Convert the Maxim Integrated MAX98095 audio codec bindings to DT schema.
Add missing sound-dai-cells during conversion.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230211134755.86061-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Commit 2458adb8
("SoC: simple-card-utils: set 0Hz to sysclk when shutdown")
added a call to snd_soc_dai_set_sysclk() with 0 Hz frequency. Being
propagated further it causes a division by zero in clk-ep93xx driver:

Division by zero in kernel.
CPU: 0 PID: 52 Comm: aplay Tainted: G        W          6.2.0-rc4-... #1
Hardware name: Generic DT based system
 unwind_backtrace from show_stack+0x10/0x18
 show_stack from dump_stack_lvl+0x28/0x34
 dump_stack_lvl from __div0+0x10/0x1c
 __div0 from Ldiv0+0x8/0x1c
 Ldiv0 from ep93xx_mux_determine_rate+0x78/0x1d0
 ep93xx_mux_determine_rate from clk_core_round_rate_nolock+0x48/0xc8
 clk_core_round_rate_nolock from clk_core_set_rate_nolock+0x48/0x160
 clk_core_set_rate_nolock from clk_set_rate+0x30/0x8c
 clk_set_rate from ep93xx_i2s_set_sysclk+0x30/0x6c
 ep93xx_i2s_set_sysclk from snd_soc_dai_set_sysclk+0x3c/0xa4
 snd_soc_dai_set_sysclk from asoc_simple_shutdown+0xb8/0x164
 asoc_simple_shutdown from snd_soc_link_shutdown+0x44/0x54
 snd_soc_link_shutdown from soc_pcm_clean+0x78/0x180
 soc_pcm_clean from soc_pcm_close+0x28/0x40
 soc_pcm_close from snd_pcm_release_substream.part.0+0x3c/0x84
 snd_pcm_release_substream.part.0 from snd_pcm_release+0x40/0x88
 snd_pcm_release from __fput+0x74/0x278

There has been commit f1879d7b ("ASoC: rockchip: ignore 0Hz sysclk"),
but it prepared by far not all drivers.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20230212220923.258414-1-alexander.sverdlin@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

This patch fixes
1. coding style issues
2. check if the setting was set already in rt712_sdca_mux_put callback
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20230210082141.24077-1-shumingf@realtek.comSigned-off-by: Mark Brown <broonie@kernel.org>

Current rsnd silently uses default TDM width if it was strange
settings. It is difficult to notice about it.
This patch indicates warning for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87lel6ksqn.wl-kuninori.morimoto.gx@renesas.comSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
From q6dsp side issues are around locking of position pointer and handle
From LPASS codec side most of the staiblity issues were around runtime pm,:

While testing X13s audio, we found multiple stablity issues this patchset
fixes these issues.
From q6dsp side issues are around locking of position pointer and handle
multiple prepare cases along with pulse audio timerbased scheduling workaround.

From LPASS codec side most of the staiblity issues were around runtime pm,
hitting various issues as the codec was firstly resetting the soundwire block
for every clk disable/enable which is taking the slaves out of sync and
resulting in re-enumerating. Second issue was around fsgen clk is not
brining up the codec out of suspend as it was not added after
runtime pm enabled. Final issue was with codec mclk rate which should
have been 192KHz same as npl instead of 96KHz. We were getting lucky as
wsa drivers are setting the same clk to 192KHz.

With this patches, x13s audio is pretty stable.

Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>:

In a course of creating complicated topologies where multiple output pins of a
copier is enabled, we have discovered that additional configuration needs to be
sent to the firmware to make the use cases working.

Merge series from Herve Codina <herve.codina@bootlin.com>:

The Infineon PEB2466 codec is a programmable DSP-based four channels
codec with filters capabilities.
It also provides signals as GPIOs.

It seems that SM8550 ADSP remote processor uses two IOMMUs.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230206150532.513468-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The WCD9340 audio codec appears on Slimbus twice: as IFD device without
properties and the actual audio-codec referencing the former via
wcd9340_ifd.  Allow in the binding both versions to fix several warnings
like:

  sdm850-samsung-w737.dtb: ifd@0,0: 'reset-gpios' is a required property
  sdm850-samsung-w737.dtb: ifd@0,0: 'slim-ifc-dev' is a required property
  sdm850-samsung-w737.dtb: ifd@0,0: 'interrupt-controller' is a required property
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230206180805.6621-3-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The "slim-ifc-dev" property should not be just "true", because it allows
any type.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230206180805.6621-2-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Reference common DAI properties to fix:

  sdm845-db845c.dtb: speaker@0,1: 'sound-name-prefix' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230206180805.6621-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

This is the initial codec driver for rt712 SDCA (Jack+Amp topology).
The host should connect with rt712 SdW1 interface.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20230207090946.20659-1-shumingf@realtek.comSigned-off-by: Mark Brown <broonie@kernel.org>

Simple-card/audio-graph-card drivers do not handle MCLK clock when it
is specified in the codec device node. The expectation here is that,
the codec should actually own up the MCLK clock and do necessary setup
in the driver.

This is inspired from,
commit dbf54a95 ("ASoC: rt5659: Update MCLK rate in set_sysclk()").

Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/1675953417-8686-2-git-send-email-spujar@nvidia.comSigned-off-by: Mark Brown <broonie@kernel.org>

After contributing the driver, add myself as the maintainer for the
Infineon PEB2466 codec.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Link: https://lore.kernel.org/r/20230206144904.91078-4-herve.codina@bootlin.comSigned-off-by: Mark Brown <broonie@kernel.org>

The Infineon PEB2466 codec is a programmable DSP-based four channels
codec with filters capabilities.
It also provides signals as GPIOs.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Link: https://lore.kernel.org/r/20230206144904.91078-3-herve.codina@bootlin.comSigned-off-by: Mark Brown <broonie@kernel.org>

The Infineon PEB2466 codec is a programmable DSP-based four channels
codec with filters capabilities.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230206144904.91078-2-herve.codina@bootlin.comSigned-off-by: Mark Brown <broonie@kernel.org>

MOD_INIT_INSTANCE IPC for a copier only contains the sink format for
output pin 0. Any additional output pins that are used need to have their
sink format set using the LARGE_CONFIG_SET IPC message.
Otherwise, firmware will report error or crash due to NULL format is used.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230209142123.17193-3-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Print the queue ID's during bind/unbind errors as well to make it easier
to see what failed exactly.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230209142123.17193-2-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230209122806.18923-9-srinivas.kandagatla@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

resetting soundwire block will put the slaves out of sync and result
in re-enumeration during fsgen disable/enable path this is totally
unnecessary and resulting fifo overflows.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230209122806.18923-8-srinivas.kandagatla@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

For some reason we ended up with incorrect mclk rate which should be
1920000 instead of 96000, So far we were getting lucky as the same clk
is set to 192000 by wsa and va macro. This issue is discovered when there
is no wsa macro active and only rx or tx path is tested.
Fix this by setting correct rate.

Fixes: c39667dd ("ASoC: codecs: lpass-tx-macro: add support for lpass tx macro")
Fixes: af3d54b9 ("ASoC: codecs: lpass-rx-macro: add support for lpass rx macro")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230209122806.18923-7-srinivas.kandagatla@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

move mclk out registration after runtime pm is enabled so that the
clk framework can resume the codec if it requires to enable the mclk out.

Fixes: c96baa29 ("ASoC: codecs: wsa-macro: add runtime pm support")
Fixes: 72ad25ea ("ASoC: codecs: va-macro: add runtime pm support")
Fixes: 366ff79e ("ASoC: codecs: rx-macro: add runtime pm support")
Fixes: 1fb83bc5 ("ASoC: codecs: tx-macro: add runtime pm support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230209122806.18923-6-srinivas.kandagatla@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

currently q6apm_is_adsp_ready() will only return the cached value of
previous result. If we are unlucky and previous result is not-ready
then the caller will always get not-ready flag.

This is not correct, we should query the dsp of its current state in
irrespective of previous reported state.

Fixes: 47bc8cf6 ("ASoC: qdsp6: audioreach: Add ADSP ready check")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230209122806.18923-5-srinivas.kandagatla@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

At the moment, playing audio with PulseAudio with the qdsp6 driver
results in distorted sound. It seems like its timer-based scheduling
does not work properly with qdsp6 since setting tsched=0 in
the PulseAudio configuration avoids the issue.

Apparently this happens when the pointer() callback is not accurate
enough. There is a SNDRV_PCM_INFO_BATCH flag that can be used to stop
PulseAudio from using timer-based scheduling by default.

According to https://www.alsa-project.org/pipermail/alsa-devel/2014-March/073816.html:

The flag is being used in the sense explained in the previous audio
meeting -- the data transfer granularity isn't fine enough but aligned
to the period size (or less).

q6apm-dai reports the position as multiple of

prtd->pcm_count = snd_pcm_lib_period_bytes(substream)

so it indeed just a multiple of the period size.

Therefore adding the flag here seems appropriate and makes audio
work out of the box.

Comment log inspired by Stephan Gerhold sent for q6asm-dai.c few years back.

Fixes: 9b4fe0f1 ("ASoC: qdsp6: audioreach: add q6apm-dai support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230209122806.18923-4-srinivas.kandagatla@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

It is noticed that the position pointer value seems to get a get corrupted
due to missing locking between updating and reading.

Fix this by adding a spinlock around the position pointer.

Fixes: 9b4fe0f1 ("ASoC: qdsp6: audioreach: add q6apm-dai support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230209122806.18923-3-srinivas.kandagatla@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

prepare callback can be called multiple times, so unprepare the stream
if its already prepared.

Without this DSP is not happy to setting the params on a already
prepared graph.

Fixes: 9b4fe0f1 ("ASoC: qdsp6: audioreach: add q6apm-dai support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230209122806.18923-2-srinivas.kandagatla@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

In SMA1303, this device does not support MCLK.
So it need to remove sysclk setting in devicetree.
Signed-off-by: Kiseok Jo <kiseok.jo@irondevice.com>
Link: https://lore.kernel.org/r/20230209084903.13000-2-kiseok.jo@irondevice.comSigned-off-by: Mark Brown <broonie@kernel.org>

The max98090 has only one DAI, so snd_soc_dai_driver does not have to be
an array.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230208160410.371609-2-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Convert the Maxim Integrated MAX98090/MAX98091 audio codecs bindings to
DT schema.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230208160410.371609-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Convert the DT binding documentation for the Amlogic axg sound card to
schema.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230208093520.52843-2-jbrunet@baylibre.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add the missing properties as compatible, reg, sound-dai-cells.
And then check this file using 'make dt_binding_check'.
Signed-off-by: Kiseok Jo <kiseok.jo@irondevice.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230208092420.5037-8-kiseok.jo@irondevice.comSigned-off-by: Mark Brown <broonie@kernel.org>

It seems correct that the user changes the TDM slot needed after
device probe.
Signed-off-by: Kiseok Jo <kiseok.jo@irondevice.com>
Link: https://lore.kernel.org/r/20230208092420.5037-6-kiseok.jo@irondevice.comSigned-off-by: Mark Brown <broonie@kernel.org>

It's necessary to set the value for each device, so remove that.
Signed-off-by: Kiseok Jo <kiseok.jo@irondevice.com>
Link: https://lore.kernel.org/r/20230208092420.5037-5-kiseok.jo@irondevice.comSigned-off-by: Mark Brown <broonie@kernel.org>

Tidyup reg/reg-name "maxItems".
Pointed by Krzysztof, and corrected by Rob.

Link: https://lore.kernel.org/r/46974ae7-5f7f-8fc1-4ea8-fe77b58f5bfb@linaro.org
Link: https://lore.kernel.org/r/20230207211621.GA4158591-robh@kernel.orgReported-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/87pmalt01x.wl-kuninori.morimoto.gx@renesas.comSigned-off-by: Mark Brown <broonie@kernel.org>

Convert the DT binding documentation for the Amlogic axg spdif output to
schema.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230206153449.596326-7-jbrunet@baylibre.comSigned-off-by: Mark Brown <broonie@kernel.org>

Convert the DT binding documentation for the Amlogic axg spdif input to
schema.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230206153449.596326-6-jbrunet@baylibre.comSigned-off-by: Mark Brown <broonie@kernel.org>

Convert the DT binding documentation for the Amlogic axg audio FIFOs to
schema.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230206153449.596326-5-jbrunet@baylibre.comSigned-off-by: Mark Brown <broonie@kernel.org>

Convert the DT binding documentation for the Amlogic axg PDM device to
schema.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230206153449.596326-4-jbrunet@baylibre.comSigned-off-by: Mark Brown <broonie@kernel.org>

Convert the DT binding documentation for the Amlogic tdm formatters to
schema.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230206153449.596326-3-jbrunet@baylibre.comSigned-off-by: Mark Brown <broonie@kernel.org>

Convert the DT binding documentation for the Amlogic tdm interface to
schema.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230206153449.596326-2-jbrunet@baylibre.comSigned-off-by: Mark Brown <broonie@kernel.org>