determine the NT peer partition:

1) If there are 2 partitions, and the target vector is set in
   the Switchtec configuration, use the partition specified in target
   vector.
2) If there are 2 partitions and target vector is unset
   use the only other partition as specified in the NT EP map.
3) If there are more than 2 partitions and target vector is set
   use the other partition specified in target vector.
4) If there are more than 2 partitions and target vector is unset,
   this is invalid and report an error.
Signed-off-by: Kelvin Cao <kelvin.cao@microsemi.com>
[logang@deltatee.com: commit message fleshed out]
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Trivial addition of "\n" to the dev_* prints where necessary
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Trivial fix to spelling mistake in dev_err error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-By: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Removing dead code since this is not being used.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

There is no need to #define the license of the driver, just put it in
the MODULE_LICENSE() line directly as a text string.

This allows tools that check that the module license matches the source
code license to work properly, as there is no need to unwind the
unneeded dereference, especially when the string is defined just a few
lines above the usage of it.
Reported-and-reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Allen Hubbe <Allen.Hubbe@emc.com>
Cc: Gary R Hook <gary.hook@amd.com>
Cc: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

This resolves a bug which may incorrectly configure the peer host's
LUT for shared memory window access. The code was using the local
host's first BAR number, rather than the peer hosts's first BAR
number, to determine what peer NT control register to program.

The bug will cause the Switchtec NTB link to work only if both peers
have the same first NTB BAR configured. In all other configurations,
the link will not come up, failing silently.

When both hosts have the same first BAR, the configuration works only
because the first BAR numbers happent to be the same. When the hosts
do not have the same first BAR, then the LUT translation will not be
configured in the correct peer LUT and will not give the peer the
shared memory window access required for the link to operate.
Signed-off-by: Doug Meyer <dmeyer@gigaio.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Fixes: 678784a44ae8 ("NTB: switchtec_ntb: Initialize hardware for memory windows")
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Pull x86 retpoline fixlet from Thomas Gleixner:
 "Remove the ESP/RSP thunks for retpoline as they cannot ever work.

  Get rid of them before they show up in a release"

* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/retpoline: Remove the esp/rsp thunk

Pull x86 fixes from Thomas Gleixner:
 "A set of small fixes for 4.15:

   - Fix vmapped stack synchronization on systems with 4-level paging
     and a large amount of memory caused by a missing 5-level folding
     which made the pgd synchronization logic to fail and causing double
     faults.

   - Add a missing sanity check in the vmalloc_fault() logic on 5-level
     paging systems.

   - Bring back protection against accessing a freed initrd in the
     microcode loader which was lost by a wrong merge conflict
     resolution.

   - Extend the Broadwell micro code loading sanity check.

   - Add a missing ENDPROC annotation in ftrace assembly code which
     makes ORC unhappy.

   - Prevent loading the AMD power module on !AMD platforms. The load
     itself is uncritical, but an unload attempt results in a kernel
     crash.

   - Update Peter Anvins role in the MAINTAINERS file"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/ftrace: Add one more ENDPROC annotation
  x86: Mark hpa as a "Designated Reviewer" for the time being
  x86/mm/64: Tighten up vmalloc_fault() sanity checks on 5-level kernels
  x86/mm/64: Fix vmapped stack syncing on very-large-memory 4-level systems
  x86/microcode: Fix again accessing initrd after having been freed
  x86/microcode/intel: Extend BDW late-loading further with LLC size check
  perf/x86/amd/power: Do not load AMD power module on !AMD platforms

Pull timer fix from Thomas Gleixner:
 "A single fix for a ~10 years old problem which causes high resolution
  timers to stop after a CPU unplug/plug cycle due to a stale flag in
  the per CPU hrtimer base struct.

  Paul McKenney was hunting this for about a year, but the heisenbug
  nature made it resistant against debug attempts for quite some time"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  hrtimer: Reset hrtimer cpu base proper on CPU hotplug

Pull scheduler fix from Thomas Gleixner:
 "A single bug fix to prevent a subtle deadlock in the scheduler core
  code vs cpu hotplug"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/core: Fix cpu.max vs. cpuhotplug deadlock

Pull perf fixes from Thomas Gleixner:
 "Four patches which all address lock inversions and deadlocks in the
  perf core code and the Intel debug store"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86: Fix perf,x86,cpuhp deadlock
  perf/core: Fix ctx::mutex deadlock
  perf/core: Fix another perf,trace,cpuhp lock inversion
  perf/core: Fix lock inversion between perf,trace,cpuhp

Pull locking fixes from Thomas Gleixner:
 "Two final locking fixes for 4.15:

   - Repair the OWNER_DIED logic in the futex code which got wreckaged
     with the recent fix for a subtle race condition.

   - Prevent the hard lockup detector from triggering when dumping all
     held locks in the system"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  locking/lockdep: Avoid triggering hardlockup from debug_show_all_locks()
  futex: Fix OWNER_DEAD fixup

When ORC support was added for the ftrace_64.S code, an ENDPROC
for function_hook() was missed. This results in the following warning:

  arch/x86/kernel/ftrace_64.o: warning: objtool: .entry.text+0x0: unreachable instruction

Fixes: e2ac83d7 ("x86/ftrace: Fix ORC unwinding from ftrace handlers")
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lkml.kernel.org/r/20180128022150.dqierscqmt3uwwsr@treble

The hrtimer interrupt code contains a hang detection and mitigation
mechanism, which prevents that a long delayed hrtimer interrupt causes a
continous retriggering of interrupts which prevent the system from making
progress. If a hang is detected then the timer hardware is programmed with
a certain delay into the future and a flag is set in the hrtimer cpu base
which prevents newly enqueued timers from reprogramming the timer hardware
prior to the chosen delay. The subsequent hrtimer interrupt after the delay
clears the flag and resumes normal operation.

If such a hang happens in the last hrtimer interrupt before a CPU is
unplugged then the hang_detected flag is set and stays that way when the
CPU is plugged in again. At that point the timer hardware is not armed and
it cannot be armed because the hang_detected flag is still active, so
nothing clears that flag. As a consequence the CPU does not receive hrtimer
interrupts and no timers expire on that CPU which results in RCU stalls and
other malfunctions.

Clear the flag along with some other less critical members of the hrtimer
cpu base to ensure starting from a clean state when a CPU is plugged in.

Thanks to Paul, Sebastian and Anna-Maria for their help to get down to the
root cause of that hard to reproduce heisenbug. Once understood it's
trivial and certainly justifies a brown paperbag.

Fixes: 41d2e494 ("hrtimer: Tune hrtimer_interrupt hang logic")
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Sewior <bigeasy@linutronix.de>
Cc: Anna-Maria Gleixner <anna-maria@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1801261447590.2067@nanos