- 19 Sep, 2016 6 commits
-
-
Jason Baron authored
BugLink: http://bugs.launchpad.net/bugs/1619766 Skylake adjusts some register locations, but otherwise follows the existing model quite closely. I was able to verify that the 'ce_count' increments when 'bad dimms' are used. The accounting of 'ce_count' and 'ue_count' is the primary functionality of interest for us. Tested on Intel(R) Xeon(R) CPU E3-1260L v5 @ 2.90GHz. Signed-off-by:
Jason Baron <jbaron@akamai.com> Acked-by:
Tony Luck <tony.luck@intel.com> Cc: linux-edac <linux-edac@vger.kernel.org> Link: http://lkml.kernel.org/r/1462547927-22679-1-git-send-email-jbaron@akamai.comSigned-off-by:
Borislav Petkov <bp@suse.de> (cherry picked from commit 953dee9b) Signed-off-by:
Joseph Salisbury <joseph.salisbury@canonical.com> Acked-by:
Tim Gardner <tim.gardner@canonical.com> Signed-off-by:
Kamal Mostafa <kamal@canonical.com>
-
Gabriel Krisman Bertazi authored
Pending 4.8-rc merge. BugLink: http://bugs.launchpad.net/bugs/1602724 This fixes a regression in my previous commit c21377f8 ("nvme: Suspend all queues before deletion"), which provoked an Oops in the removal path when removing a device that became IO incapable very early at probe (i.e. after a failed EEH recovery). Turns out, if the error occurred very early at the probe path, before even configuring the admin queue, we might try to suspend the uninitialized admin queue, accessing bad memory. Fixes: c21377f8 ("nvme: Suspend all queues before deletion") Signed-off-by:
Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com> Reviewed-by:
Jay Freyensee <james_p_freyensee@linux.intel.com> Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
Brad Figg <brad.figg@canonical.com> Signed-off-by:
-
Jens Axboe authored
BugLink: http://bugs.launchpad.net/bugs/1620317 We do this in a few places, if the CPU is offline. This isn't allowed, though, since on multi queue hardware, we can't just move a request from one software queue to another, if they map to different hardware queues. The request and tag isn't valid on another hardware queue. This can happen if plugging races with CPU offlining. But it does no harm, since it can only happen in the window where we are currently busy freezing the queue and flushing IO, in preparation for redoing the software <-> hardware queue mappings. Signed-off-by:
-
Jens Axboe authored
BugLink: http://bugs.launchpad.net/bugs/1620317 __blk_mq_run_hw_queue() currently warns if we are running the queue on a CPU that isn't set in its mask. However, this can happen if a CPU is being offlined, and the workqueue handling will place the work on CPU0 instead. Improve the warning so that it only triggers if the batch cpu in the hardware queue is currently online. If it triggers for that case, then it's indicative of a flow problem in blk-mq, so we want to retain it for that case. Signed-off-by:
-
Gabriel Krisman Bertazi authored
BugLink: http://bugs.launchpad.net/bugs/1620317 In case a submitted request gets stuck for some reason, the block layer can prevent the request starvation by starting the scheduled timeout work. If this stuck request occurs at the same time another thread has started a queue freeze, the blk_mq_timeout_work will not be able to acquire the queue reference and will return silently, thus not issuing the timeout. But since the request is already holding a q_usage_counter reference and is unable to complete, it will never release its reference, preventing the queue from completing the freeze started by first thread. This puts the request_queue in a hung state, forever waiting for the freeze completion. This was observed while running IO to a NVMe device at the same time we toggled the CPU hotplug code. Eventually, once a request got stuck requiring a timeout during a queue freeze, we saw the CPU Hotplug notification code get stuck inside blk_mq_freeze_queue_wait, as shown in the trace below. [c000000deaf13690] [c000000deaf13738] 0xc000000deaf13738 (unreliable) [c000000deaf13860] [c000000000015ce8] __switch_to+0x1f8/0x350 [c000000deaf138b0] [c000000000ade0e4] __schedule+0x314/0x990 [c000000deaf13940] [c000000000ade7a8] schedule+0x48/0xc0 [c000000deaf13970] [c0000000005492a4] blk_mq_freeze_queue_wait+0x74/0x110 [c000000deaf139e0] [c00000000054b6a8] blk_mq_queue_reinit_notify+0x1a8/0x2e0 [c000000deaf13a40] [c0000000000e7878] notifier_call_chain+0x98/0x100 [c000000deaf13a90] [c0000000000b8e08] cpu_notify_nofail+0x48/0xa0 [c000000deaf13ac0] [c0000000000b92f0] _cpu_down+0x2a0/0x400 [c000000deaf13b90] [c0000000000b94a8] cpu_down+0x58/0xa0 [c000000deaf13bc0] [c0000000006d5dcc] cpu_subsys_offline+0x2c/0x50 [c000000deaf13bf0] [c0000000006cd244] device_offline+0x104/0x140 [c000000deaf13c30] [c0000000006cd40c] online_store+0x6c/0xc0 [c000000deaf13c80] [c0000000006c8c78] dev_attr_store+0x68/0xa0 [c000000deaf13cc0] [c0000000003974d0] sysfs_kf_write+0x80/0xb0 [c000000deaf13d00] [c0000000003963e8] kernfs_fop_write+0x188/0x200 [c000000deaf13d50] [c0000000002e0f6c] __vfs_write+0x6c/0xe0 [c000000deaf13d90] [c0000000002e1ca0] vfs_write+0xc0/0x230 [c000000deaf13de0] [c0000000002e2cdc] SyS_write+0x6c/0x110 [c000000deaf13e30] [c000000000009204] system_call+0x38/0xb4 The fix is to allow the timeout work to execute in the window between dropping the initial refcount reference and the release of the last reference, which actually marks the freeze completion. This can be achieved with percpu_refcount_tryget, which does not require the counter to be alive. This way the timeout work can do it's job and terminate a stuck request even during a freeze, returning its reference and avoiding the deadlock. Allowing the timeout to run is just a part of the fix, since for some devices, we might get stuck again inside the device driver's timeout handler, should it attempt to allocate a new request in that path - which is a quite common action for Abort commands, which need to be sent after a timeout. In NVMe, for instance, we call blk_mq_alloc_request from inside the timeout handler, which will fail during a freeze, since it also tries to acquire a queue reference. I considered a similar change to blk_mq_alloc_request as a generic solution for further device driver hangs, but we can't do that, since it would allow new requests to disturb the freeze process. I thought about creating a new function in the block layer to support unfreezable requests for these occasions, but after working on it for a while, I feel like this should be handled in a per-driver basis. I'm now experimenting with changes to the NVMe timeout path, but I'm open to suggestions of ways to make this generic. Signed-off-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Luke Dashjr authored
BugLink: http://bugs.launchpad.net/bugs/1619918 32-bit ioctl uses these rather than the regular FS_IOC_* versions. They can be handled in btrfs using the same code. Without this, 32-bit {ch,ls}attr fail. Signed-off-by:
Luke Dashjr <luke-jr+git@utopios.org> Cc: stable@vger.kernel.org Reviewed-by:
Josef Bacik <jbacik@fb.com> Reviewed-by:
David Sterba <dsterba@suse.com> Signed-off-by:
-
- 16 Sep, 2016 34 commits
-
-
Alex Deucher authored
BugLink: http://bugs.launchpad.net/bugs/1600092 When I fixed the dp rate selection in: 092c96a8 drm/radeon: fix dp link rate selection (v2) I accidently dropped the special handling for NUTMEG DP bridge chips. They require a fixed link rate. Reviewed-by:
Christian König <christian.koenig@amd.com> Reviewed-by:
Ken Wang <Qingqing.Wang@amd.com> Reviewed-by:
Harry Wentland <harry.wentland@amd.com> Tested-by:
Ken Moffat <zarniwhoop@ntlworld.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org (cherry picked from commit c8213a63) Signed-off-by:
-
Yuval Mintz authored
BugLink: http://bugs.launchpad.net/bugs/1623187 Module is using a binary firmware file and so should be marked as such. Signed-off-by:
Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by:
David S. Miller <davem@davemloft.net> (cherry picked from commit d43d3f0f) Signed-off-by:
dann frazier <dann.frazier@canonical.com> Acked-by:
-
Alexander Duyck authored
BugLink: http://bugs.launchpad.net/bugs/1616677 This change makes it so that we can just use function pointers instead of having to identify if a given VF is running on a Linux or Windows PF. By doing this we can avoid having to pull too much information out of the lower layers and can instead just make use of the mac_ops pointers since they should differ between the two types of VFs anyway. Signed-off-by:
Alexander Duyck <aduyck@mirantis.com> Tested-by:
Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> (cherry picked from commit 2f8214fe) Signed-off-by:
-
Babu Moger authored
BugLink: http://bugs.launchpad.net/bugs/1616677 We noticed performance issues with VF interface on sparc compared to PF. Setting the RX to IXGBE_DCA_RXCTRL_DATA_WRO_EN brings it on far with PF. Also this matches to the default sparc setting in PF driver. Signed-off-by:
Babu Moger <babu.moger@oracle.com> Acked-by:
Sowmini Varadhan <sowmini.varadhan@oracle.com> Tested-by:
-
KY Srinivasan authored
BugLink: http://bugs.launchpad.net/bugs/1616677 On Hyper-V, the VF/PF communication is a via software mediated path as opposed to the hardware mailbox. Make the necessary adjustments to support Hyper-V. Signed-off-by:
K. Y. Srinivasan <kys@microsoft.com> Tested-by:
-
KY Srinivasan authored
BugLink: http://bugs.launchpad.net/bugs/1616677 Intel SR-IOV cards present different ID when running on Hyper-V. Add the device IDs presented while running on Hyper-V. Signed-off-by:
-
Alexander Duyck authored
BugLink: http://bugs.launchpad.net/bugs/1616677 This patch moves API negotiation into mac_ops. The general idea here is that with HyperV on the way we need to make certain that anything that will have different versions between HyperV and a standard VF needs to be abstracted enough so that we can have a separate function between the two so we can avoid changes in one breaking something in the other. Signed-off-by:
-
Jacob Keller authored
BugLink: http://bugs.launchpad.net/bugs/1616677 Also cleanup a case where we're bit shifting a value into place, and use an unsigned constant. Make use of the unsigned postfix in places where BIT() macro is not appropriate. Signed-off-by:
Jacob Keller <jacob.e.keller@intel.com> Tested-by:
-
Emil Tantilov authored
BugLink: http://bugs.launchpad.net/bugs/1616677 Implement per-queue statistics for packets, bytes and busy poll specific counters. Signed-off-by:
Emil Tantilov <emil.s.tantilov@intel.com> Tested-by:
-
Emil Tantilov authored
BugLink: http://bugs.launchpad.net/bugs/1616677 This brings the logic closer to how we handle the stats in ixgbe and it sets us up for introducing per-queue stats. Use IXGBEVF_STAT and IXGBEVF_NETDEV_STAT for accessing the driver and netdev stats respectively. This way we don't have to calculate the stats based on register values which could lead to the counters not being initialized properly when the interface is down. IXGBEVF_QUEUE_STATS_LEN is set to include the number of queues. Also some defines were renamed to use the IXGBEVF prefix. Signed-off-by:
-
Alexander Duyck authored
BugLink: http://bugs.launchpad.net/bugs/1616677 This patch enables bulk free in Tx cleanup for ixgbevf and cleans up the boolean logic in the polling routines for ixgbe and ixgbevf in the hopes of avoiding any mix-ups similar to what occurred with i40e and i40evf. Signed-off-by:
-
Alexander Duyck authored
BugLink: http://bugs.launchpad.net/bugs/1616677 This patch adds support for generic Tx checksums to the ixgbevf driver. It turns out this is actually pretty easy after going over the datasheet as we were doing a number of steps we didn't need to. In order to perform a Tx checksum for an L4 header we need to fill in the following fields in the Tx descriptor: MACLEN (maximum of 127), retrieved from: skb_network_offset() IPLEN (maximum of 511), retrieved from: skb_checksum_start_offset() - skb_network_offset() TUCMD.L4T indicates offset and if checksum or crc32c, based on: skb->csum_offset The added advantage to doing this is that we can support inner checksum offloads for tunnels and MPLS while still being able to transparently insert VLAN tags. I also took the opportunity to clean-up many of the feature flag configuration bits to make them a bit more consistent between drivers. In the case of the VF drivers this meant adding support for SCTP CRCs, and inner checksum offloads for MPLS and various tunnel types. Signed-off-by:
-
Emil Tantilov authored
BugLink: http://bugs.launchpad.net/bugs/1616677 Move the reset flags to adapter->state in order to make use of bit operations. This is an alternative patch to the one previously submitted by John Greene. Suggested-by:
Scott Otto <otts62@yahoo.com> Reported-by:
John Greene <jogreene@redhat.com> Signed-off-by:
Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by:
-
Emil Tantilov authored
BugLink: http://bugs.launchpad.net/bugs/1616677 Return error when a MAC address change is rejected by the PF. This will prevent the user from modifying the MAC address when that operation is not permitted. Signed-off-by:
-
Stefan Assmann authored
BugLink: http://bugs.launchpad.net/bugs/1616677 Calling dev_close() causes IFF_UP to be cleared which will remove the interfaces routes and some addresses. That's probably not what the user intended when running the offline selftest. Besides this does not happen if the interface is brought down before the test, so the current behaviour is inconsistent. Instead call the net_device_ops ndo_stop function directly and avoid touching IFF_UP at all. Signed-off-by:
Stefan Assmann <sassmann@kpanic.de> Tested-by:
-
K. Y. Srinivasan authored
BugLink: http://bugs.launchpad.net/bugs/1616677 Use the virt_xx barriers that have been defined for use in virtual machines. Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> (back ported from commit dcd0eeca) Signed-off-by:
-
Vitaly Kuznetsov authored
BugLink: http://bugs.launchpad.net/bugs/1616677 Bonding driver sets IFF_BONDING on both master (the bonding device) and slave (the real NIC) devices and in netvsc_netdev_event() we want to skip master devices only. Currently, there is an uncertainty when a slave interface is removed: if bonding module comes first in netdev_chain it clears IFF_BONDING flag on the netdev and netvsc_netdev_event() correctly handles NETDEV_UNREGISTER event, but in case netvsc comes first on the chain it sees the device with IFF_BONDING still attached and skips it. As we still hold vf_netdev pointer to the device we crash on the next inject. Signed-off-by:
Vitaly Kuznetsov <vkuznets@redhat.com> Acked-by:
Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by:
-
Vitaly Kuznetsov authored
BugLink: http://bugs.launchpad.net/bugs/1616677 We're not guaranteed to see NETDEV_REGISTER/NETDEV_UNREGISTER notifications only once per VF but we increase/decrease module refcount unconditionally. Check vf_netdev to make sure we don't take/release it twice. We presume that only one VF per netvsc device may exist. Signed-off-by:
-
Vitaly Kuznetsov authored
BugLink: http://bugs.launchpad.net/bugs/1616677 We reset vf_inject on VF going down (netvsc_vf_down()) but we don't on VF removal (netvsc_unregister_vf()) so vf_inject stays 'true' while vf_netdev is already NULL and we're trying to inject packets into NULL net device in netvsc_recv_callback() causing kernel to crash. Signed-off-by:
-
Vitaly Kuznetsov authored
BugLink: http://bugs.launchpad.net/bugs/1616677 Here is a deadlock scenario: - netvsc_vf_up() schedules netvsc_notify_peers() work and quits. - netvsc_vf_down() runs before netvsc_notify_peers() gets executed. As it is being executed from netdev notifier chain we hold rtnl lock when we get here. - we enter while (atomic_read(&net_device_ctx->vf_use_cnt) != 0) loop and wait till netvsc_notify_peers() drops vf_use_cnt. - netvsc_notify_peers() starts on some other CPU but netdev_notify_peers() will hang on rtnl_lock(). - deadlock! Instead of introducing additional synchronization I suggest we drop gwrk.dwrk completely and call NETDEV_NOTIFY_PEERS directly. As we're acting under rtnl lock this is legitimate. Signed-off-by:
-
Vitaly Kuznetsov authored
BugLink: http://bugs.launchpad.net/bugs/1616677 struct netvsc_device is not suitable for storing VF information as this structure is being destroyed on MTU change / set channel operation (see rndis_filter_device_remove()). Move all VF related stuff to struct net_device_context which is persistent. Signed-off-by:
-
Haiyang Zhang authored
BugLink: http://bugs.launchpad.net/bugs/1616677 Added a condition to avoid bonding devices with same MAC registering as VF. Signed-off-by:
-
Cathy Avery authored
BugLink: http://bugs.launchpad.net/bugs/1616677 SR-IOV disabled from the host causes a memory leak. pci-hyperv usually first receives a PCI_EJECT notification and then proceeds to delete the hpdev list entry in hv_eject_device_work(). Later in hv_msi_free() since the device is no longer on the device list hpdev is NULL and hv_msi_free returns without freeing int_desc as part of hv_int_desc_free(). Signed-off-by:
Cathy Avery <cavery@redhat.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Acked-by:
Jake Oshins <jakeo@microsoft.com> (cherry picked from commit 0c6e617f) Signed-off-by:
-
Paul Gortmaker authored
BugLink: http://bugs.launchpad.net/bugs/1616677 Historically a lot of these existed because we did not have a distinction between what was modular code and what was providing support to modules via EXPORT_SYMBOL and friends. That changed when we forked out support for the latter into the export.h file. This means we should be able to reduce the usage of module.h in code that is obj-y Makefile or bool Kconfig. The advantage in doing so is that module.h itself sources about 15 other headers; adding significantly to what we feed cpp, and it can obscure what headers we are effectively using. Since module.h was the source for init.h (for __init) and for export.h (for EXPORT_SYMBOL) we consider each obj-y/bool instance for the presence of either and replace as needed. Build testing revealed some implicit header usage that was fixed up accordingly. Note that some bool/obj-y instances remain since module.h is the header for some exception table entry stuff, and for things like __init_or_module (code that is tossed when MODULES=n). Signed-off-by:
Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/20160714001901.31603-4-paul.gortmaker@windriver.comSigned-off-by:
Ingo Molnar <mingo@kernel.org> (cherry picked from commit 186f4360) Signed-off-by:
-
K. Y. Srinivasan authored
BugLink: http://bugs.launchpad.net/bugs/1616677 Use the new APIs for eliminating a copy on the receive path. These new APIs also help in minimizing the number of memory barriers we end up issuing (in the ringbuffer code) since we can better control when we want to expose the ring state to the host. The patch is being resent to address earlier email issues. Signed-off-by:
-
Vitaly Kuznetsov authored
BugLink: http://bugs.launchpad.net/bugs/1616677 When we have an interrupt from the host we have a bit set in event page indicating there are messages for the particular channel. We need to read them all as we won't get signaled for what was on the queue before we cleared the bit in vmbus_on_event(). This applies to all Hyper-V drivers and the pass-through driver should do the same. I did not meet any bugs; the issue was found by code inspection. We don't have many events going through hv_pci_onchannelcallback(), which explains why nobody reported the issue before. While on it, fix handling non-zero vmbus_recvpacket_raw() return values by dropping out. If the return value is not zero, it is wrong to inspect buffer or bytes_recvd as these may contain invalid data. Signed-off-by:
-
Vitaly Kuznetsov authored
BugLink: http://bugs.launchpad.net/bugs/1616677 We don't free buffer on several code paths in hv_pci_onchannelcallback(), put kfree() to the end of the function to fix the issue. Direct { kfree(); return; } can now be replaced with a simple 'break'; Signed-off-by:
-
Vitaly Kuznetsov authored
BugLink: http://bugs.launchpad.net/bugs/1616677 I'm hitting 5 second timeout in rndis_filter_set_rss_param() while setting RSS parameters for the device. When this happens we end up returning -ETIMEDOUT from the function and rndis_filter_device_add() falls back to setting net_device->max_chn = 1; net_device->num_chn = 1; net_device->num_sc_offered = 0; but after a moment the rndis request succeeds and subchannels start to appear. netvsc_sc_open() does unconditional nvscdev->num_sc_offered-- and it becomes U32_MAX-1. Consequent rndis_filter_device_remove() will hang while waiting for all U32_MAX-1 subchannels to appear and this is not going to happen. The immediate issue could be solved by adding num_sc_offered > 0 check to netvsc_sc_open() but we're getting out of sync with the host and it's not easy to adjust things later, e.g. in this particular case we'll be creating queues without a user request for it and races are expected. Same applies to other parts of the driver which have the same completion timeout. Following the trend in drivers/hv/* code I suggest we remove all these timeouts completely. As a guest we can always trust the host we're running on and if the host screws things up there is no easy way to recover anyway. Signed-off-by:
-
Vitaly Kuznetsov authored
BugLink: http://bugs.launchpad.net/bugs/1616677 The only caller rndis_filter_device_add() has 'struct net_device' pointer already. Signed-off-by:
-
Vitaly Kuznetsov authored
BugLink: http://bugs.launchpad.net/bugs/1616677 We unpack 'struct net_device' in netvsc_set_mac_addr() to get to 'struct hv_device' pointer which we use in rndis_filter_set_device_mac() to get back to 'struct net_device'. Signed-off-by:
-
Vitaly Kuznetsov authored
BugLink: http://bugs.launchpad.net/bugs/1616677 Both rndis_filter_open()/rndis_filter_close() use struct hv_device to reach to struct netvsc_device only and all callers have it already. While on it, rename net_device to nvdev in rndis_filter_open() as net_device is misleading. Signed-off-by:
-
Vitaly Kuznetsov authored
BugLink: http://bugs.launchpad.net/bugs/1616677 Make it easier to get 'struct netvsc_device' from 'struct net_device' and 'struct hv_device' by introducing inline helpers. Signed-off-by:
-
Vitaly Kuznetsov authored
BugLink: http://bugs.launchpad.net/bugs/1616677 net_device_ctx is assigned in the very beginning of the function and 'net' pointer doesn't change. Signed-off-by:
-
Haiyang Zhang authored
BugLink: http://bugs.launchpad.net/bugs/1616677 Added a condition to avoid vlan devices with same MAC registering as VF. Signed-off-by:
-
