Commits · 47c833923746decdef557d22e720ba14c81f375c · Kirill Smelkov / linux

26 Feb, 2010 40 commits

V4L/DVB (13917): gspca - zc3xx: Cleanup code. · 47c83392

Jean-Francois Moine authored Jan 07, 2010

- update copyright and module author
- change __u8/16 to u8/16
- set unsigned the sd sensor
- initialize the controls by macros
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

47c83392

V4L/DVB (13915): em28xx: fix a typo on RC6 modes · 5599678c

Mauro Carvalho Chehab authored Jan 11, 2010

Thanks to: Devin Heitmueller <dheitmueller@kernellabs.com> for double
checking it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

5599678c

V4L/DVB (13913): saa7127: Add support for generating SECAM output for the SAA712[89] chips · f05b7f5e

Andy Walls authored Jan 03, 2010

This change fixes up saa7127_s_std() generate SECAM out, if the user has
requested a 50 Hz video standard set that only contains a request for SECAM
standards and not PAL. Only the SAA712[89] chips can generate SECAM, the
SAA712[67] chips cannot.

I was unclear on the burst start and end values - I couldn't figure out
the units - so I left them the same as for the PAL systems.

A the video decoders on both a PVR-350 (SAA7115) and an HVR-1600 (CX23418)
identify the SECAM signal generated by a SAA7129 with this patch as SECAM.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

f05b7f5e

V4L/DVB (13912): cx18: Fix tuner reset pin in card entry for the Leadtek PVR2100 · a8073119

Sergey Bolshakov authored Jan 02, 2010

Fix the "xceive_pin" setting from "15" to "1" for the PVR2100 -- the same as
the PVR3100H.  This properly resets the XC2028 tuner on the PVR2100.

Sergey's original email report:

Hi.
Seems cx18 module has incorrect .xceive_pin value for card,
as i see lots of i2c errors in dmesg from xc2028.
i'm using 2.6.32.2, my hardware is:

00:09.0 Multimedia video controller [0400]: Conexant Systems, Inc. CX23418
Single-Chip MPEG-2 Encoder with Integrated Analog Video/Broadcast Audio Decoder
[14f1:5b7a]
        Subsystem: LeadTek Research Inc. Device [107d:6f27]
        Flags: bus master, medium devsel, latency 64, IRQ 17
        Memory at f0000000 (32-bit, non-prefetchable) [size=64M]
        Capabilities: [44] Vital Product Data
        Capabilities: [4c] Power Management version 2
        Kernel driver in use: cx18
        Kernel modules: cx18

Following fixes this problem for me, the rest seems working:
Reported-by: Sergey Bolshakov <sbolshakov@altlinux.ru>
Tested-by: Sergey Bolshakov <sbolshakov@altlinux.ru>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

a8073119

V4L/DVB (13910): cx18: Fix set indextable command to properly select I/P/B index entries · 5ada5773

Andy Walls authored Jan 01, 2010

The CX18_CPU_SET_INDEXTABLE command was being called with the wrong number
of arguments causing the index table frame type selection mask to be set wrong.
Now the IDX stream properly sends entries for I, P, and B frames.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

5ada5773

V4L/DVB (13909): cx18: Clean up dead code from ivtv once used for IDX processing · 9bff2d61
Andy Walls authored Dec 31, 2009
```
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
```
9bff2d61

V4L/DVB (13908): cx18: Add initial working VIDIOC_G_ENC_INDEX ioctl() support · 82acdc84