- 24 Mar, 2018 16 commits
-
-
Edgar Cherkasov authored
[ Upstream commit e058e7a4 ] Description of the problem: - i2c-scmi driver contains only two identifiers "SMBUS01" and "SMBUSIBM"; - the fist HID (SMBUS01) is clearly defined in "SMBus Control Method Interface Specification, version 1.0": "Each device must specify 'SMBUS01' as its _HID and use a unique _UID value"; - unfortunately, BIOS vendors (like AMI) seem to ignore this requirement and implement "SMB0001" HID instead of "SMBUS01"; - I speculate that they do this because only "SMB0001" is hard coded in Windows SMBus driver produced by Microsoft. This leads to following situation: - SMBus works out of box in Windows but not in Linux; - board vendors are forced to add correct "SMBUS01" HID to BIOS to make SMBus work in Linux. Moreover the same board vendors complain that tools (3-rd party ASL compiler) do not like the "SMBUS01" identifier and produce errors. So they need to constantly patch the compiler for each new version of BIOS. As it is very unlikely that BIOS vendors implement a correct HID in future, I would propose to consider whether it is possible to work around the problem by adding MS HID to the Linux i2c-scmi driver. v2: move the definition of the new HID to the driver itself. Signed-off-by:
Edgar Cherkasov <echerkasov@dev.rtsoft.ru> Signed-off-by:
Michael Brunner <Michael.Brunner@kontron.com> Acked-by:
Viktor Krasnov <vkrasnov@dev.rtsoft.ru> Reviewed-by:
Jean Delvare <jdelvare@suse.de> Reviewed-by:
Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
Sasha Levin <alexander.levin@microsoft.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Hans de Goede authored
[ Upstream commit 382bd4de ] When requesting a shared irq with IRQF_TRIGGER_NONE then the irqaction flags get filled with the trigger type from the irq_data: if (!(new->flags & IRQF_TRIGGER_MASK)) new->flags |= irqd_get_trigger_type(&desc->irq_data); On the first setup_irq() the trigger type in irq_data is NONE when the above code executes, then the irq is started up for the first time and then the actual trigger type gets established, but that's too late to fix up new->flags. When then a second user of the irq requests the irq with IRQF_TRIGGER_NONE its irqaction's triggertype gets set to the actual trigger type and the following check fails: if (!((old->flags ^ new->flags) & IRQF_TRIGGER_MASK)) Resulting in the request_irq failing with -EBUSY even though both users requested the irq with IRQF_SHARED | IRQF_TRIGGER_NONE Fix this by comparing the new irqaction's trigger type to the trigger type stored in the irq_data which correctly reflects the actual trigger type being used for the irq. Suggested-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Acked-by:
Marc Zyngier <marc.zyngier@arm.com> Link: http://lkml.kernel.org/r/20170415100831.17073-1-hdegoede@redhat.comSigned-off-by:
-
Thomas Gleixner authored
[ Upstream commit 205dcc1e ] The target() callback must run on the affected cpu. This is achieved by temporarily setting the affinity of the calling thread to the requested CPU and reset it to the original affinity afterwards. That's racy vs. concurrent affinity settings for that thread resulting in code executing on the wrong CPU. Replace it by work_on_cpu(). All call pathes which invoke the callbacks are already protected against CPU hotplug. Signed-off-by:
Viresh Kumar <viresh.kumar@linaro.org> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: Tony Luck <tony.luck@intel.com> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Sebastian Siewior <bigeasy@linutronix.de> Cc: linux-pm@vger.kernel.org Cc: Lai Jiangshan <jiangshanlai@gmail.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Tejun Heo <tj@kernel.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Len Brown <lenb@kernel.org> Link: http://lkml.kernel.org/r/20170412201042.958216363@linutronix.deSigned-off-by:
-
Thomas Gleixner authored
[ Upstream commit 8153f9ac ] acpi_processor_get_throttling() requires to invoke the getter function on the target CPU. This is achieved by temporarily setting the affinity of the calling user space thread to the requested CPU and reset it to the original affinity afterwards. That's racy vs. CPU hotplug and concurrent affinity settings for that thread resulting in code executing on the wrong CPU and overwriting the new affinity setting. acpi_processor_get_throttling() is invoked in two ways: 1) The CPU online callback, which is already running on the target CPU and obviously protected against hotplug and not affected by affinity settings. 2) The ACPI driver probe function, which is not protected against hotplug during modprobe. Switch it over to work_on_cpu() and protect the probe function against CPU hotplug. Signed-off-by:
-
Thomas Gleixner authored
[ Upstream commit a5cbdf69 ] When acpi_install_notify_handler() fails the cooling device stays registered and the sysfs files created via acpi_pss_perf_init() are leaked and the function returns success. Undo acpi_pss_perf_init() and return a proper error code. Signed-off-by:
-
Deepa Dinamani authored
[ Upstream commit d340266e ] struct timespec is not y2038 safe on 32 bit machines. The posix clocks apis use struct timespec directly and through struct itimerspec. Replace the posix clock interfaces to use struct timespec64 and struct itimerspec64 instead. Also fix up their implementations accordingly. Note that the clock_getres() interface has also been changed to use timespec64 even though this particular interface is not affected by the y2038 problem. This helps verification for internal kernel code for y2038 readiness by getting rid of time_t/ timeval/ timespec. Signed-off-by:
Deepa Dinamani <deepa.kernel@gmail.com> Cc: arnd@arndb.de Cc: y2038@lists.linaro.org Cc: netdev@vger.kernel.org Cc: Richard Cochran <richardcochran@gmail.com> Cc: john.stultz@linaro.org Link: http://lkml.kernel.org/r/1490555058-4603-3-git-send-email-deepa.kernel@gmail.comSigned-off-by:
-
Dmitry Torokhov authored
[ Upstream commit 95123fc4 ] The name field in structure i2c_device_id is 20 characters, and we expect it to be NULL-terminated, however we are trying to stuff it with 21 bytes and thus NULL-terminator is lost. This causes issues when one creates device with name "MICROCHIP_AR1021_I2C" as i2c core cuts off the last "C", and automatic module loading by alias does not work as result. The -I2C suffix in the device name is superfluous, we know what bus we are dealing with, so let's drop it. Also, no other driver uses capitals, and the manufacturer name is normally not included, except in very rare cases of incompatible name collisions. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=116211 Fixes: dd4cae8b ("Input: Add Microchip AR1021 i2c touchscreen") Reviewed-By:
Christian Gmeiner <christian.gmeiner@gmail.com> Tested-by:
Martin Kepplinger <martin.kepplinger@ginzinger.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Hans de Goede authored
[ Upstream commit a1e23a42 ] On some systems (e.g. Intel Bay Trail systems) the legacy PIC is not used, in this case virq 8 will be a random irq, rather then hw_irq 8 from the PIC. Requesting virq 8 in this case will not help us to get alarm irqs and may cause problems for other drivers which actually do need virq 8, for example on an Asus Transformer T100TA this leads to: [ 28.745155] genirq: Flags mismatch irq 8. 00000088 (mmc0) vs. 00000080 (rtc0) <snip oops> [ 28.753700] mmc0: Failed to request IRQ 8: -16 [ 28.975934] sdhci-acpi: probe of 80860F14:01 failed with error -16 This commit fixes this by making the rtc-cmos driver continue without using an irq rather then claiming irq 8 when no irq is specified in the pnp-info and there are no legacy-irqs. Signed-off-by:
Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by:
-
Hans de Goede authored
[ Upstream commit 7ee06cb2 ] The classic PC rtc-coms driver has a workaround for broken ACPI device nodes for it which lack an irq resource. This workaround used to unconditionally hardcode the irq to 8 in these cases. This was causing irq conflict problems on systems without a legacy-pic so a recent patch added an if (nr_legacy_irqs()) guard to the workaround to avoid this irq conflict. nr_legacy_irqs() uses the legacy_pic symbol under the hood causing an undefined symbol error if the rtc-cmos code is build as a module. This commit exports the legacy_pic symbol to fix this. Cc: rtc-linux@googlegroups.com Cc: alexandre.belloni@free-electrons.com Signed-off-by:
-
Dong Aisheng authored
[ Upstream commit 9bf94454 ] Set the initial voltage selector for vddpcie in case it's disabled by default. This fixes the below warning: 20c8000.anatop:regulator-vddpcie: Failed to read a valid default voltage selector. anatop_regulator: probe of 20c8000.anatop:regulator-vddpcie failed with error -22 Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <kernel@pengutronix.de> Cc: Robin Gong <yibin.gong@nxp.com> Cc: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by:
Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by:
Dong Aisheng <aisheng.dong@nxp.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Santeri Toivonen authored
[ Upstream commit f3582361 ] Asus laptop X302UA starts up with Wi-Fi disabled, without a way to enable it. Set wapf=4 to fix the problem. Signed-off-by:
Santeri Toivonen <santeri.toivonen@vatsul.com> Signed-off-by:
Darren Hart (VMware) <dvhart@infradead.org> Signed-off-by:
-
Yisheng Xie authored
commit 740a5759 upstream. ashmem_mutex may create a chain of dependencies like: CPU0 CPU1 mmap syscall ioctl syscall -> mmap_sem (acquired) -> ashmem_ioctl -> ashmem_mmap -> ashmem_mutex (acquired) -> ashmem_mutex (try to acquire) -> copy_from_user -> mmap_sem (try to acquire) There is a lock odering problem between mmap_sem and ashmem_mutex causing a lockdep splat[1] during a syzcaller test. This patch fixes the problem by move copy_from_user out of ashmem_mutex. [1] https://www.spinics.net/lists/kernel/msg2733200.html Fixes: ce8a3a9e (staging: android: ashmem: Fix a race condition in pin ioctls) Reported-by: syzbot+d7a918a7a8e1c952bc36@syzkaller.appspotmail.com Signed-off-by:
Yisheng Xie <xieyisheng1@huawei.com> Cc: "Joel Fernandes (Google)" <joel.opensrc@gmail.com> Signed-off-by:
-
Pavel Shilovsky authored
commit cabfb368 upstream. In order to allow encryption on SMB connection we need to exchange a session key and generate encryption and decryption keys. Signed-off-by:
Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by:
Srivatsa S. Bhat <srivatsa@csail.mit.edu> Cc: Steve French <smfrench@gmail.com> Signed-off-by:
-
Steve French authored
commit 4587eee0 upstream. According to MS-SMB2 3.2.55 validate_negotiate request must always be signed. Some Windows can fail the request if you send it unsigned See kernel bugzilla bug 197311 CC: Stable <stable@vger.kernel.org> Acked-by: Ronnie Sahlberg <lsahlber.redhat.com> Signed-off-by:
Steve French <smfrench@gmail.com> Signed-off-by:
-
Jeremy Boone authored
commit 6bb320ca upstream. Discrete TPMs are often connected over slow serial buses which, on some platforms, can have glitches causing bit flips. In all the driver _recv() functions, we need to use a u32 to unmarshal the response size, otherwise a bit flip of the 31st bit would cause the expected variable to go negative, which would then try to read a huge amount of data. Also sanity check that the expected amount of data is large enough for the TPM header. Signed-off-by:
Jeremy Boone <jeremy.boone@nccgroup.trust> Cc: stable@vger.kernel.org Signed-off-by:
James Bottomley <James.Bottomley@HansenPartnership.com> Tested-by:
Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Reviewed-by:
James Morris <james.morris@microsoft.com> Signed-off-by:
-
Jeremy Boone authored
commit 3be23274 upstream. Discrete TPMs are often connected over slow serial buses which, on some platforms, can have glitches causing bit flips. If a bit does flip it could cause an overrun if it's in one of the size parameters, so sanity check that we're not overrunning the provided buffer when doing a memcpy(). Signed-off-by:
-
- 22 Mar, 2018 24 commits
-
-
Greg Kroah-Hartman authored
-
Jann Horn authored
commit 95a762e2 upstream. Distinguish between BPF_ALU64|BPF_MOV|BPF_K (load 32-bit immediate, sign-extended to 64-bit) and BPF_ALU|BPF_MOV|BPF_K (load 32-bit immediate, zero-padded to 64-bit); only perform sign extension in the first case. This patch differs from the mainline one because the verifier's internals have changed in the meantime. Mainline tracks register values as 64-bit values; however, 4.4 still stores tracked register values as 32-bit values with sign extension. Therefore, in the case of a 32-bit op with negative immediate, the value can't be tracked; leave the register as UNKNOWN_VALUE (set by the preceding check_reg_arg() call). I have manually tested this patch on top of 4.4.122. For the following BPF bytecode: BPF_MOV64_IMM(BPF_REG_1, 1), BPF_JMP_IMM(BPF_JEQ, BPF_REG_1, 1, 1), BPF_EXIT_INSN(), BPF_MOV32_IMM(BPF_REG_1, 1), BPF_JMP_IMM(BPF_JEQ, BPF_REG_1, 1, 1), BPF_EXIT_INSN(), BPF_MOV64_IMM(BPF_REG_1, -1), BPF_JMP_IMM(BPF_JEQ, BPF_REG_1, -1, 1), BPF_EXIT_INSN(), BPF_MOV32_IMM(BPF_REG_1, -1), BPF_JMP_IMM(BPF_JEQ, BPF_REG_1, -1, 2), BPF_MOV32_IMM(BPF_REG_0, 42), BPF_EXIT_INSN(), BPF_MOV32_IMM(BPF_REG_0, 43), BPF_EXIT_INSN() Verifier output on 4.4.122 without this patch: 0: (b7) r1 = 1 1: (15) if r1 == 0x1 goto pc+1 3: (b4) (u32) r1 = (u32) 1 4: (15) if r1 == 0x1 goto pc+1 6: (b7) r1 = -1 7: (15) if r1 == 0xffffffff goto pc+1 9: (b4) (u32) r1 = (u32) -1 10: (15) if r1 == 0xffffffff goto pc+2 13: (b4) (u32) r0 = (u32) 43 14: (95) exit Verifier output on 4.4.122+ with this patch: 0: (b7) r1 = 1 1: (15) if r1 == 0x1 goto pc+1 3: (b4) (u32) r1 = (u32) 1 4: (15) if r1 == 0x1 goto pc+1 6: (b7) r1 = -1 7: (15) if r1 == 0xffffffff goto pc+1 9: (b4) (u32) r1 = (u32) -1 10: (15) if r1 == 0xffffffff goto pc+2 R1=inv R10=fp 11: (b4) (u32) r0 = (u32) 42 12: (95) exit from 10 to 13: R1=imm-1 R10=fp 13: (b4) (u32) r0 = (u32) 43 14: (95) exit Signed-off-by:
Jann Horn <jannh@google.com> Acked-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
-
Srinath Mannam authored
commit c8e4e5bd upstream. Corrected the register to check the 64-bit pointer capability state. 64-bit pointer implementation capability was checking in wrong register, which causes the BDC enumeration failure in 64-bit memory address. Fixes: efed421a ("usb: gadget: Add UDC driver for Broadcom USB3.0 device controller IP BDC") Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
Srinath Mannam <srinath.mannam@broadcom.com> Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
Wei Yongjun authored
commit 8874ae5f upstream. Add the missing platform_device_put() before return from bdc_pci_probe() in the platform_device_add_resources() error handling case. Fixes: efed421a ("usb: gadget: Add UDC driver for Broadcom USB3.0 device controller IP BDC") Signed-off-by:
Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by:
-
Nikolay Borisov authored
commit fd649f10 upstream. Commit 4fde46f0 ("Btrfs: free the stale device") introduced btrfs_free_stale_device which iterates the device lists for all registered btrfs filesystems and deletes those devices which aren't mounted. In a btrfs_devices structure has only 1 device attached to it and it is unused then btrfs_free_stale_devices will proceed to also free the btrfs_fs_devices struct itself. Currently this leads to a use after free since list_for_each_entry will try to perform a check on the already freed memory to see if it has to terminate the loop. The fix is to use 'break' when we know we are freeing the current fs_devs. Fixes: 4fde46f0 ("Btrfs: free the stale device") Signed-off-by:
Nikolay Borisov <nborisov@suse.com> Reviewed-by:
Anand Jain <anand.jain@oracle.com> Signed-off-by:
David Sterba <dsterba@suse.com> Signed-off-by:
-
Hans van Kranenburg authored
commit 92e222df upstream. In case of using DUP, we search for enough unallocated disk space on a device to hold two stripes. The devices_info[ndevs-1].max_avail that holds the amount of unallocated space found is directly assigned to stripe_size, while it's actually twice the stripe size. Later on in the code, an unconditional division of stripe_size by dev_stripes corrects the value, but in the meantime there's a check to see if the stripe_size does not exceed max_chunk_size. Since during this check stripe_size is twice the amount as intended, the check will reduce the stripe_size to max_chunk_size if the actual correct to be used stripe_size is more than half the amount of max_chunk_size. The unconditional division later tries to correct stripe_size, but will actually make sure we can't allocate more than half the max_chunk_size. Fix this by moving the division by dev_stripes before the max chunk size check, so it always contains the right value, instead of putting a duct tape division in further on to get it fixed again. Since in all other cases than DUP, dev_stripes is 1, this change only affects DUP. Other attempts in the past were made to fix this: * 37db63a4 "Btrfs: fix max chunk size check in chunk allocator" tried to fix the same problem, but still resulted in part of the code acting on a wrongly doubled stripe_size value. * 86db2578 "Btrfs: fix max chunk size on raid5/6" unintentionally broke this fix again. The real problem was already introduced with the rest of the code in 73c5de00. The user visible result however will be that the max chunk size for DUP will suddenly double, while it's actually acting according to the limits in the code again like it was 5 years ago. Reported-by:
Naohiro Aota <naohiro.aota@wdc.com> Link: https://www.spinics.net/lists/linux-btrfs/msg69752.html Fixes: 73c5de00 ("btrfs: quasi-round-robin for chunk allocation") Fixes: 86db2578 ("Btrfs: fix max chunk size on raid5/6") Signed-off-by:
Hans van Kranenburg <hans.van.kranenburg@mendix.com> Reviewed-by:
-
Adam Ford authored
commit 74402055 upstream. The pinmuxing was missing for I2C1 which was causing intermittent issues with the PMIC which is connected to I2C1. The bootloader did not quite configure the I2C1 either, so when running at 2.6MHz, it was generating errors at time. This correctly sets the I2C1 pinmuxing so it can operate at 2.6MHz Fixes: 687c2767 ("ARM: dts: Add minimal support for LogicPD Torpedo DM3730 devkit") Signed-off-by:
Adam Ford <aford173@gmail.com> Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Johannes Thumshirn authored
commit f930c704 upstream. Don't make any assumptions on the sg_io_hdr_t::dxfer_direction or the sg_io_hdr_t::dxferp in order to determine if it is a valid request. The only way we can check for bad requests is by checking if the length exceeds 256M. Signed-off-by:
Johannes Thumshirn <jthumshirn@suse.de> Fixes: 28676d86 (scsi: sg: check for valid direction before starting the request) Reported-by:
Jason L Tibbitts III <tibbs@math.uh.edu> Tested-by:
Doug Gilbert <dgilbert@interlog.com> Cc: Doug Gilbert <dgilbert@interlog.com> Cc: <stable@vger.kernel.org> Reviewed-by:
Hannes Reinecke <hare@suse.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Johannes Thumshirn authored
commit 14074aba upstream. dxfer_len is an unsigned int and we always assign a value > 0 to it, so it doesn't make any sense to check if it is < 0. We can't really check dxferp as well as we have both NULL and not NULL cases in the possible call paths. So just return true for SG_DXFER_FROM_DEV transfer in sg_is_valid_dxfer(). Signed-off-by:
Colin Ian King <colin.king@canonical.com> Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Cc: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by:
-
Johannes Thumshirn authored
commit 68c59fce upstream. SG_DXFER_FROM_DEV transfers do not necessarily have a dxferp as we set it to NULL for the old sg_io read/write interface, but must have a length bigger than 0. This fixes a regression introduced by commit 28676d86 ("scsi: sg: check for valid direction before starting the request") Signed-off-by:
Chris Clayton <chris2553@googlemail.com> Tested-by:
-
Ard Biesheuvel authored
commit 4f2c7583 upstream. When struct its_device instances are created, the nr_ites member will be set to a power of 2 that equals or exceeds the requested number of MSIs passed to the msi_prepare() callback. At the same time, the LPI map is allocated to be some multiple of 32 in size, where the allocated size may be less than the requested size depending on whether a contiguous range of sufficient size is available in the global LPI bitmap. This may result in the situation where the nr_ites < nr_lpis, and since nr_ites is what we program into the hardware when we map the device, the additional LPIs will be non-functional. For bog standard hardware, this does not really matter. However, in cases where ITS device IDs are shared between different PCIe devices, we may end up allocating these additional LPIs without taking into account that they don't actually work. So let's make nr_ites at least 32. This ensures that all allocated LPIs are 'live', and that its_alloc_device_irq() will fail when attempts are made to allocate MSIs beyond what was allocated in the first place. Signed-off-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> [maz: updated comment] Signed-off-by:
-
Tejun Heo authored
commit d0264c01 upstream. While converting ioctx index from a list to a table, db446a08 ("aio: convert the ioctx list to table lookup v3") missed tagging kioctx_table->table[] as an array of RCU pointers and using the appropriate RCU accessors. This introduces a small window in the lookup path where init and access may race. Mark kioctx_table->table[] with __rcu and use the approriate RCU accessors when using the field. Signed-off-by:
Tejun Heo <tj@kernel.org> Reported-by:
-
Tejun Heo authored
commit a6d7cff4 upstream. While fixing refcounting, e34ecee2 ("aio: Fix a trinity splat") incorrectly removed explicit RCU grace period before freeing kioctx. The intention seems to be depending on the internal RCU grace periods of percpu_ref; however, percpu_ref uses a different flavor of RCU, sched-RCU. This can lead to kioctx being freed while RCU read protected dereferences are still in progress. Fix it by updating free_ioctx() to go through call_rcu() explicitly. v2: Comment added to explain double bouncing. Signed-off-by:
-
Al Viro authored
commit 3b821409 upstream. In case when dentry passed to lock_parent() is protected from freeing only by the fact that it's on a shrink list and trylock of parent fails, we could get hit by __dentry_kill() (and subsequent dentry_kill(parent)) between unlocking dentry and locking presumed parent. We need to recheck that dentry is alive once we lock both it and parent *and* postpone rcu_read_unlock() until after that point. Otherwise we could return a pointer to struct dentry that already is rcu-scheduled for freeing, with ->d_lock held on it; caller's subsequent attempt to unlock it can end up with memory corruption. Cc: stable@vger.kernel.org # 3.12+, counting backports Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Eric W. Biederman authored
commit 95dd7758 upstream. On nfsv2 and nfsv3 the nfs server can export subsets of the same filesystem and report the same filesystem identifier, so that the nfs client can know they are the same filesystem. The subsets can be from disjoint directory trees. The nfsv2 and nfsv3 filesystems provides no way to find the common root of all directory trees exported form the server with the same filesystem identifier. The practical result is that in struct super s_root for nfs s_root is not necessarily the root of the filesystem. The nfs mount code sets s_root to the root of the first subset of the nfs filesystem that the kernel mounts. This effects the dcache invalidation code in generic_shutdown_super currently called shrunk_dcache_for_umount and that code for years has gone through an additional list of dentries that might be dentry trees that need to be freed to accomodate nfs. When I wrote path_connected I did not realize nfs was so special, and it's hueristic for avoiding calling is_subdir can fail. The practical case where this fails is when there is a move of a directory from the subtree exposed by one nfs mount to the subtree exposed by another nfs mount. This move can happen either locally or remotely. With the remote case requiring that the move directory be cached before the move and that after the move someone walks the path to where the move directory now exists and in so doing causes the already cached directory to be moved in the dcache through the magic of d_splice_alias. If someone whose working directory is in the move directory or a subdirectory and now starts calling .. from the initial mount of nfs (where s_root == mnt_root), then path_connected as a heuristic will not bother with the is_subdir check. As s_root really is not the root of the nfs filesystem this heuristic is wrong, and the path may actually not be connected and path_connected can fail. The is_subdir function might be cheap enough that we can call it unconditionally. Verifying that will take some benchmarking and the result may not be the same on all kernels this fix needs to be backported to. So I am avoiding that for now. Filesystems with snapshots such as nilfs and btrfs do something similar. But as the directory tree of the snapshots are disjoint from one another and from the main directory tree rename won't move things between them and this problem will not occur. Cc: stable@vger.kernel.org Reported-by:
"Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by:
-
Michel Dänzer authored
commit 7d617264 upstream. Turning off the sink in this case causes various issues, because userspace expects it to stay on until it turns it off explicitly. Instead, turn the sink off and back on when a display is connected again. This dance seems necessary for link training to work correctly. Bugzilla: https://bugs.freedesktop.org/105308 Cc: stable@vger.kernel.org Reviewed-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
Michel Dänzer <michel.daenzer@amd.com> Signed-off-by:
-
Takashi Iwai authored
commit a2ff19f7 upstream. When releasing a client, we need to clear the clienttab[] entry at first, then call snd_seq_queue_client_leave(). Otherwise, the in-flight cell in the queue might be picked up by the timer interrupt via snd_seq_check_queue() before calling snd_seq_queue_client_leave(), and it's delivered to another queue while the client is clearing queues. This may eventually result in an uncleared cell remaining in a queue, and the later snd_seq_pool_delete() may need to wait for a long time until the event gets really processed. By moving the clienttab[] clearance at the beginning of release, any event delivery of a cell belonging to this client will fail at a later point, since snd_seq_client_ptr() returns NULL. Thus the cell that was picked up by the timer interrupt will be returned immediately without further delivery, and the long stall of snd_seq_delete_pool() can be avoided, too. Cc: <stable@vger.kernel.org> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Iwai authored
commit d0f83306 upstream. Although we've covered the races between concurrent write() and ioctl() in the previous patch series, there is still a possible UAF in the following scenario: A: user client closed B: timer irq -> snd_seq_release() -> snd_seq_timer_interrupt() -> snd_seq_free_client() -> snd_seq_check_queue() -> cell = snd_seq_prioq_cell_peek() -> snd_seq_prioq_leave() .... removing all cells -> snd_seq_pool_done() .... vfree() -> snd_seq_compare_tick_time(cell) ... Oops So the problem is that a cell is peeked and accessed without any protection until it's retrieved from the queue again via snd_seq_prioq_cell_out(). This patch tries to address it, also cleans up the code by a slight refactoring. snd_seq_prioq_cell_out() now receives an extra pointer argument. When it's non-NULL, the function checks the event timestamp with the given pointer. The caller needs to pass the right reference either to snd_seq_tick or snd_seq_realtime depending on the event timestamp type. A good news is that the above change allows us to remove the snd_seq_prioq_cell_peek(), too, thus the patch actually reduces the code size. Reviewed-by:
Nicolai Stange <nstange@suse.de> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Takashi Iwai authored
commit 40088dc4 upstream. With the commit 1ba8f9d3 ("ALSA: hda: Add a power_save blacklist"), we changed the default value of power_save option to -1 for processing the power-save blacklist. Unfortunately, this seems breaking user-space applications that actually read the power_save parameter value via sysfs and judge / adjust the power-saving status. They see the value -1 as if the power-save is turned off, although the actual value is taken from CONFIG_SND_HDA_POWER_SAVE_DEFAULT and it can be a positive. So, overall, passing -1 there was no good idea. Let's partially revert it -- at least for power_save option default value is restored again to CONFIG_SND_HDA_POWER_SAVE_DEFAULT. Meanwhile, in this patch, we keep the blacklist behavior and make is adjustable via the new option, pm_blacklist. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199073 Fixes: 1ba8f9d3 ("ALSA: hda: Add a power_save blacklist") Acked-by:
-
Takashi Iwai authored
commit 01c0b426 upstream. snd_pcm_oss_get_formats() has an obvious use-after-free around snd_mask_test() calls, as spotted by syzbot. The passed format_mask argument is a pointer to the hw_params object that is freed before the loop. What a surprise that it has been present since the original code of decades ago... Reported-by: syzbot+4090700a4f13fccaf648@syzkaller.appspotmail.com Cc: <stable@vger.kernel.org> Signed-off-by:
-
Toshi Kani authored
commit 18a95521 upstream. Gratian Crisan reported that vmalloc_fault() crashes when CONFIG_HUGETLBFS is not set since the function inadvertently uses pXn_huge(), which always return 0 in this case. ioremap() does not depend on CONFIG_HUGETLBFS. Fix vmalloc_fault() to call pXd_large() instead. Fixes: f4eafd8b ("x86/mm: Fix vmalloc_fault() to handle large pages properly") Reported-by:
Gratian Crisan <gratian.crisan@ni.com> Signed-off-by:
Toshi Kani <toshi.kani@hpe.com> Signed-off-by:
-
Andy Lutomirski authored
commit b5069782 upstream. POPF would trap if VIP was set regardless of whether IF was set. Fix it. Suggested-by:
Stas Sergeev <stsp@list.ru> Reported-by:
Bart Oldeman <bartoldeman@gmail.com> Signed-off-by:
Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Fixes: 5ed92a8a ("x86/vm86: Use the normal pt_regs area for vm86") Link: http://lkml.kernel.org/r/ce95f40556e7b2178b6bc06ee9557827ff94bd28.1521003603.git.luto@kernel.orgSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Andy Lutomirski authored
commit 78393fdd upstream. POPF is currently broken -- add tests to catch the error. This results in: [RUN] POPF with VIP set and IF clear from vm86 mode [INFO] Exited vm86 mode due to STI [FAIL] Incorrect return reason (started at eip = 0xd, ended at eip = 0xf) because POPF currently fails to check IF before reporting a pending interrupt. This patch also makes the FAIL message a bit more informative. Reported-by:
-
Ricardo Neri authored
commit a9e017d5 upstream. The STR and SLDT instructions are not valid when running on virtual-8086 mode and generate an invalid operand exception. These two instructions are protected by the Intel User-Mode Instruction Prevention (UMIP) security feature. In protected mode, if UMIP is enabled, these instructions generate a general protection fault if called from CPL > 0. Linux traps the general protection fault and emulates the instructions sgdt, sidt and smsw; but not str and sldt. These tests are added to verify that the emulation code does not emulate these two instructions but the expected invalid operand exception is seen. Tests fallback to exit with INT3 in case emulation does happen. Signed-off-by:
Ricardo Neri <ricardo.neri-calderon@linux.intel.com> Reviewed-by:
-
