- 23 Jan, 2020 15 commits
-
-
Tony Lindgren authored
I've tested that the interconnect target module enables and idles just fine when probed with ti-sysc with PM runtime control via sys: # echo on > $(find /sys -name control | grep \/5600) # rwmem 0x5600fe00 # OCP Revision 0x5600fe00 = 0x40000000 # echo auto > $(find /sys -name control | grep \/5600) Cc: "H. Nikolaus Schaller" <hns@goldelico.com> Cc: Robert Nelson <robertcnelson@gmail.com> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Tony Lindgren authored
The following can be tested via sysfs with the following to ensure the SGX module gets enabled and disabled properly: # echo on > /sys/bus/platform/devices/5600fe00.target-module/power/control # rwmem 0x5600fe00 # revision register 0x5600fe00 = 0x40000000 # echo auto > /sys/bus/platform/devices/5600fe00.target-module/power/control # rwmem 0x5000fe00 Bus error Note that this patch depends on the PRM rstctrl driver that has been recently posted. If the child device driver(s) need to prevent rstctrl reset on PM runtime suspend, the drivers need to increase the usecount for the shared rstctrl reset that can be mapped also for the child device(s) or accessed via dev->parent. Cc: Adam Ford <aford173@gmail.com> Cc: Filip Matijević <filip.matijevic.pz@gmail.com> Cc: "H. Nikolaus Schaller" <hns@goldelico.com> Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com> Cc: moaz korena <moaz@korena.xyz> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com> Cc: Philipp Rossak <embed3d@gmail.com> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Tony Lindgren authored
-
Benoit Parrot authored
Add VPE node as a child of l4 interconnect in order for it to probe using ti-sysc. Signed-off-by: Benoit Parrot <bparrot@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Benoit Parrot authored
Add clkctrl nodes for VPE module. Note that because of the current dts node name dependency for mapping to clock domain, we must still use "vpe-clkctrl@" naming instead of generic "clock@" naming for the node. And because of this, it's probably best to apply the dts node addition together along with the other clock changes. Signed-off-by: Benoit Parrot <bparrot@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Benoit Parrot authored
Add VPFE device nodes entries. Add OmniVision OV2659 sensor device nodes and linkage. Since Rev1.2a on this board the sensor source clock (xvclk) has a dedicated 12Mhz oscillator instead of using clkout1. Add 'audio_mstrclk' fixed clock object to represent it. Signed-off-by: Benoit Parrot <bparrot@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Benoit Parrot authored
Add VPFE device nodes entries. Add OmniVision OV2659 sensor device nodes and linkage. The sensor clock (xvclk) is sourced from clkout1. Add clock entries to properly select clkout1 and set its parent clock to sys_clkin_ck. Signed-off-by: Benoit Parrot <bparrot@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Tero Kristo authored
clkout1 clock node and its generation tree was missing. Add this based on the data on TRM and PRCM functional spec. commit 664ae1ab ("ARM: dts: am43xx: add clkctrl nodes") effectively reverted this commit 8010f13a ("ARM: dts: am43xx: add support for clkout1 clock") which is needed for the ov2659 camera sensor clock definition hence it is being re-applied here. Note that because of the current dts node name dependency for mapping to clock domain, we must still use "clkout1-*ck" naming instead of generic "clock@" naming for the node. And because of this, it's probably best to apply the dts node addition together along with the other clock changes. Fixes: 664ae1ab ("ARM: dts: am43xx: add clkctrl nodes") Signed-off-by: Tero Kristo <t-kristo@ti.com> Tested-by: Benoit Parrot <bparrot@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Benoit Parrot <bparrot@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Benoit Parrot authored
Add device nodes for CSI2 camera board OV5640. Add the CAL port nodes with the necessary linkage to the ov5640 nodes. Signed-off-by: Benoit Parrot <bparrot@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Benoit Parrot authored
Add the required dtsi node to support the Camera Adaptation Layer (CAL) for the DRA76 family of devices. Signed-off-by: Benoit Parrot <bparrot@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Benoit Parrot authored
Add device nodes for CSI2 camera board OV5640. Add the CAL port nodes with the necessary linkage to the ov5640 nodes. Signed-off-by: Benoit Parrot <bparrot@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Benoit Parrot authored
This patch adds the required dtsi node to support the Camera Adaptation Layer (CAL) for the DRA72 family of devices. Signed-off-by: Benoit Parrot <bparrot@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Benoit Parrot authored
Add CAM nodes as a child of l4 interconnect in order for it to probe using ti-sysc. Signed-off-by: Benoit Parrot <bparrot@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Benoit Parrot authored
Both CAL and VIP rely on this clock domain. But CAL DPHY require LVDSRX_96M_GFCLK to be active. When this domain is set to HWSUP the LVDSRX_96M_GFCLK is on;y active when VIP1 clock is also active. If only CAL on DRA72x (which uses the VIP2 clkctrl) probes the CAM domain is enabled but the LVDSRX_96M_GFCLK is left gated. Since LVDSRX_96M_GFCLK is sourcing the input clock to the DPHY then actual frame capture cannot start as the phy are inactive. So we either have to also enabled VIP1 even if we don't intend on using it or we need to set the CAM domain to use SWSUP only. This patch implements the latter. Signed-off-by: Benoit Parrot <bparrot@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Benoit Parrot authored
Add clkctrl nodes for CAM domain. Note that because of the current dts node name dependency for mapping to clock domain, we must still use "cam-clkctrl@" naming instead of generic "clock@" naming for the node. And because of this, it's probably best to apply the dts node addition together along with the other clock changes. Signed-off-by: Benoit Parrot <bparrot@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
- 20 Jan, 2020 7 commits
-
-
Tony Lindgren authored
We currently have a hidden dependency to the device tree node name for the clkctrl clocks. Instead of using standard node name like "clock", we must use "l4-per-clkctrl" type naming so the clock driver can find the associated clock domain. Further, if "clk" is specified for a clock node name, the driver sets TI_CLK_CLKCTRL_COMPAT flag that uses different logic for the clock name based on the parent node name for the all the clkctrl clocks for the SoC. If the clock node naming dependency is not understood, the related clockdomain is not found, or a wrong one can get used if a clock manager has multiple clock domains. As each clkctrl instance represents a single clock domain, let's allow using domain specific compatible names to specify the clock domain. This simplifies things and removes the hidden dependency to the node name. And then later on, after the node names have been standardized, we can drop the related code for parsing the node names. Let's also update the binding to use standard "clock" node naming instead of "clk" and add the missing description for reg. Cc: devicetree@vger.kernel.org Cc: Rob Herring <robh+dt@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Rob Herring <robh@kernel.org> Acked-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Tero Kristo <t-kristo@ti.com>
-
Tony Lindgren authored
This is similar to what we have for omap5 except the gpu_cm address is different, the mux clocks have one more source option, and there's no divider clock. Note that because of the current dts node name dependency for mapping to clock domain, we must still use "gpu-clkctrl@" naming instead of generic "clock@" naming for the node. And because of this, it's probably best to apply the dts node addition together along with the other clock changes. For accessing the GPU, we also need to configure the interconnect target module for GPU similar to what we have for omap5, I'll send that change separately. Cc: Benoit Parrot <bparrot@ti.com> Cc: "H. Nikolaus Schaller" <hns@goldelico.com> Cc: Robert Nelson <robertcnelson@gmail.com> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Tero Kristo <t-kristo@ti.com>
-
Tony Lindgren authored
Looks like we're missing AESS clock for omap5. This is similar to what omap4 has. Cc: H. Nikolaus Schaller <hns@goldelico.com> Cc: Matthijs van Duin <matthijsvanduin@gmail.com> Cc: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tero Kristo <t-kristo@ti.com>
-
Grygorii Strashko authored
The parent clk for gmac clk ctrl has to be gmac_main_clk (125MHz) instead of dpll_gmac_ck (1GHz). This is caused incorrect CPSW MDIO operation. Hence, fix it. Fixes: dffa9051 ('clk: ti: dra7: add new clkctrl data') Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Tero Kristo <t-kristo@ti.com>
-
Benoit Parrot authored
Add clkctrl data for VPE. Signed-off-by: Benoit Parrot <bparrot@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Rob Herring <robh@kernel.org> Acked-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Tero Kristo <t-kristo@ti.com>
-
Benoit Parrot authored
Add clkctrl data for CAM domain. Signed-off-by: Benoit Parrot <bparrot@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Rob Herring <robh@kernel.org> Acked-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Tero Kristo <t-kristo@ti.com>
-
Peter Ujfalusi authored
Most of the clock related dt-binding header files are located in dt-bindings/clock folder. It would be good to keep all the similar header files at a single location. Suggested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Tero Kristo <t-kristo@ti.com>
-
- 13 Jan, 2020 2 commits
-
-
André Hentschel authored
This is the first generation Amazon Echo from 2016. Audio support is not yet implemented. Signed-off-by: André Hentschel <nerv@dawncrow.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
André Hentschel authored
DM3730 is considered as omap36xx.dtsi, while the rest has: DM3730 | DM3725 | AM3715 | AM3703 IVA X | X | | SGX X | | X | Where X is "supported" Signed-off-by: André Hentschel <nerv@dawncrow.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
- 12 Dec, 2019 6 commits
-
-
Jyri Sarha authored
Add support for OSD9616P0899-10 96x16 passive matrix display. The pre-charge period parameters are taken form a OSD9616P0899-10 document, but the display works fine with the default values too. Signed-off-by: Jyri Sarha <jsarha@ti.com> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Jyri Sarha authored
Move to use the new drm panel support in tilcdc together with added "newhaven,nhd-4.3-480272ef-atxl"-panel support in drm panel-simple. Signed-off-by: Jyri Sarha <jsarha@ti.com> Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Jyri Sarha authored
Move to use the new drm panel support in tilcdc together with added "tfc,s9700rtwv43tr-01b"-panel support in drm panel-simple. Signed-off-by: Jyri Sarha <jsarha@ti.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Grygorii Strashko authored
Rename davinci_mdio DT node "ethernet"->"mdio" This fixes the following DT schemas check errors: am3517-craneboard.dt.yaml: ethernet@5c030000: $nodename:0: 'ethernet@5c030000' does not match '^mdio(@.*)?' Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Tomi Valkeinen authored
AM571x/AM572x/AM574x IDK base boards have HDMI output. Add DT nodes to am57xx-idk-common.dtsi to enable HDMI. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Tomi Valkeinen authored
Add DRA76 EVM HDMI output for the base board. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
- 08 Dec, 2019 10 commits
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds authored
Pull networking fixes from David Miller: 1) More jumbo frame fixes in r8169, from Heiner Kallweit. 2) Fix bpf build in minimal configuration, from Alexei Starovoitov. 3) Use after free in slcan driver, from Jouni Hogander. 4) Flower classifier port ranges don't work properly in the HW offload case, from Yoshiki Komachi. 5) Use after free in hns3_nic_maybe_stop_tx(), from Yunsheng Lin. 6) Out of bounds access in mqprio_dump(), from Vladyslav Tarasiuk. 7) Fix flow dissection in dsa TX path, from Alexander Lobakin. 8) Stale syncookie timestampe fixes from Guillaume Nault. [ Did an evil merge to silence a warning introduced by this pull - Linus ] * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits) r8169: fix rtl_hw_jumbo_disable for RTL8168evl net_sched: validate TCA_KIND attribute in tc_chain_tmplt_add() r8169: add missing RX enabling for WoL on RTL8125 vhost/vsock: accept only packets with the right dst_cid net: phy: dp83867: fix hfs boot in rgmii mode net: ethernet: ti: cpsw: fix extra rx interrupt inet: protect against too small mtu values. gre: refetch erspan header from skb->data after pskb_may_pull() pppoe: remove redundant BUG_ON() check in pppoe_pernet tcp: Protect accesses to .ts_recent_stamp with {READ,WRITE}_ONCE() tcp: tighten acceptance of ACKs not matching a child socket tcp: fix rejected syncookies due to stale timestamps lpc_eth: kernel BUG on remove tcp: md5: fix potential overestimation of TCP option space net: sched: allow indirect blocks to bind to clsact in TC net: core: rename indirect block ingress cb function net-sysfs: Call dev_hold always in netdev_queue_add_kobject net: dsa: fix flow dissection on Tx path net/tls: Fix return values to avoid ENOTSUPP net: avoid an indirect call in ____sys_recvmsg() ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsiLinus Torvalds authored
Pull more SCSI updates from James Bottomley: "Eleven patches, all in drivers (no core changes) that are either minor cleanups or small fixes. They were late arriving, but still safe for -rc1" * tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: scsi: MAINTAINERS: Add the linux-scsi mailing list to the ISCSI entry scsi: megaraid_sas: Make poll_aen_lock static scsi: sd_zbc: Improve report zones error printout scsi: qla2xxx: Fix qla2x00_request_irqs() for MSI scsi: qla2xxx: unregister ports after GPN_FT failure scsi: qla2xxx: fix rports not being mark as lost in sync fabric scan scsi: pm80xx: Remove unused include of linux/version.h scsi: pm80xx: fix logic to break out of loop when register value is 2 or 3 scsi: scsi_transport_sas: Fix memory leak when removing devices scsi: lpfc: size cpu map by last cpu id set scsi: ibmvscsi_tgt: Remove unneeded variable rc
-
git://git.samba.org/sfrench/cifs-2.6Linus Torvalds authored
Pull cifs fixes from Steve French: "Nine cifs/smb3 fixes: - one fix for stable (oops during oplock break) - two timestamp fixes including important one for updating mtime at close to avoid stale metadata caching issue on dirty files (also improves perf by using SMB2_CLOSE_FLAG_POSTQUERY_ATTRIB over the wire) - two fixes for "modefromsid" mount option for file create (now allows mode bits to be set more atomically and accurately on create by adding "sd_context" on create when modefromsid specified on mount) - two fixes for multichannel found in testing this week against different servers - two small cleanup patches" * tag '5.5-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6: smb3: improve check for when we send the security descriptor context on create smb3: fix mode passed in on create for modetosid mount option cifs: fix possible uninitialized access and race on iface_list cifs: Fix lookup of SMB connections on multichannel smb3: query attributes on file close smb3: remove unused flag passed into close functions cifs: remove redundant assignment to pointer pneg_ctxt fs: cifs: Fix atime update check vs mtime CIFS: Fix NULL-pointer dereference in smb2_push_mandatory_locks
-
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfsLinus Torvalds authored
Pull misc vfs cleanups from Al Viro: "No common topic, just three cleanups". * 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: make __d_alloc() static fs/namespace: add __user to open_tree and move_mount syscalls fs/fnctl: fix missing __user in fcntl_rw_hint()
-
git://github.com/jonmason/ntbLinus Torvalds authored
Pull NTB update from Jon Mason: "Just a simple patch to add a new Hygon Device ID to the AMD NTB device driver" * tag 'ntb-5.5' of git://github.com/jonmason/ntb: NTB: Add Hygon Device ID
-
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/inputLinus Torvalds authored
Pull more input updates from Dmitry Torokhov: - fixups for Synaptics RMI4 driver - a quirk for Goodinx touchscreen on Teclast tablet - a new keycode definition for activating privacy screen feature found on a few "enterprise" laptops - updates to snvs_pwrkey driver - polling uinput device for writing (which is always allowed) now works * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: synaptics-rmi4 - don't increment rmiaddr for SMBus transfers Input: synaptics-rmi4 - re-enable IRQs in f34v7_do_reflash Input: goodix - add upside-down quirk for Teclast X89 tablet Input: add privacy screen toggle keycode Input: uinput - fix returning EPOLLOUT from uinput_poll Input: snvs_pwrkey - remove gratuitous NULL initializers Input: snvs_pwrkey - send key events for i.MX6 S, DL and Q
-
git://git.kernel.org/pub/scm/fs/xfs/xfs-linuxLinus Torvalds authored
Pull iomap fixes from Darrick Wong: "Fix a race condition and a use-after-free error: - Fix a UAF when reporting writeback errors - Fix a race condition when handling page uptodate on fragmented file with blocksize < pagesize" * tag 'iomap-5.5-merge-14' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux: iomap: stop using ioend after it's been freed in iomap_finish_ioend() iomap: fix sub-page uptodate handling
-
git://git.kernel.org/pub/scm/fs/xfs/xfs-linuxLinus Torvalds authored
Pull xfs fixes from Darrick Wong: "Fix a couple of resource management errors and a hang: - fix a crash in the log setup code when log mounting fails - fix a hang when allocating space on the realtime device - fix a block leak when freeing space on the realtime device" * tag 'xfs-5.5-merge-17' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux: xfs: fix mount failure crash on invalid iclog memory access xfs: don't check for AG deadlock for realtime files in bunmapi xfs: fix realtime file data space leak
-
git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linuxLinus Torvalds authored
Pull orangefs update from Mike Marshall: "orangefs: posix open permission checking... Orangefs has no open, and orangefs checks file permissions on each file access. Posix requires that file permissions be checked on open and nowhere else. Orangefs-through-the-kernel needs to seem posix compliant. The VFS opens files, even if the filesystem provides no method. We can see if a file was successfully opened for read and or for write by looking at file->f_mode. When writes are flowing from the page cache, file is no longer available. We can trust the VFS to have checked file->f_mode before writing to the page cache. The mode of a file might change between when it is opened and IO commences, or it might be created with an arbitrary mode. We'll make sure we don't hit EACCES during the IO stage by using UID 0" [ This is "posixish", but not a great solution in the long run, since a proper secure network server shouldn't really trust the client like this. But proper and secure POSIX behavior requires an open method and a resulting cookie for IO of some kind, or similar. - Linus ] * tag 'for-linus-5.5-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux: orangefs: posix open permission checking...
-