- 27 May, 2024 8 commits
-
-
Umesh Nerlige Ramappa authored
Note that runtime is also used in the pm context, so it is confusing to use the same name to denote run time of the drm client. Use a more appropriate name for the client utilization. While at it, drop the incorrect multi-lrc comment in the helper description v2: s/show_runtime/show_run_ticks/ (Rodrigo) Signed-off-by:
Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com> Reviewed-by:
Rodrigo Vivi <rodrigo.vivi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240524234744.1352543-1-umesh.nerlige.ramappa@intel.com
-
Thomas Hellström authored
In order to be able to run gpu jobs from reclaim context, move job creation (where allocation takes place) out of the struct xe_migrate::job_mutex, and prime that mutex as reclaim tainted. Jobs that may need to run from reclaim context include CCS metadata extraction at shrinking time. Signed-off-by:
Thomas Hellström <thomas.hellstrom@linux.intel.com> Reviewed-by:
-
Thomas Hellström authored
It's not used anymore. Signed-off-by:
Matthew Brost <matthew.brost@intel.com> Reviewed-by:
-
Thomas Hellström authored
Pre-allocate but don't initialize fences at xe_sched_job_create(), and initialize / arm them instead at xe_sched_job_arm(). This makes it possible to move xe_sched_job_create() with its memory allocation out of any lock that is required for fence initialization, and that may not allow memory allocation under it. Replaces the struct dma_fence_array for parallell jobs with a struct dma_fence_chain, since the former doesn't allow a split-up between allocation and initialization. v2: - Rebase. - Don't always use the first lrc when initializing parallel lrc fences. - Use dma_fence_chain_contained() to access the lrc fences. v4: - Add an assert that job->lrc_seqno == fence->seqno. (Matthew Brost) Signed-off-by:
-
Thomas Hellström authored
Since sometimes a lock is required to initialize a seqno fence, and it might be desirable not to hold that lock while performing memory allocations, split the lrc seqno fence creation up into an allocation phase and an initialization phase. Since lrc seqno fences under the hood are hw_fences, do the same for these and remove the xe_hw_fence_create() function since it is not used anymore. Signed-off-by:
-
Matthew Brost authored
Tightly coupling these seqno presents problems if alternative fences for jobs are used. Decouple these for correctness. v2: - Slightly reword commit message (Thomas) - Make sure the lrc fence ops are used in comparison (Thomas) - Assume seqno is unsigned rather than signed in format string (Thomas) Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com> Signed-off-by:
-
Michal Wajdeczko authored
Each VF is assigned a limited range of the GGTT address space. To ensure that the VF driver does not use GGTT allocations outside of the assigned region, explicitly reserve GGTT space below and above this region when initializing GGTT. Signed-off-by:
Michal Wajdeczko <michal.wajdeczko@intel.com> Reviewed-by:
Michał Winiarski <michal.winiarski@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240527112015.1020-1-michal.wajdeczko@intel.com
-
Michal Wajdeczko authored
Each VF will be assigned with only a limited range of the GGTT address space. Make sure that VF driver will read its own GGTT configuration before starting any GGTT initialization. Signed-off-by:
-
- 24 May, 2024 6 commits
-
-
Michal Wajdeczko authored
While the GMDID registers are not part of the runtime register list shared by the PF driver, we may still return cached values from our VF specific read32() helper function. Signed-off-by:
Matt Roper <matthew.d.roper@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240523192240.844-7-michal.wajdeczko@intel.com
-
Michal Wajdeczko authored
Read and cache value of the GMDID register as part of the config query that VF driver is doing over MMIO. While the VF driver likely already obtained the value of the GMDID register once during the early driver probe, we couldn't cache it then as the GT structures were not ready yet. Cache it now, in case the driver needs it later when the GuC MMIO communication, required to query GMDID from GuC, could be no longer desired as it will be replaced by the CTB communication. While around, assert that we will query GMDID only when applicable. Signed-off-by:
-
Michal Wajdeczko authored
VFs do not have direct access to the GMDID register and must obtain its value from the GuC. Since we need GMDID value very early in the driver probe flow, before we even start the full setup of GT and GuC data structures, we must do some early initializations ourselves. Additionally, since we also need GMDID for the media GT, which isn't created yet, temporarly tweak the root GT type into MEDIA to allow communication with the correct GuC, as only it can provide the value of the media GMDID register. Signed-off-by:
-
Michal Wajdeczko authored
VFs don't have access to the GMDID register and must obtain it value using GuC VF ABI KLV query. Add function for doing that. Signed-off-by:
-
Michal Wajdeczko authored
VF drivers can't access GMD_ID register over MMIO. The value of the GMD_ID register must be queried from GuC. It is available as GLOBAL_CFG_GMD_ID KLV. Signed-off-by:
-
Michal Wajdeczko authored
As part of the its initialization, the VF driver has already obtained a list of the runtime (fuse) register values from the PF driver. When VF driver is attempting to read register that is inaccessible to the VF, use the values from this list instead. Signed-off-by:
-
- 23 May, 2024 12 commits
-
-
John Harrison authored
GuC loading can take longer than it is supposed to for various reasons. So add in the code to cope with that and to report it when it happens. There are also many different reasons why GuC loading can fail, so add in the code for checking for those and for reporting issues in a meaningful manner rather than just hitting a timeout and saying 'fail: status = %x'. Also, remove the 'FIXME' comment about an i915 bug that has never been applicable to Xe! v2: Actually report the requested and granted frequencies rather than showing granted twice (review feedback from Badal). v3: Locally code all the timeout and end condition handling because a helper function is not allowed (review feedback from Lucas/Rodrigo). v4: Add more documentation comments and rename a define to add units (review feedback from Lucas). v5: Fix copy/paste error in xe_mmio_wait32_not (review feedback from Lucas) and rebase (no more return value from guc_wait_ucode). Signed-off-by:
John Harrison <John.C.Harrison@Intel.com> Reviewed-by:
Lucas De Marchi <lucas.demarchi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240518043700.3264362-3-John.C.Harrison@Intel.com
-
John Harrison authored
Other driver code beyond the sysfs interface wants to know about throttling. So make the query function globally accessible. v2: Revert include order change (review feedback from Lucas) v3: Remove '_sysfs' from throttle file names and keep limit query in the same file rather than moving elsewhere (review feedback from Rodrigo). v4: Correct #include while renaming header file (review feedback from Lucas). Signed-off-by:
-
José Roberto de Souza authored
This error capture prints into dmesg HW state when a gpu hang happens. It was useful when we did not had devcoredump, now it is a incompleted version of devcoredump that has potential to flood dmesg. Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: John Harrison <John.C.Harrison@Intel.com> Signed-off-by:
José Roberto de Souza <jose.souza@intel.com> Reviewed-by:
-
José Roberto de Souza authored
Process name help us track what application caused the gpug hang, this is crucial when running several applications at the same time. v2: - handle Xe KMD exec_queues without VM v3: - use get_pid_task() (suggested by Nirmoy) Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Nirmoy Das <nirmoy.das@intel.com> Signed-off-by:
-
Dr. David Alan Gilbert authored
'xe_gt_desc' is unused since commit 1e6c20be ("drm/xe: Drop extra_gts[] declarations and XE_GT_TYPE_REMOTE"). Remove it. Signed-off-by:
Dr. David Alan Gilbert <linux@treblig.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240522175840.382107-1-linux@treblig.orgReviewed-by:
-
Rodrigo Vivi authored
Now that we eliminated all the mem_access get/put with its locking issues from the inner calls of migration, we can allow D3Cold. Enable it when VRAM utilization is lower then 300Mb. On higher utilization we only allow D3hot so we don't increase so much the latency on runtime resume due to the memory restoration. Reviewed-by:
Anshuman Gupta <anshuman.gupta@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240522170105.327472-7-rodrigo.vivi@intel.comSigned-off-by:
-
Rodrigo Vivi authored
GuC reset status is not reliable for this purpose and it is once in a while ending up in a situation of D3Cold, where power_reset is false and without the proper memory restoration the GuC reload and Display will fail to come back from D3Cold. So, let's do a full restoration of everything if we have a risk of losing power, without further optimizations. v2: also remove the gut_in_reset function (Anshuman) Cc: Anshuman Gupta <anshuman.gupta@intel.com> Reviewed-by:
Badal Nilawar <badal.nilawar@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240522170105.327472-6-rodrigo.vivi@intel.comSigned-off-by:
-
Rodrigo Vivi authored
Prepare power-well and DC handling for a full power lost during D3Cold, then sanitize it upon D3->D0. Otherwise we get a bunch of state mismatch. Ideally we could leave DC9 enabled and wouldn't need to move DC9->DC0 on every runtime resume, however, the disable_DC is part of the power-well checks and intrinsic to the dc_off power well. In the future that can be detangled so we can have even bigger power savings. But for now, let's focus on getting a D3Cold, which saves much more power by itself. v2: create new functions to avoid full-suspend-resume path, which would result in a deadlock between xe_gem_fault and the modeset-ioctl. v3: Only avoid the full modeset to avoid the race, for a more robust suspend-resume. Cc: Anshuman Gupta <anshuman.gupta@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Tested-by:
Francois Dugast <francois.dugast@intel.com> Reviewed-by:
-
Rodrigo Vivi authored
In the regular use case scenario, user space will create a VM, and keep it alive for the entire duration of its workload. For the regular desktop cases, it means that the VM is alive even on idle scenarios where display goes off. This is unacceptable since this would entirely block runtime PM indefinitely, blocking deeper Package-C state. This would be a waste drainage of power. Limit the VM protection solely for long-running workloads that are not protected by the scheduler references. By design, run_job for long-running workloads returns NULL and the scheduler drops all the references of it, hence protecting the VM for this case is necessary. v2: Update commit message to a more imperative language and to reflect why the VM protection is really needed. Also add a comment in the code to let the reason visbible. v3: Remove vma_access case and the mentions to mmap. Mmap cases are already protected by the gem page fault. Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com> Cc: Lucas De Marchi <lucas.demarchi@intel.com> Cc: Matthew Brost <matthew.brost@intel.com> Tested-by: -
Rodrigo Vivi authored
Limit the protection only during moments of actual job execution, and introduce protection for guc submit fini, which is currently unprotected due to the absence of exec_queue life protection. In the regular use case scenario, user space will create an exec queue, and keep it alive to reuse that until it is done with that kind of workload. For the regular desktop cases, it means that the exec_queue is alive even on idle scenarios where display goes off. This is unacceptable since this would entirely block runtime PM indefinitely, blocking deeper Package-C state. This would be a waste drainage of power. Cc: Matthew Brost <matthew.brost@intel.com> Tested-by:
-
Rodrigo Vivi authored
Let's be clear on what it is actually doing and align with xe_pm_runtime_get_if_active doc style. Tested-by:
-
Rodrigo Vivi authored
Current callers of this function are already taking the result to a boolean and using in an if. It might be a problem because current function might return negative error codes on failure, without increasing the reference counter. In this scenario we could end up with extra 'put' call ending in unbalanced scenarios. Let's fix it, while aligning with the current xe_pm_get_if_in_use style. Tested-by:
-
- 22 May, 2024 14 commits
-
-
Niranjana Vishwanathapura authored
Release the submission_state lock if alloc_guc_id() fails. v2: Add Fixes tag and CC stable kernel Fixes: dd08ebf6 ("drm/xe: Introduce a new DRM driver for Intel GPUs") Cc: <stable@vger.kernel.org> # v6.8+ Signed-off-by:
Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com> Reviewed-by:
Nirmoy Das <nirmoy.das@intel.com> Reviewed-by:
-
Michal Wajdeczko authored
When running in execlist mode (using force_execlist=1 modparam) we incorrectly select the error path in xe_uc_init(), leading to an unwanted error message like this: [ ] xe 0000:00:00.0: [drm] *ERROR* GT0: Failed to initialize uC (0000000000000000) Fix that by doing early return like we do in other similar cases. Signed-off-by:
Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240521114857.712-1-michal.wajdeczko@intel.com
-
Matthew Auld authored
i915 display calls this when releasing the drm_device, match this also in xe by using drmm. intel_display_device_remove() is freeing purely software state for the drm_device. v2: fix build error Signed-off-by:
Matthew Auld <matthew.auld@intel.com> Cc: Andrzej Hajda <andrzej.hajda@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by:
Andrzej Hajda <andrzej.hajda@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240522102143.128069-36-matthew.auld@intel.com
-
Matthew Auld authored
Unclear why we call this twice. Signed-off-by:
-
Matthew Auld authored
Match the i915 display handling here with calling both no_irq and noaccel when removing the device. Signed-off-by:
-
Matthew Auld authored
Set our various mmio mappings to NULL. This should make it easier to catch something rogue trying to mess with mmio after device removal. For example, we might unmap everything and then start hitting some mmio address which has already been unmamped by us and then remapped by something else, causing all kinds of carnage. Signed-off-by:
-
Matthew Auld authored
Not valid to touch mmio once the device is removed, so make sure we unmap on removal and not just when driver instance goes away. Also set the mmio pointers to NULL to hopefully catch such issues more easily. Signed-off-by:
-
Matthew Auld authored
No need to hand roll the onion unwind here, just move gt_remove over to devm which will already have the correct ordering. Signed-off-by:
-
Matthew Auld authored
Have a cleaner separation between hw vs sw. v2: Fix missing return Signed-off-by:
-
Matthew Auld authored
Here we are using drmm to ensure we release the coredump when unloading the module, however the coredump is very much tied to the struct device underneath. We can see this when we hotunplug the device, for which we have already got a coredump attached. In such a case the coredump still remains and adding another is not possible. However we still register the release action via xe_driver_devcoredump_fini(), so in effect two or more releases for one dump. The other consideration is that the coredump state is embedded in the xe_driver instance, so technically once the drmm release action fires we might free the coredumpe state from a different driver instance, assuming we have two release actions and they can race. Rather use devm here to remove the coredump when the device is released. References: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/1679Signed-off-by:
-
Matthew Auld authored
Disable GuC submission when removing the device. Signed-off-by:
-
Matthew Auld authored
Should be called when driver is removed, not when this particular driver instance is destroyed. Signed-off-by:
-
Matthew Auld authored
Makes sense to trigger this when the device is removed. Signed-off-by:
-
Matthew Auld authored
Make it clear that is about cleaning up the HW/FW side, and not software state. Signed-off-by:
-
