- 13 Mar, 2023 5 commits
-
-
Kristian Overskeid authored
If no frames has been exchanged with a node for HSR_NODE_FORGET_TIME, the node will be deleted from the node_db list. If a frame is sent to the node after it is deleted, a netdev_err message for each slave interface is produced. This should not happen with dan nodes because of supervision frames, but can happen often with san nodes, which clutters the kernel log. Since the hsr protocol does not support sans, this is only relevant for the prp protocol. Signed-off-by:
Kristian Overskeid <koverskeid@gmail.com> Link: https://lore.kernel.org/r/20230309092302.179586-1-koverskeid@gmail.comSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Heiner Kallweit authored
Use unified device property API. Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Link: https://lore.kernel.org/r/a969f012-1d3b-7a36-51cf-89a5f8f15a9b@gmail.comSigned-off-by:
-
Vincenzo Palazzo authored
suppress unused warnings and fix the error that there is with the W=1 enabled. Warning generated net/socket.c: In function ‘__sys_getsockopt’: net/socket.c:2300:13: error: variable ‘max_optlen’ set but not used [-Werror=unused-but-set-variable] 2300 | int max_optlen; Signed-off-by:
Vincenzo Palazzo <vincenzopalazzodev@gmail.com> Reviewed-by:
Kuniyuki Iwashima <kuniyu@amazon.com> Link: https://lore.kernel.org/r/20230310221851.304657-1-vincenzopalazzodev@gmail.comSigned-off-by:
-
Alexander Stein authored
Before putting the PHY into IEEE power down mode, disable IRQs to prevent accessing the PHY once MDIO has already been shutdown. Signed-off-by:
Alexander Stein <alexander.stein@ew.tq-group.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20230310074500.3472858-1-alexander.stein@ew.tq-group.comSigned-off-by:
-
Horatiu Vultur authored
Lan8841 has 10 GPIOs and it has 2 events(EVENT_A and EVENT_B). It is possible to assigned the 2 events to any of the GPIOs, but a GPIO can have only 1 event at a time. These events are used to generate periodic signals. It is possible to configure the length, the start time and the period of the signal by configuring the event. Currently the SW uses only EVENT_A to generate the perout. These events are generated by comparing the target time with the PHC time. In case the PHC time is changed to a value bigger than the target time + reload time, then it would generate only 1 event and then it would stop because target time + reload time is small than PHC time. Therefore it is required to change also the target time every time when the PHC is changed. The same will apply also when the PHC time is changed to a smaller value. This was tested using: testptp -L 6,2 testptp -p 1000000000 -w 200000000 Signed-off-by:
Horatiu Vultur <horatiu.vultur@microchip.com> Link: https://lore.kernel.org/r/20230307214402.793057-1-horatiu.vultur@microchip.comSigned-off-by:
-
- 11 Mar, 2023 22 commits
-
-
Muhammad Usama Anjum authored
make versioncheck reports the following: ./drivers/net/ethernet/qlogic/qede/qede.h: 10 linux/version.h not needed. ./drivers/net/ethernet/qlogic/qede/qede_ethtool.c: 7 linux/version.h not needed. So remove linux/version.h from both of these files. Also remove linux/compiler.h while at it as it is also not being used. Signed-off-by:
Muhammad Usama Anjum <usama.anjum@collabora.com> Reviewed-by:
Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20230309225206.2473644-1-usama.anjum@collabora.comSigned-off-by:
-
Edward Cree authored
EF100 can pop and/or push up to two VLAN tags. Signed-off-by:
Edward Cree <ecree.xilinx@gmail.com> Reviewed-by:
-
Jakub Kicinski authored
Siddharth Vadapalli says: ==================== Update CPSW bindings for Serdes PHY This series adds documentation for the Serdes PHY. Also, the name used to refer to the Serdes PHY in the am65-cpsw driver is updated to match the documented name. Documenting the Serdes PHY bindings was missed out in the already merged series at: https://lore.kernel.org/r/20230104103432.1126403-1-s-vadapalli@ti.com/ This miss was pointed out at: https://lore.kernel.org/r/CAMuHMdW5atq-FuLEL3htuE3t2uO86anLL3zeY7n1RqqMP_rH1g@mail.gmail.com/ v2: https://lore.kernel.org/r/20230308051835.276552-1-s-vadapalli@ti.com/ v1: https://lore.kernel.org/r/20230306094750.159657-1-s-vadapalli@ti.com/ ==================== Link: https://lore.kernel.org/r/20230309073612.431287-1-s-vadapalli@ti.comSigned-off-by:
-
Siddharth Vadapalli authored
The bindings for the am65-cpsw driver use the name "serdes" to refer to the Serdes PHY. Thus, update the name used for the Serdes PHY within the am65_cpsw_init_serdes_phy() function from "serdes-phy" to "serdes". Signed-off-by:
Siddharth Vadapalli <s-vadapalli@ti.com> Signed-off-by:
-
Siddharth Vadapalli authored
Update bindings to include Serdes PHY as an optional PHY, in addition to the existing CPSW MAC's PHY. The CPSW MAC's PHY is required while the Serdes PHY is optional. The Serdes PHY handle has to be provided only when the Serdes is being configured in a Single-Link protocol. Using the name "serdes-phy" to represent the Serdes PHY handle, the am65-cpsw-nuss driver can obtain the Serdes PHY and request the Serdes to be configured. Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
-
Vadim Fedorenko authored
Flashing firmware via devlink flash was failing on PTP OCP devices because it is using Quad SPI mode, but the driver was not properly behaving. With force_irq flag landed it now can be fixed. Signed-off-by:
Vadim Fedorenko <vadfed@meta.com> Link: https://lore.kernel.org/r/20230309105421.2953451-1-vadfed@meta.comSigned-off-by:
-
Jakub Kicinski authored
Merge tag 'wireless-next-2023-03-10' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next Johannes Berg says: ==================== wireless-next patches for 6.4 Major changes: cfg80211 * 6 GHz improvements * HW timestamping support * support for randomized auth/deauth TA for PASN privacy (also for mac80211) mac80211 * radiotap TLV and EHT support for the iwlwifi sniffer * HW timestamping support * per-link debugfs for multi-link brcmfmac * support for Apple (M1 Pro/Max) devices iwlwifi * support for a few new devices * EHT sniffer support rtw88 * better support for some SDIO devices (e.g. MAC address from efuse) rtw89 * HW scan support for 8852b * better support for 6 GHz scanning * tag 'wireless-next-2023-03-10' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (84 commits) wifi: iwlwifi: mvm: fix EOF bit reporting wifi: iwlwifi: Do not include radiotap EHT user info if not needed wifi: iwlwifi: mvm: add EHT RU allocation to radiotap wifi: iwlwifi: Update logs for yoyo reset sw changes wifi: iwlwifi: mvm: clean up duplicated defines wifi: iwlwifi: rs-fw: break out for unsupported bandwidth wifi: iwlwifi: Add support for B step of BnJ-Fm4 wifi: iwlwifi: mvm: make flush code a bit clearer wifi: iwlwifi: mvm: avoid UB shift of snif_queue wifi: iwlwifi: mvm: add primary 80 known for EHT radiotap wifi: iwlwifi: mvm: parse FW frame metadata for EHT sniffer mode wifi: iwlwifi: mvm: decode USIG_B1_B7 RU to nl80211 RU width wifi: iwlwifi: mvm: rename define to generic name wifi: iwlwifi: mvm: allow Microsoft to use TAS wifi: iwlwifi: mvm: add all EHT based on data0 info from HW wifi: iwlwifi: mvm: add EHT radiotap info based on rate_n_flags wifi: iwlwifi: mvm: add an helper function radiotap TLVs wifi: radiotap: separate vendor TLV into header/content wifi: iwlwifi: reduce verbosity of some logging events wifi: iwlwifi: Adding the code to get RF name for MsP device ... ==================== Link: https://lore.kernel.org/r/20230310120159.36518-1-johannes@sipsolutions.netSigned-off-by:
-
Jakub Kicinski authored
Russell King says: ==================== Rework SFP A2 access conditionals This series reworks the SFP A2 (diagnostics and control) access so we don't end up testing a variable number of conditions in several places. This also resolves a minor issue where we may have a module indicating that it is not SFF8472 compliant, doesn't implement A2, but fails to set the enhanced option byte to zero, leading to accesses to the A2 page that fail. The first patch adds a new flag "have_a2" which indicates whether we should be accessing the A2 page, and uses this for hwmon. The conditions are kept the same. The second patch extends the check for soft-state polling and control by using this "have_a2" flag (which effectively augments the check to include some level of SFF8472 compliance.) ==================== Link: https://lore.kernel.org/r/ZAoBnqGBnIZzLwpV@shell.armlinux.org.ukSigned-off-by:
-
Russell King (Oracle) authored
The soft state bits are stored in the A2h memory space, and require SFF-8472 compliance. This is what our have_a2 flag tells us, so use this to indicate whether we should attempt to use the soft signals. Signed-off-by:
Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by:
-
Russell King (Oracle) authored
The hwmon code wants to know when it is safe to access the A2h data stored in a separate address. We indicate that this is present when we have SFF-8472 compliance and the lack of an address-change sequence., The same conditions are also true if we want to access other controls and status in the A2h address. So let's make a flag to indicate whether we can access it, instead of repeating the conditions throughout the code. For now, only convert the hwmon code. Signed-off-by:
-
Jakub Kicinski authored
Gal Pressman says: ==================== Couple of minor improvements to build_skb variants First patch replaces open-coded occurrences of skb_propagate_pfmemalloc() in build_skb() and build_skb_around(). The secnod patch adds a likely() to the skb allocation in build_skb(). ==================== Link: https://lore.kernel.org/r/20230308131720.2103611-1-gal@nvidia.comSigned-off-by:
-
Gal Pressman authored
Similarly to napi_build_skb(), it is likely the skb allocation in build_skb() succeeded. frag_size != 0 is also likely, as stated in __build_skb_around(). Reviewed-by:
Tariq Toukan <tariqt@nvidia.com> Signed-off-by:
Gal Pressman <gal@nvidia.com> Reviewed-by:
Larysa Zaremba <larysa.zaremba@intel.com> Reviewed-by:
-
Gal Pressman authored
Use skb_propagate_pfmemalloc() in build_skb()/build_skb_around() instead of open-coding it. Reviewed-by:
-
Jens Axboe authored
The tap driver already supports passing in nonblocking state based on O_NONBLOCK, add support for checking IOCB_NOWAIT as well. With that done, we can flag it with FMODE_NOWAIT as well. Signed-off-by:
Jens Axboe <axboe@kernel.dk> Link: https://lore.kernel.org/r/8f859870-e6e2-09ca-9c0f-a2aa7c984fb2@kernel.dkSigned-off-by:
-
Jens Axboe authored
tun already checks for both O_NONBLOCK and IOCB_NOWAIT in its read and write iter handlers, so it's fully ready for FMODE_NOWAIT. But for some reason it doesn't set it. Rectify that oversight. Signed-off-by:
-
Jakub Kicinski authored
Horatiu Vultur says: ==================== net: lan966x: Add support for IS1 VCAP Provide the Ingress Stage 1 (IS1) VCAP (Versatile Content-Aware Processor) support for the Lan966x platform. The IS1 VCAP has 3 lookups and they are accessible with a TC chain id: - chain 1000000: IS1 Lookup 0 - chain 1100000: IS1 Lookup 1 - chain 1200000: IS1 Lookup 2 The IS1 is capable of different actions like rewrite VLAN tags, change priority of the frames, police the traffic, etc. These features will be added at a later point. The IS1 currently implements the action that allows setting the value of a PAG (Policy Association Group) key field in the frame metadata and this can be used for matching in an IS2 VCAP rule. In this way a rule in IS0 VCAP can be linked to rules in the IS2 VCAP. The linking is exposed by using the TC "goto chain" action with an offset from the IS2 chain ids. For example "goto chain 8000001" will use a PAG value of 1 to chain to a rule in IS2 lookup 0. ==================== Link: https://lore.kernel.org/r/20230307220929.834219-1-horatiu.vultur@microchip.comSigned-off-by:
-
Horatiu Vultur authored
IS1 VCAP has it's own list of supported ethernet protocol types which is different than the IS2 VCAP. Therefore separate the list of known protocol types based on the VCAP type. Signed-off-by:
-
Horatiu Vultur authored
Allow rules to be chained between IS1 VCAP and IS2 VCAP. Chaining between IS1 lookups or between IS2 lookups are not supported by the hardware. Signed-off-by:
-
Horatiu Vultur authored
Enable TC command to use IS1 VCAP Signed-off-by:
-
Horatiu Vultur authored
Add IS1 VCAP port keyset configuration for lan966x and also update debug fs support to show the keyset configuration. Signed-off-by:
-
Horatiu Vultur authored
Provide IS1 (ingress stage 1) VCAP model for lan966x. This provides classification actions for lan966x. Signed-off-by:
-
Miquel Raynal authored
NVMEM layouts are no longer registered early, and thus may not yet be available when Ethernet drivers (or any other consumer) probe, leading to possible probe deferrals errors. Forward the error code if this happens. All other errors being discarded, the driver will eventually use a random MAC address if no other source was considered valid (no functional change on this regard). Signed-off-by:
Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by:
Marcin Wojtas <mw@semihalf.com> Link: https://lore.kernel.org/r/20230307192927.512757-1-miquel.raynal@bootlin.comSigned-off-by:
-
- 10 Mar, 2023 12 commits
-
-
Bjorn Helgaas authored
The filename "wangxun" sorts between "intel" and "xscale", but xscale/Kconfig contains "Intel XScale" prompts, so Wangxun ends up in the wrong place in the config front-ends. Move wangxun/Kconfig so the Wangxun devices appear in order in the user interface. Fixes: 3ce7547e ("net: txgbe: Add build support for txgbe") Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Link: https://lore.kernel.org/r/20230307221051.890135-1-helgaas@kernel.orgSigned-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queueJakub Kicinski authored
Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2023-03-07 (igc) This series contains updates to igc driver only. Muhammad adds tracking and reporting of QBV config errors. Tan Tee adds support for configuring max SDU for each Tx queue. Sasha removes check for alternate media as only one media type is supported. * '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue: igc: Clean up and optimize watchdog task igc: offload queue max SDU from tc-taprio igc: Add qbv_config_change_errors counter ==================== Link: https://lore.kernel.org/r/20230307221332.3997881-1-anthony.l.nguyen@intel.comSigned-off-by:
-
Jason Xing authored
Keep the accounting schema consistent across different protocols with __sk_mem_schedule(). Besides, it adjusts a little bit on how to calculate forward allocated memory compared to before. After applied this patch, we could avoid receive path scheduling extra amount of memory. Link: https://lore.kernel.org/lkml/20230221110344.82818-1-kerneljasonxing@gmail.com/Signed-off-by:
Jason Xing <kernelxing@tencent.com> Reviewed-by:
Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20230308021153.99777-1-kerneljasonxing@gmail.comSigned-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-nextJakub Kicinski authored
Florian Westphal says: ==================== Netfilter updates for net-next 1. nf_tables 'brouting' support, from Sriram Yagnaraman. 2. Update bridge netfilter and ovs conntrack helpers to handle IPv6 Jumbo packets properly, i.e. fetch the packet length from hop-by-hop extension header, from Xin Long. This comes with a test BIG TCP test case, added to tools/testing/selftests/net/. 3. Fix spelling and indentation in conntrack, from Jeremy Sowden. * 'main' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next: netfilter: nat: fix indentation of function arguments netfilter: conntrack: fix typo selftests: add a selftest for big tcp netfilter: use nf_ip6_check_hbh_len in nf_ct_skb_network_trim netfilter: move br_nf_check_hbh_len to utils netfilter: bridge: move pskb_trim_rcsum out of br_nf_check_hbh_len netfilter: bridge: check len before accessing more nh data netfilter: bridge: call pskb_may_pull in br_nf_check_hbh_len netfilter: bridge: introduce broute meta statement ==================== Link: https://lore.kernel.org/r/20230308193033.13965-1-fw@strlen.deSigned-off-by:
-
Geert Uytterhoeven authored
Use the new devm_of_phy_optional_get() helper instead of open-coding the same operation. Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by:
-
Leon Romanovsky authored
neigh_lookup_nodev isn't used in the kernel after removal of DECnet. So let's remove it. Fixes: 1202cdd6 ("Remove DECnet support from kernel") Signed-off-by:
Leon Romanovsky <leonro@nvidia.com> Reviewed-by:
Nikolay Aleksandrov <razor@blackwall.org> Link: https://lore.kernel.org/r/eb5656200d7964b2d177a36b77efa3c597d6d72d.1678267343.git.leonro@nvidia.comSigned-off-by:
-
Eric Dumazet authored
This field mirrors hrtimer softexpires, we can instead use the existing helpers. Signed-off-by:
-
Heiner Kallweit authored
Simplify the code by using phy_set_bits(). Signed-off-by:
-
Florian Westphal authored
No users in the tree. Tested with allmodconfig build. Signed-off-by:
Florian Westphal <fw@strlen.de> Link: https://lore.kernel.org/r/20230308142006.20879-1-fw@strlen.deSigned-off-by:
-
Nick Alcock authored
Since commit 8b41fc44 ("kbuild: create modules.builtin without Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations are used to identify modules. As a consequence, uses of the macro in non-modules will cause modprobe to misidentify their containing object file as a module when it is not (false positives), and modprobe might succeed rather than failing with a suitable error message. So remove it in the files in this commit, none of which can be built as modules. Signed-off-by:
Nick Alcock <nick.alcock@oracle.com> Suggested-by:
Luis Chamberlain <mcgrof@kernel.org> Cc: Hitomi Hasegawa <hasegawa-hitomi@fujitsu.com> Cc: Vladimir Oltean <olteanv@gmail.com> Link: https://lore.kernel.org/r/20230308121230.5354-1-nick.alcock@oracle.comSigned-off-by:
-
Nick Alcock authored
Since commit 8b41fc44 ("kbuild: create modules.builtin without Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations are used to identify modules. As a consequence, uses of the macro in non-modules will cause modprobe to misidentify their containing object file as a module when it is not (false positives), and modprobe might succeed rather than failing with a suitable error message. So remove it in the files in this commit, none of which can be built as modules. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski authored
Documentation/bpf/bpf_devel_QA.rst b7abcd9c ("bpf, doc: Link to submitting-patches.rst for general patch submission info") d56b0c46 ("bpf, docs: Fix link to netdev-FAQ target") https://lore.kernel.org/all/20230307095812.236eb1be@canb.auug.org.au/Signed-off-by:
-
- 09 Mar, 2023 1 commit
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds authored
Pull networking fixes from Paolo Abeni: "Including fixes from netfilter and bpf. Current release - regressions: - core: avoid skb end_offset change in __skb_unclone_keeptruesize() - sched: - act_connmark: handle errno on tcf_idr_check_alloc - flower: fix fl_change() error recovery path - ieee802154: prevent user from crashing the host Current release - new code bugs: - eth: bnxt_en: fix the double free during device removal - tools: ynl: - fix enum-as-flags in the generic CLI - fully inherit attrs in subsets - re-license uniformly under GPL-2.0 or BSD-3-clause Previous releases - regressions: - core: use indirect calls helpers for sk_exit_memory_pressure() - tls: - fix return value for async crypto - avoid hanging tasks on the tx_lock - eth: ice: copy last block omitted in ice_get_module_eeprom() Previous releases - always broken: - core: avoid double iput when sock_alloc_file fails - af_unix: fix struct pid leaks in OOB support - tls: - fix possible race condition - fix device-offloaded sendpage straddling records - bpf: - sockmap: fix an infinite loop error - test_run: fix &xdp_frame misplacement for LIVE_FRAMES - fix resolving BTF_KIND_VAR after ARRAY, STRUCT, UNION, PTR - netfilter: tproxy: fix deadlock due to missing BH disable - phylib: get rid of unnecessary locking - eth: bgmac: fix *initial* chip reset to support BCM5358 - eth: nfp: fix csum for ipsec offload - eth: mtk_eth_soc: fix RX data corruption issue Misc: - usb: qmi_wwan: add telit 0x1080 composition" * tag 'net-6.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (64 commits) tools: ynl: fix enum-as-flags in the generic CLI tools: ynl: move the enum classes to shared code net: avoid double iput when sock_alloc_file fails af_unix: fix struct pid leaks in OOB support eth: fealnx: bring back this old driver net: dsa: mt7530: permit port 5 to work without port 6 on MT7621 SoC net: microchip: sparx5: fix deletion of existing DSCP mappings octeontx2-af: Unlock contexts in the queue context cache in case of fault detection net/smc: fix fallback failed while sendmsg with fastopen ynl: re-license uniformly under GPL-2.0 OR BSD-3-Clause mailmap: update entries for Stephen Hemminger mailmap: add entry for Maxim Mikityanskiy nfc: change order inside nfc_se_io error path ethernet: ice: avoid gcc-9 integer overflow warning ice: don't ignore return codes in VSI related code ice: Fix DSCP PFC TLV creation net: usb: qmi_wwan: add Telit 0x1080 composition net: usb: cdc_mbim: avoid altsetting toggling for Telit FE990 netfilter: conntrack: adopt safer max chain length net: tls: fix device-offloaded sendpage straddling records ...
-
