imx8mm evk board usb1 port does not support over current detection,
so disable it.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Do not write the 'reg' of multiple groups of data into a uint32 array,
use <> to separate them. Otherwise, the errors similar to the following
will be reported by reg.yaml.

arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dt.yaml:
 soc: pcie@3400000:reg:0: \
 [0, 54525952, 0, 1048576, 64, 0, 0, 8192] is too long
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

enet_clk_ref actually is sourced from internal gpr clocks
which needs a default rate. Also update enet lpcg clock
output names to be more straightforward.

Cc: Abel Vesa <abel.vesa@nxp.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This fixes multiple issues with the current non-existent PCIe clock setup:

The controller can run at up to 250MHz, so use a parent that provides this
clock.

The PHY needs an exact 100MHz reference clock to function if the PCIe
refclock is not fed in via the refclock pads. While this mode is not
supported (yet) in the driver it doesn't hurt to make sure we are
providing a clock with the right rate.

The AUX clock is specified to have a maximum clock rate of 10MHz. So
the current setup, which drives it straight from the 25MHz oscillator is
actually overclocking the AUX input.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

DMA addressing capabilities on i.MX8MN are limited by the interconnect,
same as on i.MX8MQ. Add dma-ranges to the the peripheral bus to let
the kernel know about this.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

DMA addressing capabilities on i.MX8MM are limited by the interconnect,
same as on i.MX8MQ. Add dma-ranges to the the peripheral bus to let
the kernel know about this.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Currently all PCIE windows point to bus address 0x0, which does not match
the values obtained from hardware during EA.
Replace those values with CPU addresses, since in reality we
have a 1:1 mapping between the two.
Signed-off-by: Kornel Duleba <mindal@semihalf.com>
Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The PMIC throws an errors because the clock isn't assigned to it.
Fix this by assigning the clocks info.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

On LS2088A-RDB board, if the spi-fsl-dspi driver is built as module
then its probe fails with the following warning:

[   10.471363] couldn't get idr
[   10.471381] WARNING: CPU: 4 PID: 488 at drivers/spi/spi.c:2689 spi_register_controller+0x73c/0x8d0
...
[   10.471651] fsl-dspi 2100000.spi: Problem registering DSPI ctlr
[   10.471708] fsl-dspi: probe of 2100000.spi failed with error -16

Reason for the failure is that bus-num property is set for dspi node.
However, bus-num property is not set for the qspi node. If probe for
spi-fsl-qspi happens first then id 0 is dynamically allocated to it.
Call to spi_register_controller() from spi-fsl-dspi driver then fails.
Since commit 29d2daf2 ("spi: spi-fsl-dspi: Make bus-num property
optional") bus-num property is optional. Remove bus-num property from
dspi node to fix the issue.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ls1012a-freeway board contains a M.2 2230 slot. Update the status of
pcei1 node to okay so that the pcie controller can be probed.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Enable EQOS ethernet on i.MX8MP EVK board.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

On i.MX8MP, there is no audio ipg clock, so remove the wrong reference
to this clock in dts file.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Both 1.8v and 3.3v power supplies can be used by i.MX8MQ PCIe PHY.
In default, the PCIE_VPH voltage is suggested to be 1.8v refer to data
sheet. When PCIE_VPH is supplied by 3.3v in the HW schematic design,
the VREG_BYPASS bits of GPR registers should be cleared from default
value 1b'1 to 1b'0. Thus, the internal 3v3 to 1v8 translator would be
turned on.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The i.MX8MM reference manual shows there are two spba busses.
SPBA1 handles much of the serial interfaces, and SPBA2 covers much
of the audio.

Add both of them.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The i.MX8MN has an SPBA bus which covers much of the audio, but
there is a second SPBA bus which covers many of the serial interfaces
like SPI and UARTs currently missing from the device tree. The reference
manual calls the bus handling the audio peripherals SPBA2, and the bus
handling the serial peripherals is called SPBA1.

Rename the existing spba bus to spba2 and add spba1.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support of the lt8912b in the DTB.
This adds the support of the DB_DSIHD daugther board from
Boundary Devices.
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the description for the USB host port.
This port is linked to a resettable USB HUB so handle
this reset signal with a GPIO hog.
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the description for the USB OTG port.
The OTG port uses a dedicated regulator for vbus.
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

enable the mt25qu256aba spi nor on the imx8mp-phycore-som.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

add node for the flexspi modul on imx8mp.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The Gateworks GW7901 is an ARM based single board computer (SBC)
featuring:
 - i.MX8M Mini SoC
 - LPDDR4 DRAM
 - eMMC FLASH
 - SPI FRAM
 - Gateworks System Controller (GSC)
 - Atmel ATECC Crypto Authentication
 - USB 2.0
 - Microchip GbE Switch
 - Multiple multi-protocol RS232/RS485/RS422 Serial ports
 - onboard 802.11ac WiFi / BT
 - microSD socket
 - miniPCIe socket with PCIe, USB 2.0 and dual SIM sockets
 - Wide range DC power input
 - 802.3at PoE
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

optee node was disabled by default, enabling it for ls1028a-rdb.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Sahil Malhotra <sahil.malhotra@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The imx8mp-evk uses an PCA9450C as PMIC that supplies various
regulators.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Commit b9d79e4c ("fbmem: Mark proc_fb_seq_ops as __maybe_unused")
places the '__maybe_unused' in an entirely incorrect location between
the "struct" keyword and the structure name.

It's a wonder that gcc accepts that silently, but clang quite reasonably
warns about it:

    drivers/video/fbdev/core/fbmem.c:736:21: warning: attribute declaration must precede definition [-Wignored-attributes]
    static const struct __maybe_unused seq_operations proc_fb_seq_ops = {
                        ^

Fix it.

Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull drm fixes from Dave Airlie:
 "Bit later than usual, I queued them all up on Friday then promptly
  forgot to write the pull request email. This is mainly amdgpu fixes,
  with some radeon/msm/fbdev and one i915 gvt fix thrown in.

  amdgpu:
   - MPO hang workaround
   - Fix for concurrent VM flushes on vega/navi
   - dcefclk is not adjustable on navi1x and newer
   - MST HPD debugfs fix
   - Suspend/resumes fixes
   - Register VGA clients late in case driver fails to load
   - Fix GEM leak in user framebuffer create
   - Add support for polaris12 with 32 bit memory interface
   - Fix duplicate cursor issue when using overlay
   - Fix corruption with tiled surfaces on VCN3
   - Add BO size and stride check to fix BO size verification

  radeon:
   - Fix off-by-one in power state parsing
   - Fix possible memory leak in power state parsing

  msm:
   - NULL ptr dereference fix

  fbdev:
   - procfs disabled warning fix

  i915:
   - gvt: Fix a possible division by zero in vgpu display rate
     calculation"

* tag 'drm-next-2021-05-10' of git://anongit.freedesktop.org/drm/drm:
  drm/amdgpu: Use device specific BO size & stride check.
  drm/amdgpu: Init GFX10_ADDR_CONFIG for VCN v3 in DPG mode.
  drm/amd/pm: initialize variable
  drm/radeon: Avoid power table parsing memory leaks
  drm/radeon: Fix off-by-one power_state index heap overwrite
  drm/amd/display: Fix two cursor duplication when using overlay
  drm/amdgpu: add new MC firmware for Polaris12 32bit ASIC
  fbmem: Mark proc_fb_seq_ops as __maybe_unused
  drm/msm/dpu: Delete bonkers code
  drm/i915/gvt: Prevent divided by zero when calculating refresh rate
  amdgpu: fix GEM obj leak in amdgpu_display_user_framebuffer_create
  drm/amdgpu: Register VGA clients after init can no longer fail
  drm/amdgpu: Handling of amdgpu_device_resume return value for graceful teardown
  drm/amdgpu: fix r initial values
  drm/amd/display: fix wrong statement in mst hpd debugfs
  amdgpu/pm: set pp_dpm_dcefclk to readonly on NAVI10 and newer gpus
  amdgpu/pm: Prevent force of DCEFCLK on NAVI10 and SIENNA_CICHLID
  drm/amdgpu: fix concurrent VM flushes on Vega/Navi v2
  drm/amd/display: Reject non-zero src_y and src_x for video planes

Pull block fix from Jens Axboe:
 "Turns out the bio max size change still has issues, so let's get it
  reverted for 5.13-rc1. We'll shake out the issues there and defer it
  to 5.14 instead"

* tag 'block-5.13-2021-05-09' of git://git.kernel.dk/linux-block:
  Revert "bio: limit bio max size"

Pull cifs fixes from Steve French:
 "Three small SMB3 chmultichannel related changesets (also for stable)
  from the SMB3 test event this week.

  The other fixes are still in review/testing"

* tag '5.13-rc-smb3-part3' of git://git.samba.org/sfrench/cifs-2.6:
  smb3: if max_channels set to more than one channel request multichannel
  smb3: do not attempt multichannel to server which does not support it
  smb3: when mounting with multichannel include it in requested capabilities

Pull scheduler fixes from Thomas Gleixner:
 "A set of scheduler updates:

   - Prevent PSI state corruption when schedule() races with cgroup
     move.

     A recent commit combined two PSI callbacks to reduce the number of
     cgroup tree updates, but missed that schedule() can drop rq::lock
     for load balancing, which opens the race window for
     cgroup_move_task() which then observes half updated state.

     The fix is to solely use task::ps_flags instead of looking at the
     potentially mismatching scheduler state

   - Prevent an out-of-bounds access in uclamp caused bu a rounding
     division which can lead to an off-by-one error exceeding the
     buckets array size.

   - Prevent unfairness caused by missing load decay when a task is
     attached to a cfs runqueue.

     The old load of the task was attached to the runqueue and never
     removed. Fix it by enforcing the load update through the hierarchy
     for unthrottled run queue instances.

   - A documentation fix fot the 'sched_verbose' command line option"

* tag 'sched-urgent-2021-05-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/fair: Fix unfairness caused by missing load decay
  sched: Fix out-of-bound access in uclamp
  psi: Fix psi state corruption when schedule() races with cgroup move
  sched,doc: sched_debug_verbose cmdline should be sched_verbose

Pull locking fixes from Thomas Gleixner:
 "A set of locking related fixes and updates:

   - Two fixes for the futex syscall related to the timeout handling.

     FUTEX_LOCK_PI does not support the FUTEX_CLOCK_REALTIME bit and
     because it's not set the time namespace adjustment for clock
     MONOTONIC is applied wrongly.

     FUTEX_WAIT cannot support the FUTEX_CLOCK_REALTIME bit because its
     always a relative timeout.

   - Cleanups in the futex syscall entry points which became obvious
     when the two timeout handling bugs were fixed.

   - Cleanup of queued_write_lock_slowpath() as suggested by Linus

   - Fixup of the smp_call_function_single_async() prototype"

* tag 'locking-urgent-2021-05-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  futex: Make syscall entry points less convoluted
  futex: Get rid of the val2 conditional dance
  futex: Do not apply time namespace adjustment on FUTEX_LOCK_PI
  Revert 337f1304 ("futex: Allow FUTEX_CLOCK_REALTIME with FUTEX_WAIT op")
  locking/qrwlock: Cleanup queued_write_lock_slowpath()
  smp: Fix smp_call_function_single_async prototype

Pull x86 perf fix from Borislav Petkov:
 "Handle power-gating of AMD IOMMU perf counters properly when they are
  used"

* tag 'perf_urgent_for_v5.13_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/events/amd/iommu: Fix invalid Perf result due to IOMMU PMC power-gating

Pull x86 fixes from Borislav Petkov:
 "A bunch of things accumulated for x86 in the last two weeks:

   - Fix guest vtime accounting so that ticks happening while the guest
     is running can also be accounted to it. Along with a consolidation
     to the guest-specific context tracking helpers.

   - Provide for the host NMI handler running after a VMX VMEXIT to be
     able to run on the kernel stack correctly.

   - Initialize MSR_TSC_AUX when RDPID is supported and not RDTSCP (virt
     relevant - real hw supports both)

   - A code generation improvement to TASK_SIZE_MAX through the use of
     alternatives

   - The usual misc and related cleanups and improvements"

* tag 'x86_urgent_for_v5.13_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  KVM: x86: Consolidate guest enter/exit logic to common helpers
  context_tracking: KVM: Move guest enter/exit wrappers to KVM's domain
  context_tracking: Consolidate guest enter/exit wrappers
  sched/vtime: Move guest enter/exit vtime accounting to vtime.h
  sched/vtime: Move vtime accounting external declarations above inlines
  KVM: x86: Defer vtime accounting 'til after IRQ handling
  context_tracking: Move guest exit vtime accounting to separate helpers
  context_tracking: Move guest exit context tracking to separate helpers
  KVM/VMX: Invoke NMI non-IST entry instead of IST entry
  x86/cpu: Remove write_tsc() and write_rdtscp_aux() wrappers
  x86/cpu: Initialize MSR_TSC_AUX if RDTSCP *or* RDPID is supported
  x86/resctrl: Fix init const confusion
  x86: Delete UD0, UD1 traces
  x86/smpboot: Remove duplicate includes
  x86/cpu: Use alternative to generate the TASK_SIZE_MAX constant

This reverts commit cd2c7545.

Alex reports that the commit causes corruption with LUKS on ext4. Revert
it for now so that this can be investigated properly.

Link: https://lore.kernel.org/linux-block/1620493841.bxdq8r5haw.none@localhost/Reported-by: Alex Xu (Hello71) <alex_y_xu@yahoo.ca>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Pull RISC-V fixes from Palmer Dabbelt:

 - A fix to avoid over-allocating the kernel's mapping on !MMU systems,
   which could lead to up to 2MiB of lost memory

 - The SiFive address extension errata only manifest on rv64, they are
   now disabled on rv32 where they are unnecessary

 - A pair of late-landing cleanups

* tag 'riscv-for-linus-5.13-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  riscv: remove unused handle_exception symbol
  riscv: Consistify protect_kernel_linear_mapping_text_rodata() use
  riscv: enable SiFive errata CIP-453 and CIP-1200 Kconfig only if CONFIG_64BIT=y
  riscv: Only extend kernel reservation if mapped read-only

intel_dp_check_mst_status() uses a 14-byte array to read the DPRX Event
Status Indicator data, but then passes that buffer at offset 10 off as
an argument to drm_dp_channel_eq_ok().

End result: there are only 4 bytes remaining of the buffer, yet
drm_dp_channel_eq_ok() wants a 6-byte buffer.  gcc-11 correctly warns
about this case:

  drivers/gpu/drm/i915/display/intel_dp.c: In function ‘intel_dp_check_mst_status’:
  drivers/gpu/drm/i915/display/intel_dp.c:3491:22: warning: ‘drm_dp_channel_eq_ok’ reading 6 bytes from a region of size 4 [-Wstringop-overread]
   3491 |                     !drm_dp_channel_eq_ok(&esi[10], intel_dp->lane_count)) {
        |                      ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
  drivers/gpu/drm/i915/display/intel_dp.c:3491:22: note: referencing argument 1 of type ‘const u8 *’ {aka ‘const unsigned char *’}
  In file included from drivers/gpu/drm/i915/display/intel_dp.c:38:
  include/drm/drm_dp_helper.h:1466:6: note: in a call to function ‘drm_dp_channel_eq_ok’
   1466 | bool drm_dp_channel_eq_ok(const u8 link_status[DP_LINK_STATUS_SIZE],
        |      ^~~~~~~~~~~~~~~~~~~~
       6:14 elapsed

This commit just extends the original array by 2 zero-initialized bytes,
avoiding the warning.

There may be some underlying bug in here that caused this confusion, but
this is at least no worse than the existing situation that could use
random data off the stack.

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull more SCSI updates from James Bottomley:
 "This is a set of minor fixes in various drivers (qla2xxx, ufs,
  scsi_debug, lpfc) one doc fix and a fairly large update to the fnic
  driver to remove the open coded iteration functions in favour of the
  scsi provided ones"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: fnic: Use scsi_host_busy_iter() to traverse commands
  scsi: fnic: Kill 'exclude_id' argument to fnic_cleanup_io()
  scsi: scsi_debug: Fix cmd_per_lun, set to max_queue
  scsi: ufs: core: Narrow down fast path in system suspend path
  scsi: ufs: core: Cancel rpm_dev_flush_recheck_work during system suspend
  scsi: ufs: core: Do not put UFS power into LPM if link is broken
  scsi: qla2xxx: Prevent PRLI in target mode
  scsi: qla2xxx: Add marginal path handling support
  scsi: target: tcmu: Return from tcmu_handle_completions() if cmd_id not found
  scsi: ufs: core: Fix a typo in ufs-sysfs.c
  scsi: lpfc: Fix bad memory access during VPD DUMP mailbox command
  scsi: lpfc: Fix DMA virtual address ptr assignment in bsg
  scsi: lpfc: Fix illegal memory access on Abort IOCBs
  scsi: blk-mq: Fix build warning when making htmldocs

Pull more Kbuild updates from Masahiro Yamada:

 - Convert sh and sparc to use generic shell scripts to generate the
   syscall headers

 - refactor .gitignore files

 - Update kernel/config_data.gz only when the content of the .config
   is really changed, which avoids the unneeded re-link of vmlinux

 - move "remove stale files" workarounds to scripts/remove-stale-files

 - suppress unused-but-set-variable warnings by default for Clang
   as well

 - fix locale setting LANG=C to LC_ALL=C

 - improve 'make distclean'

 - always keep intermediate objects from scripts/link-vmlinux.sh

 - move IF_ENABLED out of <linux/kconfig.h> to make it self-contained

 - misc cleanups

* tag 'kbuild-v5.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (25 commits)
  linux/kconfig.h: replace IF_ENABLED() with PTR_IF() in <linux/kernel.h>
  kbuild: Don't remove link-vmlinux temporary files on exit/signal
  kbuild: remove the unneeded comments for external module builds
  kbuild: make distclean remove tag files in sub-directories
  kbuild: make distclean work against $(objtree) instead of $(srctree)
  kbuild: refactor modname-multi by using suffix-search
  kbuild: refactor fdtoverlay rule
  kbuild: parameterize the .o part of suffix-search
  arch: use cross_compiling to check whether it is a cross build or not
  kbuild: remove ARCH=sh64 support from top Makefile
  .gitignore: prefix local generated files with a slash
  kbuild: replace LANG=C with LC_ALL=C
  Makefile: Move -Wno-unused-but-set-variable out of GCC only block
  kbuild: add a script to remove stale generated files
  kbuild: update config_data.gz only when the content of .config is changed
  .gitignore: ignore only top-level modules.builtin
  .gitignore: move tags and TAGS close to other tag files
  kernel/.gitgnore: remove stale timeconst.h and hz.bc
  usr/include: refactor .gitignore
  genksyms: fix stale comment
  ...

Mounting with "multichannel" is obviously implied if user requested
more than one channel on mount (ie mount parm max_channels>1).
Currently both have to be specified. Fix that so that if max_channels
is greater than 1 on mount, enable multichannel rather than silently
falling back to non-multichannel.
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-By: Tom Talpey <tom@talpey.com>
Cc: <stable@vger.kernel.org> # v5.11+
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>

We were ignoring CAP_MULTI_CHANNEL in the server response - if the
server doesn't support multichannel we should not be attempting it.

See MS-SMB2 section 3.2.5.2
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Reviewed-By: Tom Talpey <tom@talpey.com>
Cc: <stable@vger.kernel.org> # v5.8+
Signed-off-by: Steve French <stfrench@microsoft.com>

Pull powerpc updates and fixes from Michael Ellerman:
 "A bit of a mixture of things, tying up some loose ends.

  There's the removal of the nvlink code, which dependend on a commit in
  the vfio tree. Then the enablement of huge vmalloc which was in next
  for a few weeks but got dropped due to conflicts. And there's also a
  few fixes.

  Summary:

   - Remove the nvlink support now that it's only user has been removed.

   - Enable huge vmalloc mappings for Radix MMU (P9).

   - Fix KVM conversion to gfn-based MMU notifier callbacks.

   - Fix a kexec/kdump crash with hot plugged CPUs.

   - Fix boot failure on 32-bit with CONFIG_STACKPROTECTOR.

   - Restore alphabetic order of the selects under CONFIG_PPC.

  Thanks to: Christophe Leroy, Christoph Hellwig, Nicholas Piggin,
  Sandipan Das, and Sourabh Jain"

* tag 'powerpc-5.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  KVM: PPC: Book3S HV: Fix conversion to gfn-based MMU notifier callbacks
  powerpc/kconfig: Restore alphabetic order of the selects under CONFIG_PPC
  powerpc/32: Fix boot failure with CONFIG_STACKPROTECTOR
  powerpc/powernv/memtrace: Fix dcache flushing
  powerpc/kexec_file: Use current CPU info while setting up FDT
  powerpc/64s/radix: Enable huge vmalloc mappings
  powerpc/powernv: remove the nvlink support