Update vga tuning algorithm to the one used in mt76x2 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add mt76x02_init_agc_gain routine in mt76x02-lib moudule in
order to be reused by mt76x0 for vga initalization
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move mt76x02_phy_adjust_vga_gain routine in mt76x02-lib module
in order to be reused by mt76x0 driver for vga calibration
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move mt76x2_get_rssi_gain_thresh and mt76x2_get_low_rssi_gain_thresh
routines in mt76x02-lib module in order to be reused by mt76x0 driver
for dynamic vga calibration
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce phy/vco temperature calibration.
Moreover fix configuration of register 67 on bank0
during temperature reading and use mt76_poll utility routine
to poll core34 register.
Furthermore temperature compensation needs to be disabled
if the device supports tssi compensation.
This issue has never been hit since temperature reading is not
actually used by usb code.

Fixes: 10de7a8b ("mt76x0: phy files")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add mt76x0_tssi_enabled in order to check if tssi compensation
is enabled since mt76x0 condition differs from mt76x2 one.
Moreover move back mt76x02_temp_tx_alc_enabled and mt76x02_tssi_enabled
routines in mt76x2/eeprom.h since they are mt76x2 specific
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Do not run mt76x0_vco_cal and mt76x0_bbp_set_bw routines and
configure MT_TX_SW_CFG0 register for pcie devices in
mt76x0_phy_set_channel function.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add mt76x0_phy_calirate routine in order to perform
phy calibration for mt76x0e devices.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Rename mt76x0_phy_calibrate routine in mt76x0_phy_calibration_work
in order to not collide with calibration routine for mt76x0e
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move mt76x02_phy_set_band routine in mt76x02_phy.c since
it is shared between mt76x0 and mt76x2 drivers and remove
duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move mt76x02_phy_set_bw routine in mt76x02_phy.c since
it is shared between mt76x0 and mt76x2 drivers and remove
duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Remove unused channel parameter from mt76x0_phy_set_chan_bbp_params
routine signature
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fix restore value configured in MT_BBP(IBI, 9) register in
mt76x0_phy_recalibrate_after_assoc routine.

Fixes: 10de7a8b ("mt76x0: phy files")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

- Use the register number define instead of a magic value
- Fix inverted bit test (override needs to be applied if the bit is not set)

Fixes: 2b2cb40b ("mt76x0: pci: add hw initialization at bootstrap")
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/wireless/mediatek/mt76/mt76x0/pci.c: In function 'mt76x0e_register_device':
drivers/net/wireless/mediatek/mt76/mt76x0/pci.c:107:8: warning:
 variable 'data' set but not used [-Wunused-but-set-variable]

It seems correct value to write is 'data'

Fixes: 2b2cb40b ("mt76x0: pci: add hw initialization at bootstrap")
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fixes a rare corner case where a BlockAckReq might get the wrong
sequence number.
Signed-off-by: Felix Fietkau <nbd@nbd.name>

dma.h is not used any longer.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Reserve enough room for USB skb, so we don not need to check
the room every time we send frame.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Run mt76x0_register_device routine in mt76x0e_register_device
in order to register the device to the mac80211 layer.
Moreover init mt76_driver_ops data structure and register
interrupt line
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Disable ldpc coding for mt76x0 devices. Morover remove
mt76x02_mac_fill_txwi routine since it is used just in
mt76x02_mac_write_txwi
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add missing mac80211 callbacks in mt76x0e_ops data structure
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Report via ethtool fw_ver and build_ver members of mt76x02_fw_header
data structure similarly to what is reported in the syslog
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use mt76x02_dev data structure as reference in mt76x02_eeprom.c
instead of mt76_dev
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use mt76x02_dev data structure as reference in mt76x02_txrx.c
instead of mt76_dev
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use mt76x02_dev data structure as reference in mt76x02_mac.c
instead of mt76_dev
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use mt76x02_dev data structure as reference in mt76x02_usb_mcu.c
instead of mt76_dev
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use mt76x02_dev data structure as reference in mt76x02_util.c
instead of mt76_dev
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use mt76x02_dev data structure as reference in mt76x02_phy.c
instead of mt76_dev
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use mt76x02_dev data structure as reference in mt76x02_mcu.c
instead of mt76_dev
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fix typo in bank check in mt76x0_rf_csr_{wr,rr} routines.
This issue has never been hit since mt76x0_rf_csr_{wr,rr}
are actually used just by pci code

Fixes: 10de7a8b ("mt76x0: phy files")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use mt76_is_usb() to identify RF access method instead of
MT76_STATE_MCU_RUNNING flag and add warning since MCU has
to be initialized before we can access RF registers via MCU.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

We have to use RF CSR method for PCIe.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add helpers to identify bus type.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

PCIe version don't use MCU for RF registers access. We need
to correct RF CSR method to support up to 127 RF registers.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use dev_dbg to print BBP version.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Function _rtl8821ae_mrate_idx_to_arfr_id is functionally identical to
the generic version rtl_mrate_idx_to_arfr_id, so remove
_rtl8821ae_mrate_idx_to_arfr_id and use the generic one instead.

This also fixes a missing break statement found by CoverityScan in
_rtl8821ae_mrate_idx_to_arfr_id, namely: CID#1167237 ("Missing break
in switch")

Thanks to Joe Perches for spotting this when I submitted an earlier patch.

Fixes: 3c05bedb ("Staging: rtl8812ae: Add Realtek 8821 PCI WIFI driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
ACKed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The rs_rate_from_ucode_rate() function may return -EINVAL if the rate
is invalid, but none of the callsites check for the error, potentially
making us access arrays with index IWL_RATE_INVALID, which is larger
than the arrays, causing an out-of-bounds access.  This will trigger
KASAN warnings, such as the one reported in the bugzilla issue
mentioned below.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=200659

Cc: stable@vger.kernel.org
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Merge tag 'iwlwifi-next-for-kalle-2018-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next

Fourth set of iwlwifi patches intended for 4.20

* Support for a new scan type;
* Clean-up in the queue handling code;
* A few bug fixes;

Conflicts were easy to resolve using immediate context mostly,
except the cls_u32.c one where I simply too the entire HEAD
chunk.
Signed-off-by: David S. Miller <davem@davemloft.net>

Julian Wiedmann says:

====================
s390/qeth: updates 2018-10-12

please apply one more patchset for net-next. This extends the TSO support
in qeth.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>