- 05 Nov, 2014 9 commits
-
-
Giuseppe CAVALLARO authored
This patch aims to fix the concurrency in eee initialization inside the stmmac driver and related warnings when enable DEBUG_ATOMIC_SLEEP. Prior this patch, the stmmac_eee_init could be called in several places as shown below: stmmac_open stmmac_resume PHY Layer | | | stmmac_hw_setup stmmac_adjust_link | | stmmac ethtool |__________________________|______________| | stmmac_eee_init The patch removes the stmmac_eee_init call inside the stmmac_hw_setup that is unnecessary. It is sufficient to call it in the adjust_link to always guarantee that EEE is always configured at mac level too. Fixing the lock protection now it is covered another case (not considered before). The stmmac_eee_init could be called by the ethtool so critical sections must be protected inside this function too. Signed-off-by:Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Giuseppe CAVALLARO authored
When compile with CONFIG_PROVE_LOCKING the following warnings happen: [snip] HARDIRQ-ON-W at: [<c0480c1c>] _raw_spin_lock+0x3c/0x4c [<c02c2828>] stmmac_set_rx_mode+0x18/0x3c [<c038b2cc>] dev_set_rx_mode+0x1c/0x28 [<c038b38c>] __dev_open+0xb4/0xf8 [<c038b5a8>] __dev_change_flags+0x94/0x128 [<c038b6a8>] dev_change_flags+0x10/0x48 [<c062afe0>] ip_auto_config+0x1d4/0x1084 [<c000873c>] do_one_initcall+0x108/0x15c [<c060ec50>] kernel_init_freeable+0x1a8/0x248 [<c0472cc0>] kernel_init+0x8/0x160 [<c000dfc8>] ret_from_fork+0x14/0x2c INITIAL USE at: [<c0480c1c>] _raw_spin_lock+0x3c/0x4c [<c02c2828>] stmmac_set_rx_mode+0x18/0x3c [<c038b2cc>] dev_set_rx_mode+0x1c/0x28 [<c038b38c>] __dev_open+0xb4/0xf8 [<c038b5a8>] __dev_change_flags+0x94/0x128 [<c038b6a8>] dev_change_flags+0x10/0x48 [<c062afe0>] ip_auto_config+0x1d4/0x1084 [<c000873c>] do_one_initcall+0x108/0x15c [<c060ec50>] kernel_init_freeable+0x1a8/0x248 [<c0472cc0>] kernel_init+0x8/0x160 [<c000dfc8>] ret_from_fork+0x14/0x2c so the patch just removes the lock protection in the stmmac_set_rx_mode Signed-off-by: -
Fabrice Gasnier authored
Add missing spin_unlock when tx frames gets dropped. Signed-off-by:
Fabrice Gasnier <fabrice.gasnier@st.com> Acked-by:
-
Fabrice Gasnier authored
stmmac_tx_avail() may lie if used unprotected. It's using cur_tx and dirty_tx index. These index may be already in use by tx_clean when entering xmit routine. So, this should be called locked. This can cause transmit queue to be stuck, with following message: NETDEV WATCHDOG: eth0 (stmmaceth): transmit queue 0 timed out Signed-off-by:
-
Chen Gang authored
drivers: net: ethernet: xilinx: xilinx_emaclite: revert the original commit "1db3ddff" Microblaze is a fpga soft core, it can be customized easily, which may cause many various hardware version strings. So the original fix patch based on hard-coded compatible version strings is not a good idea (although it is correct for current issue). For it, there will be a new solving way soon (which based on the device tree). The original issue is related with qemu, so can only change the hardware version string in qemu for it, then keep the original driver no touch ( qemu is for virtualization which has much easier life than real world). Signed-off-by:
Chen Gang <gang.chen.5i5j@gmail.com> Acked-by:
Michal Simek <michal.simek@xilinx.com> Signed-off-by:
-
Rasmus Villemoes authored
File descriptors are always closed on exit :-) Signed-off-by:
Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by:
-
Loganaden Velvindron authored
It was initially sent by Lorenzo Colitti, but was subsequently lost in the final diff he submitted. Signed-off-by:
Loganaden Velvindron <logan@elandsys.com> Signed-off-by:
-
Jesse Gross authored
The pernet ops aren't ever unregistered, which causes a memory leak and an OOPs if the module is ever reinserted. Fixes: 0b5e8b8e ("net: Add Geneve tunneling protocol driver") CC: Andy Zhou <azhou@nicira.com> Signed-off-by:
Jesse Gross <jesse@nicira.com> Acked-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by:
-
Jesse Gross authored
Geneve does not currently set the inner protocol type when transmitting packets. This causes GSO segmentation to fail on NICs that do not support Geneve offloading. CC: Andy Zhou <azhou@nicira.com> Signed-off-by:
-
- 04 Nov, 2014 4 commits
-
-
David S. Miller authored
Iyappan Subramanian says: ==================== drivers: net: xgene: Fix crash for backward compatibility This patch set fixes the following issues that were reported during regression. Patch 1,2 : Adds backward compatibility with the older firmware (<= 1.13.28). Patch 3 : Use separate hardware resources (descriptor ring, prefetch buffer) that are not shared with the firmware ==================== Signed-off-by: -
Iyappan Subramanian authored
This patch fixes the following kernel crash during SGMII based 1GbE probe. BUG: Bad page state in process swapper/0 pfn:40fe6ad page:ffffffbee37a75d8 count:-1 mapcount:0 mapping: (null) index:0x0 flags: 0x0() page dumped because: nonzero _count Modules linked in: CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.17.0+ #7 Call trace: [<ffffffc000087fa0>] dump_backtrace+0x0/0x12c [<ffffffc0000880dc>] show_stack+0x10/0x1c [<ffffffc0004d981c>] dump_stack+0x74/0xc4 [<ffffffc00012fe70>] bad_page+0xd8/0x128 [<ffffffc000133000>] get_page_from_freelist+0x4b8/0x640 [<ffffffc000133260>] __alloc_pages_nodemask+0xd8/0x834 [<ffffffc0004194f8>] __netdev_alloc_frag+0x124/0x1b8 [<ffffffc00041bfdc>] __netdev_alloc_skb+0x90/0x10c [<ffffffc00039ff30>] xgene_enet_refill_bufpool+0x11c/0x280 [<ffffffc0003a11a4>] xgene_enet_process_ring+0x168/0x340 [<ffffffc0003a1498>] xgene_enet_napi+0x1c/0x50 [<ffffffc00042b454>] net_rx_action+0xc8/0x18c [<ffffffc0000b0880>] __do_softirq+0x114/0x24c [<ffffffc0000b0c34>] irq_exit+0x94/0xc8 [<ffffffc0000e68a0>] __handle_domain_irq+0x8c/0xf4 [<ffffffc000081288>] gic_handle_irq+0x30/0x7c This was due to hardware resource sharing conflict with the firmware. This patch fixes this crash by using resources (descriptor ring, prefetch buffer) that are not shared. Signed-off-by:
Iyappan Subramanian <isubramanian@apm.com> Signed-off-by:
Keyur Chudgar <kchudgar@apm.com> Signed-off-by:
-
Iyappan Subramanian authored
This patch adds support when used with older firmware (<= 1.13.28). - Added xgene_ring_mgr_init() to check whether ring manager is initialized - Calling xgene_ring_mgr_init() from xgene_port_ops.reset() - To handle errors, changed the return type of xgene_port_ops.reset() Signed-off-by:
-
Iyappan Subramanian authored
The following kernel crash was reported when using older firmware (<= 1.13.28). [ 0.980000] libphy: APM X-Gene MDIO bus: probed [ 1.130000] Unhandled fault: synchronous external abort (0x96000010) at 0xffffff800009a17c [ 1.140000] Internal error: : 96000010 [#1] SMP [ 1.140000] Modules linked in: [ 1.140000] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.17.0+ #21 [ 1.140000] task: ffffffc3f0110000 ti: ffffffc3f0064000 task.ti: ffffffc3f0064000 [ 1.140000] PC is at ioread32+0x58/0x68 [ 1.140000] LR is at xgene_enet_setup_ring+0x18c/0x1cc [ 1.140000] pc : [<ffffffc0003cec68>] lr : [<ffffffc00053dad8>] pstate: a0000045 [ 1.140000] sp : ffffffc3f0067b20 [ 1.140000] x29: ffffffc3f0067b20 x28: ffffffc000aa8ea0 [ 1.140000] x27: ffffffc000bb2000 x26: ffffffc000a64270 [ 1.140000] x25: ffffffc000b05ad8 x24: ffffffc0ff99ba58 [ 1.140000] x23: 0000000000004000 x22: 0000000000004000 [ 1.140000] x21: 0000000000000200 x20: 0000000000200000 [ 1.140000] x19: ffffffc0ff99ba18 x18: ffffffc0007a6000 [ 1.140000] x17: 0000000000000007 x16: 000000000000000e [ 1.140000] x15: 0000000000000001 x14: 0000000000000000 [ 1.140000] x13: ffffffbeedb71320 x12: 00000000ffffff80 [ 1.140000] x11: 0000000000000002 x10: 0000000000000000 [ 1.140000] x9 : 0000000000000000 x8 : ffffffc3eb2a4000 [ 1.140000] x7 : 0000000000000000 x6 : 0000000000000000 [ 1.140000] x5 : 0000000001080000 x4 : 000000007d654010 [ 1.140000] x3 : ffffffffffffffff x2 : 000000000003ffff [ 1.140000] x1 : ffffff800009a17c x0 : ffffff800009a17c The issue was that the older firmware does not support 10GbE and SGMII based 1GBE interfaces. This patch changes the address length of the reg property of sgmii0 and xgmii nodes and serves as preparatory patch for the fix. Signed-off-by:
Dann Frazier <dann.frazier@canonical.com> Signed-off-by:
-
- 03 Nov, 2014 13 commits
-
-
Edward Cree authored
efx_ef10_probe() was BUGging out if the BAR2 size was 0. This is unnecessarily violent; instead we should just fail to probe the device. Kept a WARN_ON as this problem indicates a broken or misconfigured NIC. Signed-off-by:
Edward Cree <ecree@solarflare.com> Signed-off-by:
-
David S. Miller authored
Steffen Klassert says: ==================== ipv6: Fix iflink setting for ipv6 tunnels The ipv6 tunnels do the dev->iflink setting too early, it gets overwritten by register_netdev(). So set dev->iflink from within a ndo_init function to keep the configured setting. This patchset fixes this for ip6_tunnel, vti6, sit and gre6. ==================== Signed-off-by: -
Steffen Klassert authored
Otherwise it gets overwritten by register_netdev(). Signed-off-by:
Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by:
-
Steffen Klassert authored
ipip6_tunnel_init() sets the dev->iflink via a call to ipip6_tunnel_bind_dev(). After that, register_netdevice() sets dev->iflink = -1. So we loose the iflink configuration for ipv6 tunnels. Fix this by using ipip6_tunnel_init() as the ndo_init function. Then ipip6_tunnel_init() is called after dev->iflink is set to -1 from register_netdevice(). Signed-off-by:
-
Steffen Klassert authored
vti6_dev_init() sets the dev->iflink via a call to vti6_link_config(). After that, register_netdevice() sets dev->iflink = -1. So we loose the iflink configuration for vti6 tunnels. Fix this by using vti6_dev_init() as the ndo_init function. Then vti6_dev_init() is called after dev->iflink is set to -1 from register_netdevice(). Signed-off-by:
-
Steffen Klassert authored
ip6_tnl_dev_init() sets the dev->iflink via a call to ip6_tnl_link_config(). After that, register_netdevice() sets dev->iflink = -1. So we loose the iflink configuration for ipv6 tunnels. Fix this by using ip6_tnl_dev_init() as the ndo_init function. Then ip6_tnl_dev_init() is called after dev->iflink is set to -1 from register_netdevice(). Signed-off-by:
-
Herbert Xu authored
When VLAN is in use in macvtap_put_user, we end up setting csum_start to the wrong place. The result is that the whoever ends up doing the checksum setting will corrupt the packet instead of writing the checksum to the expected location, usually this means writing the checksum with an offset of -4. This patch fixes this by adjusting csum_start when VLAN tags are detected. Fixes: f09e2249 ("macvtap: restore vlan header on user read") Cc: stable@vger.kernel.org Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Cheers, Signed-off-by:
-
Nimrod Andy authored
On i.MX6SX sdb platform, there has two same enet MACs, after system up, just eth0 is up, and then do suspend/resume test: [ 50.437967] PM: Syncing filesystems ... done. [ 50.476924] Freezing user space processes ... (elapsed 0.005 seconds) done. [ 50.490093] Freezing remaining freezable tasks ... (elapsed 0.004 seconds) done. [ 50.559771] ------------[ cut here ]------------ [ 50.564453] WARNING: CPU: 0 PID: 575 at drivers/clk/clk.c:851 __clk_disable+0x60/0x6c() [ 50.572475] Modules linked in: [ 50.575578] CPU: 0 PID: 575 Comm: sh Not tainted 3.18.0-rc2-next-20141031-00007-gf61135b #21 [ 50.584031] Backtrace: [ 50.586550] [<80011ecc>] (dump_backtrace) from [<8001206c>] (show_stack+0x18/0x1c) [ 50.594136] r6:808a7a54 r5:00000000 r4:00000000 r3:00000000 [ 50.599920] [<80012054>] (show_stack) from [<806ab3c0>] (dump_stack+0x80/0x9c) [ 50.607187] [<806ab340>] (dump_stack) from [<8002a3e8>] (warn_slowpath_common+0x6c/0x8c) [ 50.615294] r5:00000353 r4:00000000 [ 50.618940] [<8002a37c>] (warn_slowpath_common) from [<8002a42c>] (warn_slowpath_null+0x24/0x2c) [ 50.627738] r8:00000000 r7:be144c44 r6:be015600 r5:80070013 r4:be015600 [ 50.634573] [<8002a408>] (warn_slowpath_null) from [<804f8d4c>] (__clk_disable+0x60/0x6c) [ 50.642777] [<804f8cec>] (__clk_disable) from [<804f8e5c>] (clk_disable+0x2c/0x38) [ 50.650359] r4:be015600 r3:00000000 [ 50.654006] [<804f8e30>] (clk_disable) from [<80420ab4>] (fec_enet_clk_enable+0xc4/0x258) [ 50.662196] r5:be3cb620 r4:be3cb000 [ 50.665838] [<804209f0>] (fec_enet_clk_enable) from [<80421178>] (fec_suspend+0x30/0x180) [ 50.674026] r7:be144c44 r6:be144c10 r5:8037f5a4 r4:be3cb000 [ 50.679802] [<80421148>] (fec_suspend) from [<8037f5d8>] (platform_pm_suspend+0x34/0x64) [ 50.687906] r10:00000000 r9:00000000 r8:00000000 r7:be144c44 r6:be144c10 r5:8037f5a4 [ 50.695852] r4:be144c10 r3:80421148 [ 50.699511] [<8037f5a4>] (platform_pm_suspend) from [<8038784c>] (dpm_run_callback.isra.14+0x34/0x6c) [ 50.708764] [<80387818>] (dpm_run_callback.isra.14) from [<80387f00>] (__device_suspend+0x12c/0x2a4) [ 50.717909] r9:8098ec8c r8:80973bec r6:00000002 r5:811c7038 r4:be144c10 [ 50.724746] [<80387dd4>] (__device_suspend) from [<803894fc>] (dpm_suspend+0x64/0x224) [ 50.732675] r8:80973bec r7:be144c10 r6:8098ec24 r5:811c7038 r4:be144cc4 [ 50.739509] [<80389498>] (dpm_suspend) from [<8038999c>] (dpm_suspend_start+0x60/0x68) [ 50.747438] r10:8082fa24 r9:00000000 r8:00000004 r7:00000003 r6:00000000 r5:8116ec80 [ 50.755386] r4:00000002 [ 50.757969] [<8038993c>] (dpm_suspend_start) from [<800679d8>] (suspend_devices_and_enter+0x90/0x3ec) [ 50.767202] r4:00000003 r3:8116eca0 [ 50.770843] [<80067948>] (suspend_devices_and_enter) from [<80067f40>] (pm_suspend+0x20c/0x2a4) [ 50.779553] r8:00000004 r7:00000003 r6:00000000 r5:8116ec8c r4:00000003 [ 50.786394] [<80067d34>] (pm_suspend) from [<80066858>] (state_store+0x70/0xc0) [ 50.793718] r6:8116ec90 r5:00000003 r4:bd88a800 r3:0000006d [ 50.799496] [<800667e8>] (state_store) from [<802b0384>] (kobj_attr_store+0x1c/0x28) [ 50.807251] r10:bd399f78 r8:00000000 r7:bd88a800 r6:bd88a800 r5:00000004 r4:bd085680 [ 50.815219] [<802b0368>] (kobj_attr_store) from [<80153090>] (sysfs_kf_write+0x54/0x58) [ 50.823252] [<8015303c>] (sysfs_kf_write) from [<80151fd8>] (kernfs_fop_write+0xd0/0x194) [ 50.831441] r6:00000004 r5:bd08568c r4:bd085680 r3:8015303c [ 50.837220] [<80151f08>] (kernfs_fop_write) from [<800eddb4>] (vfs_write+0xb8/0x1a8) [ 50.844975] r10:00000000 r9:00000000 r8:00000000 r7:bd399f78 r6:01336408 r5:00000004 [ 50.852924] r4:bc584dc0 [ 50.855505] [<800edcfc>] (vfs_write) from [<800ee0b8>] (SyS_write+0x48/0x88) [ 50.862567] r10:00000000 r8:00000000 r7:01336408 r6:00000004 r5:bc584dc0 r4:bc584dc0 [ 50.870537] [<800ee070>] (SyS_write) from [<8000eb00>] (ret_fast_syscall+0x0/0x48) [ 50.878120] r9:bd398000 r8:8000ecc4 r7:00000004 r6:76f42b48 r5:01336408 r4:00000004 [ 50.885983] ---[ end trace 7545115d752a316a ]--- [ 50.890765] ------------[ cut here ]------------ The root cause is that eth1 is not opened and clock is not enabled, and .suspend() still call .fec_enet_clk_enable() to disable clock. To avoid the broken, let it check network device up status by calling .netif_running() before disable/enable clocks. Signed-off-by:
Fugang Duan <B38611@freescale.com> Signed-off-by:
-
David S. Miller authored
Herbert Xu says: ==================== tun: Fix csum_start and TUN_PKT_STRIP The first patch fixes a serious problem that breaks checksum offload in VMs while the second patch fixes a problem that probably affects no one. ==================== Signed-off-by: -
Herbert Xu authored
We set the flag TUN_PKT_STRIP if the user buffer provided is too small to contain the entire packet plus meta-data. However, this has been broken ever since we added GSO meta-data. VLAN acceleration also has the same problem. This patch fixes this by taking both into account when setting the TUN_PKT_STRIP flag. The fact that this has been broken for six years without anyone realising means that nobody actually uses this flag. Fixes: f43798c2 ("tun: Allow GSO using virtio_net_hdr") Signed-off-by:
-
Herbert Xu authored
When VLAN acceleration is in use on the xmit path, we end up setting csum_start to the wrong place. The result is that the whoever ends up doing the checksum setting will corrupt the packet instead of writing the checksum to the expected location, usually this means writing the checksum with an offset of -4. This patch fixes this by adjusting csum_start when VLAN acceleration is detected. Fixes: 6680ec68 ("tuntap: hardware vlan tx support") Cc: stable@vger.kernel.org Signed-off-by:
-
stephen hemminger authored
The makefile for sanitizing kernel headers uses the kbuild file to determine which files to do. Several networking related headers were missing. Without these headers iproute2 build would break. Signed-off-by:
Stephen Hemminger <stephen@networkplumber.org> Signed-off-by:
-
Guenter Roeck authored
Fix: net/bridge/netfilter/nft_reject_bridge.c: In function 'nft_reject_br_send_v6_unreach': net/bridge/netfilter/nft_reject_bridge.c:240:3: error: implicit declaration of function 'csum_ipv6_magic' csum_ipv6_magic(&nip6h->saddr, &nip6h->daddr, ^ make[3]: *** [net/bridge/netfilter/nft_reject_bridge.o] Error 1 Seen with powerpc:allmodconfig. Fixes: 523b929d ("netfilter: nft_reject_bridge: don't use IP stack to reject traffic") Cc: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
- 01 Nov, 2014 11 commits
-
-
Linus Walleij authored
The SMC91x is written to explicitly look up the IRQ resource from the platform device and extract the IRQ and flags, however the platform_get_irq() does additional things, like call of_irq_get() in the device tree case, which will translate the IRQ using the irqdomain and defer the probe if the IRQ host cannot be found. As we're not looking up the resource, this will not retrieve the IRQ flags, but that is better done using irqd_get_trigger_type(), as the trigger is what the driver wants to modify. We take care to preserve the semantics that will make the trigger type provided from the resource override any local specifier. Tested on the Nomadik NHK15 which has its SMC91x IRQ line connected to a STMPE2401 GPIO expander on I2C. Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Chen Gang authored
drivers: net: ethernet: xilinx: xilinx_emaclite: Compatible with 'xlnx, xps-ethernetlite-2.00.b' for QEMU using When use current latest upstream qemu (current version: 2.1.2), need let driver compatible with 'xlnx,xps-ethernetlite-2.00.b', or can not find net device in microblaze qemu. Related QEMU commands under fedora 20: yum install libvirt yum install tunctl tunctl -b ip link set tap0 up brctl addif virbr0 tap0 ./microblaze-softmmu/qemu-system-microblaze -M petalogix-s3adsp1800 \ -kernel ../linux-stable.microblaze/arch/microblaze/boot/linux.bin \ -no-reboot -append "console=ttyUL0,115200 doreboot" -nographic \ -net nic,vlan=0,model=xlnx.xps-ethernetlite,macaddr=00:16:35:AF:94:00 \ -net tap,vlan=0,ifname=tap0,script=no,downscript=no in microblaze qemu bash (guest machine): ifconfig eth0 add 192.168.122.2 netmask 255.255.255.0 ifconfig eth0 up After add this patch, can find the device, and can be used by 'telnetd' (need cross-build busybox with glibc for it), then outside can telnet to it without password. Signed-off-by: -
David S. Miller authored
Florian Fainelli says: ==================== net: systemport: TX dma fixes This patch series contains two fixes for our transmit path, first one is a pretty nasty one since we were not allocating a large enough dma coherent pool for our transmit descriptors, which would work most of the time, since allocations are contiguous and we could have. Second patch fixes a less frequent, though highly likley crash when using CMA allocations. ==================== Signed-off-by: -
Florian Fainelli authored
Callers of bcm_sysport_init_tx_ring() can currently fail, and will always call bcm_sysport_fini_tx_ring() in a loop ending at the number of TX queues (32) without checking if the TX ring was successfully initialized or not. Update bcm_sysport_fini_tx_ring() to return early and avoid a crash de-referencing ring->cbs if the TX ring was not initialized, since ring->cbs is the last part of the initialization done by bcm_sysport_init_tx_ring() that could fail. Fixes: 80105bef ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver") Reported-by:
Maxime Bizon <mbizon@freebox.fr> Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Florian Fainelli authored
We should not be allocating a single byte of DMA coherent memory, but instead a full-sized struct dma_desc (8 bytes). Fixes: 80105bef ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver") Signed-off-by:
-
Sudip Mukherjee authored
we are allocating memory using kzalloc for struct mvpp2_prs_entry, but later when we are getting error we were just returning the error value without releasing the memory. Signed-off-by:
Sudip Mukherjee <sudip@vectorindia.org> Signed-off-by:
-
David S. Miller authored
Reported-by:
Meelis Roos <mroos@linux.ee> Tested-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/inputLinus Torvalds authored
Pull input updates from Dmitry Torokhov: "A bunch of fixes for minor defects reported by Coverity, a few driver fixups and revert of i8042.nomux change so that we are once again enable active MUX mode if box claims to support it" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Revert "Input: i8042 - disable active multiplexing by default" Input: altera_ps2 - use correct type for irq return value Input: altera_ps2 - write to correct register when disabling interrupts Input: max77693-haptic - fix potential overflow Input: psmouse - remove unneeded check in psmouse_reconnect() Input: vsxxxaa - fix code dropping bytes from queue Input: ims-pcu - fix dead code in ims_pcu_ofn_reg_addr_store() Input: opencores-kbd - fix error handling Input: wm97xx - adapt parameters to tosa touchscreen. Input: i8042 - quirks for Fujitsu Lifebook A544 and Lifebook AH544 Input: stmpe-keypad - fix valid key line bitmask Input: soc_button_array - update calls to gpiod_get*()
-
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pmLinus Torvalds authored
Pull ACPI and power management fixes from Rafael Wysocki: "These are fixes received after my previous pull request plus one that has been in the works for quite a while, but its previous version caused problems to happen, so it's been deferred till now. Fixed are two recent regressions (MFD enumeration and cpufreq-dt), ACPI EC regression introduced in 3.17, system suspend error code path regression introduced in 3.15, an older bug related to recovery from failing resume from hibernation and a cpufreq-dt driver issue related to operation performance points. Specifics: - Fix a crash on r8a7791/koelsch during resume from system suspend caused by a recent cpufreq-dt commit (Geert Uytterhoeven). - Fix an MFD enumeration problem introduced by a recent commit adding ACPI support to the MFD subsystem that exposed a weakness in the ACPI core causing ACPI enumeration to be applied to all devices associated with one ACPI companion object, although it should be used for one of them only (Mika Westerberg). - Fix an ACPI EC regression introduced during the 3.17 cycle causing some Samsung laptops to misbehave as a result of a workaround targeted at some Acer machines. That includes a revert of a commit that went too far and a quirk for the Acer machines in question. From Lv Zheng. - Fix a regression in the system suspend error code path introduced during the 3.15 cycle that causes it to fail to take errors from asychronous execution of "late" suspend callbacks into account (Imre Deak). - Fix a long-standing bug in the hibernation resume error code path that fails to roll back everything correcty on "freeze" callback errors and leaves some devices in a "suspended" state causing more breakage to happen subsequently (Imre Deak). - Make the cpufreq-dt driver disable operation performance points that are not supported by the VR connected to the CPU voltage plane with acceptable tolerance instead of constantly failing voltage scaling later on (Lucas Stach)" * tag 'pm+acpi-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: ACPI / EC: Fix regression due to conflicting firmware behavior between Samsung and Acer. Revert "ACPI / EC: Add support to disallow QR_EC to be issued before completing previous QR_EC" cpufreq: cpufreq-dt: Restore default cpumask_setall(policy->cpus) PM / Sleep: fix recovery during resuming from hibernation PM / Sleep: fix async suspend_late/freeze_late error handling ACPI: Use ACPI companion to match only the first physical device cpufreq: cpufreq-dt: disable unsupported OPPs -
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pciLinus Torvalds authored
Pull PCI fixes from Bjorn Helgaas: "These changes, intended for v3.18, fix: Sysfs - Fix "enable" filename change (Greg Kroah-Hartman) An unintentional sysfs filename change in commit 5136b2da ("PCI: convert bus code to use dev_groups"), which appeared in v3.13, changed "enable" to "enabled", and this changes it back. Old users of "enable" are currently broken and will be helped by this change. Anything that started to use "enabled" after v3.13 will be broken by this change. If necessary, we can add a symlink to make both work, but this patch doesn't do that. PCI device hotplug - Revert duplicate merge (Kamal Mostafa) A mistaken duplicate merge that added a check twice. Nothing's broken; this just removes the unnecessary code. Freescale i.MX6 - Wait for clocks to stabilize after ref_en (Richard Zhu) An i.MX6 clock problem that prevents mx6 nitrogen boards from booting" * tag 'pci-v3.18-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: PCI: Rename sysfs 'enabled' file back to 'enable' PCI: imx6: Wait for clocks to stabilize after ref_en Revert duplicate "PCI: pciehp: Prevent NULL dereference during probe" -
Andy Lutomirski authored
Rusty noticed a Really Bad Bug (tm) in my NT fix. The entry code reads out of bounds, causing the NT fix to be unreliable. But, and this is much, much worse, if your stack is somehow just below the top of the direct map (or a hole), you read out of bounds and crash. Excerpt from the crash: [ 1.129513] RSP: 0018:ffff88001da4bf88 EFLAGS: 00010296 2b:* f7 84 24 90 00 00 00 testl $0x4000,0x90(%rsp) That read is deterministically above the top of the stack. I thought I even single-stepped through this code when I wrote it to check the offset, but I clearly screwed it up. Fixes: 8c7aa698 ("x86_64, entry: Filter RFLAGS.NT on entry from userspace") Reported-by:
Rusty Russell <rusty@ozlabs.org> Cc: stable@vger.kernel.org Signed-off-by:
Andy Lutomirski <luto@amacapital.net> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
- 31 Oct, 2014 3 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4Linus Torvalds authored
Pull ext4 bugfixes from Ted Ts'o: "A set of miscellaneous ext4 bug fixes for 3.18" * tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: ext4: make ext4_ext_convert_to_initialized() return proper number of blocks ext4: bail early when clearing inode journal flag fails ext4: bail out from make_indexed_dir() on first error jbd2: use a better hash function for the revoke table ext4: prevent bugon on race between write/fcntl ext4: remove extent status procfs files if journal load fails ext4: disallow changing journal_csum option during remount ext4: enable journal checksum when metadata checksum feature enabled ext4: fix oops when loading block bitmap failed ext4: fix overflow when updating superblock backups after resize
-
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fsLinus Torvalds authored
Pull quota and ext3 fixes from Jan Kara. * 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs: fs, jbd: use a more generic hash function quota: Properly return errors from dquot_writeback_dquots() ext3: Don't check quota format when there are no quota files
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds authored
Pull networking fixes from David Miller: "A bit has accumulated, but it's been a week or so since my last batch of post-merge-window fixes, so... 1) Missing module license in netfilter reject module, from Pablo. Lots of people ran into this. 2) Off by one in mac80211 baserate calculation, from Karl Beldan. 3) Fix incorrect return value from ax88179_178a driver's set_mac_addr op, which broke use of it with bonding. From Ian Morgan. 4) Checking of skb_gso_segment()'s return value was not all encompassing, it can return an SKB pointer, a pointer error, or NULL. Fix from Florian Westphal. This is crummy, and longer term will be fixed to just return error pointers or a real SKB. 6) Encapsulation offloads not being handled by skb_gso_transport_seglen(). From Florian Westphal. 7) Fix deadlock in TIPC stack, from Ying Xue. 8) Fix performance regression from using rhashtable for netlink sockets. The problem was the synchronize_net() invoked for every socket destroy. From Thomas Graf. 9) Fix bug in eBPF verifier, and remove the strong dependency of BPF on NET. From Alexei Starovoitov. 10) In qdisc_create(), use the correct interface to allocate ->cpu_bstats, otherwise the u64_stats_sync member isn't initialized properly. From Sabrina Dubroca. 11) Off by one in ip_set_nfnl_get_byindex(), from Dan Carpenter. 12) nf_tables_newchain() was erroneously expecting error pointers from netdev_alloc_pcpu_stats(). It only returna a valid pointer or NULL. From Sabrina Dubroca. 13) Fix use-after-free in _decode_session6(), from Li RongQing. 14) When we set the TX flow hash on a socket, we mistakenly do so before we've nailed down the final source port. Move the setting deeper to fix this. From Sathya Perla. 15) NAPI budget accounting in amd-xgbe driver was counting descriptors instead of full packets, fix from Thomas Lendacky. 16) Fix total_data_buflen calculation in hyperv driver, from Haiyang Zhang. 17) Fix bcma driver build with OF_ADDRESS disabled, from Hauke Mehrtens. 18) Fix mis-use of per-cpu memory in TCP md5 code. The problem is that something that ends up being vmalloc memory can't be passed to the crypto hash routines via scatter-gather lists. From Eric Dumazet. 19) Fix regression in promiscuous mode enabling in cdc-ether, from Olivier Blin. 20) Bucket eviction and frag entry killing can race with eachother, causing an unlink of the object from the wrong list. Fix from Nikolay Aleksandrov. 21) Missing initialization of spinlock in cxgb4 driver, from Anish Bhatt. 22) Do not cache ipv4 routing failures, otherwise if the sysctl for forwarding is subsequently enabled this won't be seen. From Nicolas Cavallari" * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (131 commits) drivers: net: cpsw: Support ALLMULTI and fix IFF_PROMISC in switch mode drivers: net: cpsw: Fix broken loop condition in switch mode net: ethtool: Return -EOPNOTSUPP if user space tries to read EEPROM with lengh 0 stmmac: pci: set default of the filter bins net: smc91x: Fix gpios for device tree based booting mpls: Allow mpls_gso to be built as module mpls: Fix mpls_gso handler. r8152: stop submitting intr for -EPROTO netfilter: nft_reject_bridge: restrict reject to prerouting and input netfilter: nft_reject_bridge: don't use IP stack to reject traffic netfilter: nf_reject_ipv6: split nf_send_reset6() in smaller functions netfilter: nf_reject_ipv4: split nf_send_reset() in smaller functions netfilter: nf_tables_bridge: update hook_mask to allow {pre,post}routing drivers/net: macvtap and tun depend on INET drivers/net, ipv6: Select IPv6 fragment idents for virtio UFO packets drivers/net: Disable UFO through virtio net: skb_fclone_busy() needs to detect orphaned skb gre: Use inner mac length when computing tunnel length mlx4: Avoid leaking steering rules on flow creation error flow net/mlx4_en: Don't attempt to TX offload the outer UDP checksum for VXLAN ...
-
